ARM: OMAP2+: Add GPMC DT support for Ethernet child nodes
Besides being used to interface with external memory devices,
the General-Purpose Memory Controller can be used to connect
Pseudo-SRAM devices such as ethernet controllers to OMAP2+
processors using the TI GPMC as a data bus.
This patch allows an ethernet chip to be defined as an GPMC
child device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Jon Hunter <jon-hunter@ti.com>
ARM: OMAP2+: return -ENODEV if GPMC child device creation fails
gpmc_probe_nor_child() calls of_platform_device_create() to create a
platform device for the NOR child. If this function fails the value
of ret is returned to the caller but this value is zero since it was
assigned the return of a previous call to gpmc_cs_program_settings()
that had to succeed or otherwise gpmc_probe_nor_child() would have
returned before.
This means that if of_platform_device_create() fails, 0 will be returned
to the caller instead of an appropriate error code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Wed, 6 Mar 2013 20:36:47 +0000 (14:36 -0600)]
ARM: OMAP2+: Allow GPMC probe to complete even if CS mapping fails
When the GPMC driver is probed, we call gpmc_mem_init() to see which
chip-selects have already been configured and enabled by the boot-loader
and allocate space for them. If we fail to allocate space for one
chip-select, then we return failure from the probe and the GPMC driver
will not be available.
Rather than render the GPMC useless for all GPMC devices, if we fail to
allocate space for one chip-select print a warning and disable the
chip-select. This way other GPMC clients can still be used.
There is no downside to this approach, because all GPMC clients need to
request a chip-select before they can use the GPMC and on requesting a
chip-select, if memory has not already been reserved for the chip-select
then it will be.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Wed, 6 Mar 2013 20:12:59 +0000 (14:12 -0600)]
ARM: OMAP2+: Remove unnecesssary GPMC definitions and variable
With commit 21cc2bd (ARM: OMAP2+: Remove apollon board support) the
variable "boot_rom_space" is now not needed and the code surrounding
this variable can be cleaned up and simplified. Remove unnecessary
definitions and clean-up the comment as well.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Wed, 6 Mar 2013 18:00:10 +0000 (12:00 -0600)]
ARM: OMAP2+: Detect incorrectly aligned GPMC base address
Each GPMC chip-select can be configured to map 16MB, 32MB, 64MB or 128MB
of address space. The physical base address where a chip-select starts
is also configurable and must be aligned on a boundary that is equal to
or greater than the size of the address space mapped bt the chip-select.
When enabling a GPMC chip-select, ensure that the base address is aligned
to the appropriate boundary.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk> Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Mon, 25 Feb 2013 17:37:58 +0000 (11:37 -0600)]
ARM: OMAP2+: Convert ONENAND to retrieve GPMC settings from DT
When booting with device-tree, retrieve GPMC settings for ONENAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.
The user must now specify the ONENAND device width in the device-tree
binding so that the GPMC can be programmed correctly. Therefore, update
the device-tree binding documentation for ONENAND devices connected to
the GPMC to reflect this.
Please note that this does not include GPMC timings for ONENAND. The
timings are being calculated at runtime.
There is some legacy code that only enables read wait monitoring for
non-OMAP3 devices. There are no known OMAP3 device issues that prevent
this feature being enabled and so when booting with device-tree use the
wait-monitoring settings described in the device-tree blob.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Mon, 25 Feb 2013 17:36:47 +0000 (11:36 -0600)]
ARM: OMAP2+: Convert NAND to retrieve GPMC settings from DT
When booting with device-tree, retrieve GPMC settings for NAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Fri, 8 Feb 2013 22:46:13 +0000 (16:46 -0600)]
ARM: OMAP2+: Add device-tree support for NOR flash
NOR flash is not currently supported when booting with device-tree
on OMAP2+ devices. Add support to detect and configure NOR devices
when booting with device-tree.
Add documentation for the TI GPMC NOR binding.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Some of the GPMC timings parameters are currently missing from the GPMC
device-tree binding. Add these parameters to the binding documentation
as well as code to read them. Also add either "-ps" or "-ns" suffix to
the GPMC timing properties to indicate whether the timing is in
picoseconds or nanoseconds.
The existing code in gpmc_read_timings_dt() is checking the value of
of_property_read_u32() and only is successful storing the value read
in the gpmc_timings structure. Checking the return value in this case
is not necessary and we can simply read the value, if present, and
store directly in the gpmc_timings structure. Therefore, simplify the
code by removing these checks.
