Daniel Vetter [Wed, 5 Jun 2013 11:34:22 +0000 (13:34 +0200)]
drm/i915: simplify the reduced clock handling for pch plls
Just move the lowfreq_avail logic out of the register writing as a
prep step for the next patch, which will coalesce all the pch pll
enabling into one spot.
Note that writing the reduced clock dividers to FP1 in a few more
cases (as this patch ends up doing) isn't really relevant since the
FP1 value only matters when we enable the low lock. Which despite
can only happen if we've actually enabled the reduced dotclock and
furthermore isn't even properly implemented on ilk+: Despite claims to
the contrary in the code switching between frequencies if fully
manual.
v2: Explain matters around the FP1 change to answer a question Damien
raised in his review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 6 Jun 2013 20:22:47 +0000 (22:22 +0200)]
drm/i915: stop killing pfit on i9xx
Nowadays (i.e. with Valleyview) we also have edp on non-PCH_SPLIT
platforms, so just checking for LVDS is not good enough.
Secondly we have full pfit pipe config tracking, so we'll correctly
disable the pfit as part of the initial modeset.
For fastboot we need a bit of work here to correctly kill unsupported
configs (if e.g. the pfit is used on anything else than the built-in
panel). But since that's not yet supported we don't need to worry.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 12 Jun 2013 22:54:59 +0000 (00:54 +0200)]
drm/i915: explicitly set up PIPECONF (and gamma table) on haswell
Again we don't really support different settings, so don't let the
BIOS sneak stuff through.
Since the motivation for this patch series is to ensure we have the
correct gamma table mode selected also add the required write to the
GAMMA_MODE register to select the 8bit legacy table.
And since I find lowercase letters in #defines offensive, also
bikeshed those.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 12 Jun 2013 22:54:58 +0000 (00:54 +0200)]
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
Same reasons as for the previous patch, just no bug report about
anything going wrong yet: We only support exactly the mode we program,
so don't leave any stale BIOS state behind.
Again this will be fun to properly track for fastboot.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 12 Jun 2013 22:54:57 +0000 (00:54 +0200)]
drm/i915: set up PIPECONF explicitly on ilk-ivb
Dragging random garbage along from the BIOS isn't a good idea, since
we really only support exactly what we've set up.
In the specific case for the bug reporter the BIOS used the 10bit
gamma table, but since we only support an 8bit table the dark colors
ended up all wrong and the light ones all unadjusted.
Note that this has a nice implication for fastboot, it essentially
means that we have quite a bit more state to check and compare before
we can decide whether fastboot is possible.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65593 Reported-and-Tested-by: Thomas Hebb <tommyhebb@gmail.com> Cc: stable@vger.kernel.org Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Wed, 12 Jun 2013 12:13:20 +0000 (15:13 +0300)]
drm/i915: find guilty batch buffer on ring resets
After hang check timer has declared gpu to be hung,
rings are reset. In ring reset, when clearing
request list, do post mortem analysis to find out
the guilty batch buffer.
Select requests for further analysis by inspecting
the completed sequence number which has been updated
into the HWS page. If request was completed, it can't
be related to the hang.
For noncompleted requests mark the batch as guilty
if the ring was not waiting and the ring head was
stuck inside the buffer object or in the flush region
right after the batch. For everything else, mark
them as innocents.
v2: Fixed a typo in commit message (Ville Syrjälä)
v3: - more descriptive function parameters (Chris Wilson)
- use masked head address when inspecting if request is in ring
- s/hangcheck.last_action/hangcheck.action
- added comment about unmasked head hitting batch_obj range
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Wed, 12 Jun 2013 09:35:32 +0000 (12:35 +0300)]
drm/i915: store ring hangcheck action
For guilty batchbuffer analysis later on when rings are reset,
store what state the ring was on when hang was declared.
This helps to weed out the waiting rings from the active ones.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Wed, 12 Jun 2013 12:01:39 +0000 (15:01 +0300)]
drm/i915: add batch bo to i915_add_request()
In order to track down a batch buffer and context which
caused the ring to hang, store reference to bo into the request struct.
Request can also cause gpu to hang after the batch in the flush section
in the ring. To detect this add start of the flush portion offset into the
request.
v2: Included comment about request vs batch_obj lifetimes (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Wed, 12 Jun 2013 09:35:30 +0000 (12:35 +0300)]
drm/i915: change i915_add_request to macro
Only execbuffer needed all the parameters on i915_add_request().
By putting __i915_add_request behind macro, all current callsites
become cleaner. Following patch will introduce a new parameter
for __i915_add_request. With this patch, only the relevant callsite
will reflect the change making commit smaller and easier to understand.
v2: _i915_add_request as function name (Chris Wilson)
v3: change name __i915_add_request and fix ordering of params (Ben Widawsky)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Wed, 12 Jun 2013 09:35:29 +0000 (12:35 +0300)]
drm/i915: add i915_gem_context_get_hang_stats()
To get context hang statistics for specified context,
add i915_gem_context_get_hang_stats().
