Merge branch 'for-next/hugepages' of git://git.linaro.org/people/stevecapper/linux into upstream-hugepages
* 'for-next/hugepages' of git://git.linaro.org/people/stevecapper/linux:
ARM64: mm: THP support.
ARM64: mm: Raise MAX_ORDER for 64KB pages and THP.
ARM64: mm: HugeTLB support.
ARM64: mm: Move PTE_PROT_NONE bit.
ARM64: mm: Make PAGE_NONE pages read only and no-execute.
ARM64: mm: Restore memblock limit when map_mem finished.
mm: thp: Correct the HPAGE_PMD_ORDER check.
x86: mm: Remove general hugetlb code from x86.
mm: hugetlb: Copy general hugetlb code from x86 to mm.
x86: mm: Remove x86 version of huge_pmd_share.
mm: hugetlb: Copy huge_pmd_share from x86 to mm.
Steve Capper [Fri, 19 Apr 2013 15:23:57 +0000 (16:23 +0100)]
ARM64: mm: THP support.
Bring Transparent HugePage support to ARM. The size of a
transparent huge page depends on the normal page size. A
transparent huge page is always represented as a pmd.
If PAGE_SIZE is 4KB, THPs are 2MB.
If PAGE_SIZE is 64KB, THPs are 512MB.
Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Steve Capper [Thu, 25 Apr 2013 14:19:21 +0000 (15:19 +0100)]
ARM64: mm: Raise MAX_ORDER for 64KB pages and THP.
The buddy allocator has a default MAX_ORDER of 11, which is too
low to allocate enough memory for 512MB Transparent HugePages if
our base page size is 64KB.
This patch introduces MAX_ZONE_ORDER and sets it to 14 when 64KB
pages are used in conjuction with THP, otherwise the default value
of 11 is used.
Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Steve Capper [Wed, 10 Apr 2013 12:48:00 +0000 (13:48 +0100)]
ARM64: mm: HugeTLB support.
Add huge page support to ARM64, different huge page sizes are
supported depending on the size of normal pages:
PAGE_SIZE is 4KB:
2MB - (pmds) these can be allocated at any time.
1024MB - (puds) usually allocated on bootup with the command line
with something like: hugepagesz=1G hugepages=6
PAGE_SIZE is 64KB:
512MB - (pmds) usually allocated on bootup via command line.
Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Steve Capper [Tue, 28 May 2013 12:35:51 +0000 (13:35 +0100)]
ARM64: mm: Move PTE_PROT_NONE bit.
Under ARM64, PTEs can be broadly categorised as follows:
- Present and valid: Bit #0 is set. The PTE is valid and memory
access to the region may fault.
- Present and invalid: Bit #0 is clear and bit #1 is set.
Represents present memory with PROT_NONE protection. The PTE
is an invalid entry, and the user fault handler will raise a
SIGSEGV.
- Not present (file or swap): Bits #0 and #1 are clear.
Memory represented has been paged out. The PTE is an invalid
entry, and the fault handler will try and re-populate the
memory where necessary.
Huge PTEs are block descriptors that have bit #1 clear. If we wish
to represent PROT_NONE huge PTEs we then run into a problem as
there is no way to distinguish between regular and huge PTEs if we
set bit #1.
To resolve this ambiguity this patch moves PTE_PROT_NONE from
bit #1 to bit #2 and moves PTE_FILE from bit #2 to bit #3. The
number of swap/file bits is reduced by 1 as a consequence, leaving
60 bits for file and swap entries.
Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Steve Capper [Tue, 30 Apr 2013 10:00:33 +0000 (11:00 +0100)]
ARM64: mm: Restore memblock limit when map_mem finished.
In paging_init the memblock limit is set to restrict any addresses
returned by early_alloc to fit within the initial direct kernel
mapping in swapper_pg_dir. This allows map_mem to allocate puds,
pmds and ptes from the initial direct kernel mapping.
The limit stays low after paging_init() though, meaning any
bootmem allocations will be from a restricted subset of memory.
Gigabyte huge pages, for instance, are normally allocated from
bootmem as their order (18) is too large for the default buddy
allocator (MAX_ORDER = 11).
This patch restores the memblock limit when map_mem has finished,
allowing gigabyte huge pages (and other objects) to be allocated
from all of bootmem.
Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Steve Capper [Tue, 7 May 2013 13:46:03 +0000 (14:46 +0100)]
mm: thp: Correct the HPAGE_PMD_ORDER check.