The comment in the gpmc_read_timings_dt() function, "only for OMAP3430"
is also incorrect as it is applicable to all OMAP3+ devices. So correct
this too.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Thu, 21 Feb 2013 19:00:21 +0000 (13:00 -0600)]
ARM: OMAP2+: Don't configure of chip-select options in gpmc_cs_configure()
With the addition of the gpmc_cs_program_settings(), we no longer need
or use gpmc_cs_configure() to configure some of the GPMC chip-select
options. So rename the function to gpmc_configure() and remove code that
modifies options in the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Thu, 21 Feb 2013 19:01:47 +0000 (13:01 -0600)]
ARM: OMAP2+: Convert TUSB to use gpmc_cs_program_settings()
Convert the OMAP2+ TUSB code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Thu, 21 Feb 2013 19:01:37 +0000 (13:01 -0600)]
ARM: OMAP2+: Convert SMC91x to use gpmc_cs_program_settings()
Convert the OMAP2+ SMC91x code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Move configuration of the GPMC settings outside retime function and
this does not need to be done if the timings are changed dynamically
at runtime.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Thu, 21 Feb 2013 21:43:08 +0000 (15:43 -0600)]
ARM: OMAP2+: Convert NAND to use gpmc_cs_program_settings()
Convert the OMAP2+ NAND code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
This moves the configuration of some GPMC options outside the
nand_gpmc_retime() because these options should only need to be set once
regardless of whether the gpmc timing is changing dynamically at runtime.
The programming of where the wait-pin is also moved slightly, but this
will not have any impact to existing devices as no boards are currently
setting the dev_ready variable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Thu, 21 Feb 2013 18:42:22 +0000 (12:42 -0600)]
ARM: OMAP2+: Convert ONENAND to use gpmc_cs_program_settings()
Convert the OMAP2+ ONENAND code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Thu, 21 Feb 2013 21:25:23 +0000 (15:25 -0600)]
ARM: OMAP2+: Add function for configuring GPMC settings
The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no common function for configuring these options and
various devices set these options by either programming the GPMC CONFIG1
register directly or by calling gpmc_cs_configure() to set some of the
options.
Add a new function for configuring all of the GPMC options. Having a common
function for configuring this options will simplify code and ease the
migration to device-tree.
Also add a new capability flag to detect devices that support the
address-address-data multiplexing mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Thu, 21 Feb 2013 19:46:22 +0000 (13:46 -0600)]
ARM: OMAP2+: Add structure for storing GPMC settings
The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no central structure for storing all these options
when configuring the GPMC for a given device. Some of the options are
stored in the GPMC timing structure and some are directly programmed
into the GPMC configuration register. Add a new structure to store
these options and convert code to use this structure. Adding this
structure will allow us to create a common function for configuring
these options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Jon Hunter [Wed, 20 Feb 2013 21:53:38 +0000 (15:53 -0600)]
ARM: OMAP2+: Add variable to store number of GPMC waitpins
The GPMC has wait-pin signals that can be assigned to a chip-select
to monitor the ready signal of an external device. Add a variable to
indicate the total number of wait-pins for a given device. This will
allow us to detect if the wait-pin being selected is valid or not.
When booting with device-tree read the number of wait-pins from the
device-tree blob. When device-tree is not used set the number of
wait-pins to 4 which is valid for OMAP2-5 devices. Newer devices
that have less wait-pins (such as AM335x) only support booting with
device-tree and so hard-coding the wait-pin number when not using
device-tree is fine.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The OMAP2+ code that configures the GPMC for ONENAND devices is copying
structures between functions unnecessarily. Avoid this by passing
pointers instead and simplify the code.
A pointer to structure "omap_onenand_platform_data" is passed to the
function omap2_onenand_calc_sync_timings(), but only the flags member
of the structure is used. Simplify the code by only passing the flags
member and not the entire structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Ezequiel Garcia [Tue, 12 Feb 2013 19:22:24 +0000 (16:22 -0300)]
ARM: omap2: gpmc: Remove redundant chip select out of range check
This check is done before the call to gpmc_cs_reserved() and
gpmc_cs_set_reserved() and it's redundant to do it again in each
function. This simplifies the code a bit.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Reviewed-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Ezequiel Garcia [Tue, 12 Feb 2013 19:22:19 +0000 (16:22 -0300)]
ARM: omap2: gpmc: Fix gpmc_cs_reserved() return value
Currently gpmc_cs_reserved() return value is somewhat inconsistent,
returning a negative value on an error condition, a positive value
if the chip select is reserved and zero if it's available.
Fix this by returning a boolean value as the function name suggests:
* true if the chip select is reserved,
* false if it's available
Suggested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Reviewed-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Mark Jackson [Tue, 5 Mar 2013 10:13:40 +0000 (10:13 +0000)]
ARM: OMAP: Clear GPMC bits when applying new setting.
When setting the GPMC device type, make sure any previous
bits are cleared down, before applying the new setting.
