Sergei Shtylyov [Mon, 8 May 2006 20:58:28 +0000 (00:58 +0400)]
Fix RTL8019AS init for Toshiba RBTX49xx boards
Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
au1000_eth.c: use ether_crc() from <linux/crc32.h>
since the au1000 driver already selects the CRC32 routines, simply replace
the internal ether_crc() implementation with the semantically equivalent
one from <linux/crc32.h>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org> Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Add more support for the Yukon Ultra chip found in dual core centino laptops.
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org> Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Mask for transmit ring status was picking up bits from the
unused sync ring. They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Andi Kleen [Mon, 8 May 2006 13:17:31 +0000 (15:17 +0200)]
[PATCH] x86_64: Move ondemand timer into own work queue
Taking the cpu hotplug semaphore in a normal events workqueue
is unsafe because other tasks can wait for any workqueues with
it hold. This results in a deadlock.
Move the DBS timer into its own work queue which is not
affected by other work queue flushes to avoid this.
Andi Kleen [Mon, 8 May 2006 13:17:28 +0000 (15:17 +0200)]
[PATCH] x86_64: Avoid EBDA area in early boot allocator
Based on analysis&patch from Robert Hentosch
Observed on a Dell PE6850 with 16GB
The problem occurs very early on, when the kernel allocates space for the
temporary memory map called bootmap. The bootmap overlaps the EBDA region.
EBDA region is not historically reserved in the e820 mapping. When the
bootmap is freed it marks the EBDA region as usable.
If you notice in setup.c there is already code to work around the EBDA
in reserve_ebda_region(), this check however occurs after the bootmap
is allocated and doesn't prevent the bootmap from using this range.
AK: I redid the original patch. Thanks also to Jan Beulich for
spotting some mistakes.
Corey Minyard [Mon, 8 May 2006 13:17:25 +0000 (15:17 +0200)]
[PATCH] x86_64: add nmi_exit to die_nmi
Playing with NMI watchdog on x86_64, I discovered that it didn't
do what I expected. It always panic-ed, even when it didn't
happen from interrupt context. This patch solves that
problem for me. Also, in this case, do_exit() will be called
with interrupts disabled, I believe. Would it be wise to also
call local_irq_enable() after nmi_exit()?
[Yes I added it -AK]
Currently, on x86_64, any NMI watchdog timeout will cause a panic
because the irq count will always be set to be in an interrupt
when do_exit() is called from die_nmi(). If we add nmi_exit() to
the die_nmi() call (since the nmi will never exit "normally")
it seems to solve this problem. The following small program
can be used to trigger the NMI watchdog to reproduce this:
main ()
{
iopl(3);
for (;;) asm("cli");
}
Corey Minyard [Mon, 8 May 2006 13:17:22 +0000 (15:17 +0200)]
[PATCH] x86_64: fix die_lock nesting
I noticed this when poking around in this area.
The oops_begin() function in x86_64 would only conditionally claim
the die_lock if the call is nested, but oops_end() would always
release the spinlock. This patch adds a nest count for the die lock
so that the release of the lock is only done on the final oops_end().
Kimball Murray [Mon, 8 May 2006 13:17:16 +0000 (15:17 +0200)]
[PATCH] x86_64: avoid IRQ0 ioapic pin collision
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: Do not overwrite makefile as anohter user
kbuild: drivers/video/logo/ - fix ident glitch
kbuild: fix gen_initramfs_list.sh
kbuild modpost - relax driver data name
kbuild: removing .tmp_versions considered harmful
kbuild: fix modpost segfault for 64bit mipsel kernel
Trond Myklebust [Mon, 8 May 2006 03:02:42 +0000 (23:02 -0400)]
[PATCH] fs/locks.c: Fix lease_init
It is insane to be giving lease_init() the task of freeing the lock it is
supposed to initialise, given that the lock is not guaranteed to be
allocated on the stack. This causes lockups in fcntl_setlease().
Problem diagnosed by Daniel Hokka Zakrisson <daniel@hozac.com>
Also fix a slab leak in __setlease() due to an uninitialised return value.
Problem diagnosed by Björn Steinbrink.
Jan Beulich [Tue, 2 May 2006 10:33:20 +0000 (12:33 +0200)]
kbuild: Do not overwrite makefile as anohter user
Change the conditional of the outputmakefile rule to be evaluated entirely
in make, and add a conditional to not touch the generated makefile when e.g.
running 'make install' as root while the build was done as non-root. Also
adjust the comment describing this, and move the message printing and
redirection to mkmakefile.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This holds the task lock (and, for ptrace_attach, the tasklist_lock)
over the actual attach event, which closes a race between attacking to a
thread that is either doing a PTRACE_TRACEME or getting de-threaded.
