Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is quite similar to b39fe41f481d20c201012e4483e76c203802dda7
though said registers are not even documented as 64-bit registers
- as opposed to the initial TxDescStartAddress ones - but as single
bytes which must be combined into 32 bits at the MMIO read/write
level before being merged into a 64 bit logical entity.
Credits go to Ben Hutchings <ben@decadent.org.uk> for the MAR
registers (aka "multicast is broken for ages on ARM) and to
Timo Teräs <timo.teras@iki.fi> for the MAC registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
r8169 needs certain writes to be visible to other CPUs or the NIC before
touching the hardware, but was using smp_wmb() which is only required to
order cacheable memory access. Switch to wmb() which is required to
order both cacheable and non-cacheable memory.
Noticed by Catalin Marinas and Paul Mackerras.
Signed-off-by: David Dillow <dave@thedillows.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bypassing of this test is a leftover from 2.4 vintage
kernels, and is no longer appropriate, or even used by KGDB.
Currently KGDB uses probe_kernel_write() for all access to
memory via the KGDB core, so it can simply be deleted.
This fixes CVE-2010-1446.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: Paul Mackerras <paulus@samba.org> CC: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Wufei <fei.wu@windriver.com> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix off by one error in the queue size check of p54_tx_qos_accounting_alloc()
Coverity CID: 13314
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resizing the filesystem would result in an diAllocExt error in some
instances because changes in bmp->db_agsize would not get noticed if
goto extendBmap was called.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Cc: jfs-discussion@lists.sourceforge.net Cc: linux-kernel@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
creds_are_invalid() reads both cred->usage and cred->subscribers and then
compares them to make sure the number of processes subscribed to a cred struct
never exceeds the refcount of that cred struct.
The problem is that this can cause a race with both copy_creds() and
exit_creds() as the two counters, whilst they are of atomic_t type, are only
atomic with respect to themselves, and not atomic with respect to each other.
This means that if creds_are_invalid() can read the values on one CPU whilst
they're being modified on another CPU, and so can observe an evolving state in
which the subscribers count now is greater than the usage count a moment
before.
Switching the order in which the counts are read cannot help, so the thing to
do is to remove that particular check.
I had considered rechecking the values to see if they're in flux if the test
fails, but I can't guarantee they won't appear the same, even if they've
changed several times in the meantime.
Note that this can only happen if CONFIG_DEBUG_CREDENTIALS is enabled.
The problem is only likely to occur with multithreaded programs, and can be
tested by the tst-eintr1 program from glibc's "make check". The symptoms look
like:
The unpack routine fails to handle the decompress_method() returning
unrecognised decompressor (compress_name == NULL). This results in the
routine looping eventually oopsing on an out of bounds memory access.
Note this bug is usually hidden, only triggering on trailing junk after
one or more correct compressed blocks. The case of the compressed archive
being complete junk is (by accident?) caught by the if (state != Reset)
check because state is initialised to Start, but not updated due to the
decompressor not having been called. Obviously if the junk is trailing a
correctly decompressed buffer, state == Reset from the previous call to
the decompressor.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk> Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ext4_fiemap() rounds the length of the requested range down to
blocksize, which is is not the true number of blocks that cover the
requested region. This problem is especially impressive if the user
requests only the first byte of a file: not a single extent will be
reported.
We fix this by calculating the last block of the region and then
subtract to find the number of blocks in the extents.
Most drives from Seagate, Hitachi, and possibly other brands,
do not allow LBA28 access to sector number 0x0fffffff (2^28 - 1).
So instead use LBA48 for such accesses.
This bug could bite a lot of systems, especially when the user has
taken care to align partitions to 4KB boundaries. On misaligned systems,
it is less likely to be encountered, since a 4KB read would end at
0x10000000 rather than at 0x0fffffff.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the firmware puts a device back into D0 state at resume time, we'll
update its state in resume_noirq and thus skip the platform resume code.
Calling that code twice should be safe and we ought to avoid getting to
that point anyway, so remove the check and also allow the platform pci
code to be called for D0.
