Hans de Goede [Fri, 1 Aug 2014 07:16:47 +0000 (09:16 +0200)]
sunxi-common.h: Remove dead #ifdef CONFIG_CMD_NET code block
We undef CONFIG_CMD_NET at line 167, and there is nothing re-defining it
between line 167 and the #ifdef CONFIG_CMD_NET, so remove this effectively
dead block.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Simon Glass [Mon, 7 Jul 2014 16:16:38 +0000 (10:16 -0600)]
exynos: spi: Fix calculation of SPI transaction start time
The SPI transaction delay is supposed to be measured from the end of one
transaction to the start of the next. The code does not work that way, so
fix it.
Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Simon Glass [Fri, 11 Jul 2014 04:23:26 +0000 (22:23 -0600)]
arm: Set up global data before board_init_f()
At present arm defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f(). However it is
actually set up before this, it just isn't zeroed.
If we zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.
Make this change (on arm32 only) to simplify the init process. I
don't have the ability to test aarch64 yet.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Tom Rini <trini@ti.com>
When CONFIG_WATCHDOG is defined the board initialization just performs
a WATCHDOG_RESET, an initialization of the watchdog is not done.
This has been modified fot the MPC85xx, the board initialization calls
its watchdog initialitzation allowing for full watchdog configuration
very early in the boot phase.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
For e500mc cores the watchdog timer period has to be set by means of a
6bit value, that defines the bit of the timebase counter used to signal
a watchdog timer exception on its 0 to 1 transition.
The macro used to set the watchdog period TCR_WP, was redefined for e500mc
to support 6 WP setting.
The parameter (x) given to the macro specifies the prescaling factor of
the time base clock (fTB):
watchdog_period = 1/fTB * 2^x
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
Chin Liang See [Tue, 10 Jun 2014 06:26:52 +0000 (01:26 -0500)]
mmc/dw_mmc: Fix clock divider calculation error for bypass mode
To fix the clock divider calculation error when the controller
clock same as the operating frequency. This is known as bypass
mode. In this mode, the divider should be 0.
Lubomir Rintel [Tue, 10 Jun 2014 18:46:43 +0000 (20:46 +0200)]
bcm2835_sdhci: Add SDHCI_QUIRK_NO_HISPD_BIT flag
Seems like the controller doesn't support the flag. None of the hi-speed cards
I've tried could be read, while they successfully worked with the quirk enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Hans de Goede [Tue, 29 Jul 2014 16:29:27 +0000 (18:29 +0200)]
sun7i: Add bananapi board
The Banana Pi is an A20 based development board using Raspberry Pi compatible
IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi
and stereo audio out + various expansion headers:
http://www.lemaker.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Marc Zyngier [Fri, 18 Jul 2014 20:06:39 +0000 (21:06 +0100)]
sunxi: HYP/non-sec: configure CNTFRQ on all CPUs
CNTFRQ needs to be properly configured on all CPUs. Otherwise,
virtual machines hoping to find valuable information on secondary
CPUs will be disapointed...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 27 Jul 2014 20:29:38 +0000 (22:29 +0200)]
sun7i: Add support for a number of new sun7i boards
Add support for boards which I own and which already have a dts file in the
upstream kernel.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 27 Jul 2014 15:55:43 +0000 (17:55 +0200)]
sun5i: Add support for a number of new sun5i boards
Add support for boards which I own and which already have a dts file in the
upstream kernel.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 26 Jul 2014 14:51:08 +0000 (16:51 +0200)]
sun4i: Add support for a number of new sun4i boards
Add support for boards which I own and which already have a dts file in the
upstream kernel.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Roman Byshko [Thu, 24 Jul 2014 20:54:24 +0000 (22:54 +0200)]
sun7i: cubietruck: enable USB EHCI
Cubietruck has two USB host controllers. This makes them
usable by enabling the EHCI driver for them.
Signed-off-by: Roman Byshko <rbyshko@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Also enable ehci for Cubietruck_FEL] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Roman Byshko [Thu, 24 Jul 2014 20:54:23 +0000 (22:54 +0200)]
sun7i: add USB EHCI settings
Specific USB EHCI settings to be set for sun7i if
CONFIG_USB_EHCI is enabled.
Signed-off-by: Roman Byshko <rbyshko@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Use SUNXI_GPH macro for SUNXI_USB_VBUS#_GPIO]
[hdegoede@redhat.com: Add #ifndef SUNXI_USB_VBUS#_GPIO to allow override of
the default pins from boards.cfg] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Roman Byshko [Thu, 24 Jul 2014 20:54:22 +0000 (22:54 +0200)]
sunxi: add general USB settings
General configuration settings to be set if CONFIG_USB_EHCI
is enabled for an Allwinner aka sunxi SoC.