Thanks to Oleg Nesterov for reminding me about this, and Chris Wright
for noticing a lost return value in my first version.
Hua Zhong [Sun, 7 May 2006 01:11:39 +0000 (18:11 -0700)]
[IPV4]: Remove likely in ip_rcv_finish()
This is another result from my likely profiling tool
(dwalker@mvista.com just sent the patch of the profiling tool to
linux-kernel mailing list, which is similar to what I use).
On my system (not very busy, normal development machine within a
VMWare workstation), I see a 6/5 miss/hit ratio for this "likely".
Signed-off-by: Hua Zhong <hzhong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[NET]: Create netdev attribute_groups with class_device_add
Atomically create attributes when class device is added. This avoids
the race between registering class_device (which generates hotplug
event), and the creation of attribute groups.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the support of attribute groups in class_device's to allow
groups to be created as part of the registration process. This allows
network device's to avoid race between registration and creating
groups.
Note that unlike attributes that are a property of the class object,
the groups are a property of the class_device object. This is done
because there are different types of network devices (wireless for
example).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 6 May 2006 10:29:21 +0000 (11:29 +0100)]
[ARM] rtc-sa1100: fix compiler warnings and error cleanup
Fix:
drivers/rtc/rtc-sa1100.c: In function `sa1100_rtc_proc':
drivers/rtc/rtc-sa1100.c:298: warning: unsigned int format, long unsigned int arg (arg 3)
and arrange for sa1100_rtc_open() to pass the devid to free_irq()
rather than NULL.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 May 2006 10:26:30 +0000 (11:26 +0100)]
[ARM] Allow SA1100 RTC alarm to be configured for wakeup
The SA1100 RTC alarm can be configured to wake up the CPU
from sleep mode, and the RTC driver has been using the
API to configure this mode. Unfortunately, the code was
which sets the required bit in the hardware was missing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
John Heffner [Sat, 6 May 2006 00:41:44 +0000 (17:41 -0700)]
[TCP]: Fix snd_cwnd adjustments in tcp_highspeed.c
Xiaoliang (David) Wei wrote:
> Hi gurus,
>
> I am reading the code of tcp_highspeed.c in the kernel and have a
> question on the hstcp_cong_avoid function, specifically the following
> AI part (line 136~143 in net/ipv4/tcp_highspeed.c ):
>
> /* Do additive increase */
> if (tp->snd_cwnd < tp->snd_cwnd_clamp) {
> tp->snd_cwnd_cnt += ca->ai;
> if (tp->snd_cwnd_cnt >= tp->snd_cwnd) {
> tp->snd_cwnd++;
> tp->snd_cwnd_cnt -= tp->snd_cwnd;
> }
> }
>
> In this part, when (tp->snd_cwnd_cnt == tp->snd_cwnd),
> snd_cwnd_cnt will be -1... snd_cwnd_cnt is defined as u16, will this
> small chance of getting -1 becomes a problem?
> Shall we change it by reversing the order of the cwnd++ and cwnd_cnt -=
> cwnd?
Absolutely correct. Thanks.
Signed-off-by: John Heffner <jheffner@psc.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Sat, 6 May 2006 00:19:26 +0000 (17:19 -0700)]
[NETROM/ROSE]: Kill module init version kernel log messages.
There are out of date and don't tell the user anything useful.
The similar messages which IPV4 and the core networking used
to output were killed a long time ago.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 6 May 2006 00:09:13 +0000 (17:09 -0700)]
[DCCP]: Fix sock_orphan dead lock
Calling sock_orphan inside bh_lock_sock in dccp_close can lead to dead
locks. For example, the inet_diag code holds sk_callback_lock without
disabling BH. If an inbound packet arrives during that admittedly tiny
window, it will cause a dead lock on bh_lock_sock. Another possible
path would be through sock_wfree if the network device driver frees the
tx skb in process context with BH enabled.
We can fix this by moving sock_orphan out of bh_lock_sock.
The tricky bit is to work out when we need to destroy the socket
ourselves and when it has already been destroyed by someone else.
By moving sock_orphan before the release_sock we can solve this
problem. This is because as long as we own the socket lock its
state cannot change.
So we simply record the socket state before the release_sock
and then check the state again after we regain the socket lock.
If the socket state has transitioned to DCCP_CLOSED in the time being,
we know that the socket has been destroyed. Otherwise the socket is
still ours to keep.
This problem was discoverd by Ingo Molnar using his lock validator.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
[SCTP]: Prevent possible infinite recursion with multiple bundled DATA.