Fixes USB not being powered after resume on recent Lenovo machines.
Acked-by: Alex Chiang <achiang@canonical.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/549267
The OR verified that using the olpc-xo-1_5 model quirk allows the
headphones to be audible when inserted into the jack. Capture was
also verified to work correctly.
Reported-by: Richard Gagne Tested-by: Richard Gagne Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/573284
The OR verified that using the olpc-xo-1_5 model quirk allows the
headphones to be audible when inserted into the jack. Capture was
also verified to work correctly.
Reported-by: Andy Couldrake <acouldrake@googlemail.com> Tested-by: Andy Couldrake <acouldrake@googlemail.com> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/541802
The OR's hardware distorts at PCM 100% because it does not correspond to
0 dB. Fix this in patch_cxt5045() for all Packard Bell models.
Reported-by: Valombre Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ignore spurious HV interrupts during suspend / resume, this avoids
mistaking them for a mute button press. This is not very pretty but
it seems the only way to fix the master volume control gets muted
after suspend issue I'm seeing. Note that the es1968 driver is doing
exactly the same.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this quirk sound stops working after suspend resume. With this quirk,
one still needs to manually unmute the master volume control after a suspend /
/ resume cycle. That is fixed in another patch in this set.
Note that this patch was submitted to the alsa bug tracker a long time ago:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4319
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/567494
The OR has verified that the existing model quirk, ALC880_UNIWILL,
is insufficient for audible playback and capture by default. Instead,
the ALC880_F1734 model quirk needs to be used.
This change is necessary for both 2.6.32.11 and 2.6.33.2.
BugLink: https://launchpad.net/bugs/568600
The OR has verified that the dell-m6 model quirk is necessary for audio
to be audible by default on the Dell Studio XPS 1645.
This change is necessary for 2.6.32.11 and 2.6.33.2 alike.
Reported-by: Andy Ross <andy@plausible.org> Tested-by: Andy Ross <andy@plausible.org> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/553002
The OR has verified that the dell-m6 model quirk is necessary for audio
to be audible by default on the Dell Studio XPS 1645.
This change is necessary for 2.6.32.11 and 2.6.33.2 alike.
Reported-by: Robert Chambers Tested-by: Robert Chambers Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/459083
The OR has verified with 2.6.32.11 and the latest alsa-driver stable
daily snapshot that position_fix=1 is necessary for the external mic
to work and for PulseAudio not to crash constantly.
This patch is necessary also for 2.6.32.11 and 2.6.33.2.
Reported-by: <imwithid@yahoo.com> Tested-by: <imwithid@yahoo.com> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One side effect of it is that num_k8_northbridges
is not initialized anymore if not explicitly
called. This resulted in uninitialized pointers in
<arch/x86/kernel/cpu/intel_cacheinfo.c:amd_calc_l3_indices()>,
for example, which uses the num_k8_northbridges thing through
node_to_k8_nb_misc().
Fix that through an initcall that runs right after the PCI
subsystem and does all the scanning. Then, remove initialization
in gart_iommu_init() which is a rootfs_initcall and we're
running before that.
What is more, since num_k8_northbridges is being used in other
places beside GART IOMMU, include it whenever we add AMD CPU
support. The previous dependency chain in kconfig contained
K8_NB depends on AGP_AMD64|GART_IOMMU
which was clearly incorrect. The more natural way in terms of
hardware dependency should be
AGP_AMD64|GART_IOMMU depends on K8_NB depends on CPU_SUP_AMD &&
PCI. Make it so Number One!
Upstream PV guests fail to boot because of a NULL pointer in
irq_force_complete_move(). It is possible that xen guests have
irq_desc->chip_data = NULL.
Test for NULL chip_data pointer before attempting to complete an irq move.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
LKML-Reference: <20100427152434.16193.49104.sendpatchset@prarit.bos.redhat.com> Acked-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"If software clears the PS (page size) bit in a present PDE (page
directory entry), that will cause linear addresses mapped through this
PDE to use 4-KByte pages instead of using a large page after old TLB
entries are invalidated. Due to this erratum, if a code fetch uses
this PDE before the TLB entry for the large page is invalidated then
it may fetch from a different physical address than specified by
either the old large page translation or the new 4-KByte page
translation. This erratum may also cause speculative code fetches from
incorrect addresses."
