This implements an 8192eu specific enable_rf() function. The 8192eu is
not a combo device, so no need for doing the BT specific bits needed
by the 8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8xxxu: Fix OOPS if user tries to add device via /sys
This driver relies on driver_info in struct usb_device_id, so allowing
adding a device via /sys/bus/usb/drivers/rtl8xxxu/new_id will cause a
NULL pointer dereference.
Set .no_dynamic_id = 1 to disable hot add of USB IDs.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Thu, 14 Apr 2016 20:37:07 +0000 (16:37 -0400)]
rtl8xxxu: fix uninitialized return value in ret
several functions are not initializing a return status in ret
resulting in garbage to be returned instead of 0 for success.
Currently, the calls to these functions are not checking the
return, however, it seems prudent to return the correct status
in case they are to be checked at a later date.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This dongle was tested successfully by Andrea Merello
Reported-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8xxxu: Split rtl8xxxu_init_phy_bb() into device specific functions
This reduces the if () clutter. Longer term it probably makes sense to
split this between gen1 (8723au/8188cu/8192cu) and gen2
(8192eu/8723bu) devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8xxxu: byteswap the entire RX descriptor for 24 byte RX descriptors
This shouldn't affect little endian system, but may have prevented the
driver working on big endian systems for devices with the larger 24
byte RX descriptors.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The vendor driver does not set REG_PBP on 8192eu. Whether this is due
to the device not supporting it or simply an oversight in the vendor
driver is not clear.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8xxxu: Reorg more code to match the flow of the 8192eu vendor driver
This further reorganizes the init code flow to match that of the
8192eu vendor driver. This helps diffing the register write log
against that of the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Andreas Fenkart [Thu, 10 Mar 2016 08:44:11 +0000 (09:44 +0100)]
mwifiex: make mwifiex_insert_cmd_to_free_q local static
after factoring out mwifiex_cancel_pending_scan_cmd
the function is not called outside of cmdevt file
moved function to head of file to avoid forward declaration,
also moved mwifiex_recycle_cmd_node since they are very similar
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Andreas Fenkart [Thu, 10 Mar 2016 08:44:10 +0000 (09:44 +0100)]
mwifiex: factor out mwifiex_cancel_pending_scan_cmd
Releasing the scan_pending lock in mwifiex_check_next_scan_command
introduces a short window where pending scan commands can be removed
or added before removing them all in mwifiex_cancel_pending_scan_cmd.
I think this is safe, since the worst thing to happen is that a
pending scan cmd is removed by the command handler. Adding new scan
commands is not possible while one is pending, see scan_processing flag.
Since all commands are removed from the queue anyway, we don't care if
some commands are removed by a different code path earlier, the final
state remains the same.
I assume, that the critical section needed for the check has been
extended over clearing the pending scan queue out of convenience. The
lock was already held and releasing it and grab it again was just
more work. It doesn't seem to be necessary because of concurrency.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Andreas Fenkart [Thu, 10 Mar 2016 08:44:09 +0000 (09:44 +0100)]
mwifiex: scan: replace pointer arithmetic with array access
improves readability
Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Andreas Fenkart [Thu, 10 Mar 2016 08:44:07 +0000 (09:44 +0100)]
mwifiex: scan: simplify ternary operators using gnu extension
"x ? x : y" can be simplified as "x ? : y"
https://gcc.gnu.org/onlinedocs/gcc/Conditionals.html#Conditionals
Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During system suspend, there is a kernel WARNING issued if there
is a pending command present. By marking the wait queue disabled
after calling the command completion routine fixes it.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IEEE80211_CHAN_NO_HT40PLUS and IEEE80211_CHAN_NO_HT40PLUS channel
flags tell if HT40 operation is allowed on a channel or not.
This patch ensures ht_capability information is modified
accordingly so that we don't end up creating a HT40 connection
when it's not allowed for current regulatory domain.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Mon, 11 Apr 2016 14:52:40 +0000 (07:52 -0700)]
mwifiex: do not wait on semaphore during card removal
Host hang is observed if card is removed before firmware download
gets completed. In this case, firmware will be failed to download and
adapter structure gets freed.