For OMAP4+ devices MUXADDDATA is a 2-bit field (bits 9:8)
where as for OMAP2/3 devices it was only a one bit field
(bit 9). For OMAP2/3 devices bit 8 is reserved and the
OMAP documentation says to write a 0 to this bit. So
clearing bit 8 on OMAP2/3 devices should not be a problem.
Hence update the code to handle both bits 8 and 9 for all
devices.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
[jon-hunter@ti.com: updated changelog] Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Jon Hunter [Mon, 18 Feb 2013 13:57:39 +0000 (07:57 -0600)]
ARM: OMAP2+: Fix broken gpmc support
Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by: Philip Avinash <avinashphilip@ti.com> Tested-by: Grazvydas Ignotas <notasas@gmail.com>
[tony@atomide.com: updated description to add breaking commit id] Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 11 Feb 2013 22:46:00 +0000 (14:46 -0800)]
ARM: OMAP1: Fix build related to kgdb.h no longer including serial_8250.h
Commit 16559ae4 (kgdb: remove #include <linux/serial_8250.h> from kgdb.h)
had a side effect of breaking omap1_defconfig build as some headers
were included indirectly:
arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function)
...
This worked earlier as linux/serial_8250.h included linux/serial_core.h,
via linux/serial_8250.h from linux/kgdb.h. Fix this by including the
necessary headers directly.
Linus Torvalds [Sun, 3 Mar 2013 22:24:59 +0000 (14:24 -0800)]
Merge tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers
Pull fbdev UAPI disintegration from David Howells:
"You'll be glad to here that the end is nigh for the UAPI patches.
Only the fbdev/framebuffer piece remains now that the SCSI stuff has
gone in.
Here are the UAPI disintegration bits for the fbdev drivers. It
appears that Florian hasn't had time to deal with my patch, but back
in December he did say he didn't mind if I pushed it forward."
Yay. No more uapi movement. And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.
* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/video
Linus Torvalds [Sun, 3 Mar 2013 22:22:53 +0000 (14:22 -0800)]
Merge tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- Update the Xen ACPI memory and CPU hotplug locking mechanism.
- Fix PAT issues wherein various applications would not start
- Fix handling of multiple MSI as AHCI now does it.
- Fix ARM compile failures.
* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: fix compile failure on ARM with Xen enabled
xen/pci: We don't do multiple MSI's.
xen/pat: Disable PAT using pat_enabled value.
xen/acpi: xen cpu hotplug minor updates
xen/acpi: xen memory hotplug minor updates
Linus Torvalds [Sun, 3 Mar 2013 21:23:02 +0000 (13:23 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more VFS bits from Al Viro:
"Unfortunately, it looks like xattr series will have to wait until the
next cycle ;-/
This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
more file_inode() work"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify path_get/path_put and fs_struct.c stuff
fix nommu breakage in shmem.c
cache the value of file_inode() in struct file
9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
9p: make sure ->lookup() adds fid to the right dentry
9p: untangle ->lookup() a bit
9p: double iput() in ->lookup() if d_materialise_unique() fails
9p: v9fs_fid_add() can't fail now
v9fs: get rid of v9fs_dentry
9p: turn fid->dlist into hlist
9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
more file_inode() open-coded instances
selinux: opened file can't have NULL or negative ->f_path.dentry
(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)
Linus Torvalds [Sun, 3 Mar 2013 20:58:43 +0000 (12:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull second set of s390 patches from Martin Schwidefsky:
"The main part of this merge are Heikos uaccess patches. Together with
commit 09884964335e ("mm: do not grow the stack vma just because of an
overrun on preceding vma") the user string access is hopefully fixed
for good.
In addition some bug fixes and two cleanup patches."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/module: fix compile warning
qdio: remove unused parameters
s390/uaccess: fix kernel ds access for page table walk
s390/uaccess: fix strncpy_from_user string length check
input: disable i8042 PC Keyboard controller for s390
s390/dis: Fix invalid array size
s390/uaccess: remove pointless access_ok() checks
s390/uaccess: fix strncpy_from_user/strnlen_user zero maxlen case
s390/uaccess: shorten strncpy_from_user/strnlen_user
s390/dasd: fix unresponsive device after all channel paths were lost
s390/mm: ignore change bit for vmemmap
s390/page table dumper: add support for change-recording override bit
Linus Torvalds [Sun, 3 Mar 2013 20:57:38 +0000 (12:57 -0800)]
Merge branch 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull second round of PARISC updates from Helge Deller:
"The most important fix in this branch is the switch of io_setup,
io_getevents and io_submit syscalls to use the available compat
syscalls when running 32bit userspace on 64bit kernel. Other than
that it's mostly removal of compile warnings."
