Steve Hodgson [Sat, 28 Nov 2009 05:34:29 +0000 (05:34 +0000)]
sfc: QT202x: Reset before reading PHY id
Reading standard registers on the QT2025C before its firmware has
booted may cause the boot process to fail. Therefore, follow the
recommended reset sequence before reading its id registers. Either
order works for the QT2022C2, so don't differentiate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Hodgson [Sat, 28 Nov 2009 05:34:05 +0000 (05:34 +0000)]
sfc: Simplify PHY polling
Falcon can generate events for LASI interrupts from the PHY, but in
practice we have never implemented this in reference designs. Instead
we have polled, inserted the appropriate events, and then handled the
events later. This is a waste of time and code.
Instead, make PHY poll functions update the link state synchronously
and report whether it changed. We can still make use of the LASI
registers as a shortcut on the SFT9001.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 25 Nov 2009 07:54:54 +0000 (07:54 +0000)]
vlan: support "loose binding" to the underlying network device
Currently the UP/DOWN state of VLANs is synchronized to the state of the
underlying device, meaning all VLANs are set down once the underlying
device is set down. This causes all routes to the VLAN devices to vanish.
Add a flag to specify a "loose binding" mode, in which only the operstate
is transfered, but the VLAN device state is independant.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 25 Nov 2009 16:12:16 +0000 (16:12 +0000)]
sfc: Change MAC promiscuity and multicast hash at the same time
From: Steve Hodgson <shodgson@solarflare.com>
Currently we can set multicast hash immediately (in atomic context)
but must delay setting MAC promiscuity. There is not that much
point in deferring one but not the other, and setting the multicast
hash on Siena will involve a firmware request. So process them
both in efx_mac_work().
Also, set the broadcast bit in the multicast hash in
efx_set_multicast_list(), since this is required for both Falcon and
Siena.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 25 Nov 2009 16:12:01 +0000 (16:12 +0000)]
sfc: Simplify XMAC link polling
From: Steve Hodgson <shodgson@solarflare.com>
Only the XMAC on Falcon needs help from the driver to poll and reset
the MAC-PHY link (XAUI); GMII is a simple parallel bus and on later
NICs firmware takes care of the XAUI link. Also, an XMAC interrupt
currently schedules a work item which simply clears a flag
(efx_nic::mac_up) to be checked by the regular monitor (or the next
link reconfiguration, if that is sooner).
Rename the flag to xmac_poll_required, changing its sense. Remove the
needless indirection and just set the flag immediately. Call
falcon_xmac_poll() directly where required.
Add a new generic operation mac_op::check_fault to check the link
outside of regular monitoring, as required during self-tests.
(Note that this leaves us with an unused work item, but we will
immediately have another use for it.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 25 Nov 2009 16:11:35 +0000 (16:11 +0000)]
sfc: Split MAC stats DMA initiation and completion
From: Steve Hodgson <shodgson@solarflare.com>
Currently we initiate MAC stats DMA and busy-wait for completion when
stats are requested. We can improve on this with a periodic timer to
initiate and poll for stats, and opportunistically poll when stats are
requested.
Since efx_nic::stats_disable_count and efx_stats_{disable,enable}()
are Falcon-specific, rename them and move them accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 25 Nov 2009 16:11:19 +0000 (16:11 +0000)]
sfc: Hold MAC lock for longer in efx_init_port()
Although efx_init_port() is only called at probe time and so cannot
race with port reconfiguration, most of the functions it calls can
expect to be called with the MAC lock held.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 25 Nov 2009 16:09:55 +0000 (16:09 +0000)]
sfc: Fix bugs in RX queue flushing
Avoid overrunning the hardware limit of 4 concurrent RX queue flushes.
Expand the queue flush state to support this. Make similar changes to
TX flushing to keep the code symmetric.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 25 Nov 2009 16:08:41 +0000 (16:08 +0000)]
sfc: Treat all MAC registers as 128-bit
Although all the defined fields in these registers are within 32 bits,
they are architecturally defined as 128-bit like most other Falcon
registers. In particular, we must use efx_reado() to ensure proper
locking when reading MD_STAT_REG.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 26 Nov 2009 06:07:11 +0000 (06:07 +0000)]
macvlan: export macvlan mode through netlink
In order to support all three modes of macvlan at
runtime, extend the existing netlink protocol
to allow choosing the mode per macvlan slave
interface.
