Jeff Layton [Thu, 28 Jul 2011 16:48:26 +0000 (12:48 -0400)]
cifs: fix compiler warning in CIFSSMBQAllEAs
The recent fix to the above function causes this compiler warning to pop
on some gcc versions:
CC [M] fs/cifs/cifssmb.o
fs/cifs/cifssmb.c: In function ‘CIFSSMBQAllEAs’:
fs/cifs/cifssmb.c:5708: warning: ‘ea_name_len’ may be used uninitialized in
this function
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
CC arch/mips/pmc-sierra/msp71xx/msp_irq.o
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:112:2: error: request for member ‘flags’ in something not a structure or union
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:118:2: error: request for member ‘flags’ in something not a structure or union
make[4]: *** [arch/mips/pmc-sierra/msp71xx/msp_irq.o] Error 1
do_signal() does __put_user() which can fault, resulting in a
might_sleep() warning in down_read(&mm->mmap_sem) and a "scheduling
while atomic" warning when mmap_sem is contented. On swarm this also
results in:
WARNING: at kernel/smp.c:459 smp_call_function_many+0x148/0x398()
Modules linked in:
Call Trace:
Enable interrupts in do_notify_resume before delivering signals.
[ralf@linux-mips.org: Reported and original fix by tglx but I wanted to
minimize the amount of code being run with interrupts disabled so I moved
the local_irq_disable() call right into do_notify_resume. Which is saner
than doing it in entry.S.]
Reported-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: Loongson: Mark cascade interrupts IRQF_NO_THREAD
There are two cascade interrupts in Loongson machines, one for bonito
northbridge, another for the 8259A controller in the southbridge. Both
want to be non threaded.
MIPS: Mark cascade and low level interrupts IRQF_NO_THREAD
Mark interrupts with no_action handler, cascade interrupts, low level
interrupts (bus error, halt ..) with IRQF_NO_THREAD to exclude them
from forced threading.
Thomas Gleixner [Thu, 28 Jul 2011 15:21:43 +0000 (16:21 +0100)]
MIPS: ftrace: Fix the CONFIG_DYNAMIC_FTRACE=n compile
arch/mips/kernel/ftrace.c: In function ‘ftrace_get_parent_ra_addr’:
arch/mips/kernel/ftrace.c:212: error: implicit declaration of function ‘in_kernel_space’
arch/mips/kernel/ftrace.c: In function ‘prepare_ftrace_return’:
arch/mips/kernel/ftrace.c:314: error: ‘MCOUNT_OFFSET_INSNS’ undeclared (first use in this function)
arch/mips/kernel/ftrace.c:314: error: (Each undeclared identifier is reported only once
arch/mips/kernel/ftrace.c:314: error: for each function it appears in.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2634/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pci/pci-rc32434.c: In function 'rc32434_pci_init':
arch/mips/pci/pci-rc32434.c:217:16: error: 'rcrc32434_res_pci_io1' undeclared (first use in this function)
arch/mips/pci/pci-rc32434.c:217:16: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-rc32434.o] Error 1
Turns out this patch is producing many build errors with gcc 4.2. Based
on further testing with a test case extracted from the build errors found
further build errors and suboptimal generation even in violation of the
"R" constraint.
To make matters worse, the binutils changes also don't work quite as
intended so revert this patch for now.
MIPS: cache: Provide cache flush operations for XFS
Until now flush_kernel_vmap_range() and invalidate_kernel_vmap_range() did
not exist on MIPS resulting in heavy cache corruption on XFS filesystems.
Left for the post-3.0 time: optimization and make this work with highmem,
too. Since the combination of highmem + cache aliases atm doesn't work
this isn't a regression.
MIPS: SNI: Fix conflicting wrapper symbols for headers.
If Open Firmware / Device Tree support is enabled on a SNI RM kernel both
<asm/mipsprom.h> and <asm/prom.h> will be included into some .c files.
Since both headers use the same wrapper symbol only the inclusion of the
first file will have an effect but the 2nd file will be ignored resulting
in a build error.
After the recent cleanup of the register_*_smp_ops() functions msp71xx
wasn't fixed to include the now necessary header resulting in:
/home/ralf/src/linux/upstream-linus/arch/mips/pmc-sierra/msp71xx/msp_setup.c: In function ‘prom_init’:
/home/ralf/src/linux/upstream-linus/arch/mips/pmc-sierra/msp71xx/msp_setup.c:231:2: error: implicit declaration of function ‘register_vsmp_smp_ops’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
Triggered by pnx8550-jbs_defconfig and pnx8550-stb810_defconfig:
WARNING: vmlinux.o(.text+0xc0c): Section mismatch in reference from the function prom_getcmdline() to the variable .init.data:arcs_cmdline
The function prom_getcmdline() references
the variable __initdata arcs_cmdline.
This is often because prom_getcmdline lacks a __initdata
annotation or the annotation of arcs_cmdline is wrong.
WARNING: vmlinux.o(.text+0x3059f8): Section mismatch in reference from the function pcibios_plat_dev_init() to the function .devinit.text:request_bridge_irq()
The function pcibios_plat_dev_init() references
the function __devinit request_bridge_irq().