* 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix redefinition of SET_PERSONALITY
parisc: do not install modules when installing kernel
parisc: fix compile warnings triggered by atomic_sub(sizeof(),v)
parisc: check return value of down_interruptible() in hp_sdc_rtc.c
parisc: avoid unitialized variable warning in pa_memcpy()
parisc: remove unused variable 'compat_val'
parisc: switch to compat_functions of io_setup, io_getevents and io_submit
parisc: select ARCH_WANT_FRAME_POINTERS
Linus Torvalds [Sun, 3 Mar 2013 20:06:09 +0000 (12:06 -0800)]
Merge tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull new ImgTec Meta architecture from James Hogan:
"This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of
metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()"
* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
metag: Provide dma_get_sgtable()
metag: prom.h: remove declaration of metag_dt_memblock_reserve()
metag: copy devicetree to non-init memory
metag: cleanup metag_ksyms.c includes
metag: move mm/init.c exports out of metag_ksyms.c
metag: move usercopy.c exports out of metag_ksyms.c
metag: move setup.c exports out of metag_ksyms.c
metag: move kick.c exports out of metag_ksyms.c
metag: move traps.c exports out of metag_ksyms.c
metag: move irq enable out of irqflags.h on SMP
genksyms: fix metag symbol prefix on crc symbols
metag: hugetlb: convert to vm_unmapped_area()
metag: export clear_page and copy_page
metag: export metag_code_cache_flush_all
metag: protect more non-MMU memory regions
metag: make TXPRIVEXT bits explicit
metag: kernel/setup.c: sort includes
perf: Enable building perf tools for Meta
metag: add boot time LNKGET/LNKSET check
metag: add __init to metag_cache_probe()
...
Linus Torvalds [Sun, 3 Mar 2013 19:54:39 +0000 (11:54 -0800)]
Merge branch 'for-linus' of git://git.linaro.org/people/rmk/linux-arm
Pull late ARM updates from Russell King:
"Here is the late set of ARM updates for this merge window; in here is:
- The ARM parts of the broadcast timer support, core parts merged
through tglx's tree. This was left over from the previous merge to
allow the dependency on tglx's tree to be resolved.
- A fix to the VFP code which shows up on Raspberry Pi's, as well as
fixing the fallout from a previous commit in this area.
- A number of smaller fixes scattered throughout the ARM tree"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: Fix broken commit 0cc41e4a21d43 corrupting kernel messages
ARM: fix scheduling while atomic warning in alignment handling code
ARM: VFP: fix emulation of second VFP instruction
ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDR
ARM: 7640/1: memory: tegra_ahb_enable_smmu() depends on TEGRA_IOMMU_SMMU
ARM: 7654/1: Preserve L_PTE_VALID in pte_modify()
ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clock
ARM: 7651/1: remove unused smp_timer_broadcast #define
Linus Torvalds [Sun, 3 Mar 2013 18:25:47 +0000 (10:25 -0800)]
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patch from Greg Kroah-Hartman:
"Here is one remaining patch for 3.9-rc1. It is for the hyper-v
drivers, and had to wait until some other patches went in through the
x86 tree."
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Use the new infrastructure for delivering VMBUS interrupts
Linus Torvalds [Sun, 3 Mar 2013 18:24:57 +0000 (10:24 -0800)]
Merge tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patch revert from Greg Kroah-Hartman:
"Here is one remaining USB patch for 3.9-rc1, it reverts a 3.8 patch
that has caused a lot of regressions for some VIA EHCI controllers."
* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: EHCI: revert "remove ASS/PSS polling timeout"
Linus Torvalds [Sun, 3 Mar 2013 18:23:29 +0000 (10:23 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- fixes and improvements
- devicetree bindings
- conversion to watchdog generic framework of the following drivers:
- booke_wdt
- bcm47xx_wdt.c
- at91sam9_wdt
- Removal of old STMP3xxx driver
- Addition of following new drivers:
- new driver for STMP3xxx and i.MX23/28
- Retu watchdog driver"
* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: sp805_wdt depends on ARM
watchdog: davinci_wdt: update to devm_* API
watchdog: davinci_wdt: use devm managed clk get
watchdog: at91rm9200: add DT support
watchdog: add timeout-sec property binding
watchdog: at91sam9_wdt: Convert to use the watchdog framework
watchdog: omap_wdt: Add option nowayout
watchdog: core: dt: add support for the timeout-sec dt property
watchdog: bcm47xx_wdt.c: add hard timer
watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
watchdog: bcm47xx_wdt.c: rename ops methods
watchdog: bcm47xx_wdt.c: use platform device
watchdog: bcm47xx_wdt.c: convert to watchdog core api
watchdog: Convert BookE watchdog driver to watchdog infrastructure
watchdog: s3c2410_wdt: Use devm_* functions
watchdog: remove old STMP3xxx driver
watchdog: add new driver for STMP3xxx and i.MX23/28
rtc: stmp3xxx: add wdt-accessor function
watchdog: introduce retu_wdt driver
watchdog: intel_scu_watchdog: fix Kconfig dependency
...