For arb-robustness, every context needs to have its own
hang statistics tracking. Added function will return
the user specified context statistics or in case of
default context, statistics from drm_i915_file_private.
v2: handle default context inside get_reset_state
v3: return struct pointer instead of passing it in as param
(Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Wed, 12 Jun 2013 09:35:28 +0000 (12:35 +0300)]
drm/i915: add struct i915_ctx_hang_stats
To count context losses, add struct i915_ctx_hang_stats for
both i915_hw_context and drm_i915_file_private.
drm_i915_file_private is used when there is no context.
v2: renamed and cleaned up the struct (Chris Wilson, Ian Romanick)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 12 Jun 2013 19:11:18 +0000 (22:11 +0300)]
drm/i915: Try harder to disable trickle feed on VLV
The specs are a bit unclear whether the per-plane trickle feed disable
control exists on VLV. There is another trickle feed disable control
in the MI_ARB register.
After some experimentation it turns out both the DSPCNTR trickle feed
bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't
seem to have any effect.
The MI_ARB bit, on the other hand, has a noticable effect. I performed
an experiment where I reduced the FIFO size via DSPARB and observed the
effect of the MI_ARB trickle feed bit on the display.
Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have
problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems
didn't start until DSPARB=0x09090909. This seems to confirm that the
MI_ARB trickle feed bit actually does work.
So replace the use of the DSPCNTR trickle feed bits with MI_ARB
on VLV.
v2: Amend commit message with results from experimentation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 5 Jun 2013 11:34:21 +0000 (13:34 +0200)]
drm/i915: fix up pch pll enabling for pixel multipliers
We have a nice comment saying that the pixel multiplier only sticks
once the vco is on and stable. The only problem is that the enable bit
wasn't set at all. This patch fixes this and so brings the ilk+ pch
pll code in line with the i8xx/i9xx pll code. Or at least improves
matters a lot.
This should fix sdvo on ilk-ivb for low-res modes.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 5 Jun 2013 11:34:20 +0000 (13:34 +0200)]
drm/i915: hw state readout and cross-checking for shared dplls
Just the plumbing, all the modeset and enable code has not yet been
switched over to use the new state. It seems to be decently broken
anyway, at least wrt to handling of the special pixel mutliplier
enabling sequence. Follow-up patches will clean up that mess.
Another missing piece is more careful handling (and fixup) of the fp1
alternate divisor state. The BIOS most likely doesn't bother to
program that one to what we expect. So we need to be more careful with
comparing that state, both for cross checking but also when checking
for dpll sharing when acquiring shared dpll. Otherwise fastboot will
deny a few shared dpll configurations which would otherwise work.
v2: We need to memcpy the pipe config dpll hw state into the pll, for
otherwise the cross-check code will get angry.
v3: Don't forget to read the pch pll state in the crtc get_pipe_config
function for ibx/ilk platforms.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 5 Jun 2013 11:34:19 +0000 (13:34 +0200)]
drm/i915: WARN on lack of shared dpll
Now that we have proper hw state reconstruction we should never have a
case where we don't have the software dpll state properly set up. So
add WARNs to the respective !pll cases in enable/disabel_shared_dpll.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 5 Jun 2013 11:34:16 +0000 (13:34 +0200)]
drm/i915: display pll hw state readout and checking
Currently still with an empty register state, this will follow in a
next step. This one here just creates the new vfunc and uses it for
cross-checking, initial state takeover and the dpll assert function.
And add a FIXME for the ddi pll readout code, which still needs to be
converted over.
v2:
- Add some hw state readout debug output.
- Also cross check the enabled crtc counting.
Note that I've botched up the patch ordering, and before this patch
we've read out the pll selection correctly, but did not reconstruct
the refcounts properly. See the bug link.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65673 Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 21 May 2013 19:54:55 +0000 (21:54 +0200)]
drm/i915: pnv dpll doesn't use m1!
So don't try to store it in the DPLL_FP register.
Otherwise it looks like the limits for pineview are correct: It has
it's own clock computation code, which doesn't use an offset for n
divisors, and the register value based m limits look sane enough.
v2: Rebase on top of the pineview clock refactor and fixup up the
commit message: It's m1 pnv doens't care about, not m2!
Quoting Damien's review:
- "n can vary between 2 and 6, but we declare the 3-6 as limits.
- "p1 seems to be able to go up to 9
- "the m upper limit seems a bit big, but the docs are a bit shy on
that values for pnv.
"Otherwise, the change itself seems good:"
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 12 Jun 2013 09:47:24 +0000 (11:47 +0200)]
drm/i915: disable sdvo pixel multiplier cross-check for HAS_PCH_SPLIT
We don't (yet) have proper pixel multiplier readout support on pch
split platforms, so the cross check will naturally fail.
v2: Fix spelling in the comment, spotted by Ville.
v3: Since the ordering constraint is pretty tricky between the crtc
get_pipe_config callback and the encoder->get_config callback add a
few comments about it. Prompted by a discussion with Chris Wilson on
irc about why this does work anywhere else than on i915g/gm.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 12 Jun 2013 10:29:47 +0000 (11:29 +0100)]
drm/i915: WARN if the fence pin_count is invalid
Stéphane Marchesin found a bug where the fences were not being restored,
and in particular the fence pin_count was incorrect. Had we had a
warning in place, this bug would have come to light much earlier. Better
late than never?
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Stéphane Marchesin <marcheu@chromium.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 10 Jun 2013 10:20:22 +0000 (11:20 +0100)]
drm/i915: Eliminate the addr/seqno from the hangcheck warning
This is of no value to the developer reading the report, let alone the
bamboozled user.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 10 Jun 2013 10:20:21 +0000 (11:20 +0100)]
drm/i915: Don't count semaphore waits towards a stuck ring
If we detect a ring is in a valid wait for another, just let it be.