Signed-off-by: Roman Byshko <rbyshko@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Roman Byshko [Thu, 24 Jul 2014 20:54:20 +0000 (22:54 +0200)]
sunxi: add defines to control USB Host clocks/resets
The commit adds three defines which will be used in
the EHCI driver to enable USB clock and assert
reset controllers of the corresponding PHYs.
Signed-off-by: Roman Byshko <rbyshko@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ian Campbell [Fri, 18 Jul 2014 19:38:41 +0000 (20:38 +0100)]
ahci: provide sunxi SATA driver using AHCI platform framework
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
- Use "make <board>_defconfig" instead of "make <board>_config".
- Invoke tools/genboardscfg.py to generate boards.cfg when it is
missing.
- Show "Building ${BOARD_NAME} board..." message.
(Prior to Kconfig, instead, mkconfig script displayed
"Configuring for ${BOARD_NAME} board..." but it was removed.)
Without this message, we cannot know which board is currently
being built.
- Do not show "# configuration written to .config".
This message is useless and just annoying for MAKEALL.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
The old configuration script is no longer necessary.
Nor is boards.cfg a primary database.
We can generate it with the genboardscfg.py tool
based on the latest Kconfig, defconfig and MAINTAINERS.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Now the primary data for each board is in Kconfig, defconfig and
MAINTAINERS.
It is true boards.cfg is needed for MAKEALL and buildman and might be
useful to brouse all the supported boards in a single database.
But it would be painful to maintain the boards.cfg in sync.
So, this is the solution.
Add a tool to generate the equivalent boards.cfg file based on
the latest Kconfig, defconfig and MAINTAINERS.
We can keep all the functions of MAKEALL and buildman with it.
The best thing would be to change MAKEALL and buildman for not
depending on boards.cfg in the future, but it would take some time.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
This commit enables Kconfig.
Going forward, we use Kconfig for the board configuration.
mkconfig will never be used. Nor will include/config.mk be generated.
Kconfig must be adjusted for U-Boot because our situation is
a little more complicated than Linux Kernel.
We have to generate multiple boot images (Normal, SPL, TPL)
from one source tree.
Each image needs its own configuration input.
Usage:
Run "make <board>_defconfig" to do the board configuration.
It will create the .config file and additionally spl/.config, tpl/.config
if SPL, TPL is enabled, respectively.
You can use "make config", "make menuconfig" etc. to create
a new .config or modify the existing one.
Use "make spl/config", "make spl/menuconfig" etc. for spl/.config
and do likewise for tpl/.config file.
The generic syntax of configuration targets for SPL, TPL is:
<target_image>/<config_command>
Here, <target_image> is either 'spl' or 'tpl'
<config_command> is 'config', 'menuconfig', 'xconfig', etc.
When the configuration is done, run "make".
(Or "make <board>_defconfig all" will do the configuration and build
in one time.)
For futher information of how Kconfig works in U-Boot,
please read the comment block of scripts/multiconfig.py.
By the way, there is another item worth remarking here:
coexistence of Kconfig and board herder files.
Prior to Kconfig, we used C headers to define a set of configs.
We expect a very long term to migrate from C headers to Kconfig.
Two different infractructure must coexist in the interim.
In our former configuration scheme, include/autoconf.mk was generated
for use in makefiles.
It is still generated under include/, spl/include/, tpl/include/ directory
for the Normal, SPL, TPL image, respectively.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
We are about to switch to Kconfig in the next commit.
But there are something to get done beforehand.
In Kconfig, include/generated/autoconf.h defines boolean
CONFIG macros as 1.
CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1.
Otherwise, when switching to Kconfig, the build log
would be sprinkled with warning messages like this:
warning: "CONFIG_SPL" redefined [enabled by default]
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Since the command name 'make' may not be GNU Make on some platforms
such as FreeBSD, buildman should call scripts/show-gnu-make to get
the command name for GNU MAKE (and error out if it is not found).
Since the command name 'make' may not be GNU Make on some platforms
such as FreeBSD, MAKEALL should call scripts/show-gnu-make to get
the command name for GNU MAKE (and error out if it is not found).
