Maxime Ripard [Mon, 27 Jul 2015 11:17:09 +0000 (12:17 +0100)]
nvmem: sunxi: Move the SID driver to the nvmem framework
Now that we have the nvmem framework, we can consolidate the common
driver code. Move the driver to the framework, and hopefully, it will
fix the sysfs file creation race.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[srinivas.kandagatla: Moved to regmap based EEPROM framework] Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds QFPROM support driver which is used by other drivers
like thermal sensor and cpufreq.
On MSM parts there are some efuses (called qfprom) these fuses store
things like calibration data, speed bins.. etc. Drivers like cpufreq,
thermal sensors would read out this data for configuring the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds read/write apis which are based on nvmem_device. It is
common that the drivers like omap cape manager or qcom cpr driver to
access bytes directly at particular offset in the eeprom and not from
nvmem cell info in DT. These driver would need to get access to the nvmem
directly, which is what these new APIS provide.
These wrapper apis would help such users to avoid code duplication in
there drivers and also avoid them reading a big eeprom blob and parsing
it internally in there driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds just consumers part of the framework just to enable easy
review.
Up until now, nvmem drivers were stored in drivers/misc, where they all
had to duplicate pretty much the same code to register a sysfs file,
allow in-kernel users to access the content of the devices they were
driving, etc.
This was also a problem as far as other in-kernel users were involved,
since the solutions used were pretty much different from on driver to
another, there was a rather big abstraction leak.
This introduction of this framework aims at solving this. It also
introduces DT representation for consumer devices to go get the data they
require (MAC Addresses, SoC/Revision ID, part numbers, and so on) from
the nvmems.
Having regmap interface to this framework would give much better
abstraction for nvmems on different buses.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Maxime Ripard: intial version of the framework] Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvmem: Add a simple NVMEM framework for nvmem providers
This patch adds just providers part of the framework just to enable easy
review.
Up until now, NVMEM drivers like eeprom were stored in drivers/misc,
where they all had to duplicate pretty much the same code to register
a sysfs file, allow in-kernel users to access the content of the devices
they were driving, etc.
This was also a problem as far as other in-kernel users were involved,
since the solutions used were pretty much different from on driver to
another, there was a rather big abstraction leak.
This introduction of this framework aims at solving this. It also
introduces DT representation for consumer devices to go get the data
they require (MAC Addresses, SoC/Revision ID, part numbers, and so on)
from the nvmems.
Having regmap interface to this framework would give much better
abstraction for nvmems on different buses.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Maxime Ripard: intial version of eeprom framework] Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parport_find_base() will implicitly do parport_get_port() which
increases the refcount. Then parport_register_device() will again
increment the refcount. But while unloading the module we are only
doing parport_unregister_device() decrementing the refcount only once.
We add an parport_put_port() to neutralize the effect of
parport_get_port().
Mark Brown [Fri, 31 Jul 2015 15:37:30 +0000 (09:37 -0600)]
coresight: Fix implicit inclusion of linux/sched.h
The patch "Coresight: Add an interface for supporting ETM3/4 Context ID
tracing" adds uses of find_task_by_vpid() and task_pid_nr() from
linux/sched.h but does not include that header causing build errors in
at least an ARM allmodconfig where it is not implicitly included. Add an
explicit include to fix that.
Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
coresight-etm3x: Support context-ID tracing when PID namespace is enabled
The Coresight ETM drivers already support context-ID tracing, but it won't
work when PID namespace is enabled. This is because when using PID
namespace a process id (ie. VPID) seen from the current namespace differs
from the id (ie. PID) seen by kernel.
So when users write the process id seen by themselves to ETM, there needs
to be a translation from VPID to PID, as such ETM drivers will write the
PID into the Context ID register correctly.
Coresight: Add an interface for supporting ETM3/4 Context ID tracing
If PID namespace is enabled, everytime users configure the Context ID
register to trace the specific process, there needs to be a translation
between the real PID seen from the kernel and VPID seen from the
namespace in which the user's process resides .
This patch just adds the translation interface for ETMs.
coresight-etm4x: Change the name of the ctxid_val to ctxid_pid
'ctxid_val' array was used to store the value of ETM context ID comparator
which actually stores the process ID to be traced, so using 'ctxid_pid' as
its name instead make it easier to understand.