There is a rare situation that causes lksctp to go into infinite recursion
and crash the system. The trigger is a packet that contains at least the
first two DATA fragments of a message bundled together. The recursion is
triggered when the user data buffer is smaller that the full data message.
The problem is that we clone the skb for every fragment in the message.
When reassembling the full message, we try to link skbs from the "first
fragment" clone using the frag_list. However, since the frag_list is shared
between two clones in this rare situation, we end up setting the frag_list
pointer of the second fragment to point to itself. This causes
sctp_skb_pull() to potentially recurse indefinitely.
Proposed solution is to make a copy of the skb when attempting to link
things using frag_list.
Signed-off-by: Vladislav Yasevich <vladsilav.yasevich@hp.com> Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Sat, 6 May 2006 00:02:09 +0000 (17:02 -0700)]
[SCTP]: Allow spillover of receive buffer to avoid deadlock.
This patch fixes a deadlock situation in the receive path by allowing
temporary spillover of the receive buffer.
- If the chunk we receive has a tsn that immediately follows the ctsn,
accept it even if we run out of receive buffer space and renege data with
higher TSNs.
- Once we accept one chunk in a packet, accept all the remaining chunks
even if we run out of receive buffer space.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Mark Butler <butlerm@middle.net> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Pitre [Fri, 5 May 2006 21:32:24 +0000 (22:32 +0100)]
[ARM] 3500/1: fix PXA27x DMA allocation priority
Patch from Nicolas Pitre
Intel PXA27x developers manual section 5.4.1.1 lists a priority
distribution for the DMA channels differently than what the code
currently assumes. This patch fixes that.
Noticed by Simon Vogl <vogl@soft.uni-linz.ac.at>
Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
George G. Davis [Fri, 5 May 2006 21:32:23 +0000 (22:32 +0100)]
[ARM] 3499/1: Fix VFP FPSCR corruption for double exception case
Patch from George G. Davis
The ARM VFP FPSCR register is corrupted when a condition flags modifying
VFP instruction is followed by a non-condition flags modifying VFP
instruction and both instructions raise exceptions. The fix is to
read the current FPSCR in between emulation of these two instructions
and use the current FPSCR value when handling the second exception.
Signed-off-by: George G. Davis <gdavis@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Chen, Kenneth W [Wed, 3 May 2006 18:53:43 +0000 (11:53 -0700)]
[IA64] strcpy returns NULL pointer and not destination pointer
Bob Picco noted that 6edfba1b33c701108717f4e036320fc39abe1912
dropped the -ffreestanding compiler flag from the top level
Makefile, which allows the compiler to substitute memcpy() in
places where strcpy() is used with a known size source string.
But the ia64 memcpy() returns 0 for success, and "bytes copied"
for failure.
Fix to return the address of the destination string (like
stdlibc version, and other architectures). There are no
places where ia64 specific code makes use of the non-standard
return value.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Russell King [Fri, 5 May 2006 16:57:52 +0000 (17:57 +0100)]
[BLOCK] Fix oops on removal of SD/MMC card
The block layer keeps a reference (driverfs_dev) to the struct
device associated with the block device, and uses it internally
for generating uevents in block_uevent.
Block device uevents include umounting the partition, which can
occur after the backing device has been removed.
Unfortunately, this reference is not counted. This means that
if the struct device is removed from the device tree, the block
layers reference will become stale.
Guard against this by holding a reference to the struct device
in add_disk(), and only drop the reference when we're releasing
the gendisk kobject - in other words when we can be sure that no
further uevents will be generated for this block device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Jens Axboe <axboe@suse.de>
Linus Torvalds [Thu, 4 May 2006 22:09:52 +0000 (15:09 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: Use the ibm,pa-features property if available
powerpc: Fix incorrect might_sleep in __get_user/__put_user on kernel addresses
[PATCH] ppc32 CPM_UART: fixes and improvements
[PATCH] ppc32 CPM_UART: Fixed break send on SCC
[PATCH] powerpc/kprobes: fix singlestep out-of-line
[PATCH] powerpc/pseries: avoid crash in PCI code if mem system not up
Linus Torvalds [Thu, 4 May 2006 21:52:43 +0000 (14:52 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3490/1: i.MX: move uart resources to board files
[ARM] 3488/1: make icedcc_putc do the right thing
[ARM] 3487/1: IXP4xx: Support non-PCI systems
[ARM] 3486/1: Mark memory as clobbered by the ARM _syscallX() macros
Russell King [Thu, 4 May 2006 17:22:51 +0000 (18:22 +0100)]
[MMC] Move set_ios debugging into mmc.c
Rather than having every driver duplicate the set_ios debugging,
provide a single version in mmc.c which can be expanded as we
add additional functionality.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sascha Hauer [Thu, 4 May 2006 13:07:42 +0000 (14:07 +0100)]
[ARM] 3490/1: i.MX: move uart resources to board files
Patch from Sascha Hauer
This patch moves the i.MX uart resources and the gpio pin setup to the
board files. This allows the boards to decide how many internal uarts
are connected to the outside world and whether they use rts/cts or
not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jens Axboe [Thu, 4 May 2006 07:13:49 +0000 (09:13 +0200)]
[PATCH] compat_sys_vmsplice: one-off in UIO_MAXIOV check
nr_segs may not be > UIO_MAXIOV, however it may be equal to. This makes
the behaviour identical to the real sys_vmsplice(). The other foov
syscalls also agree that this is the way to go.