All Transparent Huge Pages are allocated by the buddy allocator.
A compile time check is in place that fails when the order of a
transparent huge page is too large to be allocated by the buddy
allocator. Unfortunately that compile time check passes when:
HPAGE_PMD_ORDER == MAX_ORDER
( which is incorrect as the buddy allocator can only allocate
memory of order strictly less than MAX_ORDER. )
This patch updates the compile time check to fail in the above
case.
Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Andrew Morton <akpm@linux-foundation.org>
Steve Capper [Tue, 30 Apr 2013 07:02:03 +0000 (08:02 +0100)]
mm: hugetlb: Copy general hugetlb code from x86 to mm.
The huge_pte_alloc, huge_pte_offset and follow_huge_p[mu]d
functions in x86/mm/hugetlbpage.c do not rely on any architecture
specific knowledge other than the fact that pmds and puds can be
treated as huge ptes.
To allow other architectures to use this code (and reduce the need
for code duplication), this patch copies these functions into mm,
replaces the use of pud_large with pud_huge and provides a config
flag to activate them:
CONFIG_ARCH_WANT_GENERAL_HUGETLB
If CONFIG_ARCH_WANT_HUGE_PMD_SHARE is also active then the
huge_pmd_share code will be called by huge_pte_alloc (othewise we
call pmd_alloc and skip the sharing code).
Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Andrew Morton <akpm@linux-foundation.org>
Steve Capper [Tue, 23 Apr 2013 11:35:02 +0000 (12:35 +0100)]
mm: hugetlb: Copy huge_pmd_share from x86 to mm.
Under x86, multiple puds can be made to reference the same bank of
huge pmds provided that they represent a full PUD_SIZE of shared
huge memory that is aligned to a PUD_SIZE boundary.
The code to share pmds does not require any architecture specific
knowledge other than the fact that pmds can be indexed, thus can
be beneficial to some other architectures.
This patch copies the huge pmd sharing (and unsharing) logic from
x86/ to mm/ and introduces a new config option to activate it:
CONFIG_ARCH_WANTS_HUGE_PMD_SHARE
Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Andrew Morton <akpm@linux-foundation.org>
Catalin Marinas [Wed, 12 Jun 2013 15:11:35 +0000 (16:11 +0100)]
Merge tag 'xen-arm64-3.1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen into upstream
Introduce Xen support to ARM64
* tag 'xen-arm64-3.1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen:
MAINTAINERS: add myself as arm64/xen maintainer
arm64/xen: introduce CONFIG_XEN and hypercall.S on ARM64
arm64/xen: use XEN_IO_PROTO_ABI_ARM on ARM64
arm64/xen: implement ioremap_cached on arm64
arm64/xen: introduce asm/xen header files on arm64
arm/xen: define xen_remap as ioremap_cached
The software breakpoint handlers are hooked in directly from ptrace,
which makes it difficult to add additional handlers for things like
kprobes and kgdb.
This patch moves the handling code into debug-monitors.c, where we can
dispatch to different debug subsystems more easily.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Wed, 8 May 2013 16:29:24 +0000 (17:29 +0100)]
arm64: extable: sort the exception table at build time
As is done for other architectures, sort the exception table at
build-time rather than during boot.
Since sortextable appears to be a standalone C program relying on the
host elf.h to provide EM_AARCH64, I've had to add a conditional check in
order to allow cross-compilation on machines that aren't running a
bleeding-edge libc-dev.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Mon, 10 Jun 2013 18:34:42 +0000 (19:34 +0100)]
arm64: device: add iommu pointer to device archdata
When using an IOMMU for device mappings, it is necessary to keep a
pointer between the device and the IOMMU to which it is attached in
order to obtain the correct IOMMU when attaching the device to a domain.
This patch adds an iommu pointer to the dev_archdata structure, in a
similar manner to other architectures (ARM, PowerPC, x86, ...).
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Mon, 10 Jun 2013 18:34:41 +0000 (19:34 +0100)]
arm64: pgtable: use pte_index instead of __pte_index
pte_index is a useful helper outside of arch/arm64, for things like the
ARM SMMU driver, so rename __pte_index to pte_index to be consistent
with both arch/arm/ and also the definitions of pmd_index and pgd_index.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Chen Gang [Tue, 21 May 2013 09:46:05 +0000 (10:46 +0100)]
arm64: kernel: compiling issue, need delete read_current_timer()
Under arm64, we will calibrate the delay loop statically using a known
timer frequency, so delete read_current_timer(), or it will cause
compiling issue with allmodconfig.