The GNU Make should be searched after parsing options because we want
to allow "MAKEALL -h" even if GNU Make is missing on the system.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Ma Haijun [Sat, 12 Jul 2014 13:24:06 +0000 (14:24 +0100)]
ARM: convert arch_fixup_memory_node to a generic FDT fixup function
Some architecture needs extra device tree setup. Instead of adding
yet another hook, convert arch_fixup_memory_node to be a generic
FDT fixup function.
[maz: collapsed 3 patches into one, rewrote commit message]
Signed-off-by: Ma Haijun <mahaijuns@gmail.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Marc Zyngier [Sat, 12 Jul 2014 13:24:04 +0000 (14:24 +0100)]
ARM: HYP/non-sec: add generic ARMv7 PSCI code
Implement core support for PSCI. As this is generic code, it doesn't
implement anything really useful (all the functions are returning
Not Implemented).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Marc Zyngier [Sat, 12 Jul 2014 13:24:03 +0000 (14:24 +0100)]
ARM: HYP/non-sec: allow relocation to secure RAM
The current non-sec switching code suffers from one major issue:
it cannot run in secure RAM, as a large part of u-boot still needs
to be run while we're switched to non-secure.
This patch reworks the whole HYP/non-secure strategy by:
- making sure the secure code is the *last* thing u-boot executes
before entering the payload
- performing an exception return from secure mode directly into
the payload
- allowing the code to be dynamically relocated to secure RAM
before switching to non-secure.
This involves quite a bit of horrible code, specially as u-boot
relocation is quite primitive.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Marc Zyngier [Sat, 12 Jul 2014 13:24:00 +0000 (14:24 +0100)]
ARM: non-sec: reset CNTVOFF to zero
Before switching to non-secure, make sure that CNTVOFF is set
to zero on all CPUs. Otherwise, kernel running in non-secure
without HYP enabled (hence using virtual timers) may observe
timers that are not synchronized, effectively seeing time
going backward...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Simon Glass [Mon, 14 Jul 2014 23:51:03 +0000 (17:51 -0600)]
buildman: Support in-tree builds
At present buildman always builds out-of-tree, that is it uses a separate
output directory from the source directory. Normally this is what you want,
but it is important that in-tree builds work also. Some Makefile changes may
break this.
Add a -i option to tell buildman to use in-tree builds, so that it is easy
to test this feature.
Simon Glass [Mon, 14 Jul 2014 23:51:02 +0000 (17:51 -0600)]
buildman: Add -C option to force a reconfigure for each commit
Normally buildman wil try to configure U-Boot for a particular board on the
first commit that it builds in a series. Subsequent commits are built
without reconfiguring which normally works. Where it doesn't, buildman
automatically reconfigures and retries.
To fully emulate the way MAKEALL works, we should have an option to disable
this optimisation.
Add a -C option to cause buildman to always reconfigure on each commit.
ARM: omap: move board specific NAND configs out from ti_armv7_common.h
This patch moves some board specific NAND configs:
- FROM: generic config file 'ti_armv7_common.h'
- TO: individual board config files using these configs.
So that each board can independently set the value as per its design.
Following configs are affected in this patch:
CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand>
CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon>
CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon>
CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon>
This patch also updates documentation for few of above NAND configs.
ARM: omap: clean redundant PISMO_xx macros used in OMAP3
PISMO_xx macros were used to define 'Platform Independent Storage MOdule'
related GPMC configurations. This patch
- Replaces these OMAP3 specific macros with generic CONFIG_xx macros as provided
by current u-boot infrastructure.
- Removes unused redundant macros, which are no longer required after
merging of common platform code in following commit
commit a0a37183bd75e74608bc78c8d0e2a34454f95a91
ARM: omap: merge GPMC initialization code for all platform
1) NAND device are not directly memory-mapped to CPU address-space, they are
indirectly accessed via following GPMC registers:
- GPMC_NAND_COMMAND_x
- GPMC_NAND_ADDRESS_x
- GPMC_NAND_DATA_x
Therefore from CPU's point of view, NAND address-map can be limited to just
above register addresses. But GPMC chip-select address-map can be configured
in granularity of 16MB only.
So this patch uses GPMC_SIZE_16M for all NAND devices.
2) NOR device are directly memory-mapped to CPU address-space, so its
address-map size depends on actual addressable region in NOR FLASH device.
So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map
size configuration.
The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5
ES 1.0 devices. The current revision check erroneously implements this
on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance)
infact causes an asynchronous abort and ends up masking it in CPSR,
only to be uncovered once the kernel switches to userspace.
projects / karo-tx-uboot.git / log