This patch also changes the ABI, it is normally not allowed, but
fortunately it is a testing ABI and very new for now. Nevertheless,
if you don't think it should be changed, we could always add an alias
for userspace.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> Reviewed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
coresight-etm3x: Change the name of the ctxid_val to ctxid_pid
'ctxid_val' array was used to store the value of ETM context ID comparator
which actually stores the process ID to be traced, so using 'ctxid_pid' as
its name instead make it easier to understand.
This patch also changes the ABI, it is normally not allowed, but
fortunately it is a testing ABI and very new for now. Nevertheless,
if you don't think it should be changed, we could always add an alias
for userspace.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> Reviewed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
coresight: replicator: Use builtin_platform_driver()
Macro builtin_platform_driver can be used for builtin drivers
that don't do anything in driver init. This file depends on
Kconfig CONFIG_CORESIGHT_LINKS_AND_SINKS which eventually
depends on CORESIGHT. Both CONFIG_CORESIGHT_LINKS_AND_SINKS and
CORESIGHT are bool. So, use builtin_platform_driver and remove
some boilerplate code.
Also, remove header file init.h as functionality like module_init
and module_exit is now relocated to module.h.
@b depends on a@
identifier e, a.x;
@@
-static e(...) { platform_driver_unregister(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_platform_driver;
@@
-module_exit(e);
+module_platform_driver(x);
Destroy uio_idr on module exit, reclaiming the allocated memory.
This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@
This binding is horrible and never should have been merged. It is not
documented nor are there any in tree users, so reverting it will not
break anything we care about. Lets revert it before we do have users.
The problems with it are:
- It is not documented.
- The GPIO connection is described with a custom property and uses Linux
GPIO numbering.
- The UART connection is described using the Linux tty device name.
Cc: Gigi Joseph <gigi.joseph@ti.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Boyd [Tue, 16 Jun 2015 18:37:16 +0000 (11:37 -0700)]
spmi: Select IRQ_DOMAIN instead of depend on it
IRQ_DOMAIN is a hidden config option, so depending on it doesn't
make any sense. Select the config option because it's required to
compile this driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reviewed-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ankit Gupta [Mon, 22 Jun 2015 22:38:46 +0000 (16:38 -0600)]
spmi: add command tracepoints for SPMI
Add tracepoints to retrieve information about read, write
and non-data commands. For performance measurement support
tracepoints are added at the beginning and at the end of
transfers. Following is a list showing the new tracepoint
events. The "cmd" parameter here represents the opcode, SID,
and full 16-bit address.
spmi_write_begin: cmd and data buffer.
spmi_write_end : cmd and return value.
spmi_read_begin : cmd.
spmi_read_end : cmd, return value and data buffer.
spmi_cmd : cmd.
The reason that cmd appears at both the beginning and at
the end event is that SPMI drivers can request commands
concurrently. cmd helps in matching the corresponding
events.
Eli Billauer [Wed, 5 Aug 2015 10:03:26 +0000 (13:03 +0300)]
char: xillybus: Allow 64-bit DMA on PCIe interface
Until now, only 32-bit DMA addressing was allowed, following a report on
some old Intel machine that dropped 64-bit PCIe packets, even though
pci_set_dma_mask() was successful with DMA_BIT_MASK(64).
But then came TI's Keystone II chip (ARM Cortex A15 + DSPs), which refuses
32-bit DMA addressing (for good reasons). So 64-bit DMA is allowed as a
fallback option.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: use cpu_hotplug_enable/disable
Commit e513229b4c38 ("Drivers: hv: vmbus: prevent cpu offlining on newer
hypervisors") was altering smp_ops.cpu_disable to prevent CPU offlining.
We can bo better by using cpu_hotplug_enable/disable functions instead of
such hard-coding.