Linus Torvalds [Sun, 3 Mar 2013 18:20:22 +0000 (10:20 -0800)]
Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull second set of slave-dmaengine updates from Vinod Koul:
"Arnd's patch moves the dw_dmac to use generic DMA binding. I agreed
to merge this late as it will avoid the conflicts between trees.
The second patch from Matt adding a dma_request_slave_channel_compat
API was supposed to be picked up, but somehow never got picked up.
Some patches dependent on this are already in -next :("
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw_dmac: move to generic DMA binding
dmaengine: add dma_request_slave_channel_compat()
Linus Torvalds [Sun, 3 Mar 2013 18:16:19 +0000 (10:16 -0800)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"Mostly relatively small updates, along with some hardware enablement
for Sony hardware and a pile of updates to Google's Chromebook driver"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (49 commits)
ideapad-laptop: Depend on BACKLIGHT_CLASS_DEVICE instead of selecting it
ideapad: depends on backlight subsystem and update comment
Platform: x86: chromeos_laptop - add i915 gmbuses to adapter names
Platform: x86: chromeos_laptop - Add isl light sensor for Pixel
Platform: x86: chromeos_laptop - Add a more general add_i2c_device
Platform: x86: chromeos_laptop - Add Pixel Touchscreen
Platform: x86: chromeos_laptop - Add support for probing devices
Platform: x86: chromeos_laptop - Add Pixel Trackpad
hp-wmi: fix handling of platform device
sony-laptop: leak in error handling sony_nc_lid_resume_setup()
hp-wmi: Add support for SMBus hotkeys
asus-wmi: Fix unused function build warning
acer-wmi: avoid the warning of 'devices' may be used uninitialized
drivers/platform/x86/thinkpad_acpi.c: Handle HKEY event 0x6040
Platform: x86: chromeos_laptop - Add HP Pavilion 14
Platform: x86: chromeos_laptop - Add Taos tsl2583 device
Platform: x86: chromeos_laptop - Add Taos tsl2563 device
Platform: x86: chromeos_laptop - Add Acer C7 trackpad
Platform: x86: chromeos_laptop - Rename setup_lumpy_tp to setup_cyapa_smbus_tp
asus-laptop: always report brightness key events
...
fs/btrfs/raid56.c: In function 'btrfs_alloc_stripe_hash_table':
fs/btrfs/raid56.c:206:3: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
fs/btrfs/raid56.c:206:9: warning: assignment makes pointer from integer without a cast [enabled by default]
fs/btrfs/raid56.c:226:4: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Linus Torvalds [Sun, 3 Mar 2013 03:33:21 +0000 (19:33 -0800)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Various bug fixes for ext4. The most important is a fix for the new
extent cache's slab shrinker which can cause significant, user-visible
pauses when the system is under memory pressure."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: enable quotas before orphan cleanup
ext4: don't allow quota mount options when quota feature enabled
ext4: fix a warning from sparse check for ext4_dir_llseek
ext4: convert number of blocks to clusters properly
ext4: fix possible memory leak in ext4_remount()
jbd2: fix ERR_PTR dereference in jbd2__journal_start
ext4: use percpu counter for extent cache count
ext4: optimize ext4_es_shrink()
Linus Torvalds [Sun, 3 Mar 2013 03:32:06 +0000 (19:32 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull sigprocmask compat fix from Al Viro:
"generic compat_sys_rt_sigprocmask() had a very dumb braino; I'd spent
quite a while staring at the offending commit before finally managing
to spot the idiocy ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
fix compat_sys_rt_sigprocmask()
Linus Torvalds [Sun, 3 Mar 2013 00:46:07 +0000 (16:46 -0800)]
Merge tag 'nfs-for-3.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"We've just concluded another Connectathon interoperability testing
week, and so here are the fixes for the bugs that were discovered:
- Don't allow NFS silly-renamed files to be deleted
- Don't start the retransmission timer when out of socket space
- Fix a couple of pnfs-related Oopses.