This depends on a matching patch to iproute2
in order to become accessible in user land.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 26 Nov 2009 06:07:10 +0000 (06:07 +0000)]
macvlan: implement bridge, VEPA and private mode
This allows each macvlan slave device to be in one
of three modes, depending on the use case:
MACVLAN_PRIVATE:
The device never communicates with any other device
on the same upper_dev. This even includes frames
coming back from a reflective relay, where supported
by the adjacent bridge.
MACVLAN_VEPA:
The new Virtual Ethernet Port Aggregator (VEPA) mode,
we assume that the adjacent bridge returns all frames
where both source and destination are local to the
macvlan port, i.e. the bridge is set up as a reflective
relay.
Broadcast frames coming in from the upper_dev get
flooded to all macvlan interfaces in VEPA mode.
We never deliver any frames locally.
MACVLAN_BRIDGE:
We provide the behavior of a simple bridge between
different macvlan interfaces on the same port. Frames
from one interface to another one get delivered directly
and are not sent out externally. Broadcast frames get
flooded to all other bridge ports and to the external
interface, but when they come back from a reflective
relay, we don't deliver them again.
Since we know all the MAC addresses, the macvlan bridge
mode does not require learning or STP like the bridge
module does.
Based on an earlier patch "macvlan: Reflect macvlan packets
meant for other macvlan devices" by Eric Biederman.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Patrick McHardy <kaber@trash.net> Cc: Eric Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Kagstrom [Wed, 25 Nov 2009 22:10:34 +0000 (22:10 +0000)]
via-velocity: Change DMA_LENGTH_DEF (from the VIA driver)
The VIA driver has changed the default for the DMA_LENGTH_DEF parameter.
Together with adaptive interrupt supression and NAPI support, this
improves performance quite a bit
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Kagstrom [Wed, 25 Nov 2009 22:10:26 +0000 (22:10 +0000)]
via-velocity: Implement NAPI support
This patch adds NAPI support for VIA velocity. The new velocity_poll
function also pairs tx/rx handling twice which improves perforamance on
some workloads (e.g., netperf UDP_STREAM) significantly (that part is
from the VIA driver).
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Kagstrom [Wed, 25 Nov 2009 22:10:12 +0000 (22:10 +0000)]
via-velocity: Add ethtool interrupt coalescing support
(Partially from the upstream VIA driver). Tweaking the number of
frames-per-interrupt and timer-until-interrupt can reduce the amount of
CPU work quite a lot.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Willi [Wed, 25 Nov 2009 00:58:39 +0000 (00:58 +0000)]
xfrm: Add SHA384 and SHA512 HMAC authentication algorithms to XFRM
These algorithms use a truncation of 192/256 bits, as specified
in RFC4868.
Signed-off-by: Martin Willi <martin@strongswan.org> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Willi [Wed, 25 Nov 2009 00:29:52 +0000 (00:29 +0000)]
xfrm: Store aalg in xfrm_state with a user specified truncation length
Adding a xfrm_state requires an authentication algorithm specified
either as xfrm_algo or as xfrm_algo_auth with a specific truncation
length. For compatibility, both attributes are dumped to userspace,
and we also accept both attributes, but prefer the new syntax.
If no truncation length is specified, or the authentication algorithm
is specified using xfrm_algo, the truncation length from the algorithm
description in the kernel is used.
Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Willi [Wed, 25 Nov 2009 00:29:51 +0000 (00:29 +0000)]
xfrm: Define new XFRM netlink auth attribute with specified truncation bits
The new XFRMA_ALG_AUTH_TRUNC attribute taking a xfrm_algo_auth as
argument allows the installation of authentication algorithms with
a truncation length specified in userspace, i.e. SHA256 with 128 bit
instead of 96 bit truncation.
Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Wed, 25 Nov 2009 23:40:35 +0000 (15:40 -0800)]
net: convert /proc/net/rt_acct to seq_file
Rewrite statistics accumulation to be in terms of structure fields,
not raw u32 additions. Keep them in same order, though.