Where as commit 211b3d03c7400f48a781977a50104c9d12f4e229 seems to
workaround errata AAH41 (mixed 4K TLBs) it reduces the window of
opportunity for the bug to occur and does not totally remove it. This
patch disables mixed 4K/4MB page tables totally avoiding the page
splitting and not tripping this processor issue.
This is based on an original patch by Colin King.
Originally-by: Colin Ian King <colin.king@canonical.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <1269271251-19775-1-git-send-email-colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we do a thread switch, we clear the outgoing FS/GS base if the
corresponding selector is nonzero. This is taken by __switch_to() as
an entry invariant; it does not verify that it is true on entry.
However, copy_thread() doesn't enforce this constraint, which can
result in inconsistent results after fork().
Make copy_thread() match the behavior of __switch_to().
Reported-and-tested-by: Samuel Thibault <samuel.thibault@inria.fr> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4BD1E061.8030605@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hans de Goede identified a bug in p54p_check_tx_ring:
there are two ring indices. 1 => tx data and 3 => tx management.
But the old code had a constant "1" and this resulted in spurious
dma unmapping failures.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623 Bug-Identified-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use correct bit positions in DM_SHARED_CTRL register for writes.
Michael Planes recently encountered a 'KY-RS9600 USB-LAN converter', which
came with a driver CD containing a Linux driver. This driver turns out to
be a copy of dm9601.c with symbols renamed and my copyright stripped.
That aside, it did contain 1 functional change in dm_write_shared_word(),
and after checking the datasheet the original value was indeed wrong
(read versus write bits).
On Michaels HW, this change bumps receive speed from ~30KB/s to ~900KB/s.
On other devices the difference is less spectacular, but still significant
(~30%).
Reported-by: Michael Planes <michael.planes@free.fr> Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It changes user-visible sysfs interfaces, and breaks some existing user
space applications which apparently rely on the fact that the output
does not contain the "0x" prefix.
blk_rq_timed_out_timer() relied on blk_add_timer() never returning a
timer value of zero, but commit 7838c15b8dd18e78a523513749e5b54bda07b0cb
removed the code that bumped this value when it was zero.
Therefore when jiffies is near wrap we could get unlucky & not set the
timeout value correctly.
This patch uses a flag to indicate that the timeout value was set and so
handles jiffies wrap correctly, and it keeps all the logic in one
function so should be easier to maintain in the future.
The raid6 recovery code should immediately drop back to the optimized
synchronous path when a p+q dma resource is not available. Otherwise we
run the non-optimized/multi-pass async code in sync mode.
Verified with raid6test (NDISKS=255)
Applies to kernels >= 2.6.32.
Acked-by: NeilBrown <neilb@suse.de> Reported-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some FSC hardware monitoring chips (Syleus at least) doesn't like
quick writes we typically use to probe for I2C chips. Use a regular
byte read instead for the address they live at (0x73). These are the
only known chips living at this address on PC systems.
For clarity, this fix should not be needed for kernels 2.6.30 and
later, as we started instantiating the hwmon devices explicitly based
on DMI data. Still, this fix is valuable in the following two cases:
* Support for recent FSC chips on older kernels. The DMI-based device
instantiation is more difficult to backport than the device support
itself.
* Case where the DMI-based device instantiation fails, whatever the
reason. We fall back to probing in that case, so it should work.
This fixes kernel bug #15634:
https://bugzilla.kernel.org/show_bug.cgi?id=15634
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the HyperV network device use the same naming scheme as
other virtual drivers (Xen, KVM). In an ideal world, userspace tools
would not care what the name is, but some users and applications do
care. Vyatta CLI is one of the tools that does depend on what the name
is.
NFSv4 mounts ignore the rsize and wsize mount options, and always use
the default transfer size for both. This seems to be because all
NFSv4 mounts are now cloned, and the cloning logic doesn't copy the
rsize and wsize settings from the parent nfs_server.