The related error:
ERROR: "read_current_timer" [lib/rbtree_test.ko] undefined!
ERROR: "read_current_timer" [lib/interval_tree_test.ko] undefined!
ERROR: "read_current_timer" [fs/ext4/ext4.ko] undefined!
ERROR: "read_current_timer" [crypto/tcrypt.ko] undefined!
Signed-off-by: Chen Gang <gang.chen@asianux.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Fri, 31 May 2013 15:30:58 +0000 (16:30 +0100)]
arm64: spinlock: retry trylock operation if strex fails on free lock
An exclusive store instruction may fail for reasons other than lock
contention (e.g. a cache eviction during the critical section) so, in
line with other architectures using similar exclusive instructions
(alpha, mips, powerpc), retry the trylock operation if the lock appears
to be free but the strex reported failure.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Tony Thompson <anthony.thompson@arm.com> Acked-by: Will Deacon <will.deacon@arm.com>
Catalin Marinas [Wed, 1 May 2013 15:38:23 +0000 (16:38 +0100)]
arm64: Remove __flush_dcache_page()
This function is only used in __sync_icache_dcache(), so remove it and
call __flush_dcache_area() directly. The flush_icache_user_range()
function is not used in the arm64 kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Will Deacon <will.deacon@arm.com> Acked-by: Will Deacon <will.deacon@arm.com>
Catalin Marinas [Wed, 1 May 2013 11:23:05 +0000 (12:23 +0100)]
arm64: Avoid cache flushing in flush_dcache_page()
The flush_dcache_page() function is called when the kernel modified a
page cache page. Since the D-cache on AArch64 does not have aliases
this function can simply mark the page as dirty for later flushing via
set_pte_at()/__sync_icache_dcache() if the page is executable (to ensure
the I-D cache coherency).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Will Deacon <will.deacon@arm.com> Acked-by: Will Deacon <will.deacon@arm.com>
arm64: Provide default implementation for dma_{alloc,free}_attrs
Most architectures that define CONFIG_HAS_DMA, have implementations for
both dma_alloc_attrs() and dma_free_attrs(). All achitectures that do
not define CONFIG_HAS_DMA also have both of these definitions provided
by dma-mapping-broken.h.
Add default implementations for these functions on arm64.
arm64/xen: introduce asm/xen header files on arm64
asm/xen/hypercall.h, asm/xen/hypervisor.h, asm/xen/interface.h and
asm/xen/page.h are identical so to avoid code duplication we are just
including the original arm header files here.
asm/xen/events.h is slightly different, so introduce a different file
here (use xchg to implement xchg_xen_ulong and pass regs->pstate to
raw_irqs_disabled_flags).
Also introduce asm/hypervisor.h and asm/sync_bitops.h.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com>
Linus Torvalds [Sat, 1 Jun 2013 21:24:54 +0000 (06:24 +0900)]
Merge branch 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This patcheset includes fixes for:
- the PCI/LBA which brings back the stifb graphics framebuffer
console
- possible memory overflows in parisc kernel init code
- parport support on older GSC machines
- avoids that users by mistake enable PARPORT_PC_SUPERIO on parisc
- MAINTAINERS file list updates for parisc."
* 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: parport0: fix this legacy no-device port driver!
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
parisc/PCI: Set type for LBA bus_num resource
MAINTAINERS: update parisc architecture file list
parisc: kernel: using strlcpy() instead of strcpy()
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
parisc: memory overflow, 'name' length is too short for using
Helge Deller [Thu, 30 May 2013 21:06:39 +0000 (21:06 +0000)]
parisc: parport0: fix this legacy no-device port driver!
Fix the above kernel error from parport_announce_port() on 32bit GSC
machines (e.g. B160L). The parport driver requires now a pointer to the
device struct.
Helge Deller [Thu, 30 May 2013 16:24:46 +0000 (16:24 +0000)]
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
If enabled, CONFIG_PARPORT_PC_SUPERIO scans on PC-like hardware for
various super-io chips by accessing i/o ports in a range which will
crash any parisc hardware at once.
In addition, parisc has it's own incompatible superio chip
(CONFIG_SUPERIO), so if we disable PARPORT_PC_SUPERIO completely for
parisc we can avoid that people by accident enable the parport_pc
superio option too.
