Thomas Graf [Fri, 3 Sep 2010 02:59:14 +0000 (02:59 +0000)]
ipv6: add special mode accept_ra=2 to accept RA while configured as router
The current IPv6 behavior is to not accept router advertisements while
forwarding, i.e. configured as router.
This does make sense, a router is typically not supposed to be auto
configured. However there are exceptions and we should allow the
current behavior to be overwritten.
Therefore this patch enables the user to overrule the "if forwarding
enabled then don't listen to RAs" rule by setting accept_ra to the
special value of 2.
An alternative would be to ignore the forwarding switch alltogether
and solely accept RAs based on the value of accept_ra. However, I
found that if not intended, accepting RAs as a router can lead to
strange unwanted behavior therefore we it seems wise to only do so
if the user explicitely asks for this behavior.
Signed-off-by: Thomas Graf <tgraf@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 2 Sep 2010 03:53:46 +0000 (03:53 +0000)]
net: dev_add_pack() & __dev_remove_pack() changes
Add a small helper ptype_head() to get the head to manipulate
dev_add_pack() & __dev_remove_pack() can use a spinlock without
blocking BH, since softirq use RCU, and these functions are run from
process context only.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211: only cancel software-based scans on suspend
Otherwise the hardware scan handler could access an invalid scan request
structure. The driver should cancel any pending hardware scans during
the suspend process anyway, so also add a warning if the hardware scan
is still pending when the device resumes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Dumazet [Wed, 1 Sep 2010 05:25:10 +0000 (05:25 +0000)]
net: skbuff.c cleanup
(skb->data - skb->head) can be changed by skb_headroom(skb)
Remove some uses of NET_SKBUFF_DATA_USES_OFFSET, using
(skb_end_pointer(skb) - skb->head) or
(skb_tail_pointer(skb) - skb->head) : compiler does the right thing,
and this is more readable for us ;)
(struct skb_shared_info *) casts in pskb_expand_head() to help memcpy()
to use aligned moves.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 31 Aug 2010 18:25:32 +0000 (18:25 +0000)]
skge: add GRO support
- napi_gro_flush() is exported from net/core/dev.c, to avoid
an irq_save/irq_restore in the packet receive path.
- use napi_gro_receive() instead of netif_receive_skb()
- use napi_gro_flush() before calling __napi_complete()
- turn on NETIF_F_GRO by default
- Tested on a Marvell 88E8001 Gigabit NIC
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 31 Aug 2010 07:44:00 +0000 (07:44 +0000)]
drivers/net/can/mscan/mpc5xxx_can.c: Add of_node_put to avoid memory leak
Add a call to of_node_put in the error handling code following a call to
of_find_matching_node.
This patch also moves the existing call to of_node_put after the call to
iounmap in the error handling code, to make it possible to jump to
of_node_put without doing iounmap. These appear to be disjoint operations,
so the ordering doesn't matter.
This patch furthermore changes the -ENODEV result in the error handling
code for of_find_matching_node to a return of 0, as found in the error
handling code for of_iomap, because the return type of the function is
unsigned.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
|of_find_node_by_type
|of_find_node_with_property
|of_find_matching_node
|of_parse_phandle
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
(
E2 = x;
|
of_node_put(x);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Aug 2010 11:07:25 +0000 (11:07 +0000)]
net: tunnels should use rcu_dereference
tunnel4_handlers, tunnel64_handlers, tunnel6_handlers and
tunnel46_handlers are protected by RCU, but we dont use appropriate rcu
primitives to scan them. rcu_lock() is already held by caller.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Change 848xx LED configuration according to the new microcode (Boards
were shipped with only with the new microcode)
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Remove unneeded setting of XAUI low power to BCM8727
Remove unneeded setting of XAUI low power to BCM8727. This was required
only in older microcode which is not in the field.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Change BCM848xx configuration according to IEEE
Change BCM848xx behavior to fit IEEE such that setting 10Mb/100Mb will
use force speed, and setting 1Gb/10Gb will use auto-negotiation with the
specific speed advertised
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reset link before any new link settings to avoid potential link issue
caused by previous link settings
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Fix potential link issue In BCM8727 based boards
In BCM8727 based boards, setting default 10G link speed after link was
set to 1G may lead to link down issue. The problem was setting the right
value, but to the wrong registers
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Fix potential link issue of BCM8073/BCM8727
Fix potential link issue caused by insufficient delay time during SPIROM
load of BCM8073/BCM8727
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hypervisor allows, two VM's interfaces to have same mac address.