Eventually it will either begin to progress again, or the entire system
will come grinding to a halt and then hangcheck will fire as soon as the
deadlock is detected.
This error was foretold by Ben in
commit 05407ff889ceebe383aa5907219f86582ef96b72
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu May 30 09:04:29 2013 +0300
drm/i915: detect hang using per ring hangcheck_score
"If ring B is waiting on ring A via semaphore, and ring A is making
progress, albeit slowly - the hangcheck will fire. The check will
determine that A is moving, however ring B will appear hung because
the ACTHD doesn't move. I honestly can't say if that's actually a
realistic problem to hit it probably implies the timeout value is too
low."
v2: Make sure we don't even incur the KICK cost whilst waiting.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65394 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 10 Jun 2013 10:20:20 +0000 (11:20 +0100)]
drm/i915: Only slightly increment hangcheck score if we succesfully kick a ring
After kicking a ring, it should be free to make progress again and so
should not be accused of being stuck until hangcheck fires once more. In
order to catch a denial-of-service within a batch or across multiple
batches, we still do increment the hangcheck score - just not as
severely so that it takes multiple kicks to fail.
This should address part of Ben's justified criticism of
drm/i915: detect hang using per ring hangcheck_score
"There's also another corner case on the kick. If the seqno = 2
(though not stuck), and on the 3rd hangcheck, the ring is stuck, and
we try to kick it... we don't actually try to find out if the kick
helped."
v2: Make sure we catch DoS attempts with batches full of invalid WAITs.
v3: Preserve the ability to detect loops by always charging the ring
if it is busy on the same request.
v4: Make sure we queue another check if on a new batch
References: https://bugs.freedesktop.org/show_bug.cgi?id=65394 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 10 Jun 2013 10:20:19 +0000 (11:20 +0100)]
drm/i915: Initialize ring->hangcheck upon ring init
When we reset and restart a ring, we also want to clear any existing
hangcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 5 Jun 2013 11:34:14 +0000 (13:34 +0200)]
drm/i915: enable/disable hooks for shared dplls
Looks at first like a bit of overkill, but
- Haswell actually wants different enable/disable functions for
different plls.
- And once we have full dpll hw state tracking we can move the full
register setup into the ->enable hook.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 7 Jun 2013 21:11:08 +0000 (23:11 +0200)]
drm/i915: hw state readout for shared pch plls
Well, the first step of a long road at least, it only reads out
the pipe -> shared dpll association thus far. Other state which needs
to follow:
- hw state of the dpll (on/off + dpll registers). Currently we just
read that out from the hw state, but that doesn't work too well when
the dpll is in use, but not yet fully enabled. We get away since
most likely it already has been enabled and so the correct state is
left behind in the registers. But that doesn't hold for atomic
modesets when we want to enable all pipes at once.
- Refcount reconstruction for each dpll.
- Cross-checking of all the above. For that we need to keep the dpll
register state both in the pipe and in the shared_dpll struct, so
that we can check that every pipe is still connected to a correctly
configured dpll.
Note that since the refcount resconstruction isn't done yet this will
spill a few WARNs at boot-up while trying to disable pch plls which
have bogus refcounts. But since there's still a pile of refactoring to
do I'd like to lock down the state handling as soon as possible hence
decided against reordering the patches to quiet these WARNs - after
all the issues they're complaining about have existed since forever,
as Jesse can testify by having pch pll states blow up consistently in
his fastboot patches ...
v2: We need to preserve the old shared_dpll since currently the
shared dpll refcount dropping/getting is done in ->mode_set. With
the usual pipe_config infrastructure the old dpll id is already lost
at that point, hence preserve it in the new config.
v3: Rebase on top of the ips patch from Paulo.
v4: We need to unconditionally take over the shared_dpll id from the
old pipe config when e.g. doing a direct pch port -> cpu edp
transition.
v5: Move the saving of the old shared_dpll id to an ealier patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 5 Jun 2013 11:34:09 +0000 (13:34 +0200)]
drm/i915: refactor PCH_DPLL_SEL #defines
The bits are evenly space, so we can cut down on two big switch
blocks. This also greatly simplifies the hw state readout which
follows in the next patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 7 Jun 2013 21:10:32 +0000 (23:10 +0200)]
drm/i915: move shared_dpll into the pipe config
With the big sed-job prep work done this is now really simple. With
the exception that we only assign the right shared dpll id in the
->mode_set callback but also depend upon the old one still being
around.
Until that mess is fixed up we need to jump through a few hoops to
keep the old value save.
v2: Kill the funny whitespace spotted by Chris.
v3: Move the shared_dpll pipe config fixup into this patch as noticed
by Ville. Also unconditionally set the shared_dpll with the current
one, since otherwise we won't handle direct pch port -> cpu edp
transitions correctly.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 7 Jun 2013 21:10:03 +0000 (23:10 +0200)]
drm/i915: switch crtc->shared_dpll from a pointer to an enum
Dealing with discrete enum values is simpler for hw state readout and
pipe config computations than pointers - having neat names instead of
chasing pointers should look better in the code.
This isn't a that good reason for pch plls, but on haswell we actually
have 3 different types of plls: WRPLL, SPLL and the DP clocks. Having
explicit names should help there.