Helge Deller [Fri, 31 May 2013 22:24:58 +0000 (22:24 +0000)]
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
commit dc7dce280a
Author: Bjorn Helgaas <bhelgaas@google.com>
Date: Fri Oct 28 16:27:27 2011 -0600
parisc/PCI: lba: convert to pci_create_root_bus() for correct root bus
resources
Supply root bus resources to pci_create_root_bus() so they're correct
immediately. This fixes the problem of "early" and "header" quirks seeing
incorrect root bus resources.
added tests for elmmio_space.start while it should use
elmmio_space.flags. This for example led to incorrect resource
assignments and a non-working stifb framebuffer on most parisc machines.
LBA 10:1: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io 0x12000-0x13fff] (bus address [0x2000-0x3fff])
pci_bus 0000:01: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
Bjorn Helgaas [Thu, 30 May 2013 17:45:39 +0000 (11:45 -0600)]
parisc/PCI: Set type for LBA bus_num resource
The non-PAT resource probing code failed to set the type of the LBA bus_num
resource (30aa80da43 "parisc/PCI: register busn_res for root buses" did
the corresponding thing for the PAT case).
This causes incorrect resource assignments and a non-working stifb
framebuffer on most parisc machines.
Paul Bolle [Wed, 29 May 2013 09:56:58 +0000 (09:56 +0000)]
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
There's a Makefile line setting cflags for CONFIG_PA7100. But that
Kconfig macro doesn't exist. There is a Kconfig symbol PA7000, which
covers both PA7000 and PA7100 processors. So let's use the corresponding
Kconfig macro.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Tue, 28 May 2013 20:35:54 +0000 (20:35 +0000)]
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
With CONFIG_DISCONTIGMEM=y and multiple physical memory areas,
cat /proc/kpageflags triggers this kernel bug:
kernel BUG at arch/parisc/include/asm/mmzone.h:50!
CPU: 2 PID: 7848 Comm: cat Tainted: G D W 3.10.0-rc3-64bit #44
IAOQ[0]: kpageflags_read0x128/0x238
IAOQ[1]: kpageflags_read0x12c/0x238
RP(r2): proc_reg_read0xbc/0x130
Backtrace:
[<00000000402ca2d4>] proc_reg_read0xbc/0x130
[<0000000040235bcc>] vfs_read0xc4/0x1d0
[<0000000040235f0c>] SyS_read0x94/0xf0
[<0000000040105fc0>] syscall_exit0x0/0x14
kpageflags_read() walks through the whole memory, even if some memory
areas are physically not available. So, we should better not BUG on an
unavailable pfn in pfn_to_nid() but just return the expected value -1 or
0.
Linus Torvalds [Sat, 1 Jun 2013 11:13:16 +0000 (20:13 +0900)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few more fixes for powerpc 3.10. It's a bit more than I
would have liked this late in the game but I suppose that's what
happens with a brand new chip generation coming out.
A few regression fixes, some last minute fixes for new P8 features
such as transactional memory,...
There's also one powerpc KVM patch that I requested that adds two
missing functions to our in-kernel interrupt controller support which
is itself a new 3.10 feature. These are defined by the base
hypervisor specification. We didn't implement them originally because
Linux doesn't use them but they are simple and I'm not comfortable
having a half-implemented interface in 3.10 and having to deal with
versionning etc... later when something starts needing those calls.
They cannot be emulated in qemu when using in-kernel interrupt
controller (not enough shared state).
Just added a last minute patch to fix a typo introducing a breakage in
our cputable for Power7+ processors, sorry about that, but the
regression it fixes just hurt me :-)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/cputable: Fix typo on P7+ cputable entry
powerpc/perf: Add missing SIER support
powerpc/perf: Revert to original NO_SIPR logic
powerpc/pci: Remove the unused variables in pci_process_bridge_OF_ranges
powerpc/pci: Remove the stale comments of pci_process_bridge_OF_ranges
powerpc/pseries: Always enable CONFIG_HOTPLUG_CPU on PSERIES SMP
powerpc/kvm/book3s: Add support for H_IPOLL and H_XIRR_X in XICS emulation
powerpc/32bit:Store temporary result in r0 instead of r8
powerpc/mm: Always invalidate tlb on hpte invalidate and update
powerpc/pseries: Improve stream generation comments in copypage/user
powerpc/pseries: Kill all prefetch streams on context switch
powerpc/cputable: Fix oprofile_cpu_type on power8
powerpc/mpic: Fix irq distribution problem when MPIC_SINGLE_DEST_CPU
powerpc/tm: Fix userspace stack corruption on signal delivery for active transactions
powerpc/tm: Move TM abort cause codes to uapi
powerpc/tm: Abort on emulation and alignment faults
powerpc/tm: Update cause codes documentation
powerpc/tm: Make room for hypervisor in abort cause codes
Pull scsi target fixes from Nicholas Bellinger:
"The highlights include:
- Re-instate sess->wait_list in target_wait_for_sess_cmds() for
active I/O shutdown handling in fabrics using se_cmd->cmd_kref
- Make ib_srpt call target_sess_cmd_list_set_waiting() during session
shutdown
- Fix FILEIO off-by-one READ_CAPACITY bug for !S_ISBLK export
- Fix iscsi-target login error heap buffer overflow (Kees)
- Fix iscsi-target active I/O shutdown handling regression in
v3.10-rc1
A big thanks to Kees Cook for fixing a long standing login error
buffer overflow bug.
