Florian Mickler [Mon, 21 Mar 2011 18:33:41 +0000 (15:33 -0300)]
[media] a800: get rid of on-stack dma buffers
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Joonyoung Shim [Fri, 11 Mar 2011 06:54:46 +0000 (03:54 -0300)]
[media] radio-si470x: support seek and tune interrupt enable
Currently we use busy waiting to seek and tune, it can replace to
interrupt way. SI470X I2C driver supports interrupt way to week and tune
via this patch.
Jarod Wilson [Mon, 11 Apr 2011 21:49:24 +0000 (18:49 -0300)]
[media] tm6000: fix vbuf may be used uninitialized
In commit 8aff8ba95155df, most of the manipulations to vbuf inside
copy_streams were gated on if !dev->radio, but one place that touches
vbuf lays outside those gates -- a memcpy of vbuf isn't NULL. If we
initialize vbuf to NULL, that memcpy will never happen in the case where
we do have dev->radio, and otherwise, in the !dev->radio case, the code
behaves exactly like it did prior to 8aff8ba95155df.
While we're at it, also fix an incorrectly indented closing brace for
one of the sections touching vbuf that is conditional on !dev->radio.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Tue, 12 Apr 2011 16:38:27 +0000 (13:38 -0300)]
[media] rc/nuvoton-cir: enable CIR on w83667hg chip variant
Thanks to some excellent investigative work by Douglas Clowes, it was
uncovered that the older w83667hg Nuvoton chip functions with this
driver after actually enabling the CIR function via its multi-function
chip config register. The CIR and CIR wide-band sensor enable bits are
just in a different place on this hardware, so we only poke register
0x27 on 677 hardware now, and we poke register 0x2c on the 667 now.
Reported-by: Douglas Clowes <dclowes1@optusnet.com.au> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Tue, 12 Apr 2011 17:00:07 +0000 (14:00 -0300)]
[media] rc/nuvoton-cir: only warn about unknown chips
There are additional chip IDs that report a PNP ID of NTN0530, which we
were refusing to load on. Instead, lets just warn if we encounter an
unknown chip, as there's a chance it will work just fine.
Also, expand the list of known hardware to include both an earlier and a
later generation chip that this driver should function with. Douglas has
an older w83667hg variant, that with a touch more work, will be
supported by this driver, and Lutz has a newer w83677hg variant that
works without any further modifications to the driver.
Reported-by: Douglas Clowes <dclowes1@optusnet.com.au> Reported-by: Lutz Sammer <johns98@gmx.net> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Tue, 5 Apr 2011 21:42:30 +0000 (18:42 -0300)]
[media] rc: further key name standardization
Use the newly introduced KEY_IMAGES where appropriate, and standardize
on KEY_MEDIA for media center/application launcher button (such as the
Windows logo key on the Windows Media Center Ed. remotes).
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antonio Ospite [Thu, 7 Apr 2011 15:45:52 +0000 (12:45 -0300)]
[media] gspca - kinect: New subdriver for Microsoft Kinect
The Kinect sensor is a device used by Microsoft for its Kinect project,
which is a system for controller-less Human-Computer interaction
targeted for Xbox 360.
In the Kinect device, RGBD data is captured from two distinct sensors: a
regular RGB sensor and a monochrome sensor which, with the aid of a IR
structured light, captures what is finally exposed as a depth map; so
what we have is basically a Structured-light 3D scanner.
The Kinect gspca subdriver just supports the video stream for now,
exposing the output from the RGB sensor or the unprocessed output from
the monochrome sensor; it does not deal with the processed depth stream
yet, but it allows using the sensor as a Webcam or as an IR camera (an
external source of IR light might be needed for this use).
The low level implementation is based on code from the OpenKinect
project (http://openkinect.org).
Antonio Ospite [Thu, 7 Apr 2011 15:45:51 +0000 (12:45 -0300)]
[media] Add Y10B, a 10 bpp bit-packed greyscale format
Add a 10 bits per pixel greyscale format in a bit-packed array representation,
naming it Y10B. Such pixel format is supplied for instance by the Kinect
sensor device.