This is the last user of create_proc_read_entry() in net/,
please NAK all new ones as well as all new ->write_proc, ->read_proc and
create_proc_entry() users. Cc me if there are problems. :-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 23 Nov 2009 16:07:30 +0000 (16:07 +0000)]
sfc: Combine high-level header files
All files that include ethtool.h, rx.h or tx.h are also including
efx.h, and there is no good reason to separate out the few
declarations they contain. Therefore fold them into efx.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 23 Nov 2009 16:04:23 +0000 (16:04 +0000)]
sfc: Rename efx_board::init_leds to init_phy and use for SFN4111T
efx_board::init_leds was introduced as a second stage of
initialisation because of the inter-dependency between the board and
PHY. We want to move board initialisation into NIC probing, which is
too early to use MDIO, so SFN4111T initialisation also needs to be
split.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 23 Nov 2009 16:03:45 +0000 (16:03 +0000)]
sfc: Use a single blink implementation
Only some PHYs have firmware support for a LED blink mode, so we
currently blink the others in a timer function. Since all PHYs have
simple on and off modes, we don't gain anything by using multiple
blink implementations. Also, since we have a process context there
is no need to use a timer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Mon, 23 Nov 2009 19:58:06 +0000 (20:58 +0100)]
ssb: Fix range check in sprom write
The range check in the sprom image parser hex2sprom() is broken.
One sprom word is 4 hex characters.
This fixes the check and also adds much better sanity checks to the code.
We better make sure the image is OK by doing some sanity checks to avoid
bricking the device by accident.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Sun, 22 Nov 2009 18:16:47 +0000 (20:16 +0200)]
rndis_wlan: disable stall workaround
Stall workaround doesn't work with bcm4320a devices like with bcm4320b.
This workaround actually causes more stalls/device freeze on bcm4320a.
Therefore disable stall workaround by default.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Sun, 22 Nov 2009 18:16:42 +0000 (20:16 +0200)]
rndis_wlan: fix buffer overflow in rndis_query_oid
rndis_query_oid overwrites *len which stores buffer size to return full size
of received command and then uses *len with memcpy to fill buffer with
command.
Ofcourse memcpy should be done before replacing buffer size.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Warning(net/mac80211/sta_info.h:322): No description found for parameter 'drv_unblock_wk'
Warning(net/mac80211/sta_info.h:322): No description found for parameter 'drv_unblock_wk'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: John W. Linville <linville@tuxdriver.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:05:09 +0000 (12:05 -0800)]
iwlwifi: remove reset led_tpt from iwl_leds_init()
Current blinking rate is calculated based on the difference between
current tx/rx byte counts and priv->led_tpt.
priv->led_tpt should not get reset in iwl_leds_init(), this function can be
called by bring interface "up" or "down", or when uCode sysassert occurred.
resetting the led_tpt parameter will introduce incorrect led blinking behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:05:08 +0000 (12:05 -0800)]
iwlwifi: change message for cmd queue full error
Change error message for command queue full
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Acked-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:05:07 +0000 (12:05 -0800)]
iwlwifi: print limited number of event log when uCode error
To help iwlagn uCode debugging, event log will dump to syslog when driver
detect uCode error occurred, but this only happen when compile with
CONFIG_IWLWIFI_DEBUG and debug flag is enabled; which is not always
the case. Also, there is another problem, if the flag is set, the entire
event log buffer will be dump to syslog, it can flood the syslog and
make it very difficult to debug the problem.
Change the default to only dump last 20 entries of event log to syslog
unless the following condition meets:
1. both compile with CONFIG_IWLWIFI_DEBUG and debug flag
is enabled, and then dump the entire event buffer to syslog.
2. dump event log request from debugfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Acked-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jay Sternberg [Fri, 20 Nov 2009 20:05:06 +0000 (12:05 -0800)]
iwlwifi: Tell the ucode immediately when association state changes
When we get a state change of associated or not, we need to tell the
ucode via the RX_ON command using the filter flags. This will prevent
the ucode from sending any packets when not associated, specifically not
sending NULL QOS packets after a deauthentication which causes the AP to
repeatedly send deauth's in some situations.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:05:05 +0000 (12:05 -0800)]
iwlwifi: dump error log when uCode error occurred
uCode error log contain information as to what the error was and where
it occurred necessary to debug any uCode issues.