All patches are CC'ed to stable with the exception of the v3.10-rc1
specific regression + other minor target cleanup."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix iscsit_free_cmd() se_cmd->cmd_kref shutdown handling
target: Propigate up ->cmd_kref put return via transport_generic_free_cmd
iscsi-target: fix heap buffer overflow on error
target/file: Fix off-by-one READ_CAPACITY bug for !S_ISBLK export
ib_srpt: Call target_sess_cmd_list_set_waiting during shutdown_session
target: Re-instate sess_wait_list for target_wait_for_sess_cmds
target: Remove unused wait_for_tasks bit in target_wait_for_sess_cmds
Linus Torvalds [Sat, 1 Jun 2013 10:55:26 +0000 (19:55 +0900)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock subsystem fixes from Mike Turquette:
"A mix of small fixes affecting mostly ARM platforms as well as a
discrete clock expander chip. Most fixes are corrections to lousy
clock data of one form or another."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: Include clk mxs header file
clk: vt8500: Fix unbalanced spinlock in vt8500_dclk_set_rate()
clk: si5351: Set initial clkout rate when defined in platform data.
clk: si5351: Fix clkout rate computation.
clk: samsung: Add CLK_IGNORE_UNUSED flag for the sysreg clocks
clk: ux500: clk-sysctrl: handle clocks with no parents
clk: ux500: Provide device enumeration number suffix for SMSC911x
Linus Torvalds [Sat, 1 Jun 2013 10:51:52 +0000 (19:51 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull assorted fixes from Al Viro:
"There'll be more - I'm trying to dig out from under the pile of mail
(a couple of weeks of something flu-like ;-/) and there's several more
things waiting for review; this is just the obvious stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
zoran: racy refcount handling in vm_ops ->open()/->close()
befs_readdir(): do not increment ->f_pos if filldir tells us to stop
hpfs: deadlock and race in directory lseek()
qnx6: qnx6_readdir() has a braino in pos calculation
fix buffer leak after "scsi: saner replacements for ->proc_info()"
vfs: Fix invalid ida_remove() call
Linus Torvalds [Sat, 1 Jun 2013 10:48:59 +0000 (19:48 +0900)]
Merge tag 'nfs-for-3.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull two NFS client fixes from Trond Myklebust:
- Fix a regression that broke NFS mounting using klibc and busybox
- Stable fix to check access modes correctly on NFSv4 delegated open()
* tag 'nfs-for-3.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix security flavor negotiation with legacy binary mounts
NFSv4: Fix a thinko in nfs4_try_open_cached
Will Schmidt [Mon, 20 May 2013 05:04:18 +0000 (05:04 +0000)]
powerpc/cputable: Fix typo on P7+ cputable entry
Fix a typo in setting COMMON_USER2_POWER7 bits to .cpu_user_features2
cpu specs table.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com> Acked-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Srivatsa S. Bhat [Tue, 21 May 2013 09:32:48 +0000 (09:32 +0000)]
powerpc/pseries: Always enable CONFIG_HOTPLUG_CPU on PSERIES SMP
Adam Lackorzynski reported the following build failure on
!CONFIG_HOTPLUG_CPU configuration:
CC arch/powerpc/kernel/rtas.o
arch/powerpc/kernel/rtas.c: In function ‘rtas_cpu_state_change_mask’:
arch/powerpc/kernel/rtas.c:843:4: error: implicit declaration of function ‘cpu_down’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/kernel/rtas.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
The build fails because cpu_down() is defined only under CONFIG_HOTPLUG_CPU.