Since this also adds the intel_crtc_to_shared_dpll helper to further
abstract away the crtc -> dpll relationship this will also help to
make the next patch simpler, which moves the shared dpll into the pipe
configuration.
Also note that for uniformity we have two special dpll ids: NONE for
pipes which need a shared pll but don't have one (yet) and private for
when there's a non-shared pll (e.g. per-pipe or per-port pll).
I've thought whether we should also add a 2nd enum for the type of the
pll we want (for really generic pll selection code) but thrown that
idea out again - likely there's too much platform craziness going on
to be able to share the pll selection logic much.
Since this touched all the shared_pll functions a bit I've also done
an s/intel_crtc/crtc/ replacement on a few of them.
v2: Kill DPLL_ID_NONE. It's probably better to call it DPLL_ID_INVALID and use
it to check that the compute config stage assigns a dpll to every pipe.
But since that code isn't ready yet until we move the dpll selection out
of the ->mode_set callback, there's no use for it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 5 Jun 2013 11:34:06 +0000 (13:34 +0200)]
drm/i915: s/pch_pll/shared_dpll/
For fastboot we need some support to read out the sharing state of
plls, at least for platforms where they can be shared (or freely
assigned at least). Now for ivb we already have pretty extensive
infrastructure for tracking pch plls, and it took us an aweful lot of
tries to get that remotely right. Note that hsw could also share plls,
but even now they're already freely assignable. So we need this on
more than just ivb.
So on top of the usual fastboot fun pll sharing seems to be an
additional step up in fragility. Hence a common infrastructure for all
shared/freely assignable display plls seems to be in order.
The plan is to have a bit of dpll hw state readout code, which can be
used individually, but also to fill in the pipe config. The hw state
cross check code will then use that information to make sure that
after every modeset every pipe still is connected to a pll which still
has the correct configuration - a lot of the pch pll sharing bugs
where due to incorrect sharing.
We start this endeavour with a simple s/pch_pll/shared_dpll/ rename
job.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 10 Jun 2013 15:28:22 +0000 (17:28 +0200)]
drm/i915: lock down pch pll accouting some more
Before I start to make a complete mess out of this, crank up
the paranoia level a bit.
v2: Kill the has_pch_encoder check in put_shared_dpll - it's invalid
as spotted by Ville since we currently only put the dpll when we
already have the new pipe config. So a direct pch port -> cpu edp
transition will hit this.
v3: Now that I've lifted my blinders add the WARN_ON Ville requested.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 5 Jun 2013 11:34:03 +0000 (13:34 +0200)]
drm/i915: fix up pch pll handling in ->mode_set
We ->mode_set is called we can't just blindly reuse an existing pll
since that might be shared with a different, still active pch output.
v2: Only update the pll settings when the pch pll is know to be
unused, otherwise we can wreak havoc with a running pipe. Which in the
case of DP will likely result in a black screen due to loss of link
lock.
v3: Tighten up the asserts a bit more, especially make sure that the
pch pll is still enabled when we try to disable it. This would have
caught the bug fixed in this patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Mon, 10 Jun 2013 14:48:09 +0000 (15:48 +0100)]
drm/i915: Use FBINFO_STATE defines instead of 0 and 1
This makes, arguably, the condition on state easier to read.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Jun 2013 15:52:24 +0000 (18:52 +0300)]
drm/i915: Make g4x_fixup_plane() operational again
Don't enable the cursor until g4x_fixup_plane() had a chance to do
cast its magic spell.
Egbert writes:
"Today I had the chance to test this. First I tried
if I can still reproduce the blank with this patch
added when I disable my voodoo g4x_fixup_plane():
It turned out it still happens however very rarely
(like 1 out of 20 tries). When I reenabled my voodoo
the issue still occurred.
I had to switch two lines around, ie:
intel_enable_plane(dev_priv, plane, pipe);
if (IS_G4X(dev))
g4x_fixup_plane(dev_priv, pipe);
+ intel_crtc_update_cursor(crtc, true);
to avoid the blank screen issue - which is it didn't
happen in ~75 tries."
v2: Add a comment to remind people of the ordering constraints
Acked-by: Egbert Eich <eich@suse.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Thu, 6 Jun 2013 19:58:16 +0000 (16:58 -0300)]
drm/i915: WA: FBC Render Nuke.
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Thu, 6 Jun 2013 19:53:41 +0000 (16:53 -0300)]
drm/i915: Track when we dirty the scanout with render commands
This is required for tracking render damage for use with FBC and will be
used in subsequent patches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Jun 2013 07:47:04 +0000 (10:47 +0300)]
drm/i915: Refactor ctg+ trickle feed disable
Pull the code to disable trickle feed for all primary planes into a
separate function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Jun 2013 07:47:03 +0000 (10:47 +0300)]
drm/i915: Disable trickle feed in ironlake_init_clock_gating()
We disable trickle feed in all the (relevant) clock gating functions,
except ironlake_init_clock_gating(). Copy paste the same code there as
well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Jun 2013 07:47:02 +0000 (10:47 +0300)]
drm/i915: Disable trickle feed via MI_ARB_STATE for the gen4
According to BSpec, trickle feed should be disabled for BW and
mobile CL. Those constraints seem to match all of our gen4 chipsets.