This is often because pcibios_plat_dev_init lacks a __devinit
annotation or the annotation of request_bridge_irq is wrong.
Fixing this one leads to:
WARNING: vmlinux.o(.text+0x1790): Section mismatch in reference from the function request_bridge_irq() to the function .devinit.text:register_bridge_irq()
The function request_bridge_irq() references
the function __devinit register_bridge_irq().
This is often because request_bridge_irq lacks a __devinit
annotation or the annotation of register_bridge_irq is wrong.
Jayachandran C [Tue, 21 Jun 2011 20:06:33 +0000 (01:36 +0530)]
MIPS: Netlogic: Specify architecture CFLAGS
Use -march=xlr if available, otherwise fallback to mips64. This allows
us to support compilation with MIPS toolchains which are not customized
for XLR.
[ralf@linux-mips.org: And more importantly it works around a gas bug in
binutils 2.21 which otherwise may result in an assertion failure building
arch/mips/kernel/genex.S. See
http://sourceware.org/bugzilla/show_bug.cgi?id=12915 for details.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2534/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
n2_crypto: Attach on Niagara-T3.
n2rng: Attach on Niagara-T3.
sparc: Detect and handle UltraSPARC-T3 cpu types.
sparc: Don't do expensive hypervisor PCR write unless necessary.
sparc: Add T3 sun4v cpu type and hypervisor group defines.
sparc: Don't leave sparc_pmu_type NULL on sun4v.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9aa31720b72e2bc2d665e24e1653c3e
gro: Only reset frag0 when skb can be pulled
...
Jeff Layton [Tue, 26 Jul 2011 22:23:47 +0000 (18:23 -0400)]
cifs: fix name parsing in CIFSSMBQAllEAs
cifs: fix name parsing in CIFSSMBQAllEAs
The code that matches EA names in CIFSSMBQAllEAs is incorrect. It
uses strncmp to do the comparison with the length limited to the
name_len sent in the response.
Problem: Suppose we're looking for an attribute named "foobar" and
have an attribute before it in the EA list named "foo". The
comparison will succeed since we're only looking at the first 3
characters. Fix this by also comparing the length of the provided
ea_name with the name_len in the response. If they're not equal then
it shouldn't match.
Reported-by: Jian Li <jiali@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Tue, 26 Jul 2011 16:21:17 +0000 (12:21 -0400)]
cifs: don't start signing too early
cifs: don't start signing too early
Sniffing traffic on the wire shows that windows clients send a zeroed
out signature field in a NEGOTIATE request, and send "BSRSPYL" in the
signature field during SESSION_SETUP. Make the cifs client behave the
same way.
It doesn't seem to make much difference in any server that I've tested
against, but it's probably best to follow windows behavior as closely as
possible here.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Tue, 26 Jul 2011 16:20:18 +0000 (12:20 -0400)]
cifs: advertise the right receive buffer size to the server
cifs: advertise the right receive buffer size to the server
Currently, we mirror the same size back to the server that it sends us.
That makes little sense. Instead we should be sending the server the
maximum buffer size that we can handle -- CIFSMaxBufSize minus the
4 byte RFC1001 header.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md: (75 commits)
md/raid10: handle further errors during fix_read_error better.
md/raid10: Handle read errors during recovery better.
md/raid10: simplify read error handling during recovery.
md/raid10: record bad blocks due to write errors during resync/recovery.
md/raid10: attempt to fix read errors during resync/check
md/raid10: Handle write errors by updating badblock log.
md/raid10: clear bad-block record when write succeeds.
md/raid10: avoid writing to known bad blocks on known bad drives.
md/raid10 record bad blocks as needed during recovery.
md/raid10: avoid reading known bad blocks during resync/recovery.
md/raid10 - avoid reading from known bad blocks - part 3
md/raid10: avoid reading from known bad blocks - part 2
md/raid10: avoid reading from known bad blocks - part 1
md/raid10: Split handle_read_error out from raid10d.
md/raid10: simplify/reindent some loops.
md/raid5: Clear bad blocks on successful write.
md/raid5. Don't write to known bad block on doubtful devices.
md/raid5: write errors should be recorded as bad blocks if possible.
md/raid5: use bad-block log to improve handling of uncorrectable read errors.
md/raid5: avoid reading from known bad blocks.
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
ALSA: hda - Fix duplicated DAC assignments for Realtek
ALSA: asihpi - off by one in asihpi_hpi_ioctl()
ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
ALSA: asihpi - bug fix pa use before init.
ALSA: hda - Add support for vref-out based mute LED control on IDT codecs
David S. Miller [Thu, 28 Jul 2011 06:33:03 +0000 (23:33 -0700)]
n2rng: Attach on Niagara-T3.
And stop referring to Victoria Falls, as the attribute we're
talking about is whether the rng is multi-unit capable which
applies to several chip variants now.
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Holzheu [Thu, 28 Jul 2011 07:06:46 +0000 (09:06 +0200)]
[S390] Export store_status() function
For kdump we need a store status function to save the registers for the
current CPU. Therefore this patch exports a function "store_status()".