- Fix one more NFSv4 state recovery deadlock
- Don't loop forever when LAYOUTGET returns NFS4ERR_LAYOUTTRYLATER"
* tag 'nfs-for-3.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: One line comment fix
NFSv4.1: LAYOUTGET EDELAY loops timeout to the MDS
SUNRPC: add call to get configured timeout
PNFS: set the default DS timeout to 60 seconds
NFSv4: Fix another open/open_recovery deadlock
nfs: don't allow nfs_find_actor to match inodes of the wrong type
NFSv4.1: Hold reference to layout hdr in layoutget
pnfs: fix resend_to_mds for directio
SUNRPC: Don't start the retransmission timer when out of socket space
NFS: Don't allow NFS silly-renamed files to be deleted, no signal
Linus Torvalds [Sun, 3 Mar 2013 00:41:54 +0000 (16:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs update from Chris Mason:
"The biggest feature in the pull is the new (and still experimental)
raid56 code that David Woodhouse started long ago. I'm still working
on the parity logging setup that will avoid inconsistent parity after
a crash, so this is only for testing right now. But, I'd really like
to get it out to a broader audience to hammer out any performance
issues or other problems.
scrub does not yet correct errors on raid5/6 either.
Josef has another pass at fsync performance. The big change here is
to combine waiting for metadata with waiting for data, which is a big
latency win. It is also step one toward using atomics from the
hardware during a commit.
Mark Fasheh has a new way to use btrfs send/receive to send only the
metadata changes. SUSE is using this to make snapper more efficient
at finding changes between snapshosts.
Snapshot-aware defrag is also included.
Otherwise we have a large number of fixes and cleanups. Eric Sandeen
wins the award for removing the most lines, and I'm hoping we steal
this idea from XFS over and over again."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (118 commits)
btrfs: fixup/remove module.h usage as required
Btrfs: delete inline extents when we find them during logging
btrfs: try harder to allocate raid56 stripe cache
Btrfs: cleanup to make the function btrfs_delalloc_reserve_metadata more logic
Btrfs: don't call btrfs_qgroup_free if just btrfs_qgroup_reserve fails
Btrfs: remove reduplicate check about root in the function btrfs_clean_quota_tree
Btrfs: return ENOMEM rather than use BUG_ON when btrfs_alloc_path fails
Btrfs: fix missing deleted items in btrfs_clean_quota_tree
btrfs: use only inline_pages from extent buffer
Btrfs: fix wrong reserved space when deleting a snapshot/subvolume
Btrfs: fix wrong reserved space in qgroup during snap/subv creation
Btrfs: remove unnecessary dget_parent/dput when creating the pending snapshot
btrfs: remove a printk from scan_one_device
Btrfs: fix NULL pointer after aborting a transaction
Btrfs: fix memory leak of log roots
Btrfs: copy everything if we've created an inline extent
btrfs: cleanup for open-coded alignment
Btrfs: do not change inode flags in rename
Btrfs: use reserved space for creating a snapshot
clear chunk_alloc flag on retryable failure
...
Linus Torvalds [Sun, 3 Mar 2013 00:33:54 +0000 (16:33 -0800)]
Merge tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
"Fairly unexciting MTD merge for 3.9:
- misc clean-ups in the MTD command-line partitioning parser
(cmdlinepart)
- add flash locking support for STmicro chips serial flash chips, as
well as for CFI command set 2 chips.
- new driver for the ELM error correction HW module found in various
TI chips, enable the OMAP NAND driver to use the ELM HW error
correction
- added number of new serial flash IDs
- various fixes and improvements in the gpmi NAND driver
- bcm47xx NAND driver improvements
- make the mtdpart module actually removable"
* tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd: (45 commits)
mtd: map: BUG() in non handled cases
mtd: bcm47xxnflash: use pr_fmt for module prefix in messages
mtd: davinci_nand: Use managed resources
mtd: mtd_torturetest can cause stack overflows
mtd: physmap_of: Convert device allocation to managed devm_kzalloc()
mtd: at91: atmel_nand: for PMECC, add code to check the ONFI parameter ECC requirement.
mtd: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is optional.
mtd: atmel_nand: avoid to report an error when lookup table offset is 0.
mtd: bcm47xxsflash: adjust names of bus-specific functions
mtd: bcm47xxpart: improve probing of nvram partition
mtd: bcm47xxpart: add support for other erase sizes
mtd: bcm47xxnflash: register this as normal driver
mtd: bcm47xxnflash: fix message
mtd: bcm47xxsflash: register this as normal driver
mtd: bcm47xxsflash: write number of written bytes
mtd: gpmi: add sanity check for the ECC
mtd: gpmi: set the Golois Field bit for mx6q's BCH
mtd: devices: elm: Removes <xx> literals in elm DT node
mtd: gpmi: fix a dereferencing freed memory error
mtd: fix the wrong timeo for panic_nand_wait()
...