Trickle feed is disabled via the MI_ARB_STATE register instead of
per plane controls on gen4.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Jun 2013 07:47:01 +0000 (10:47 +0300)]
drm/i915: Disable primary plane trickle feed for g4x
The docs say that the trickle feed disable bit is present (for primary
planes only, not video sprites) on CTG, and that it must be set
for ELK. Just set it for all g4x chipsets.
v2: Do it in init_clock_gating too
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 1 Jun 2013 17:45:56 +0000 (19:45 +0200)]
drm/i915: enable 30bpp for DP outputs
We always limited the link bw calculations to 24bpp. Tested with
my shiny new high-bpc screen, seems to work as advertised.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65280 Tested-by: shui yangwei <yangweix.shui@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 6 Jun 2013 12:55:52 +0000 (14:55 +0200)]
drm/i915: pipe config quirk infrastructure plus sdvo mode.flags fix
For various reasons the hw state readout might not be able to
faithfully match the hw state:
- broken hw (like the case which motivated this patch here where the
sdvo encoder does not implemented mandatory functionality
correctly).
- platforms which are not supported fully with the pipe config
infrastructure
- if our code doesn't support a given hw configuration natively, e.g.
special restrictions on the per-pipe panel fitters when they're used
in high-quality scaling modes.
In all these cases both fastboot and the hw state cross checker need
to be aware of these cases and act accordingly. To be able to do this
add a new quirk flag to the pipe config structure.
The specific case at hand is an sdvo encoder which doesn't implement
the get_timings function, so adjusted_mode flags will be wrong. The
strange thing though is that the encoder _does_ work, even though it
doesn't implement any of the timings functions (so neither get nor
set, neither for input nor output timings).
Not that non-compliant sdvo encoder are any surprise at all ...
v2:
- Don't read random garbage from the dtd if the get_timings call
failed (suggested by Chris).
- Still check the interlaced flag, that's read out from someplace
else. We want maximal paranoia, after all.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wang Xingchao [Thu, 30 May 2013 14:07:11 +0000 (22:07 +0800)]
i915/drm: Add private api for power well usage
Haswell Display audio depends on power well in graphic side, it should
request power well before use it and release power well after use.
I915 will not shutdown power well if it detects audio is using.
This patch protects display audio crash for Intel Haswell C3 stepping board.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wang Xingchao [Thu, 30 May 2013 14:07:10 +0000 (22:07 +0800)]
ALSA: hda - Add power-welll support for haswell HDA
For Intel Haswell chip, HDA controller and codec have
power well dependency from GPU side. This patch added support
to request/release power well in audio driver. Power save
feature should be enabled to get runtime power saving.
There's deadlock when request_module(i915) in azx_probe.
It looks like:
device_lock(audio pci device) -> azx_probe -> module_request
(or symbol_request) -> modprobe (userspace) -> i915 init ->
drm_pci_init -> pci_register_driver -> bus_add_driver -> driver_attach ->
which in turn tries all locks on pci bus, and when it tries the one on the
audio device, it will deadlock.
This patch introduce a work to store remaining probe stuff, and let
request_module run in safe work context.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com> Reviewed-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Takashi Iwai [Thu, 30 May 2013 14:07:09 +0000 (22:07 +0800)]
ALSA: hda - Move azx_first_init() into azx_probe_continue()
This is a preliminary work for the upcoming Haswell HDMI audio fixes.
azx_first_init() function can be safely called after the f/w loader,
since the f/w loader doesn't require the sound hardware initialization
beforehand. Moving it into azx_probe_continue() cleans up the code
flow a bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wang Xingchao [Thu, 30 May 2013 14:07:08 +0000 (22:07 +0800)]
ALSA: hda - Fix runtime PM check
The device can support runtime PM no matter whether it support
signal wakeup or not. For some chips like Haswell which doesnot
support PME by default, this patch let haswell Display HD-A controller
enter runtime suspend, and bring more power saving whith power-well
feature enabled.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 4 Jun 2013 19:53:39 +0000 (16:53 -0300)]
drm/i915: update FBC maximum fb sizes
CTG/ILK/SNB/IVB support 4kx2k surfaces. HSW supports 4kx4k, but
without proper front buffer invalidation on the last 2k lines, so
don't enable FBC on these cases for now.
v2: Use gen >= 5, not gen > 4 (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 6 Jun 2013 10:45:25 +0000 (12:45 +0200)]
drm/i915: hw state readout support for pixel_multiplier
Incomplete since ilk+ support needs proper pch dpll tracking first.
SDVO get_config parts based on a patch from Jesse Barnes, but fixed up
to actually work.
v2: Make sure that we call encoder->get_config _after_ we
get_pipe_config to be consistent in both setup_hw_state and the
modeset state checker. Otherwise the clever trick with handling the
pixel mutliplier on i915G/GM where the encoder overrides the default
value of 1 from the crtc get_pipe_config function doesn't work.
Spotted by Imre Deak.
v3: Actually cross-check the pixel mutliplier (but not on pch split
platforms for now). Now actually also tested on a i915G with a sdvo
encoder plugged in.
Cc: Imre Deak <imre.deak@intel.com> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 4 Jun 2013 10:49:07 +0000 (13:49 +0300)]
drm/i915: Assert dpll running in intel_crtc_load_lut() on pre-PCH platforms
Adding more context from Ville's reply to Rodrigo's question why we
need this:
"The spec says that on some hardware you need to PLL running before you
can poke at the palette registers. I didn't actually try to anger the
hardware so I'm not really sure what would happen otherwise, but IIRC
Jesse said something about a hard system hang..."