Reported-by: Radim Kr.má <rkrcmar@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hyper-V module needs to disable cpu hotplug (offlining) as there is no
support from hypervisor side to reassign already opened event channels
to a different CPU. Currently it is been done by altering
smp_ops.cpu_disable but it is hackish.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpu-hotplug: convert cpu_hotplug_disabled to a counter
As a prerequisite to exporting cpu_hotplug_enable/cpu_hotplug_disable
functions to modules we need to convert cpu_hotplug_disabled to a counter
to properly support disable -> disable -> enable call sequences. E.g.
after Hyper-V vmbus module (which is supposed to be the first user of
exported cpu_hotplug_enable/cpu_hotplug_disable) did cpu_hotplug_disable()
hibernate path calls disable_nonboot_cpus() and if we hit an error in
_cpu_down() enable_nonboot_cpus() will be called on the failure path (thus
making cpu_hotplug_disabled = 0 and leaving cpu hotplug in 'enabled'
state). Same problem is possible if more than 1 module use
cpu_hotplug_disable/cpu_hotplug_enable on their load/unload paths. When
one of these modules is been unloaded it is logical to leave cpu hotplug
in 'disabled' state.
To support the change we need to increse cpu_hotplug_disabled counter
in disable_nonboot_cpus() unconditionally as all users of
disable_nonboot_cpus() are supposed to do enable_nonboot_cpus() in case
an error was returned.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dexuan Cui [Wed, 5 Aug 2015 07:52:45 +0000 (00:52 -0700)]
Drivers: hv: vmbus: document the VMBus sysfs files
The 4 sysfs files should be stable ABIs to the user space.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dexuan Cui [Wed, 5 Aug 2015 07:52:44 +0000 (00:52 -0700)]
tools: hv: add a python script lsvmbus to list VMBus devices
By default lsvmbus lists all the devices in the VMBus.
With -v or -vv, more information is printed, including the VMBus
Rel_ID, class ID, device ID and which channel is bound to which
virtual processor, etc.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dexuan Cui [Wed, 5 Aug 2015 07:52:43 +0000 (00:52 -0700)]
Drivers: hv: vmbus: add a sysfs attr to show the binding of channel/VP
This is useful to analyze performance issue.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: Implement a clocksource based on the TSC page
The current Hyper-V clock source is based on the per-partition reference counter
and this counter is being accessed via s synthetic MSR - HV_X64_MSR_TIME_REF_COUNT.
Hyper-V has a more efficient way of computing the per-partition reference
counter value that does not involve reading a synthetic MSR. We implement
a time source based on this mechanism.
Tested-by: Vivek Yadav <vyadav@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christopher Oo [Wed, 5 Aug 2015 07:52:40 +0000 (00:52 -0700)]
Drivers: hv_vmbus: Fix signal to host condition
Fixes a bug where previously hv_ringbuffer_read would pass in the old
number of bytes available to read instead of the expected old read index
when calculating when to signal to the host that the ringbuffer is empty.
Since the previous write size is already saved, also changes the
hv_need_to_signal_on_read to use the previously read value rather than
recalculating it.
Signed-off-by: Christopher Oo <t-chriso@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dexuan Cui [Wed, 5 Aug 2015 07:52:39 +0000 (00:52 -0700)]
Drivers: hv: vmbus: Further improve CPU affiliation logic
Keep track of CPU affiliations of sub-channels within the scope of the primary
channel. This will allow us to better distribute the load amongst available
CPUs.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: Improve the CPU affiliation for channels
The current code tracks the assigned CPUs within a NUMA node in the context of
the primary channel. So, if we have a VM with a single NUMA node with 8 VCPUs, we may
end up unevenly distributing the channel load. Fix the issue by tracking affiliations
globally.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jake Oshins [Wed, 5 Aug 2015 07:52:37 +0000 (00:52 -0700)]
drivers:hv: Move MMIO range picking from hyper_fb to hv_vmbus
This patch deletes the logic from hyperv_fb which picked a range of MMIO space
for the frame buffer and adds new logic to hv_vmbus which picks ranges for
child drivers. The new logic isn't quite the same as the old, as it considers
more possible ranges.
Signed-off-by: Jake Oshins <jakeo@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jake Oshins [Wed, 5 Aug 2015 07:52:36 +0000 (00:52 -0700)]
drivers:hv: Modify hv_vmbus to search for all MMIO ranges available.
This patch changes the logic in hv_vmbus to record all of the ranges in the
VM's firmware (BIOS or UEFI) that offer regions of memory-mapped I/O space for
use by paravirtual front-end drivers. The old logic just found one range
above 4GB and called it good. This logic will find any ranges above 1MB.
It would have been possible with this patch to just use existing resource
allocation functions, rather than keep track of the entire set of Hyper-V
related MMIO regions in VMBus. This strategy, however, is not sufficient
when the resource allocator needs to be aware of the constraints of a
Hyper-V virtual machine, which is what happens in the next patch in the series.