These VM's interfaces get differentiate with Vlan tag.
This patch add support to learn and configure mac+vlan filter on device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Device eswitch need to configure with VM's mac address.
Hypervisor doesn't provide any utility/callbacks to get VM's mac address.
Unicast mac address filter improves performance and also provide
packet loopback capability i.e communication between VM.
Above features is by default off, can be turned on with module parameter
'mac_learn'.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Tue, 31 Aug 2010 17:17:50 +0000 (17:17 +0000)]
qlcnic: fix mac override capability
o Rename mac_learning to mac_override
o Added check in set_mac to return error if mac override is disabled.
o Disabling mac_override only supported for Non priviledged functions.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Tue, 31 Aug 2010 17:17:49 +0000 (17:17 +0000)]
qlcnic: fix panic while using eth_hdr
o skb->mac_header is not set, so machine panics while using function eth_hdr.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Tue, 31 Aug 2010 17:17:48 +0000 (17:17 +0000)]
qlcnic: fix mac anti spoof policy
o Allow enabling/disabling mac anti spoof policy only for
Non privilege functions.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Tue, 31 Aug 2010 17:17:47 +0000 (17:17 +0000)]
qlcnic: fix for setting default eswitch config
o Default eswitch config was set, even before eswitch capabilty get detected.
As a result setting default config was getting fail.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Tue, 31 Aug 2010 17:17:46 +0000 (17:17 +0000)]
qlcnic: fix mac addr read
o Mac addr was read from flash for every fw reset
for Non-priviledge function.It should be read only once.
o Remove unnecessary get_mac_addr callback
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Tue, 31 Aug 2010 17:17:45 +0000 (17:17 +0000)]
qlcnic: add api version in reg dump
o ethtool reg version bumped to 2
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Sep 2010 03:56:48 +0000 (20:56 -0700)]
stmmac: Fix another build warning.
drivers/net/stmmac/dwmac100_core.c: In function 'dwmac100_dump_mac_regs':
drivers/net/stmmac/dwmac100_core.c:47: warning: cast from pointer to integer of different size
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 31 Aug 2010 07:40:16 +0000 (07:40 +0000)]
net: add a comment on netdev->last_rx
As some driver authors seem to reintroduce dev->last_rx use,
add a comment to strongly discourage this.
Since commit 6cf3f41e6c0 (bonding, net: Move last_rx update into bonding
recv logic), network drivers dont need to update last_rx themselves,
unless they use this field to implement a timeout.
Not updating last_rx helps not dirtying a cache line, improving
performance in SMP.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Mon, 30 Aug 2010 19:12:02 +0000 (15:12 -0400)]
mac80211: cancel scan in ieee80211_restart_hw if software scan pending
This function exists to clean-up after a hardware error or something
similar. The restart is accomplished using the same infrastructure used
to resume after a suspend. The suspend path cancels running scans, so
it seems appropriate to do that here as well for software-based scans.
If a hardware-based scan is pending, issue a warning message since this
indicates that the drivers has failed to clean-up after itself.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:15:51 +0000 (21:15 +0200)]
rt2x00: Cleanup rt2x00usb_watchdog_reset_tx
rt2x00usb_watchdog_reset_tx performs the same task
as rt2x00usb_kill_tx_queue, with the only difference
is that it waits for all entries to be returned to
the driver and for all frames the status has been
reported to mac80211.
We can easily split this task by calling rt2x00usb_kill_tx_queue,
sleep for a short period and invoke the TX status reporting
function. By adding the sleep() to the kill_entry we make sure
that even during shutdown we guarentee the entry has been killed when
the function returns. To make this work correctly the interrupt
handlers have to be updated to prevent checking for the RADIO_ENABLED
flag too early which prevents the ownership of the entry to be reset.
Additionally a check for the DEVICE_PRESENT flag is not required but
is nice to prevent race conditions when the device was unplugged.