And generally documenting such ordering constraints with asserts is
Just Good.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Spruce up the commit message a lot.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 4 Jun 2013 10:49:04 +0000 (13:49 +0300)]
drm/i915: Disable/restore all sprite planes around modeset
Disable/restore sprite planes around mode-set just like we do for the
primary and cursor planes. Now that we have working sprite clipping,
this actually works quite decently.
Previosuly we didn't even bother to disable sprites when changing mode,
which could lead to a corrupted sprite appearing on the screen after a
modeset (at least on my IVB). Not sure if all hardware generations would
be so forgiving when enabled sprites end up outside the pipe dimensons.
v2: Disable rather than enable sprites in ironlake_crtc_disable()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 4 Jun 2013 10:48:59 +0000 (13:48 +0300)]
drm/i915: Always load the display palette before enabling the pipe
Loading the palette after the planes are enabled can risk showing
incorrect colors. ILK+ already load the palette before even the pipe
is enabled. Just follow the same order for gen2-4 and VLV.
According to BSpec the requirements for palette access are
display core clock and display PLL running. In certain platforms
just the core clock may be enough. But we definitely should have both
running when this gets called during the modeset.
v2: Amend the commit message with some display PLL/core clock info
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 5 Jun 2013 17:21:51 +0000 (14:21 -0300)]
drm/i915: add ibx_irq_preinstall
So we can remove some duplicate code. All the PCHs are very similar
and right now the code is the same. I plan to add more code, so we
would have more duplicated code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 4 Jun 2013 22:49:08 +0000 (23:49 +0100)]
drm/i915: Track clients and print their object usage in debugfs
By stashing a pointer of who opened the device and keeping a list of
open fd, we can then walk each client and inspect how many objects they
have open. For example,
v2: Use existing drm->filelist as pointed out by Ben.
v3: Not even stashing the task_struct is required as Ben pointed out
drm_file->pid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 1 Jun 2013 15:17:04 +0000 (17:17 +0200)]
drm/i915: set default value for config->pixel_multiplier
This way we can simplify the code quite a bit.
Also add a WARN in the sdvo code to complain about a bogus value
and kill the readout code in intel_ddi.c that Jesse sneaked in.
HW state readout for the pixel multiplier will work a bit differently
in the end.
v2: Rebase on top of the fdi pixel mutliplier handling fix.
Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 5 Jun 2013 18:55:29 +0000 (21:55 +0300)]
drm/i915: distinguish between error messages in DIDL initialization
Two exactly same error messages on different error paths makes debugging
difficult. Clarify the messages and distinguish them from each other.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 30 May 2013 13:04:25 +0000 (15:04 +0200)]
drm/i915: consolidate and tighten encoder cloning checks
Only lvds/tv did actually check for cloning or not, but many more
places should.
Notices because my ivb tried to enable both cpu edp and vga on the
first crtc - the resulting confusion between has_pch_encoder,
has_dp_encoder but not actually being a pch dp encoder resulting in
hilarity (hitting a BUG).
We _really_ need an igt to random-walk our modeset space more
exhaustively.
The bug seems to have been exposed due to a race in the hw load
detection support for VGA: Right after a hotplug VGA was still
detected as connected, but obviously reading the EDID wasn't possible
any more. Hence why restarting X a bit later fixed things. Due to the
1024x756 fallback resolution suddenly more outputs had the same
resolution.
On top of that SNA was confused with the possible_clones mask, trying
to clone outputs which cannot be cloned. That bug is now fixed with
sna: fixup up possible_clones kms->X impedance mismatch
v2: Kill intel_encoder_check_is_cloned, spotted by Paulo.
v3: Drop the now unused pipe param.
v4: Kill the stray printk Chris spotted.
v5: Elaborate on how the bug in userspace happened and why it was racy
to reproduce.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@vger.kernel.org Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 21 May 2013 15:01:50 +0000 (18:01 +0300)]
drm/i915: Fix DSPCLK_GATE_D for VLV
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 21 May 2013 15:01:49 +0000 (18:01 +0300)]
drm/i915: VLV doesn't have the ILK+ style LP watermark registers
The LP watermark registers don't exist on VLV, so don't touch them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 1 Jun 2013 15:16:23 +0000 (17:16 +0200)]
drm/i915: check for strange pfit pipe assignemnt on ivb/hsw
Panel fitters on ivb/hsw are not created equal since not all of them
support the new high-quality upscaling mode. To offset this the hw
allows us to freely assign the pfits to pipes.
Since our code currently doesn't support this we might fall over when
taking over firmware state. So check for this case and WARN about it.
We can then improve the code once we've hit this in the wild. Or once
we decide to support the improved upscale modes, though that requires
global arbitrage of modeset resources across crtcs.
v2: Check for IS_GEN7 instead of IS_IVB || IS_HSW as suggested by
Paulo in his review comment.
Suggested-by: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 1 Jun 2013 15:16:21 +0000 (17:16 +0200)]
drm/i915: store adjusted dotclock in adjusted_mode->clock
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3) Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 1 Jun 2013 15:16:19 +0000 (17:16 +0200)]
drm/i915: clear up the fdi dotclock semantics for M/N computation
We currently mutliply the link_bw of the fdi link with the pixel
multiplier, which is wrong: The FDI link doesn't suddenly grow more
bandwidth. In reality the pixel mutliplication only happens in the PCH,
before the pixels are fed into the port.