Andy Walls [Sun, 27 Mar 2011 03:43:30 +0000 (00:43 -0300)]
[media] cx18: Bump driver version, since a new class of HVR-1600 is properly supported
Make a user visible driver version change, for the inevitable user support
questions about why newer model HVR-1600's do not work with (older
versions of) the cx18 driver.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 27 Mar 2011 03:20:37 +0000 (00:20 -0300)]
[media] cx18: Make RF analog TV work for newer HVR-1600 models with silicon tuners
A previous changes which added the newer model HVR-1600's and DTV support for
them, neglected to add RF analog TV for them. Fix RF analog TV for the newer
HVR-1600's which have a worldwide analog tuner assembly with a TDA18271 tuner
and TDA8295 demodulator.
Thanks go to Jeff Campbell and Mike Bradley for reproting the problem, and
also to Mike Bradley for doing a lot of the legwork to figure out the tuner
reset GPIO line, the demodulator I2C address, and that the GPIOs have to be
reinitialized after a cardtype switch.
Reported-by: Jeff Campbell <jac1dlists@gmail.com> Tested-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are still lots of 80-columns warnings and a few errors
at some tables, but changing them would require more work and
with probably not much gain.
This file is big. It has 12000+ lines! Most of the defined stuff aren't
used anyware inside the driver, so we can just remove most of the lines
and still keep everything that have any interest for the driver.
If anyone ever need the other devices, it will be stored at git logs, so
it is easy to recover.
The diff result is impressive:
1 files changed, 1013 insertions(+), 12694 deletions(-)
rewrite drivers/media/dvb/frontends/drxd_map_firm.h (90%)
As a sideback effect, drxd driver will likely compile faster, and
checkpatch.pl can run on this file without taking (literally) hours.
The code cleanup was done using this small script:
$ for i in `perl -ne 'print "$1\n" if (m/define\s+([^\s+]+)/)' drxd_map_firm.h`; do if [ "`grep $i drivers/media/dvb/frontends/drxd*.[ch]`" != "" ] ; then echo $i; fi; done|sort|uniq >used_symbols
$ grep -f used_symbols drxd_map_firm.h >defines
And then deleting the old #define lines, replacing by "defines" file content.
[media] em28xx: fix GPIO problem with HVR-900R2 getting out of sync with drx-d
The em28xx bridge strobes the reset pin on the drx-d on every ts_ctrl call.
This results in the state of the chip getting out of the sync with the
state of the driver (and hence all tuning requests after the first one fail).
Make sure the drx-d is not being held in reset, but don't actually perform a
hardware reset on the chip.
The GPIO block has been split out from the other HVR-9x0 variants to reduce
the risk of regression, although in theory they would not have any issues
since none of those cases have the frontend driver managing any internal
state.
[media] drxd: provide ability to disable the i2c gate control function
If the tuner is not actually behind an i2c gate, using the i2c gate control
function can wedge the i2c bus. Provide the ability to control on a per-board
basis whether it should be used.
Problem was noticed on the HVR-900 R2, where it resulted in the first tuning
attempt succeeding, and then all subsequent attempts to access the xc3028
being treated as failures (including the call to sleep the tuner).
Provide the ability for the board configuration to specify whether to insert
the RS byte into the TS interconnect to the bridge, while not required for
the ngene in fact is required for the em28xx.
Ralph Metzler [Sun, 13 Mar 2011 04:44:33 +0000 (23:44 -0500)]
drx: add initial drx-d driver
These are the original drx-d sources, extracted from Ralph Metzler's GPL'd
ngene driver. No modifications/cleanup have yet been made. In fact, no
measures have been taken to see if the code even compiles.
[media] V4L: soc_camera_platform: add helper functions to manage device instances
Add helper inline functions to correctly manage dynamic allocation and
freeing of platform devices. This avoids the ugly code to nullify
device objects.
[media] xc5000: Improve it to work better with 6MHz-spaced channels
Brazil uses 6MHz-spaced channels. So, the nyquist filter for
DVB-C should be different, otherwise, inter-channel interference
may badly affect the device, and signal may not be properly decoded.
On my tests here, without this patch, sometimes channels are seen,
but, most of the time, PID filter returns with timeout.