So this first patch exists to show the first steps in reworking the MMIO
allocation paths for Hyper-V front-end drivers.
Signed-off-by: Jake Oshins <jakeo@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With well over 200+ users of this api, there are a mere 12 users that
actually checked the return value of this function. And all of them
really didn't do anything with that information as the system or module
was shutting down no matter what.
So stop pretending like it matters, and just return void from
misc_deregister(). If something goes wrong in the call, you will get a
WARNING splat in the syslog so you know how to fix up your driver.
Other than that, there's nothing that can go wrong.
Cc: Alasdair Kergon <agk@redhat.com> Cc: Neil Brown <neilb@suse.com> Cc: Oleg Drokin <oleg.drokin@intel.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Christine Caulfield <ccaulfie@redhat.com> Cc: David Teigland <teigland@redhat.com> Cc: Mark Fasheh <mfasheh@suse.com> Acked-by: Joel Becker <jlbec@evilplan.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: Consider ND NIC in binding channels to CPUs
We cycle through all the "high performance" channels to distribute
load across the available CPUs. Process the NetworkDirect as a
high performance device.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Denis V. Lunev [Sat, 1 Aug 2015 23:08:20 +0000 (16:08 -0700)]
mshyperv: fix recognition of Hyper-V guest crash MSR's
Hypervisor Top Level Functional Specification v3.1/4.0 notes that cpuid
(0x40000003) EDX's 10th bit should be used to check that Hyper-V guest
crash MSR's functionality available.
This patch should fix this recognition. Currently the code checks EAX
register instead of EDX.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: Permit sending of packets without payload
The guest may have to send a completion packet back to the host.
To support this usage, permit sending a packet without a payload -
we would be only sending the descriptor in this case.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Ng [Sat, 1 Aug 2015 23:08:13 +0000 (16:08 -0700)]
Drivers: hv: balloon: Enable dynamic memory protocol negotiation with Windows 10 hosts
Support Win10 protocol for Dynamic Memory. Thia patch allows guests on Win10 hosts
to hot-add memory even when dynamic memory is not enabled on the guest.
Signed-off-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kzalloc() return value check was accidentally lost in 11bc3a5fa91f:
"Drivers: hv: kvp: convert to hv_utils_transport" commit.
We don't need to reset kvp_transaction.state here as we have the
kvp_timeout_func() timeout function and in case we're in OOM situation
it is preferable to wait.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: prefer 'die' notification chain to 'panic'
current_pt_regs() sometimes returns regs of the userspace process and in
case of a kernel crash this is not what we need to report. E.g. when we
trigger crash with sysrq we see the following:
...
RIP: 0010:[<ffffffff815b8696>] [<ffffffff815b8696>] sysrq_handle_crash+0x16/0x20
RSP: 0018:ffff8800db0a7d88 EFLAGS: 00010246
RAX: 000000000000000f RBX: ffffffff820a0660 RCX: 0000000000000000
...
at the same time current_pt_regs() give us:
ip=7f899ea7e9e0, ax=ffffffffffffffda, bx=26c81a0, cx=7f899ea7e9e0, ...
These registers come from the userspace process triggered the crash. As we
don't even know which process it was this information is rather useless.
When kernel crash happens through 'die' proper regs are being passed to
all receivers on the die_chain (and panic_notifier_list is being notified
with the string passed to panic() only). If panic() is called manually
(e.g. on BUG()) we won't get 'die' notification so keep the 'panic'
notification reporter as well but guard against double reporting.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Full kernel hang is observed when kdump kernel starts after a crash. This
hang happens in vmbus_negotiate_version() function on
wait_for_completion() as Hyper-V host (Win2012R2 in my testing) never
responds to CHANNELMSG_INITIATE_CONTACT as it thinks the connection is
already established. We need to perform some mandatory minimalistic
cleanup before we start new kernel.
Reported-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: don't do hypercalls when hypercall_page is NULL
At the very late stage of kexec a driver (which are not being unloaded) can
try to post a message or signal an event. This will crash the kernel as we
already did hv_cleanup() and the hypercall page is NULL.