This patch fixes hello messages sent when a node is a level 1
router. Slightly contrary to the spec (maybe) VMS ignores hello
messages that do not name level2 routers that it also knows about.
So, here we simply name all the routers that the node knows about
rather just other level1 routers. (I hope the patch is clearer than
the description. sorry).
Signed-off-by: Patrick Caulfield <patrick@tykepenguin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Thu, 4 May 2006 06:31:35 +0000 (23:31 -0700)]
[TCP]: Fix sock_orphan dead lock
Calling sock_orphan inside bh_lock_sock in tcp_close can lead to dead
locks. For example, the inet_diag code holds sk_callback_lock without
disabling BH. If an inbound packet arrives during that admittedly tiny
window, it will cause a dead lock on bh_lock_sock. Another possible
path would be through sock_wfree if the network device driver frees the
tx skb in process context with BH enabled.
We can fix this by moving sock_orphan out of bh_lock_sock.
The tricky bit is to work out when we need to destroy the socket
ourselves and when it has already been destroyed by someone else.
By moving sock_orphan before the release_sock we can solve this
problem. This is because as long as we own the socket lock its
state cannot change.
So we simply record the socket state before the release_sock
and then check the state again after we regain the socket lock.
If the socket state has transitioned to TCP_CLOSE in the time being,
we know that the socket has been destroyed. Otherwise the socket is
still ours to keep.
Note that I've also moved the increment on the orphan count forward.
This may look like a problem as we're increasing it even if the socket
is just about to be destroyed where it'll be decreased again. However,
this simply enlarges a window that already exists. This also changes
the orphan count test by one.
Considering what the orphan count is meant to do this is no big deal.
This problem was discoverd by Ingo Molnar using his lock validator.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Thu, 4 May 2006 06:26:20 +0000 (23:26 -0700)]
[ROSE]: Fix routing table locking in rose_remove_neigh.
The locking rule for rose_remove_neigh() are that the caller needs to
hold rose_neigh_list_lock, so we better don't take it yet again in
rose_neigh_list_lock.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jing Min Zhao <zhaojingmin@users.sourceforge.net> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 4 May 2006 06:17:11 +0000 (23:17 -0700)]
[NETFILTER]: H.323 helper: fix use of uninitialized data
When a Choice element contains an unsupported choice no error is returned
and parsing continues normally, but the choice value is not set and
contains data from the last parsed message. This may in turn lead to
parsing of more stale data and following crashes.
Fixes a crash triggered by testcase 0003243 from the PROTOS c07-h2250v4
testsuite following random other testcases:
Jens Axboe [Wed, 3 May 2006 08:58:22 +0000 (10:58 +0200)]
[PATCH] splice: redo page lookup if add_to_page_cache() returns -EEXIST
This can happen quite easily, if several processes are trying to splice
the same file at the same time. It's not a failure, it just means someone
raced with us in allocating this file page. So just dump the allocated
page and relookup the original.
Jens Axboe [Wed, 3 May 2006 08:35:26 +0000 (10:35 +0200)]
[PATCH] splice: LRU fixups
Nick says that the current construct isn't safe. This goes back to the
original, but sets PIPE_BUF_FLAG_LRU on user pages as well as they all
seem to be on the LRU in the first place.
Mingming Cao [Thu, 4 May 2006 02:55:12 +0000 (19:55 -0700)]
[PATCH] ext3: multile block allocate little endian fixes
Some places in ext3 multiple block allocation code (in 2.6.17-rc3) don't
handle the little endian well. This was resulting in *wrong* block numbers
being assigned to in-memory block variables and then stored on disk
eventually. The following patch has been verified to fix an ext3
filesystem failure when run ltp test on a 64 bit machine.