But since we our code treats the uses the target clock after pixels
are doubled (tripled, ...) already, we need to correct this.
Semantically it's clearer to divide the target clock to get the fdi
dotclock instead of multiplying the bw, so do that instead.
Note that the target clock is already multiplied by the same factor,
so the division will never loose accuracy for the M/N computation.
The lane computation otoh used the wrong value, we also need to feed
the fdi dotclock to that.
Split out on a request from Paulo Zanoni.
v2: Also fix the lane computation, it used the target clock to compute
the bw requirements, not the fdi dotclock (i.e. adjusted with the
pixel multiplier). Since sdvo only uses the pixel multiplier for
low-res modes (with a dotclock below 100MHz) we wouldn't ever have
rejected a bogus mode, but just used an inefficient fdi config.
v3: Amend the commit message to explain better what the change for the
fdi lane config computation is all about. Requested by Paulo.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 3 Jun 2013 18:56:24 +0000 (20:56 +0200)]
drm/i915: fold in IS_PNV checks from the split up find_dpll functions
Since I stand by my rule that splitting functions should only do an
exact copy, this is a follow-up patch.
Suggested-by: Paulo Zanoni <przanoni@gmail.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 3 Jun 2013 20:40:22 +0000 (22:40 +0200)]
drm/i915: move find_pll callback to dev_priv->display
Now that the DP madness is cleared out, this is all only per-platform.
So move it out from the intel clock limits structure.
While at it drop the intel prefix on the static functions, call the
vtable entry find_dpll (since it's for the display pll) and rip out
the now unnecessary forward declarations.
Note that the parameters of ->find_dpll are still unchanged, but they
eventually need to be moved over to just take in a pipe configuration.
But currently a lot of things are still missing from the pipe
configuration (reflock, output-specific dpll limits and preferences,
downclocked dotclock). So this will happen in a later step.
Note that intel_g4x_limit has a peculiar case where it selects
intel_limits_i9xx_sdvo as the limit. This is pretty bogus and also not
used since the only output types left are DP and native TV-out which
both use special pre-tuned dpll values.
v2: Re-add comment for the find_pll callback (requested by Paulo) and
elaborate on why the transformation is correct for g4x platforms (to
clarify a review question from Paulo). Double up on that by adding a
WARN as suggested by Paulo Zanoni on irc.
v3: Initialize limits to NULL since gcc is now unhappy.
v4: v2/3 will blow up with a NULL dereference in ->find_dpll for dp and
TV-out ports, spotted by Paulo on irc. So just give up on this madness for
now, and leave this to be fixed in a later patch.
v5: Since the ever-so-slight change for g4x might result in some dpll
parameter computation failing spuriously where before it didn't for
ports with preset dpll settings (DP & TV-out) override this. For
paranoia also do it in the ilk+ code.
Cc: Paulo Zanoni <przanoni@gmail.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 1 Jun 2013 15:16:17 +0000 (17:16 +0200)]
drm/i915: split out intel_pnv_find_best_PLL
Pineview is just different.
Also split out i9xx_clock from intel_clock and drop the now redundant
struct device * parameter.
Note that in this patch I kill an XXX comment about 100MHz clocks. I
couldn't figure out what this is about, and we don't seem to have any
bug reports about this either. I suspect that it's a remnant from when
the i9xx and ilk+ modeset code was all in the same file since ilk+
does indeed have a 100MHz clock. So I've just killed it to stop the
cargo-culting.
Reviewed-by: Paulo Zanoni <przanoni@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sun, 2 Jun 2013 11:26:24 +0000 (13:26 +0200)]
drm/i915: fix EDID/sink-based bpp clamping
Since this is run in the compute config stage we need to check
the new_ pointers, i.e the stage output routing, not the current
modeset layout. Also there was a little logic bug in properly skipping
connectors: The old code did not skip any unused connectors and so
clamped to whatever was left in there (usually 0 if that connector
hasn't seen a EDID 1.4 screen ever since boot-up).
This has been broken when moving the pipe bpp selection in
drm/i915: precompute pipe bpp before touching the hw
To avoid too much casting switch from drm_ to intel_ types.
Also add a bit of debug output to help reconstructing what's going
on.
v2: Try to clarify this a bit:
- s/pipe_config_set_bpp/compute_baseline_pipe_bpp/ to make it clearer
at which stage this function is run. Also add a comment about what
it does.
- Extract the sink clamping into it's own function.
v3: Actually make it compile.
v4: Split out all the prep refactoring to make the bugfix stick out
really badly. Also elaborate a bit in the commit message about the
nature of the bugfix.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sun, 2 Jun 2013 11:26:23 +0000 (13:26 +0200)]
drm/i915: refactor sink bpp clamping
As a prep work to fix it up:
- Use intel_connector instead of drm_connector to avoid too much
upcasting in the bugfix patch.
- Extract the connector bpp clamping from the loop-over-connectors
logic.
- Bikeshed function names (to make it clearer that
acompute_baseline_pipe_bpp runs in the compute stage of the modeset
sequence) and add a comment to make it clearer what it does.