Always log the information without special debug flag, this can help to
capture the important information when error happened.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Acked-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:05:04 +0000 (12:05 -0800)]
iwlwifi: by default, dump entire sram data portion
For "sram" debugfs file, if user did not specify the offset and length,
dump the entire data portion of sram by default.
Data portion is 0x800000 - 0x80ffff, but the actual data size is known
to the driver from the ucode file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:05:03 +0000 (12:05 -0800)]
iwlwifi: update supported PCI_ID list for 5xx0 series
Update the PCI_ID list for 5xx0 series.
Remove all the PCI_IDs which never made into production or not longer in
production.
Also make sure the supported bands(a/b/g/n) match specified PCI_IDs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 20 Nov 2009 20:05:02 +0000 (12:05 -0800)]
iwlwifi: separate IO tracing
Since IO tracing is usually not needed and
generates a lot of data, separate it into
its own trace system so that we can always
enable iwlwifi:* and not have to worry about
getting too much data. If IO tracing is then
really needed we can enable iwlwifi_io:* in
addition and get that data.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:05:01 +0000 (12:05 -0800)]
iwlwifi: fix reserved2 field in iwl4965_addsta
reserved2 field in "struct iwl4965_addsta_cmd" is __le16.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:05:00 +0000 (12:05 -0800)]
iwlwifi: dynamically allocate buffer for sram debugfs file
Dynamically allocate memory for dumping SRAM based on the length of memory
to be displayed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:04:59 +0000 (12:04 -0800)]
iwlwifi: increase tx_queue debugfs buffer size
For tx_queue, need to increase the buffer size allocated for it,
so all the queues information can be displayed
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:04:58 +0000 (12:04 -0800)]
iwlwifi: set read/write permission for debugfs files
Set the correct Read/Write file permission for iwlwifi debugfs files
based on the functionality of the files
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:04:56 +0000 (12:04 -0800)]
iwlwifi: reset led_tpt when clear tx/rx traffic byte counts
LED blink rate is based on the traffic load, when tx/rx traffic counts
got reset, we also need to reset the led_tpt to prevent incorrect
blink rate being calculated.
Merge both clear_tx_statistics() and clear_rx_statistics() into
single clear_traffic_statistics() function, when reset the traffic byte
counts, both tx and rx need to be reset at the same time, to make
sure calculated the correct led blink rate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 Nov 2009 20:04:55 +0000 (12:04 -0800)]
iwlwifi: set sm_ps_mode as part of cfg parameters
Setting "Spatial multiplexing Power Save" as part of
per device configuration parameter.
Report to uCode based on priv->conf setting, so driver can
have more control of how different devices should operate
in power save mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill [Fri, 20 Nov 2009 20:04:53 +0000 (12:04 -0800)]
iwlagn: Use iwl_write8() for CSR_INT_COALESCING register
CSR_INT_COALESCING previously had only one, but now has two single-byte fields.
With only one single-byte field (lowest order byte) it was okay to write via
iwl_write32(), but now with two, an iwl_write32() to the lower order field
clobbers the other field (odd-address CSR_INT_PERIODIC_REG, offset 0x5), and an
iwl_write32() to CSR_INT_PERIODIC_REG could clobber the lowest byte of the
next-higher register (CSR_INT, offset 0x8).
Fortunately, no bad side effects have been produced by the iwl_write32()
usage, due to order of execution (low order byte was always written before
higher order byte), and the fact that writing "0" to the low byte of the
next higher register has no effect (only action is when writing "1"s).
Nonetheless, this cleans up the accesses so no bad side effects might occur
in the future, if execution order changes, or more bit fields get added to
CSR_INT_COALESCING.
Add some comments regarding periodic interrupt usage.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill [Fri, 20 Nov 2009 20:04:52 +0000 (12:04 -0800)]
iwlwifi: Add iwl_write8()
To support byte writes to CSR_INT_COALESCING and CSR_INT_PERIODIC registers,
add iwl_write8(), including debug/trace support.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lukáš Turek [Thu, 19 Nov 2009 22:02:02 +0000 (23:02 +0100)]
ath5k: Fix I/Q calibration
The sign of correction coefficients was lost in the calculations, which
caused high packetloss in 802.11a mode after the results were applied.