Jan Kara [Sat, 2 Mar 2013 23:22:38 +0000 (18:22 -0500)]
ext4: enable quotas before orphan cleanup
When using quota feature we need to enable quotas before orphan cleanup
so that changes happening during it are properly reflected in quota
accounting.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Jan Kara [Sat, 2 Mar 2013 22:57:08 +0000 (17:57 -0500)]
ext4: don't allow quota mount options when quota feature enabled
So far we silently ignored when quota mount options were set while quota
feature was enabled. But this can create confusion in userspace when
mount options are set but silently ignored and also creates opportunities
for bugs when we don't properly test all quota types. Actually
ext4_mark_dquot_dirty() forgets to test for quota feature so it was
dependent on journaled quota options being set. OTOH ext4_orphan_cleanup()
tries to enable journaled quota when quota options are specified which is
wrong when quota feature is enabled.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Zheng Liu [Sat, 2 Mar 2013 22:24:05 +0000 (17:24 -0500)]
ext4: fix a warning from sparse check for ext4_dir_llseek
ext4_dir_llseek is only used as a callback function, and no one calls
it directly. So make it as a static function in order to remove a
warning message from sparse check.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
James Hogan [Tue, 19 Feb 2013 13:25:46 +0000 (13:25 +0000)]
metag: Provide dma_get_sgtable()
metag/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function 'vb2_dc_get_base_sgt':
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function 'dma_get_sgtable'
For architectures using dma_map_ops, dma_get_sgtable() is provided in
<asm-generic/dma-mapping-common.h>.
Metag does not use dma_map_ops yet, hence it should implement it as an
inline stub using dma_common_get_sgtable().
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
James Hogan [Wed, 20 Feb 2013 13:59:13 +0000 (13:59 +0000)]
metag: copy devicetree to non-init memory
Make a copy of the device tree blob in non-init memory. It is required
when using built-in device tree files that the platform code copies the
blob to non-init memory prior to calling unflatten_device_tree(),
otherwise the strings that the device tree refer to will get poisoned
and potentially reused, breaking later reading of the device tree
post-init (such as compatible matching in modules, debugfs, and the
procfs interface).
Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Vineet Gupta <vgupta@synopsys.com>
James Hogan [Wed, 13 Feb 2013 13:19:15 +0000 (13:19 +0000)]
metag: move mm/init.c exports out of metag_ksyms.c
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in mm/init.c into mm/init.c.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Wed, 13 Feb 2013 12:57:10 +0000 (12:57 +0000)]
metag: move usercopy.c exports out of metag_ksyms.c
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in usercopy.c into usercopy.c
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Wed, 13 Feb 2013 12:55:51 +0000 (12:55 +0000)]
metag: move setup.c exports out of metag_ksyms.c
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in setup.c into setup.c
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Wed, 13 Feb 2013 13:01:55 +0000 (13:01 +0000)]
metag: move kick.c exports out of metag_ksyms.c
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in kick.c into kick.c
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Wed, 13 Feb 2013 12:19:03 +0000 (12:19 +0000)]
metag: move traps.c exports out of metag_ksyms.c
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in traps.c into traps.c
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Tue, 12 Feb 2013 16:04:53 +0000 (16:04 +0000)]
metag: move irq enable out of irqflags.h on SMP
The SMP version of arch_local_irq_enable() uses preempt_disable(), but
<asm/irqflags.h> doesn't include <linux/preempt.h> causing the following
errors on SMP when pstore/ftrace is enabled (caught by buildbot smp
allyesconfig):
In file included from include/linux/irqflags.h:15,
from fs/pstore/ftrace.c:16:
arch/metag/include/asm/irqflags.h: In function 'arch_local_irq_enable':
arch/metag/include/asm/irqflags.h:84: error: implicit declaration of function 'preempt_disable'
arch/metag/include/asm/irqflags.h:86: error: implicit declaration of function 'preempt_enable_no_resched'
However <linux/preempt.h> cannot be easily included from
<asm/irqflags.h> as it can cause circular include dependencies in the
!SMP case, and potentially in the SMP case in the future. Therefore move
the SMP implementation of arch_local_irq_enable() into traps.c and use
an inline version of get_trigger_mask() which is also defined in traps.c
for SMP.