I tested Fedora's 2.6.32.11-99 and it seems to have this problem as
well, so I'm guessing that .33, .32, and perhaps older kernels have
this issue as well.
If dentry found stale happens to be a root of disconnected tree, we
can't d_drop() it; its d_hash is actually part of s_anon and d_drop()
would simply hide it from shrink_dcache_for_umount(), leading to
all sorts of fun, including busy inodes on umount and oopsen after
that.
Bug had been there since at least 2006 (commit c636eb already has it),
so it's definitely -stable fodder.
In reflink we update the id info on the disk but forgot to update
the corresponding information in the VFS inode. Update them
accordingly when we want to preserve the attributes.
Reported-by: Jeff Liu <jeff.liu@oracle.com> Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For periodic endpoints, we must let the xHCI hardware know the maximum
payload an endpoint can transfer in one service interval. The xHCI
specification refers to this as the Maximum Endpoint Service Interval Time
Payload (Max ESIT Payload). This is used by the hardware for bandwidth
management and scheduling of packets.
For SuperSpeed endpoints, the maximum is calculated by multiplying the max
packet size by the number of bursts and the number of opportunities to
transfer within a service interval (the Mult field of the SuperSpeed
Endpoint companion descriptor). Devices advertise this in the
wBytesPerInterval field of their SuperSpeed Endpoint Companion Descriptor.
For high speed devices, this is taken by multiplying the max packet size by the
"number of additional transaction opportunities per microframe" (the high
bits of the wMaxPacketSize field in the endpoint descriptor).
For FS/LS devices, this is just the max packet size.
The other thing we must set in the endpoint context is the Average TRB
Length. This is supposed to be the average of the total bytes in the
transfer descriptor (TD), divided by the number of transfer request blocks
(TRBs) it takes to describe the TD. This gives the host controller an
indication of whether the driver will be enqueuing a scatter gather list
with many entries comprised of small buffers, or one contiguous buffer.
It also takes into account the number of extra TRBs you need for every TD.
This includes No-op TRBs and Link TRBs used to link ring segments
together. Some drivers may choose to chain an Event Data TRB on the end
of every TD, thus increasing the average number of TRBs per TD. The Linux
xHCI driver does not use Event Data TRBs.
In theory, if there was an API to allow drivers to state what their
bandwidth requirements are, we could set this field accurately. For now,
we set it to the same number as the Max ESIT payload.
The Average TRB Length should also be set for bulk and control endpoints,
but I have no idea how to guess what it should be.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A SuperSpeed interrupt or isochronous endpoint can define the number of
"burst transactions" it can handle in a service interval. This is
indicated by the "Mult" bits in the bmAttributes of the SuperSpeed
Endpoint Companion Descriptor. For example, if it has a max packet size
of 1024, a max burst of 11, and a mult of 3, the host may send 33
1024-byte packets in one service interval.
We must tell the xHCI host controller the number of multiple service
opportunities (mults) the device can handle when the endpoint is
installed. We do that by setting the Mult field of the Endpoint Context
before a configure endpoint command is sent down. The Mult field is
invalid for control or bulk SuperSpeed endpoints.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1371) fixes a small bug in ohci-hcd. The HCD already
knows how many ports the controller has; there's no need to go looking
at the root hub's usb_device structure to find out. Especially since
the root hub's maxchild value is set correctly only while the root hub
is bound to the hub driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1372) fixes a bug in the routine that chooses the
default configuration to install when a new USB device is detected.
The algorithm is supposed to look for a config whose first interface
is for a non-vendor-specific class. But the way it's currently
written, it will also accept a config with no interfaces at all, which
is not very useful. (Believe it or not, such things do exist.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Andrew Victor <avictor.za@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a typo here. We should be testing "*dentry" which was just
assigned instead of "dentry". This could result in dereferencing an
ERR_PTR inside either usbfs_mkdir() or usbfs_create().