Additionally rather then calling rt2x00usb_work_txdone() for
status reporting we let the driver perform the TX status reporting
first. If this is not sufficient then rt2x00usb_work_txdone() will
still be used to cleanup the mess.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:15:19 +0000 (21:15 +0200)]
rt2x00: Split watchdog check into a DMA and STATUS timeout
The watchdog for rt2800usb triggers frequently causing all URB's
to be canceled often enough to interrupt the normal TX flow.
More research indicated that not the URB upload to the USB host
were hanging, but instead the TX status reports.
To correctly detect what is going on, we introduce Q_INDEX_DMA_DONE
which is an index counter between Q_INDEX_DONE and Q_INDEX and indicates
if the frame has been transfered to the device.
This also requires the rt2x00queue timeout functions to be updated
to differentiate between a DMA timeout (time between Q_INDEX and
Q_INDEX_DMA_DONE timeout) and a STATUS timeout (time between
Q_INDEX_DMA_DONE and Q_INDEX_DONE timeout)
All Q_INDEX_DMA_DONE code was taken from the RFC from
Helmut Schaa <helmut.schaa@googlemail.com> for the implementation
for watchdog for rt2800pci.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:14:56 +0000 (21:14 +0200)]
rt2x00: Correctly kill beacon queue
USB devices upload their beacon and then automatically send
it out every beacon interval. However when killing a TX queue
we only kill the URB and not the actual transmission of the beacon.
This will reset the Beacon register to prevent any beacons from
being transmitted.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:14:38 +0000 (21:14 +0200)]
rt2x00: Set PWR_PIN_CFG during initialization
Add PWR_PIN_CFG initialization for rt2800usb at the same point
as rt2800pci.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:14:15 +0000 (21:14 +0200)]
rt2x00: Don't set unicast/BSSID masks when clearning MAC or BSSID
When configuring the MAC_ADDR or MAC_BSSID with an empty address,
the UNICAST_TO_ME_MASK and BSS_ID_MASK must also be reset to prevent
invalid interpretation of the addresses.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:13:54 +0000 (21:13 +0200)]
rt2x00: Wakeup hardware before loading firmware
According to the legacy drivers the AUTOWAKEUP_CFG
register must be reset to 0 before loading the firmware.
Instead of during rt2800{pci,usb}_write_firmware it
must actually be done in rt2800_load_firmware() before
resetting the WPDMA_GLO_CFG and PWR_PIN_CFG registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:13:30 +0000 (21:13 +0200)]
rt2x00: Validate TX status results with current data entry
Instead of printing a warning when the PID, ACK, or WCID of
an entry don't match the TX status report, we should skip the
entry to search for the entry which actually does match
the TX status data.
This reduces the number of watchdog errors on the TX queues
for rt2800usb, and seems to improve the reliability of the
TX flow a bit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 30 Aug 2010 19:13:08 +0000 (21:13 +0200)]
rt2x00: Add rt2800_wait_csr_ready
Similar to rt2800_wait_wpdma_ready() we can add a
function to waiting until the CSR is ready. This
centralizes some additional code into rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 30 Aug 2010 19:12:47 +0000 (21:12 +0200)]
rt2x00: Update rt2800 comments regarding AMPDU and PACKET_ID in TXWI
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Variables containing queue ids are called qid everywhere else, hence
rename the queue field in txentry_desc to qid as well.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 28 Aug 2010 16:21:21 +0000 (18:21 +0200)]
ath9k: fix spurious MIC failure reports
According to the hardware documentation, the MIC failure bit is only
valid if the frame was decrypted using a valid TKIP key and is not a
fragment.
In some setups I've seen hardware-reported MIC failures on an AP that
was configured for CCMP only, so it's clear that additional checks are
necessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
here's the original message:
The queue stopping/waking functionality was broken in a way that could
cause huge latencies in TX transfers and even cause the TX to stall in the
right circumstances. Correct these problems.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 27 Aug 2010 19:22:00 +0000 (22:22 +0300)]
mac80211: Do not generate CQM events based on first Beacon frames
The signal strength value in a single RX frame is not that reliable,
so it is better to delay start of CQM events until there is a real
average signal strength from more than a single Beacon frame
available.
Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 27 Aug 2010 19:21:13 +0000 (22:21 +0300)]
mac80211: Fix signal strength average initialization for CQM events
The ave_beacon_signal value uses 1/16 dB unit and as such, must be
initialized with the signal level of the first Beacon frame multiplied
by 16. This fixes an issue where the initial CQM events are reported
incorrectly with a burst of events while the running average
approaches the correct value after the incorrect initialization. This
could cause user space -based roaming decision process to get quite
confused at the moment when we would like to go through authentication
and DHCP.
Cc: stable@kernel.org Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Tue, 31 Aug 2010 04:55:17 +0000 (21:55 -0700)]
stmmac: Fix build warnings.
In file included from drivers/net/stmmac/stmmac_ethtool.c:30:
drivers/net/stmmac/stmmac.h:111: warning: 'struct platform_device' declared inside parameter list
drivers/net/stmmac/stmmac.h:111: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/net/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
drivers/net/stmmac/stmmac_main.c:1744: warning: cast from pointer to integer of different size
In file included from drivers/net/stmmac/stmmac_mdio.c:31:
drivers/net/stmmac/stmmac.h:111: warning: 'struct platform_device' declared inside parameter list
drivers/net/stmmac/stmmac.h:111: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/net/stmmac/dwmac1000_core.c: In function 'dwmac1000_dump_regs':
drivers/net/stmmac/dwmac1000_core.c:56: warning: cast from pointer to integer of different size
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
resource_size_t changed from `unsigned long' to `phys_addr_t`, which is either
`u32' or `u64'.
Print the whole resource to remove the cast and to make it future-proof.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Sun, 29 Aug 2010 19:27:34 +0000 (19:27 +0000)]
TCP: update initial windows according to RFC 5681
This updates the use of larger initial windows, as originally specified in
RFC 3390, to use the newer IW values specified in RFC 5681, section 3.1.
The changes made in RFC 5681 are:
a) the setting now is more clearly specified in units of segments (as the
comments by John Heffner emphasized, this was not very clear in RFC 3390);
b) for connections with 1095 < SMSS <= 2190 there is now a change:
- RFC 3390 says that IW <= 4380,
- RFC 5681 says that IW = 3 * SMSS <= 6570.
Since RFC 3390 is older and "only" proposed standard, whereas the newer RFC 5681
is already draft standard, it seems preferable to use the newer IW variant.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Sun, 29 Aug 2010 19:23:14 +0000 (19:23 +0000)]
dccp ccid-3: use per-route RTO or TCP RTO as fallback
This makes RTAX_RTO_MIN also available to CCID-3, replacing the compile-time
RTO lower bound with a per-route tunable value.
The original Kconfig option solved the problem that a very low RTT (in the
order of HZ) can trigger too frequent and unnecessary reductions of the
sending rate.
This tunable does not affect the initial RTO value of 2 seconds specified in
RFC 5348, section 4.2 and Appendix B. But like the hardcoded Kconfig value,
it allows to adapt to network conditions.
The same effect as the original Kconfig option of 100ms is now achieved by
> ip route replace to unicast 192.168.0.0/24 rto_min 100j dev eth0
(assuming HZ=1000).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Sun, 29 Aug 2010 19:23:13 +0000 (19:23 +0000)]
dccp ccid-2: Share TCP's minimum RTO code
Using a fixed RTO_MIN of 0.2 seconds was found to cause problems for CCID-2
over 802.11g: at least once per session there was a spurious timeout. It
helped to then increase the the value of RTO_MIN over this link.
Since the problem is the same as in TCP, this patch makes the solution from
commit "05bb1fad1cde025a864a90cfeb98dcbefe78a44a"
"[TCP]: Allow minimum RTO to be configurable via routing metrics."
available to DCCP.
This avoids reinventing the wheel, so that e.g. the following works in the
expected way now also for CCID-2:
> ip route change 10.0.0.2 rto_min 800 dev ath0
Luckily this useful rto_min function was recently moved to net/tcp.h,
which simplifies sharing code originating from TCP.