Signed-off-by; Mingming Cao <cmm@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brent Casavant [Thu, 4 May 2006 02:55:10 +0000 (19:55 -0700)]
[PATCH] Altix: correct ioc4 port order
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Brent Casavant <bcasavan@sgi.com> Cc: Pat Gefre <pfg@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mark gross [Thu, 4 May 2006 02:55:07 +0000 (19:55 -0700)]
[PATCH] EDAC Coexistence with BIOS
Address the issue of EDAC/BIOS coexistence for the e752x chip-sets.
We have found a problem where the BIOS will start the system with the error
registers (dev0:fun1) hidden and assuming it has exclusive access to them.
The edac driver violates this assumption.
The workaround this patch offers is to honor the hidden-ness as an
indication that it is not safe to use those registers.
Signed-off-by: Mark Gross <mark.gross@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Thu, 4 May 2006 02:55:03 +0000 (19:55 -0700)]
[PATCH] uml: change timer initialization
inet_init, which schedules, is called before the UML timer_init, which sets
up the timer. The result is the interval timers being manipulated before
the appropriate signal handlers are established, causing unhandled timers.
This is fixed by making timer_init be called earlier.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stephen Smalley [Wed, 3 May 2006 14:52:36 +0000 (10:52 -0400)]
[PATCH] selinux: Clear selinux_enabled flag upon runtime disable.
Clear selinux_enabled flag upon runtime disable of SELinux by userspace,
and make sure it is defined even if selinux= boot parameter support is
not enabled in configuration.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Acked-by: James Morris <jmorris@namei.org> Tested-by: Jon Smirl <jonsmirl@gmail.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Mackerras [Wed, 3 May 2006 13:04:37 +0000 (23:04 +1000)]
[PATCH] powerpc: Use the ibm,pa-features property if available
Forthcoming IBM machines will have a "ibm,pa-features" property on CPU
nodes, that contains bits indicating which optional architecture
features are implemented by the CPU. This adds code to use the
property, if present, to update our CPU feature bitmaps. Note that
this means we can both set and clear feature bits based on what
the firmware tells us.
This is based on a patch by Will Schmidt <willschm@us.ibm.com>.
Paul Mackerras [Wed, 3 May 2006 13:02:04 +0000 (23:02 +1000)]
powerpc: Fix incorrect might_sleep in __get_user/__put_user on kernel addresses
We have a case where __get_user and __put_user can validly be used
on kernel addresses in interrupt context - namely, the alignment
exception handler, as our get/put_unaligned just do a single access
and rely on the alignment exception handler to fix things up in the
rare cases where the cpu can't handle it in hardware. Thus we can
get alignment exceptions in the network stack at interrupt level.
The alignment exception handler does a __get_user to read the
instruction and blows up in might_sleep().
Since a __get_user on a kernel address won't actually ever sleep,
this makes the might_sleep conditional on the address being less
than PAGE_OFFSET.
A number of small issues are fixed, and added the header file, missed from the
original series. With this, driver should be pretty stable as tested among
both platform-device-driven and "old way" boards. Also added missing GPL
statement , and updated year field on existing ones to reflect
code update.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
SCC uart sends a break sequence each time it is stopped with the
CPM_CR_STOP_TX command. That means that each time an application closes the
serial device, a break is transmitted. To fix this, graceful tx stop is
issued for SCC.
Signed-off-by: David Jander <david.jander@protonic.nl> Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently single-step inline if the instruction on which a kprobe is
inserted is a trap variant.
- variants (such as tdnei, used by BUG()) typically evaluate a condition
and cause a trap only if the condition is satisfied.
- kprobes uses the unconditional "trap" (0x7fe00008) and single-stepping
again on this instruction, resulting in another trap without
evaluating the condition is obviously incorrect.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc/pseries: avoid crash in PCI code if mem system not up
The powerpc code is currently performing PCI setup before memory
initialization. PCI setup touches PCI config space registers. If the PCI
card is bad, this will evoke an error, which currrently can't be handled,
as the PCI error recovery code expects kmalloc() to be functional. This
patch will cause the system to punt instead of crashing with
Patrick McHardy [Tue, 2 May 2006 21:23:07 +0000 (23:23 +0200)]
[NETFILTER] SCTP conntrack: fix infinite loop
fix infinite loop in the SCTP-netfilter code: check SCTP chunk size to
guarantee progress of for_each_sctp_chunk(). (all other uses of
for_each_sctp_chunk() are preceded by do_basic_checks(), so this fix
should be complete.)
Based on patch from Ingo Molnar <mingo@elte.hu>
CVE-2006-1527
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / karo-tx-linux.git / log