No functional change in this patch.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sun, 2 Jun 2013 15:23:01 +0000 (17:23 +0200)]
drm/i915: optimize vblank waits in set_base_atomic
We only need to do them if the pipe is actually running and if the
framebuffers have changed. Removes two "wait for vblank timed out"
messages when doing a suspend/resume cycle on my i855gm.
v2: s/to_intel_ctrc(crtc)/intel_crtc/ spotted by Chris.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
People don't like typedefs these days. Eliminate their use from intel_fb.c.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 31 May 2013 17:07:05 +0000 (20:07 +0300)]
drm/i915: Use container_of() in the fbdev code
Use container_of() instead of a cast to get struct intel_fbdev
from struct drm_fb_helper.
Also populate the fb_info->par correctly with the drm_fb_helper pointer
instead of the intel_fbdev pointer.
There's no actual functional change since the drm_fb_helper happens to
be the first member inside intel_fbdev.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Mon, 13 May 2013 13:32:13 +0000 (16:32 +0300)]
drm/i915: remove i915_hangcheck_hung
Rework of per ring hangcheck made this obsolete.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Thu, 30 May 2013 06:04:29 +0000 (09:04 +0300)]
drm/i915: detect hang using per ring hangcheck_score
Keep track of ring seqno progress and if there are no
progress detected, declare hang. Use actual head (acthd)
to distinguish between ring stuck and batchbuffer looping
situation. Stuck ring will be kicked to trigger progress.
This commit adds a hard limit for batchbuffer completion time.
If batchbuffer completion time is more than 4.5 seconds,
the gpu will be declared hung.
Review comment from Ben which nicely clarifies the semantic change:
"Maybe I'm just stating the functional changes of the patch, but in case
they were unintended here is what I see as potential issues:
1. "If ring B is waiting on ring A via semaphore, and ring A is making
progress, albeit slowly - the hangcheck will fire. The check will
determine that A is moving, however ring B will appear hung because
the ACTHD doesn't move. I honestly can't say if that's actually a
realistic problem to hit it probably implies the timeout value is too
low.
2. "There's also another corner case on the kick. If the seqno = 2
(though not stuck), and on the 3rd hangcheck, the ring is stuck, and
we try to kick it... we don't actually try to find out if the kick
helped"
v2: use atchd to detect stuck ring from loop (Ben Widawsky)
v3: Use acthd to check when ring needs kicking.
Declare hang on third time in order to give time for
kick_ring to take effect.
v4: Update commit msg
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Paste in Ben's review comment.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 31 May 2013 18:28:48 +0000 (11:28 -0700)]
drm/i915: Rename the gtt_list to global_list
Since it will be used for the global bound/unbound list with full PPGTT,
this helps clarify things for upcoming code rework.
Recommended-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 31 May 2013 18:28:47 +0000 (11:28 -0700)]
drm/i915: unpin pages at unbind
If we properly keep track of the pages_pin_count, then when we later add
multiple address spaces, the put_pages doesn't need any special checks
to be able to perform it's job.
CC: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Rebased on top of the fix for stolen memory pinning.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 31 May 2013 21:46:20 +0000 (14:46 -0700)]
drm/i915: Unpin stolen pages
The way the stolen handling works is we take a pin on the backing pages,
but we never actually get a reference to the bo. On freeing objects
allocated with stolen memory, the final unref will end up freeing the
object with pinned pages count left. To enable an assertion to catch
bugs in this code path, this patch cleans up that remaining pin.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Fri, 31 May 2013 18:28:45 +0000 (11:28 -0700)]
drm/i915: Demote unknown param to DRM_DEBUG
It's not terribly interesting to know that a parameter doesn't exist,
and it can get in the way of interesting messages, especially with the
staggered VECS merging as we've done.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 31 May 2013 19:33:23 +0000 (16:33 -0300)]
drm/i915: add enable_ips module option
IPS is still enabled by default. Feature requested by the power
management team.
This should also help testing the feature on some early pre-production
hardware where there were relationship problems between IPS and PSR.
v2: Rebase on top of the newest IPS implementation.
v3: Check i915_enable_ips at compute_config, not supports_ips, so the
kernel parameter will be ignored at haswell_get_pipe_config.
Requested-by: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 31 May 2013 19:33:22 +0000 (16:33 -0300)]
drm/i915: implement IPS feature
Intermediate Pixel Storage is a feature that should reduce the number
of times the display engine wakes up memory to read pixels, so it
should allow deeper PC states. IPS can only be enabled on ULT pipe A
with 8:8:8 pipe pixel formats.
With eDP 1920x1080 and correct watermarks but without FBC this moves
my PC7 residency from 2.5% to around 38%.
v2: - It's tied to pipe A, not port A
- Add pipe_config support (Chris)
- Add some assertions (Chris)
- Rebase against latest dinq
v3: - Don't ever set ips_enabled to false (Daniel)
- Only check for ips_enabled at hsw_disable_ips (Daniel)
v4: - Add hsw_compute_ips_config (Daniel)
- Use the new dump_pipe_config (Daniel)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 31 May 2013 15:49:17 +0000 (17:49 +0200)]
drm/i915: fix up the edp power well check
Now that we track the cpu transcoder we need accurately in the pipe
config we can finally fix up the transcoder check. With the current
code eDP on port D will be broken since we'd errornously cut the
power.
v2:
- Kill the now outdated comment (Paulo)
- Add the missing crtc->base.enabled check and consolidate it (Paulo)
- Smash all checks together, looks neater that way.
v3: Kill the unused encoder variable.
Cc: Takashi Iwai <tiwai@suse.de> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / linux-beck.git / log