Move all common (between 32 and 64 bit code) declarations to the beginning
of the do_hypercall() function. Unfortunately we have to write the
!hypercall_page check twice to not mix declarations and code.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When general-purpose kexec (not kdump) is being performed in Hyper-V guest
the newly booted kernel fails with an MCE error coming from the host. It
is the same error which was fixed in the "Drivers: hv: vmbus: Implement
the protocol for tearing down vmbus state" commit - monitor pages remain
special and when they're being written to (as the new kernel doesn't know
these pages are special) bad things happen. We need to perform some
minimalistic cleanup before booting a new kernel on kexec. To do so we
need to register a special machine_ops.shutdown handler to be executed
before the native_machine_shutdown(). Registering a shutdown notification
handler via the register_reboot_notifier() call is not sufficient as it
happens to early for our purposes. machine_ops is not being exported to
modules (and I don't think we want to export it) so let's do this in
mshyperv.c
The minimalistic cleanup consists of cleaning up clockevents, synic MSRs,
guest os id MSR, and hypercall MSR.
Kdump doesn't require all this stuff as it lives in a separate memory
space.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kexec: define kexec_in_progress in !CONFIG_KEXEC case
If some piece of code wants to check kexec_in_progress it has to be put
in #ifdef CONFIG_KEXEC block to not break the build in !CONFIG_KEXEC
case. Overcome this limitation by defining kexec_in_progress to false.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: remove hv_synic_free_cpu() call from hv_synic_cleanup()
We already have hv_synic_free() which frees all per-cpu pages for all
CPUs, let's remove the hv_synic_free_cpu() call from hv_synic_cleanup()
so it will be possible to do separate cleanup (writing to MSRs) and final
freeing. This is going to be used to assist kexec.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Tue, 4 Aug 2015 11:30:11 +0000 (14:30 +0300)]
mei: remove check on pm_runtime_active in __mei_cl_disconnect
Remove bogus check on pm_runtime_active that prevented
disconnection from a client in case the device was resuming
from power gating but not yet active.
mei: me: d0i3: exit d0i3 on driver start and enter it on stop
A BIOS may put the device in d0i3 on platform initialization so it won’t
consume power even if the driver is not present, in turn the driver has
to wake up the devices on load in order to perform the initialization
sequence and move it back to low power state on driver remove.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework mei power gating state machine to support entry and exit to and
from D0i3 power state.
The choice between legacy and D0i3 routines is conditioned on
d0i3_supported flag.
The patch introduces warning:
drivers/misc/mei/hw-me.c:901:12: warning: ‘mei_me_d0i3_enter’ defined but not used [-Wunused-function]
it will go away in consequent patch
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before adding support for D0i3 we need to reorganize the hbm pg handling
Move HBM PG response code to dedicated functions in order to unclutter
hbm command switch.
Add check for the right system state before message processing and
return -EPROTO in state mismatch case.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
D0i3 adds additional interrupt reason bit, therefore we add a variable
intr_source to save the interrupt causes for further dispatching.
The interrupt cause is saved in the irq quick handler to achieve
unified behavior for both MSI enabled and shared interrupt platforms.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei: hbm: add new error code MEI_CL_CONN_NOT_ALLOWED
The device can return error 5 (NOT_ALLOWED) on connection attempt.
This error can happen if:
1. An another connection attempt is in progress
2. There is an attempt to connect a fixed (connectionless) client
3. The number of available connections is exceeded (new in HBM 2.0)
We should not hit that error unless there is an internal book keeping
hiccup except option (3), therefore we translate the error code
to errno EBUSY;
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable drivers on mei client bus to subscribe
to asynchronous event notifications.
Introduce events_mask to the existing callback infrastructure
so it is possible to handle both RX and event notification.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Sun, 26 Jul 2015 06:54:21 +0000 (09:54 +0300)]
mei: support polling for event notification
Polling on priority events is translated on waiting for event
notification. One need to enable notification prior for
calling select or poll system call otherwise process
will not wait.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Sun, 26 Jul 2015 06:54:20 +0000 (09:54 +0300)]
mei: add async event notification ioctls
Add ioctl IOCTL_MEI_NOTIFY_SET for enabling and disabling
async event notification.
Add ioctl IOCTL_MEI_NOTIFY_GET for receiving and acking
an event notification.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Sun, 26 Jul 2015 06:54:16 +0000 (09:54 +0300)]
mei: implement async notification hbm messages
Implement sending and reception handlers for the
async event notification hbm commands.