Documentation also updated (plus minor whitespace fixes).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Sun, 29 Aug 2010 19:23:12 +0000 (19:23 +0000)]
tcp/dccp: Consolidate common code for RFC 3390 conversion
This patch consolidates initial-window code common to TCP and CCID-2:
* TCP uses RFC 3390 in a packet-oriented manner (tcp_input.c) and
* CCID-2 uses RFC 3390 in packet-oriented manner (RFC 4341).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Sun, 29 Aug 2010 19:23:11 +0000 (19:23 +0000)]
dccp ccid-2: Remove wrappers around sk_{reset,stop}_timer()
This removes the wrappers around the sk timer functions, since not much is
gained from using them: the BUG_ON in start_rto_timer will never trigger
since that function is called only if:
* the RTO timer expires (rto_expire, and then timer_pending() is false);
* in tx_packet_sent only if !timer_pending() (BUG_ON is redundant here);
* previously in new_ack, after stopping the timer (timer_pending() false).
Removing the wrappers also clears the way for eventually replacing the
RTO timer with the icsk-retransmission-timer, as it is already part of the
DCCP socket.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Jerry Chu [Fri, 27 Aug 2010 19:13:28 +0000 (19:13 +0000)]
tcp: Add TCP_USER_TIMEOUT socket option.
This patch provides a "user timeout" support as described in RFC793. The
socket option is also needed for the the local half of RFC5482 "TCP User
Timeout Option".
TCP_USER_TIMEOUT is a TCP level socket option that takes an unsigned int,
when > 0, to specify the maximum amount of time in ms that transmitted
data may remain unacknowledged before TCP will forcefully close the
corresponding connection and return ETIMEDOUT to the application. If
0 is given, TCP will continue to use the system default.
Increasing the user timeouts allows a TCP connection to survive extended
periods without end-to-end connectivity. Decreasing the user timeouts
allows applications to "fail fast" if so desired. Otherwise it may take
upto 20 minutes with the current system defaults in a normal WAN
environment.
The socket option can be made during any state of a TCP connection, but
is only effective during the synchronized states of a connection
(ESTABLISHED, FIN-WAIT-1, FIN-WAIT-2, CLOSE-WAIT, CLOSING, or LAST-ACK).
Moreover, when used with the TCP keepalive (SO_KEEPALIVE) option,
TCP_USER_TIMEOUT will overtake keepalive to determine when to close a
connection due to keepalive failure.
The option does not change in anyway when TCP retransmits a packet, nor
when a keepalive probe will be sent.
This option, like many others, will be inherited by an acceptor from its
listener.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell [Sun, 29 Aug 2010 17:04:53 +0000 (17:04 +0000)]
IPVS: include net/ip6_checksum.h for csum_ipv6_magic
Fixes this build error:
net/netfilter/ipvs/ip_vs_core.c: In function 'ip_vs_nat_icmp_v6':
net/netfilter/ipvs/ip_vs_core.c:640: error: implicit declaration of function 'csum_ipv6_magic'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Fri, 27 Aug 2010 19:08:45 +0000 (19:08 +0000)]
starfire: use BUILD_BUG_ON for netdrv_addr_t
Detect size mismatch for netdrv_addr_t at build time rather than
checking at module load time.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Ion Badulescu <ionut@badula.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Fri, 27 Aug 2010 19:08:36 +0000 (19:08 +0000)]
starfire: use PCI_VDEVICE
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Ion Badulescu <ionut@badula.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Fri, 27 Aug 2010 19:08:26 +0000 (19:08 +0000)]
phonet: use for_each_set_bit
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Fri, 27 Aug 2010 19:08:13 +0000 (19:08 +0000)]
mlx4: use bitmap library
Replace loops calling set_bit() and clear_bit() with bitmap_set() and
bitmap_clear().
Unlike loops calling set_bit() and clear_bit(), bitmap_set() and
bitmap_clear() are not atomic. But this is ok.
Because the bitmap operations are protected by bitmap->lock
except for initialization of the bitmap in mlx4_bitmap_init().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Roland Dreier <rolandd@cisco.com> Cc: netdev@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Fri, 27 Aug 2010 16:41:56 +0000 (16:41 +0000)]
econet: kill unnecessary spin_lock_init()
The spinlock aun_queue_lock is initialized statically. It is unnecessary
to initialize by spin_lock_init() at module load time.