Linus Torvalds [Wed, 18 May 2011 23:50:28 +0000 (16:50 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
configfs: Fix race between configfs_readdir() and configfs_d_iput()
configfs: Don't try to d_delete() negative dentries.
ocfs2/dlm: Target node death during resource migration leads to thread spin
ocfs2: Skip mount recovery for hard-ro mounts
ocfs2/cluster: Heartbeat mismatch message improved
ocfs2/cluster: Increase the live threshold for global heartbeat
ocfs2/dlm: Use negotiated o2dlm protocol version
ocfs2: skip existing hole when removing the last extent_rec in punching-hole codes.
ocfs2: Initialize data_ac (might be used uninitialized)
Linus Torvalds [Wed, 18 May 2011 20:25:57 +0000 (13:25 -0700)]
Merge branch 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
drivercore: revert addition of of_match to struct device
of: fix race when matching drivers
Grant Likely [Wed, 18 May 2011 17:19:24 +0000 (11:19 -0600)]
drivercore: revert addition of of_match to struct device
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Milton Miller [Wed, 18 May 2011 15:27:39 +0000 (10:27 -0500)]
of: fix race when matching drivers
If two drivers are probing devices at the same time, both will write
their match table result to the dev->of_match cache at the same time.
Only write the result if the device matches.
In a thread titled "SBus devices sometimes detected, sometimes not",
Meelis reported his SBus hme was not detected about 50% of the time.
From the debug suggested by Grant it was obvious another driver matched
some devices between the call to match the hme and the hme discovery
failling.
Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Milton Miller <miltonm@bga.com>
[grant.likely: modified to only call of_match_device() once] Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Linus Torvalds [Wed, 18 May 2011 13:49:02 +0000 (06:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't delay blk_run_queue_async
scsi: remove performance regression due to async queue run
blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
block: rescan partitions on invalidated devices on -ENOMEDIA too
cdrom: always check_disk_change() on open
block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers
Florian Fainelli [Fri, 13 May 2011 15:41:21 +0000 (17:41 +0200)]
MIPS: AR7: Fix GPIO register size for Titan variant.
The 'size' variable contains the correct register size for both AR7
and Titan, but we never used it to ioremap the correct register size.
This problem only shows up on Titan.
[ralf@linux-mips.org: Fixed the fix. The original patch as in patchwork
recognizes the problem correctly then fails to fix it ...]
This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Joel Becker [Wed, 18 May 2011 11:08:16 +0000 (04:08 -0700)]
configfs: Fix race between configfs_readdir() and configfs_d_iput()
configfs_readdir() will use the existing inode numbers of inodes in the
dcache, but it makes them up for attribute files that aren't currently
instantiated. There is a race where a closing attribute file can be
tearing down at the same time as configfs_readdir() is trying to get its
inode number.
We want to get the inode number of open attribute files, because they
should match while instantiated. We can't lock down the transition
where dentry->d_inode is set to NULL, so we just check for NULL there.
We can, however, ensure that an inode we find isn't iput() in
configfs_d_iput() until after we've accessed it.
Joel Becker [Tue, 22 Feb 2011 09:09:49 +0000 (01:09 -0800)]
configfs: Don't try to d_delete() negative dentries.
When configfs is faking mkdir() on its subsystem or default group
objects, it starts by adding a negative dentry. It then tries to
instantiate the group. If that should fail, it must clean up after
itself.
I was using d_delete() here, but configfs_attach_group() promises to
return an empty dentry on error. d_delete() explodes with the entry
dentry. Let's try d_drop() instead. The unhashing is what we want for
our dentry.
Shaohua Li [Wed, 18 May 2011 09:22:43 +0000 (11:22 +0200)]
block: don't delay blk_run_queue_async
Let's check a scenario:
1. blk_delay_queue(q, SCSI_QUEUE_DELAY);
2. blk_run_queue_async();
the second one will became a noop, because q->delay_work already has
WORK_STRUCT_PENDING_BIT set, so the delayed work will still run after
SCSI_QUEUE_DELAY. But blk_run_queue_async actually hopes the delayed
work runs immediately.
Fix this by doing a cancel on potentially pending delayed work
before queuing an immediate run of the workqueue.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Linus Torvalds [Wed, 18 May 2011 10:13:46 +0000 (03:13 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf evlist: Fix per thread mmap setup
perf tools: Honour the cpu list parameter when also monitoring a thread list
kprobes, x86: Disable irqs during optimized callback
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix cifsConvertToUCS() for the mapchars case
cifs: add fallback in is_path_accessible for old servers
os_dump_core() uses abort() to terminate UML in case of an fatal error.
glibc's abort() calls raise(SIGABRT) which makes use of tgkill().
tgkill() has no effect within UML's kernel threads because they are not
pthreads. As fallback abort() executes an invalid instruction to
terminate the process. Therefore UML gets killed by SIGSEGV and leaves a
ugly log entry in the host's kernel ring buffer.