Fixed by removing unneccesary and broken AND with a bit mask.
Signed-off-by: Lukas Turek <8an@praha12.net> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Thu, 19 Nov 2009 21:24:29 +0000 (22:24 +0100)]
b43: Rewrite DMA Tx status handling sanity checks
This rewrites the error handling policies in the TX status handler.
It tries to be error-tolerant as in "try hard to not crash the machine".
It won't recover from errors (that are bugs in the firmware or driver),
because that's impossible. However, it will return a more or less useful
error message and bail out. It also tries hard to use rate-limited messages
to not flood the syslog in case of a failure.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: This patch fix RX unpadding for any received frame.
It has been tested with a 802.11 frame generator and by checking the FCS field
of each received frame with the value reported by the Atheros hardware. This
patch is useful if you are trying to analyze non standard 802.11 frame going
over the air.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 19 Nov 2009 20:40:46 +0000 (14:40 -0600)]
ssb: Unconditionally log results of core scans
At present, the results of an SSB core scan are only logged when
CONFIG_SSB_DEBUG is "y". As this may not be set in a distro kernel,
it is difficult interpret many problems posted in bug reports or in
help forums.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Matthew Garrett [Wed, 11 Nov 2009 19:36:31 +0000 (14:36 -0500)]
ipw2200: Set core hw rfkill status when hardware changes state
ipw2200 is able to detect when it's been hard-killed, but doesn't update
the core rfkill state or update userspace. Ensure that the state is updated,
allowing the rfkill core to notify userspace.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Matthew Garrett [Wed, 11 Nov 2009 19:36:30 +0000 (14:36 -0500)]
ipw2100: Register the wiphy device
libipw unconditionally calls wiphy_unregister, but it's up to the driver
to register it in the first place. ipw2100 fails to do so. Add the necessary
glue code, and also ensure that rfkill statuses get set up appropriately.
(Augmented for proper wiphy_unregister placement. -- JWL)
Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 25 Aug 2009 18:12:25 +0000 (14:12 -0400)]
libipw: initiate cfg80211 API conversion (v2)
Initiate the conversion of libipw to the new cfg80211 configuration API.
For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone. Eventually
migrate it to cfg80211 when the add/del/change_virtual_intf methods
are implemented.
(v2: Fix unconditional wiphy_unregister in libipw which was causing
problems for ipw2100, somewhat based on prior attempted fix
by Zhu Yi <yi.zhu@intel.com>. Previously both original version of
this patch and Zhu Yi's fix attempt were reverted due to
discovery of regressions. -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Duyck [Mon, 23 Nov 2009 06:32:57 +0000 (06:32 +0000)]
ixgbe: Only set/clear VFE in ixgbe_set_rx_mode
There appears to be a stray setting of the VFE bit when registering vlans.
This should not be done as vlan filtering should be enabled any time the
interface is not in promiscous mode
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe: Use rx buffer length from rx ring for configuring rscctl
While configuring rscctl use rx buffer length from rx ring structure
instead of passing rx_buf_len to ixgbe_configure_rscctl
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Divide 82599 HWRSC counters into aggregated and flushed to count number of
packets getting coalesced per TCP connection.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Sun, 22 Nov 2009 22:02:45 +0000 (22:02 +0000)]
be2net: remove BUG_ON() when be2net runs out of mccq wrbs
The driver can run out of mccq wrbs when completions don't arrive
due to an unresponsive card. This must not hit a BUG_ON(); instead
log a msg and return an error.
Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Sun, 22 Nov 2009 22:01:10 +0000 (22:01 +0000)]
be2net: support configuration of 64 multicast addresses instead of 32
To send upto 64 addresses in the multicast-set cmd, the non-embeeded cmd format
that provides for a bigger buffer is used instead of an embedded format.
Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Mon, 23 Nov 2009 18:41:23 +0000 (10:41 -0800)]
net/ipv4: Move && and || to end of previous line
On Sun, 2009-11-22 at 16:31 -0800, David Miller wrote:
> It should be of the form:
> if (x &&
> y)
>
> or:
> if (x && y)
>
> Fix patches, rather than complaints, for existing cases where things
> do not follow this pattern are certainly welcome.
Also collapsed some multiple tabs to single space.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mv-sheeva.git / log