This is detected by the semantic patch.
// <smpl>
@def@
declarer name DEFINE_SPINLOCK;
identifier spinlock;
@@
DEFINE_SPINLOCK(spinlock);
@@
identifier def.spinlock;
@@
- spin_lock_init(&spinlock);
// </smpl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Julia Lawall <julia@diku.dk> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Thu, 26 Aug 2010 22:12:08 +0000 (22:12 +0000)]
slip: Use net_device_stats from struct net_device
Use net_device->stats for stats instead of private variable copies in
struct slip. Use ndo_get_stat64 so the additions can be performed on a private
destination buffer.
Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 27 Aug 2010 11:45:28 +0000 (13:45 +0200)]
mac80211: fix offchannel queue stop
Somebody noticed this problem, and I outlined
to them how to fix it, but haven't heard back
from them. So while I was adding the state
field I figured I could use it to fix it.
The problem, as I understand it, is that when
we go offchannel while the driver has a queue
stopped, the driver will likely start draining
the queue and then enable it while offchannel.
This in turn will enable the interface queue,
and that leads to transmitting data frames on
the wrong channel.
Fix this by keeping track of offchannel status
per interface, and not enabling the interface
queues on interfaces that are offchannel when
the driver enables a queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 27 Aug 2010 10:35:58 +0000 (12:35 +0200)]
mac80211: support runtime interface type changes
Add support to mac80211 for changing the interface
type even when the interface is UP, if the driver
supports it.
To achieve this
* add a new driver callback for switching,
* split some of the interface up/down code out
into new functions (do_open/do_stop), and
* maintain an own __SDATA_RUNNING bit that will
not be set during interface type, so that any
other code doesn't use the interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 27 Aug 2010 10:35:56 +0000 (12:35 +0200)]
mac80211: simplify zero address checks
The libertas_tf special code for zero addresses
is a bit too complex, it compares against a stack
value instead of using is_zero_ether_addr() and
tries to update all interfaces even if just the
one that's being brought up needs to be changed.
Additionally, the repeated check for a valid MAC
address need only be done if we actually changed
it on the fly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 27 Aug 2010 10:35:54 +0000 (12:35 +0200)]
mac80211: clean up ifdown/cleanup paths
There's a lot of redundant code in mac80211's
interface cleanup/down, for example freeing
AP beacons is done both when the interface is
set DOWN as well as when it is torn down, of
which only the former has any effect.
Also, a bunch of things should be closer to
where they matter, like the MLME timers that
we should cancel when disassociating, rather
than only when the interface is set DOWN.
Clean up all this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 27 Aug 2010 11:26:54 +0000 (14:26 +0300)]
mac80211: allow changing port control protocol
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Support this
in mac80211 via the cfg80211 API for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 27 Aug 2010 11:26:53 +0000 (14:26 +0300)]
cfg80211: allow changing port control protocol
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Allow setting
the ethertype for the protocol when a driver has
support for this. The default if unspecified is
EAP, of course.
Note: This is suitable only for station mode, not
for AP implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 27 Aug 2010 11:26:52 +0000 (14:26 +0300)]
mac80211: allow vendor specific cipher suites
Allow drivers to specify their own set of cipher
suites to advertise vendor-specific ciphers. The
driver is then required to implement hardware
crypto offload for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 27 Aug 2010 11:26:51 +0000 (14:26 +0300)]
cfg80211: allow vendor specific cipher suites
cfg80211 currently rejects all cipher suites it
doesn't know about for key length checking
purposes. This can lead to inconsistencies when
a driver advertises an algorithm that cfg80211
doesn't know about. Remove this rejection so
drivers can specify any algorithm they like.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 26 Aug 2010 11:30:27 +0000 (13:30 +0200)]
wl12xx: remove unneeded locking
With the scan callback now being callable from
any context, these unlocks/locks can go away.
This makes the code easier to understand, since
callers of these functions must no longer be
aware that the mutex may be dropped.
As Stanislaw is working on iwlwifi scanning, I
didn't change it to take advantage of the new
mac80211 semantics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log