Add client notification book keeping data required for the messages
notify_en to indicate whether notification is enabled
notify_ev to indicate whether an event is pending
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Sun, 26 Jul 2015 06:54:15 +0000 (09:54 +0300)]
mei: define async notification hbm commands
FW has gained new capability where a FW client can asynchronously
notify the host that an event has occurred in its process.
The notification doesn't provide any data and host may need to query
further the FW client in order to get details of the event.
Host can subscribe or unsubscribe to the event notification via
designated HBM commands, and also the notification is carried on
a new HBM command.
This patch adds definitions of asynchronous notification HBM commands.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the FW with HBM version >= 2.0 we don't need to reset the whole
device in case of a particular client failing to connect, it is enough
to send disconnect a request to bring the device to the stable state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 18:37:12 +0000 (21:37 +0300)]
mei: support for dynamic clients
HBM version 2.0 and above allows ME clients in the system to
register/unregister after the system is fully initialized.
Clients may be added or removed after enum_resp message was
received
1. To preserve backward compatibility the driver can opt-in to receive
client add messages by setting allow_add field in enum_req
2. A new client is added upon reception of MEI_HBM_ADD_CLIENT_REQ_CMD
3. A client is removed in a lazy manner when connection request
respond with MEI_HBMS_CLIENT_NOT_FOUND status
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 12:08:47 +0000 (15:08 +0300)]
mei: bus: link client devices instead of host clients
MEI bus was designed around nfc and was hard to extend.
Instead of the hard coded way of adding the devices on the mei bus
we scan the whole me client list and create a device for each
eligible me client (mei_cl_bus_rescan); currently we support
only clients with single connection and fixed address clients.
NFC radio name detection is run as a fixup routine
The patch replaces handling the device list based on struct me_cl
to device list based on me_cl_devices. The creating a connection
is pushed from the device creation time to device enablement.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 12:08:43 +0000 (15:08 +0300)]
mei: bus: enable running fixup routines before device registration
Split the device registration into allocation and device struct
initialization, device setup, and the final device registration.
This why it is possible to run fixups and quirks during the setup stage
on an initialized device. Each fixup routine effects do_match flag.
If the flag is set to false at the end the device won't be
registered on the bus.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 12:08:42 +0000 (15:08 +0300)]
mei: bus: add me client device list infrastructure
Instead of holding the list of host clients (me_cl)
we want to keep the list me client devices (mei_cl_device)
This way we can create host to me client connection only when needed.
Add list head to mei_cl_device and cl_bus_lock
Add bus_added flag to the me client (mei_me_client) to track if
the appropriate mei_cl_device was already created and is_added
flag to mei_cl_device to track if it was already added to the device
list across the bus rescans
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 12:08:41 +0000 (15:08 +0300)]
mei: bus: add reference to bus device in struct mei_cl_client
Add reference to the bus device (mei_device) for easier access.
To ensures that referencing cldev->bus is valid during cldev life time
we increase the bus ref counter on a client device creation and drop it
on the device release.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 12:08:40 +0000 (15:08 +0300)]
mei: bus: revamp probe and remove functions
Instead of generating device id on the fly during probing we
find the matching id entry on the device id table.
Get bus the module reference counter so it cannot
be unloaded after the driver has bounded to the client
device
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 12:08:39 +0000 (15:08 +0300)]
mei: bus: revamp device matching
mei_cl_device_match now calls mei_cl_device_find that returns
the matching device id in the device id table.
We will utilize the mei_cl_device_find during probing
to locate the matching entry.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 12:08:37 +0000 (15:08 +0300)]
mei: bus: don't enable events implicitly in device enable
Do not enable events implicitly in mei_cl_enable_device, it should be
done explicitly using mei_cl_register_event_cb so the events
are enabled only when needed.
The NFC drivers has been already using it that way so no need for
further changes just remove the code from mei_cl_enable_device.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Thu, 23 Jul 2015 12:08:34 +0000 (15:08 +0300)]
mei: bus: rename nfc.c to bus-fixup.c
The bus-fixup.c will be a place for fixups and quirks
for all types of me client devices.
As for now it contians only the fixup for setting
the nfc device name on the me client bus.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-beck.git / log