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While looping over the interfaces, if usb_hcd_alloc_bandwidth() fails it calls
hcd->driver->reset_bandwidth(), so there was no need to reinstate the interface
again.
If no break occurred, the index equals config->desc.bNumInterfaces. A
subsequent usb_control_msg() failure resulted in a read from
config->interface[config->desc.bNumInterfaces] at label reset_old_alts.
In either case the last interface should be skipped.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1363b) changes the way USB remote wakeup is handled
during system sleeps. It won't be enabled unless an interface driver
specifically needs it. Also, it won't be enabled during the FREEZE or
QUIESCE phases of hibernation, when the system doesn't respond to
wakeup events anyway.
This will fix problems people have reported with certain USB webcams
that generate wakeup requests when they shouldn't, and as a result
cause system suspends to fail. See
When detaching a port from the client side (usbip --detach 0),
the event thread, on the server side, is going to deadlock.
The "eh" server thread is getting USBIP_EH_RESET event and calls:
-> stub_device_reset() -> usb_reset_device()
the USB framework is then calling back _in the same "eh" thread_ :
-> stub_disconnect() -> usbip_stop_eh() -> wait_for_completion()
the "eh" thread is being asleep forever, waiting for its own completion.
This patch checks if "eh" is the current thread, in usbip_stop_eh().
Signed-off-by: Eric Lescouet <eric@lescouet.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver needs specific PHY and board support code for each SFC4000
board; there is no point trying to continue if it is missing.
Currently unsupported boards can trigger an 'oops'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code would wait indefinitely if MAC stats DMA failed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The request_key() system call and request_key_and_link() should make a
link from an existing key to the destination keyring (if supplied), not
just from a new key to the destination keyring.
This can be tested by:
ring=`keyctl newring fred @s`
keyctl request2 user debug:a a
keyctl request user debug:a $ring
keyctl list $ring
If it says:
keyring is empty
then it didn't work. If it shows something like:
1 key in keyring: 1070462727: --alswrv 0 0 user: debug:a
then it did.
request_key() system call is meant to recursively search all your keyrings for
the key you desire, and, optionally, if it doesn't exist, call out to userspace
to create one for you.
If request_key() finds or creates a key, it should, optionally, create a link
to that key from the destination keyring specified.
Therefore, if, after a successful call to request_key() with a desination
keyring specified, you see the destination keyring empty, the code didn't work
correctly.
If you see the found key in the keyring, then it did - which is what the patch
is required for.
Signed-off-by: David Howells <dhowells@redhat.com> Cc: James Morris <jmorris@namei.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When read_buf is called to move over to the next page in the pagelist
of an NFSv4 request, it sets argp->end to essentially a random
number, certainly not an address within the page which argp->p now
points to. So subsequent calls to READ_BUF will think there is much
more than a page of spare space (the cast to u32 ensures an unsigned
comparison) so we can expect to fall off the end of the second
page.
We never encountered thsi in testing because typically the only
operations which use more than two pages are write-like operations,
which have their own decoding logic. Something like a getattr after a
write may cross a page boundary, but it would be very unusual for it to
cross another boundary after that.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 48b32a3553a54740d236b79a90f20147a25875e3 ("reiserfs: use generic
xattr handlers") introduced a problem that causes corruption when extended
attributes are replaced with a smaller value.
The issue is that the reiserfs_setattr to shrink the xattr file was moved
from before the write to after the write.
The root issue has always been in the reiserfs xattr code, but was papered
over by the fact that in the shrink case, the file would just be expanded
again while the xattr was written.
The end result is that the last 8 bytes of xattr data are lost.
Commit 677c9b2e393a0cd203bd54e9c18b012b2c73305a ("reiserfs: remove
privroot hiding in lookup") removed the magic from the lookup code to hide
the .reiserfs_priv directory since it was getting loaded at mount-time
instead. The intent was that the entry would be hidden from the user via
a poisoned d_compare, but this was faulty.
This introduced a security issue where unprivileged users could access and
modify extended attributes or ACLs belonging to other users, including
root.