In other thread, mwifiex_remove_card() waits on semaphore until the
firmware download fails. This wait is not necessary and may result in
invalid adapter access.
This patch uses down_trylock to return immediately so that hang issue
won't occur.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac: create common function for handling brcmf_proto_hdrpull()
In receive path brcmf_proto_hdrpull() needs to be called and handled
similar in brcmf_rx_frame() and brcmf_rx_event(). Move that duplicated
code in separate function.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move event handling out of brcmf_netif_rx() avoiding the need
to pass a flag. This flag is only ever true for USB hosts as
other interface use separate brcmf_rx_event() function.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Franky Lin [Mon, 11 Apr 2016 09:35:25 +0000 (11:35 +0200)]
brcmfmac: screening firmware event packet
Firmware uses asynchronized events as a communication method to the
host. The event packets are marked as ETH_P_LINK_CTL protocol type. For
SDIO and PCIe bus, this kind of packets are delivered through virtual
event channel not data channel. This patch adds a screening logic to
make sure the event handler only processes the events coming from the
correct channel.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When p2p connection setup is performed without having ever done an
escan a null pointer exception can occur. This is because the ifp
to abort scanning is taken from escan struct while it was never
initialized. Fix this by using the primary ifp for scan abort. The
abort should still be performed and all scan related commands are
performed on primary ifp.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac: insert default boardrev in nvram data if missing
Some nvram files/stores come without the boardrev information,
but firmware requires this to be set. When not found in nvram then
add a default boardrev string to the nvram data.
Reported-by: Rafal Milecki <zajec5@gmail.com> Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <franky.lin@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer firmwares require the usage of the wowl wakeind struct as size
for the iovar to clear the wake indicators. Older firmwares do not
care, so change the used size.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the event_msgs iovar is set an array is used to configure the
enabled events. This arrays needs to nulled before configuring
otherwise unhandled events will be enabled. This solves a problem
where in case of wowl the host got woken by an incorrectly enabled
event.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8xxxu: Set correct interrupt masking registers on 8192eu
Set HIMR[01] on 8192eu instead of HISR/HIMR. It's not obvious this
really matters for USB devices, but this matches the register writes
performed by the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sergei Shtylyov [Sun, 10 Apr 2016 20:55:15 +0000 (23:55 +0300)]
ravb: make ravb_ptp_interrupt() *void*
When we have the ISS.CGIS bit set, we already know that gPTP interrupt has
happened, so an extra GIS register check at the end of ravb_ptp_interrupt()
seems superfluous. We can model the gPTP interrupt handler like all other
dedicated interrupt handlers in the driver and make it *void*.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for the following via ethtool:
- UDP configuration of RSS based on 2-tuple/4-tuple.
- RSS hash key.
- RSS indirection table.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the required API for passing RSS-related configuration from qede.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Inbox drivers don't need versioning scheme in order to guarantee
compatibility, as both qed and qede are compiled from same codebase.
Signed-off-by: Rahul Verma <rahul.verma@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_isr1() and bcmgenet_isr0() run in hard irq context,
we do not need to block irq again.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 9 Apr 2016 05:06:40 +0000 (22:06 -0700)]
net: bcmgenet: use napi_complete_done()
By using napi_complete_done(), we allow fine tuning
of /sys/class/net/ethX/gro_flush_timeout for higher GRO aggregation
efficiency for a Gbit NIC.
Check commit 24d2e4a50737 ("tg3: use napi_complete_done()") for details.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Petri Gynther <pgynther@google.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 14 Apr 2016 03:04:44 +0000 (23:04 -0400)]
Merge branch 'sctp-delayed-wakeups'
Marcelo Ricardo Leitner says:
====================
sctp: delay calls to sk_data_ready() as much as possible
1st patch is a preparation for the 2nd. The idea is to not call
->sk_data_ready() for every data chunk processed while processing
packets but only once before releasing the socket.
v2: patchset re-checked, small changelog fixes
v3: on patch 2, make use of local vars to make it more readable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: delay calls to sk_data_ready() as much as possible
Currently processing of multiple chunks in a single SCTP packet leads to
multiple calls to sk_data_ready, causing multiple wake up signals which
are costy and doesn't make it wake up any faster.