Looking further, the mobility code in pseries is one of the call-sites which
uses rtas_ibm_suspend_me(), which in turn calls rtas_cpu_state_change_mask().
And the mobility code is unconditionally compiled-in (it does not fall under
any Kconfig option). And commit 120496ac (powerpc: Bring all threads online
prior to migration/hibernation) which introduced this build regression is
critical for the proper functioning of the migration code. So it appears
that the only solution to this problem is to enable CONFIG_HOTPLUG_CPU if
SMP is enabled on PPC_PSERIES platforms. So make that change in the Kconfig.
Reported-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de> Cc: stable@vger.kernel.org Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Thu, 23 May 2013 15:42:21 +0000 (15:42 +0000)]
powerpc/kvm/book3s: Add support for H_IPOLL and H_XIRR_X in XICS emulation
This adds the remaining two hypercalls defined by PAPR for manipulating
the XICS interrupt controller, H_IPOLL and H_XIRR_X. H_IPOLL returns
information about the priority and pending interrupts for a virtual
cpu, without changing any state. H_XIRR_X is like H_XIRR in that it
reads and acknowledges the highest-priority pending interrupt, but it
also returns the timestamp (timebase register value) from when the
interrupt was first received by the hypervisor. Currently we just
return the current time, since we don't do any software queueing of
virtual interrupts inside the XICS emulation code.
These hcalls are not currently used by Linux guests, but may be in
future.
Signed-off-by: Paul Mackerras <paulus@samba.org> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While returning from exception handling in case of PREEMPT enabled,
_TIF_NEED_RESCHED bit is checked in TI_FLAGS (thread_info flag) of current
task. Only if this bit is set, it should continue with the process of
calling preempt_schedule_irq() to schedule highest priority task if
available.
Current code assumes that r8 contains TI_FLAGS and check this for
_TIF_NEED_RESCHED, but as r8 is modified in the code which executes before
this check, r8 no longer contains the expected TI_FLAGS information.
As a result check for comparison with _TIF_NEED_RESCHED was failing even if
NEED_RESCHED bit is set in the current thread_info flag. Due to this,
preempt_schedule_irq() and in turn scheduler was not getting called even if
highest priority task is ready for execution.
So, store temporary results in r0 instead of r8 to prevent r8 from getting
modified as subsequent code is dependent on its value.
powerpc/mm: Always invalidate tlb on hpte invalidate and update
If a hash bucket gets full, we "evict" a more/less random entry from it.
When we do that we don't invalidate the TLB (hpte_remove) because we assume
the old translation is still technically "valid". This implies that when
we are invalidating or updating pte, even if HPTE entry is not valid
we should do a tlb invalidate.
Michael Neuling [Wed, 29 May 2013 19:34:27 +0000 (19:34 +0000)]
powerpc/pseries: Kill all prefetch streams on context switch
On context switch, we should have no prefetch streams leak from one
userspace process to another. This frees up prefetch resources for the
next process.
Based on patch from Milton Miller.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Maynard informed me that neither the oprofile kernel module nor oprofile
userspace has been updated to support that "legacy" oprofile module
interface for power8, which is indicated by "ppc64/power8." This results
in no samples. The solution is to default to the "timer" type, instead.
The raw entry also should be updated, as "ppc64/ibm-compat-v1" indicates
to oprofile userspace to use "compatibility events" which are obsolete
in ISA 2.07.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Sun, 26 May 2013 18:09:41 +0000 (18:09 +0000)]
powerpc/tm: Fix userspace stack corruption on signal delivery for active transactions
When in an active transaction that takes a signal, we need to be careful with
the stack. It's possible that the stack has moved back up after the tbegin.
The obvious case here is when the tbegin is called inside a function that
returns before a tend. In this case, the stack is part of the checkpointed
transactional memory state. If we write over this non transactionally or in
suspend, we are in trouble because if we get a tm abort, the program counter
and stack pointer will be back at the tbegin but our in memory stack won't be
valid anymore.
To avoid this, when taking a signal in an active transaction, we need to use
the stack pointer from the checkpointed state, rather than the speculated
state. This ensures that the signal context (written tm suspended) will be
written below the stack required for the rollback. The transaction is aborted
becuase of the treclaim, so any memory written between the tbegin and the
signal will be rolled back anyway.
For signals taken in non-TM or suspended mode, we use the
normal/non-checkpointed stack pointer.
Tested with 64 and 32 bit signals
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> # v3.9 Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>