This patch resolves the issue by properly hiding .reiserfs_priv. This was
the intent of the xattr poisoning code, but it appears to have never
worked as expected. This is fixed by using d_revalidate instead of
d_compare.
This patch makes -oexpose_privroot a no-op. I'm fine leaving it this way.
The effort involved in working out the corner cases wrt permissions and
caching outweigh the benefit of the feature.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Acked-by: Edward Shishkin <edward.shishkin@gmail.com> Reported-by: Matt McCutchen <matt@mattmccutchen.net> Tested-by: Matt McCutchen <matt@mattmccutchen.net> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a futex key happens to be located within a huge page mapped
MAP_PRIVATE, get_futex_key() can go into an infinite loop waiting for a
page->mapping that will never exist.
See https://bugzilla.redhat.com/show_bug.cgi?id=552257 for more details
about the problem.
This patch makes page->mapping a poisoned value that includes
PAGE_MAPPING_ANON mapped MAP_PRIVATE. This is enough for futex to
continue but because of PAGE_MAPPING_ANON, the poisoned value is not
dereferenced or used by futex. No other part of the VM should be
dereferencing the page->mapping of a hugetlbfs page as its page cache is
not on the LRU.
This patch fixes the problem with the test case described in the bugzilla.
[akpm@linux-foundation.org: mel cant spel] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Darren Hart <darren@dvhart.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the addba timer expires but has no work to do,
it should not affect the state machine. If it does,
TX will not see the successfully established and we
can also crash trying to re-establish the session.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a signal is pending (task being killed by sigkill)
__mem_cgroup_try_charge will write NULL into &mem, and css_put will oops
on null pointer dereference.
Pid: 5299, comm: largepages Tainted: G W 2.6.34-rc3 #3 Penryn1600SLI-110dB/To Be Filled By O.E.M.
RIP: 0010:[<ffffffff810fc6cc>] [<ffffffff810fc6cc>] mem_cgroup_prepare_migration+0x7c/0xc0
Fix regression caused by commit 507e2fbaaacb6f164b4125b87c5002f95143174b
("w1: w1 temp calculation overflow fix") whereby negative temperatures for
the DS18B20 are not converted properly.
When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees. These are both well within the -55 - +125 degree
range for the sensor.
Current code is definitely crap: Largest pitch allowed spills into
the TILING_Y bit of the fence registers ... :(
I've rewritten the limits check under the assumption that 3rd gen hw
has a 3d pitch limit of 8kb (like 2nd gen). This is supported by an
otherwise totally misleading XXX comment.
This bug mostly resulted in tiling-corrupted pixmaps because the kernel
allowed too wide buffers to be tiled. Bug brought to the light by the
xf86-video-intel 2.11 release because that unconditionally enabled
tiling for pixmaps, relying on the kernel to check things. Tiling for
the framebuffer was not affected because the ddx does some additional
checks there ensure the buffer is within hw-limits.
v2: Instead of computing the value that would be written into the
hw fence registers and then checking the limits simply check whether
the stride is above the 8kb limit. To better document the hw, add
some WARN_ONs in i915_write_fence_reg like I've done for the i830
case (using the right limits).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=27449 Tested-by: Alexander Lam <lambchop468@gmail.com> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[needed for stable as it's just a bunch of macros that other drm patches
need, it changes no code functionality besides adding support for a new
device type. - gregkh]
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1369) fixes a problem in ehci-hcd. Some controllers
occasionally run into trouble when the driver reclaims siTDs too
quickly. This can happen while streaming audio; it causes the
controller to crash.
The patch changes siTD reclamation to work the same way as iTD
reclamation: Completed siTDs are stored on a list and not reused until
at least one frame has passed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Nate Case <ncase@xes-inc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Brandon Philips noted that I had a spacing issue in my printk for the
last r8169 patch that made it quite ugly. Fix that up and add the PFX
macro to it as well so it looks like the other r8169 printks
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we boot into a crash-kernel the gart might still be
enabled and its caches might be dirty. This can result in
undefined behavior later. Fix it by explicitly disabling the
gart hardware before initialization and flushing the caches
after enablement.