With this patch it will note that the wake up is pending and will do it
before leaving the state machine interpreter, latest place possible to
do it realiably and cleanly.
Note that sk_data_ready events are not dependent on asocs, unlike waking
up writers.
v2: series re-checked
v3: use local vars to cleanup the code, suggested by Jakub Sitnicki Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: compress bit-wide flags to a bitfield on sctp_sock
It wastes space and gets worse as we add new flags, so convert bit-wide
flags to a bitfield.
Currently it already saves 4 bytes in sctp_sock, which are left as holes
in it for now. The whole struct needs packing, which should be done in
another patch.
Note that do_auto_asconf cannot be merged, as explained in the comment
before it.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/jme.c: Deinline jme_reset_mac_processor, save 2816 bytes
This function compiles to 895 bytes of machine code.
Clearly, this isn't a time-critical function.
For one, it has a number of udelay(1) calls.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> CC: David S. Miller <davem@davemloft.net> CC: linux-kernel@vger.kernel.org CC: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 14 Apr 2016 02:42:33 +0000 (22:42 -0400)]
Merge branch 'bridge-sysfs-rtnl-notifications'
Xin Long says:
====================
bridge: support sending rntl info when we set attributes through sysfs/ioctl
This patchset is used to support sending rntl info to user in some places,
and ensure that whenever those attributes change internally or from sysfs,
that a netlink notification is sent out to listeners.
It also make some adjustment in bridge sysfs so that we can implement this
easily.
I've done some tests on this patchset, like:
[br_sysfs]
1. change all the attribute values of br or brif:
$ echo $value > /sys/class/net/br0/bridge/{*}
$ echo $value > /sys/class/net/br0/brif/eth1/{*}
2. meanwhile, on another terminal to observe the msg:
$ bridge monitor
[br_ioctl]
1. in bridge-utils package, do some changes in br_set, let brctl command
use ioctl to set attribute:
if ((ret = set_sysfs(path, value)) < 0) { -->
if (1) {
$ brctl set*
2. meanwhile, on another terminal to observe the msg:
$ bridge monitor
This test covers all the attributes that brctl and sysfs support to set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 8 Apr 2016 16:03:33 +0000 (00:03 +0800)]
bridge: a netlink notification should be sent when those attributes are changed by ioctl
Now when we change the attributes of bridge or br_port by netlink,
a relevant netlink notification will be sent, but if we change them
by ioctl or sysfs, no notification will be sent.
We should ensure that whenever those attributes change internally or from
sysfs/ioctl, that a netlink notification is sent out to listeners.
Also, NetworkManager will use this in the future to listen for out-of-band
bridge master attribute updates and incorporate them into the runtime
configuration.
This patch is used for ioctl.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 8 Apr 2016 16:03:32 +0000 (00:03 +0800)]
bridge: a netlink notification should be sent when those attributes are changed by br_sysfs_if
Now when we change the attributes of bridge or br_port by netlink,
a relevant netlink notification will be sent, but if we change them
by ioctl or sysfs, no notification will be sent.
We should ensure that whenever those attributes change internally or from
sysfs/ioctl, that a netlink notification is sent out to listeners.
Also, NetworkManager will use this in the future to listen for out-of-band
bridge master attribute updates and incorporate them into the runtime
configuration.
This patch is used for br_sysfs_if, and we also move br_ifinfo_notify out
of store_flag.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 8 Apr 2016 16:03:31 +0000 (00:03 +0800)]
bridge: a netlink notification should be sent when those attributes are changed by br_sysfs_br
Now when we change the attributes of bridge or br_port by netlink,
a relevant netlink notification will be sent, but if we change them
by ioctl or sysfs, no notification will be sent.
We should ensure that whenever those attributes change internally or from
sysfs/ioctl, that a netlink notification is sent out to listeners.
Also, NetworkManager will use this in the future to listen for out-of-band
bridge master attribute updates and incorporate them into the runtime
configuration.
This patch is used for br_sysfs_br. and we also need to remove some
rtnl_trylock in old functions so that we can call it in a common one.
For group_addr_store, we cannot make it use store_bridge_parm, because
it's not a string-to-long convert, we will add notification on it
individually.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log