This adds an extra layer of function call / stack push when
preempt_disable needs to call other functions, however in the
non-preemptive SMP case it should be about as fast, as it was already
calling the get_trigger_mask() function which is now used inline.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Mon, 11 Feb 2013 15:40:24 +0000 (15:40 +0000)]
genksyms: fix metag symbol prefix on crc symbols
Meta uses symbol prefixes, so add "metag" to the list of architectures
to set the mod_prefix to "_" for. This fixes __crc_* symbols to add the
extra underscore to match _CRC_SYMBOL macro in <linux/export.h> and so
that modpost finds them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Mon, 11 Feb 2013 17:28:10 +0000 (17:28 +0000)]
metag: hugetlb: convert to vm_unmapped_area()
Convert hugetlb_get_unmapped_area_new_pmd() to use vm_unmapped_area()
rather than searching the virtual address space itself. This fixes the
following errors in linux-next due to the specified members being
removed after other architectures have already been converted:
arch/metag/mm/hugetlbpage.c: In function 'hugetlb_get_unmapped_area_new_pmd':
arch/metag/mm/hugetlbpage.c:199: error: 'struct mm_struct' has no member named 'cached_hole_size'
arch/metag/mm/hugetlbpage.c:200: error: 'struct mm_struct' has no member named 'free_area_cache'
arch/metag/mm/hugetlbpage.c:215: error: 'struct mm_struct' has no member named 'cached_hole_size'
Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Michel Lespinasse <walken@google.com>
James Hogan [Thu, 31 Jan 2013 13:27:35 +0000 (13:27 +0000)]
metag: make TXPRIVEXT bits explicit
Define PRIV_BITS using explicit constants from <asm/metag_regs.h> rather
than with a hard coded value. This also adds a couple of missing
definitions for the TXPRIVEXT priv bits for protecting writes to TXTIMER
and the trace registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Thu, 31 Jan 2013 11:06:03 +0000 (11:06 +0000)]
metag: add boot time LNKGET/LNKSET check
Add boot time check for whether LNKGET/LNKSET go through or around the
cache. Depending on the configuration an info message (no harm), warning
(technically wrong but no harm), or big WARN (expect failure in either
kernel or userland) may be emitted if the behaviour is not as expected:
Configuration Hardware Response
------------------------------------------ -------- --------
AROUND_CACHE through pr_info
!AROUND_CACHE && ATOMICITY_LNKGET around WARN (kernel)
" && !ATOMICITY_LNKGET && SMP around WARN (user)
" " && !SMP around pr_warn
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Fri, 21 Sep 2012 16:38:15 +0000 (17:38 +0100)]
metag: Add JTAG Debug Adapter (DA) support
Add basic JTAG Debug Adapter (DA) support so that drivers which
communicate with the DA can detect whether one is actually present
(otherwise the target will halt indefinitely).
This allows the metag_da TTY driver and imgdafs filesystem driver to be
built, updates defconfigs, and sets up the metag_da console early if
it's configured in.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Wed, 5 Dec 2012 11:34:13 +0000 (11:34 +0000)]
Kconfig.debug: add METAG to dependency lists
Add [!]METAG to a couple of Kconfig dependencies in lib/Kconfig.debug.
Don't allow stack utilization instrumentation on metag, and allow
building with frame pointers.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: "Paul E. McKenney" <paul.mckenney@linaro.org> Cc: Akinobu Mita <akinobu.mita@gmail.com> Cc: Michel Lespinasse <walken@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com>
The above commit combined several arch-specific vma flags into one, and
in the process it changed the VM_GROWSUP definition to depend on
specific architectures rather than CONFIG_STACK_GROWSUP. Therefore add
an ifdef for CONFIG_METAG to also set VM_GROWSUP.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Michel Lespinasse <walken@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-mm@kvack.org
James Hogan [Tue, 9 Oct 2012 10:00:27 +0000 (11:00 +0100)]
metag: Basic documentation
Add basic metag documentation. This includes an outline description of
the ABIs (including syscall ABI) and calling conventions, similar to the
one in Documentation/frv/.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Rob Landley <rob@landley.net> Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: linux-doc@vger.kernel.org
James Hogan [Tue, 9 Oct 2012 10:00:24 +0000 (11:00 +0100)]
metag: Atomics, locks and bitops
Add header files to implement Meta hardware thread locks (used by some
other atomic operations), atomics, spinlocks, and bitops.
There are 2 main types of atomic primitives for metag (in addition to
IRQs off on UP):
- LOCK instructions provide locking between hardware threads.
- LNKGET/LNKSET instructions provide load-linked/store-conditional
operations allowing for lighter weight atomics on Meta2
LOCK instructions allow for hardware threads to acquire voluntary or
exclusive hardware thread locks:
- LOCK0 releases exclusive and voluntary lock from the running hardware
thread.
- LOCK1 acquires the voluntary hardware lock, blocking until it becomes
available.
- LOCK2 implies LOCK1, and additionally acquires the exclusive hardware
lock, blocking all other hardware threads from executing.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
James Hogan [Tue, 9 Oct 2012 09:54:51 +0000 (10:54 +0100)]
metag: System Calls
Add metag system call and gateway page interfaces. The metag
architecture port uses the generic system call numbers from
asm-generic/unistd.h, as well as a user gateway page mapped at
0x6ffff000 which contains fast atomic primitives (depending on SMP) and
a fast method of accessing TLS data.
System calls use the SWITCH instruction with the immediate 0x440001 to
signal a system call.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
projects / linux-beck.git / log