To get rid of this we use our own abort routine.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ZONE_CONGESTED should be a state of global memory reclaim. If not, a busy
memcg sets this and give unnecessary throttoling in wait_iff_congested()
against memory recalim in other contexts. This makes system performance
bad.
I'll think about "memcg is congested!" flag is required or not, later.
But this fix is required first.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Acked-by: Ying Han <yinghan@google.com> Cc: Balbir Singh <balbir@in.ibm.com> Cc: Johannes Weiner <jweiner@redhat.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix switch initialization to ensure that all switches have default routing
disabled. This guarantees that no unexpected RapidIO packets arrive to
the default port set by reset and there is no default routing destination
until it is properly configured by software.
This update also unifies handling of unmapped destinations by tsi57x, IDT
Gen1 and IDT Gen2 switches.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: <stable@kernel.org> [2.6.37+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Tue, 17 May 2011 19:28:21 +0000 (15:28 -0400)]
cifs: fix cifsConvertToUCS() for the mapchars case
As Metze pointed out, commit 84cdf74e broke mapchars option:
Commit "cifs: fix unaligned accesses in cifsConvertToUCS"
(84cdf74e8096a10dd6acbb870dd404b92f07a756) does multiple steps
in just one commit (moving the function and changing it without
testing).
put_unaligned_le16(temp, &target[j]); is never called for any
codepoint the goes via the 'default' switch statement. As a result
we put just zero (or maybe uninitialized) bytes into the target
buffer.
His proposed patch looks correct, but doesn't apply to the current head
of the tree. This patch should also fix it.
Cc: <stable@kernel.org> # .38.x: 581ade4: cifs: clean up various nits in unicode routines (try #2) Reported-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Tue, 17 May 2011 10:40:30 +0000 (06:40 -0400)]
cifs: add fallback in is_path_accessible for old servers
The is_path_accessible check uses a QPathInfo call, which isn't
supported by ancient win9x era servers. Fall back to an older
SMBQueryInfo call if it fails with the magic error codes.
Cc: stable@kernel.org Reported-and-Tested-by: Sandro Bonazzola <sandro.bonazzola@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Borislav Petkov [Tue, 17 May 2011 12:55:19 +0000 (14:55 +0200)]
x86, AMD: Fix ARAT feature setting again
Trying to enable the local APIC timer on early K8 revisions
uncovers a number of other issues with it, in conjunction with
the C1E enter path on AMD. Fixing those causes much more churn
and troubles than the benefit of using that timer brings so
don't enable it on K8 at all, falling back to the original
functionality the kernel had wrt to that.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com> Cc: Boris Ostrovsky <Boris.Ostrovsky@amd.com> Cc: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Greg Kroah-Hartman <greg@kroah.com> Cc: Hans Rosenfeld <hans.rosenfeld@amd.com> Cc: Nick Bowler <nbowler@elliptictech.com> Cc: Joerg-Volker-Peetz <jvpeetz@web.de> Signed-off-by: Borislav Petkov <borislav.petkov@amd.com> Link: http://lkml.kernel.org/r/1305636919-31165-3-git-send-email-bp@amd64.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
Moving the lower endpoint of the Erratum 400 check to accomodate
earlier K8 revisions (A-E) opens a can of worms which is simply
not worth to fix properly by tweaking the errata checking
framework:
* missing IntPenging MSR on revisions < CG cause #GP:
Jens Axboe [Tue, 17 May 2011 09:04:44 +0000 (11:04 +0200)]
scsi: remove performance regression due to async queue run
Commit c21e6beb removed our queue request_fn re-enter
protection, and defaulted to always running the queues from
kblockd to be safe. This was a known potential slow down,
but should be safe.
Unfortunately this is causing big performance regressions for
some, so we need to improve this logic. Looking into the details
of the re-enter, the real issue is on requeue of requests.
Requeue of requests upon seeing a BUSY condition from the device
ends up re-running the queue, causing traces like this:
potentially causing the issue we want to avoid. So special
case the requeue re-run of the queue, but improve it to offload
the entire run of local queue and starved queue from a single
workqueue callback. This is a lot better than potentially
kicking off a workqueue run for each device seen.
This also fixes the issue of the local device going into recursion,
since the above mentioned commit never moved that queue run out
of line.
Linus Torvalds [Tue, 17 May 2011 01:36:47 +0000 (18:36 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
Revert "mmc: fix a race between card-detect rescan and clock-gate work instances"
projects / linux-beck.git / log