This patch increases the current hardcoded limit of NR_IOBUS_DEVS
from 6 to 200. We are hitting this limit when creating a guest with more
than 1 virtio-net device using vhost-net backend. Each virtio-net
device requires 2 such devices to service notifications from rx/tx queues.
- calculate zapped page number properly in mmu_zap_unsync_children()
- calculate freeed page number properly kvm_mmu_change_mmu_pages()
- if zapped children page it shoud restart hlist walking
Currently we set eflags.vm unconditionally when entering real mode emulation
through virtual-8086 mode, and clear it unconditionally when we enter protected
mode. The means that the following sequence
Ends up with rflags.vm clear due to KVM_SET_SREGS triggering enter_pmode().
Fix by shadowing rflags.vm (and rflags.iopl) correctly while in real mode:
reads and writes to those bits access a shadow register instead of the actual
register.
There is a quirk for AMD K8 CPUs in many Linux kernels (see
arch/x86/kernel/cpu/mcheck/mce.c:__mcheck_cpu_apply_quirks()) that
clears bit 10 in that MCE related MSR. KVM can only cope with all
zeros or all ones, so it will inject a #GP into the guest, which
will let it panic.
So lets add a quirk to the quirk and ignore this single cleared bit.
This fixes -cpu kvm64 on all machines and -cpu host on K8 machines
with some guest Linux kernels.
Signed-off-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We intercept #BP while in guest debugging mode. As VM exits due to
intercepted exceptions do not necessarily come with valid
idt_vectoring, we have to update event_exit_inst_len explicitly in such
cases. At least in the absence of migration, this ensures that
re-injections of #BP will find and use the correct instruction length.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Compiling 2.6.33 with SMP enabled and HOTPLUG_CPU disabled gives me the
following link errors:
LD init/built-in.o
LD .tmp_vmlinux1
arch/powerpc/platforms/built-in.o: In function `.smp_xics_setup_cpu':
smp.c:(.devinit.text+0x88): undefined reference to `.set_cpu_current_state'
smp.c:(.devinit.text+0x94): undefined reference to `.set_default_offline_state'
arch/powerpc/platforms/built-in.o: In function `.smp_pSeries_kick_cpu':
smp.c:(.devinit.text+0x13c): undefined reference to `.set_preferred_offline_state'
smp.c:(.devinit.text+0x148): undefined reference to `.get_cpu_current_state'
smp.c:(.devinit.text+0x1a8): undefined reference to `.get_cpu_current_state'
make: *** [.tmp_vmlinux1] Error 1
The following change fixes that for me and seems to work as expected.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a component device has a merge_bvec_fn then as we never call it
we must ensure we never need to. Currently this is done by setting
max_sector to 1 PAGE, however this does not stop a bio being created
with several sub-page iovecs that would violate the merge_bvec_fn.
So instead set max_phys_segments to 1 and set the segment boundary to the
same as a page boundary to ensure there is only ever one single-page
segment of IO requested at a time.
This can particularly be an issue when 'xen' is used as it is
known to submit multiple small buffers in a single bio.
It causes a NULL pointer exception on some configurations when CONFIG_TRACING is
enabled on 2.6.33. This patch fixes the problem (acknowledged by Randy who
reported the bug).
It did not appear to hurt previously because most of the accesses were done
through local_inc, which probably obfuscated the access enough that no compiler
optimizations were done. But with local_read() done when CONFIG_TRACING is
active, this becomes a problem. Non-CONFIG_TRACING is probably affected as well
(module.c contains local_set and local_read that use __module_ref_addr()), but I
guess nobody noticed because we've been lucky enough that the compiler did not
generate the inappropriate optimization pattern there.
This patch should be queued for the 2.6.29.x through 2.6.33.x stable branches.
(tested on 2.6.33.1 x86_64)
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Tested-by: Randy Dunlap <randy.dunlap@oracle.com> CC: Eric Dumazet <dada1@cosmosbay.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Peter Zijlstra <a.p.zijlstra@chello.nl> CC: Tejun Heo <tj@kernel.org> CC: Ingo Molnar <mingo@elte.hu> CC: Andrew Morton <akpm@linux-foundation.org> CC: Linus Torvalds <torvalds@linux-foundation.org> CC: Greg Kroah-Hartman <gregkh@suse.de> CC: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
But it's really just moving the code around. But it's enough to say that the
problems appeared before Jul 19 01:48:54 2007, which brings us back to 2.6.23.
It should be applied to stable 2.6.23.x to 2.6.33.x (or whichever of these
stable branches are still maintained).
(tested on 2.6.33.1 x86_64)
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> CC: Randy Dunlap <randy.dunlap@oracle.com> CC: Eric Dumazet <dada1@cosmosbay.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Peter Zijlstra <a.p.zijlstra@chello.nl> CC: Tejun Heo <tj@kernel.org> CC: Ingo Molnar <mingo@elte.hu> CC: Andrew Morton <akpm@linux-foundation.org> CC: Linus Torvalds <torvalds@linux-foundation.org> CC: Greg Kroah-Hartman <gregkh@suse.de> CC: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
access_bit_width field is u8 in ACPICA, thus 256 value written to it
becomes 0, causing divide by zero later.
Proper fix would be to remove access_bit_width at all, just because
we already have access_byte_width, which is access_bit_width / 8.
Limit access width to 64 bit for now.
https://bugzilla.kernel.org/show_bug.cgi?id=15749
fixes regression caused by the fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=14667
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xfssyncd processes a queue of work by detaching the queue and
then iterating over all the work items. It then sleeps for a
time period or until new work comes in. If new work is queued
while xfssyncd is actively processing the detached work queue,
it will not process that new work until after a sleep timeout
or the next work event queued wakes it.
Fix this by checking the work queue again before going to sleep.
Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The radix-tree code requires it's users to serialize tag updates
against other updates to the tree. While XFS protects tag updates
against each other it does not serialize them against updates of the
tree contents, which can lead to tag corruption. Fix the inode
cache to always take pag_ici_lock in exclusive mode when updating
radix tree tags.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Patrick Schreurs <patrick@news-service.com> Tested-by: Patrick Schreurs <patrick@news-service.com> Signed-off-by: Alex Elder <aelder@sgi.com> Cc: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The introduction of barriers to loop devices has created a new IO
order completion dependency that XFS does not handle. The loop
device implements barriers using fsync and so turns a log IO in the
XFS filesystem on the loop device into a data IO in the backing
filesystem. That is, the completion of log IOs in the loop
filesystem are now dependent on completion of data IO in the backing
filesystem.
This can cause deadlocks when a flush daemon issues a log force with
an inode locked because the IO completion of IO on the inode is
blocked by the inode lock. This in turn prevents further data IO
completion from occuring on all XFS filesystems on that CPU (due to
the shared nature of the completion queues). This then prevents the
log IO from completing because the log is waiting for data IO
completion as well.
The fix for this new completion order dependency issue is to make
the IO completion inode locking non-blocking. If the inode lock
can't be grabbed, simply requeue the IO completion back to the work
queue so that it can be processed later. This prevents the
completion queue from being blocked and allows data IO completion on
other inodes to proceed, hence avoiding completion order dependent
deadlocks.
Signed-off-by: Dave Chinner <david@fromorbit.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
perf_events, x86: Implement Intel Westmere support
The new Intel documentation includes Westmere arch specific
event maps that are significantly different from the Nehalem
ones. Add support for this generation.
Found the CPUID model numbers on wikipedia.
Also ammend some Nehalem constraints, spotted those when looking
for the differences between Nehalem and Westmere.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <20100127221122.151865645@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
perf, x86: Enable Nehalem-EX support
According to Intel Software Devel Manual Volume 3B, the
Nehalem-EX PMU is just like regular Nehalem (except for the
uncore support, which is completely different).
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Lin Ming <ming.m.lin@intel.com>
LKML-Reference: <alpine.DEB.2.00.1004060956580.1417@cl320.eecs.utk.edu> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Youquan Song <youquan.song@linux.intel.com>