In addition to that now also floating point registers are saved correctly.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Stefan Weinhuber [Thu, 28 Jul 2011 07:06:45 +0000 (09:06 +0200)]
[S390] dasd: use vmalloc for statistics input buffer
The size of the buffer that is used to store DASD statistics input
strings depends on the user input. If the input string is to large,
the write operation could fail with -ENOMEM. To avoid this, use
vmalloc instead of kmalloc.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Michael Holzheu [Thu, 28 Jul 2011 07:06:44 +0000 (09:06 +0200)]
[S390] Add PSW restart shutdown trigger
With this patch a new S390 shutdown trigger "restart" is added. If under
z/VM "systerm restart" is entered or under the HMC the "PSW restart" button
is pressed, the PSW located at 0 (31 bit) or 0x1a0 (64 bit) bit is loaded.
Now we execute do_restart() that processes the restart action that is
defined under /sys/firmware/shutdown_actions/on_restart. Currently the
following actions are possible: reipl (default), stop, vmcmd, dump, and
dump_reipl.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Jan Glauber [Thu, 28 Jul 2011 07:06:43 +0000 (09:06 +0200)]
[S390] missing return in page_table_alloc_pgste
Fix the following compile warning for !CONFIG_PGSTE:
CC arch/s390/mm/pgtable.o
arch/s390/mm/pgtable.c: In function ‘page_table_alloc_pgste’:
arch/s390/mm/pgtable.c:531:1: warning: no return statement in function returning non-void [-Wreturn-type]
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Jan Glauber [Thu, 28 Jul 2011 07:06:42 +0000 (09:06 +0200)]
[S390] qdio: 2nd stage retry on SIGA-W busy conditions
The SIGA-W may return with the busy bit set which means the device was
blocked. The busy loop which retries the SIGA-W for 100us may not be
long enough when running under a heavily loaded hypervisor.
Extend the retry mechanism by adding a longer second stage which retries
the SIGA-W for up to 10s. In difference to the first retry loop the second
stage is using mdelay to stop the cpu between the retries and thereby
avoid additional preassure in on the hypervisor.
If the second stage retry is successfull a device reset is avoided.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Matt Carlson [Wed, 27 Jul 2011 14:20:53 +0000 (14:20 +0000)]
tg3: Break larger frags into 4k chunks for 5719
The 5719 has bug where RDMAs larger than 4k can cause problems. This
patch works around the problem by dividing larger DMA requests into
something the hardware can handle.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:52 +0000 (14:20 +0000)]
tg3: Add tx BD budgeting code
As the driver breaks large skb fragments into smaller submissions to the
hardware, there is a new danger that BDs might get exhausted before all
fragments have been mapped. This patch adds code to make sure tx BDs
aren't oversubscribed and flag the condition if it happens.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:51 +0000 (14:20 +0000)]
tg3: Consolidate code that calls tg3_tx_set_bd()
This patch consolidates all code that populates tx BDs into a single
routine. Setting tx BDs needs to be more carefully controlled to see if
workarounds need to be applied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:50 +0000 (14:20 +0000)]
tg3: Add partial fragment unmapping code
The following patches are going to break skb fragments into smaller
sizes. This patch attempts to make the change easier to digest by only
addressing the skb teardown portion.
The patch modifies the driver to skip over any BDs that have a flag set
that indicates the BD isn't the beginning of an skb fragment. Such BDs
were a result of segmentation and do not need a pci_unmap_page() call.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:49 +0000 (14:20 +0000)]
tg3: Generalize tg3_skb_error_unmap()
In the following patches, unmapping skb fragments will get just as
complicated as mapping them. This patch generalizes
tg3_skb_error_unmap() and makes it the one-stop-shop for skb unmapping.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:48 +0000 (14:20 +0000)]
tg3: Remove short DMA check for 1st fragment
The first fragment of an skb should always be greater than 8 bytes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:47 +0000 (14:20 +0000)]
tg3: Simplify tx bd assignments
In the following patches, the process the driver will use to assign skb
fragments to transmit BDs will get more complicated. To prepare for
that new code, this patch seeks to simplify how transmit BDs are
populated. It does this by separating the code that assigns the BD
members from the logic that controls how the fields are set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:46 +0000 (14:20 +0000)]
tg3: Reintroduce tg3_tx_ring_info
The following patches will require the use of an additional flag in the
ring_info structure. The use of this flag is tx path specific, so this
patch defines a specialized ring_info structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Wed, 27 Jul 2011 10:09:26 +0000 (10:09 +0000)]
bonding: reduce noise during init
On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not? To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>
I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are. The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...
Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init
Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.
Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Tue, 26 Jul 2011 11:12:27 +0000 (11:12 +0000)]
bonding: fix string comparison errors
When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.
This was reported and based on work by Takuma Umeya. I also verified
the problem and tested that this fix resolves it.
V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.
I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.
V3: Actually sending the proper patch....
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Reported-by: Takuma Umeya <tumeya@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 26 Jul 2011 06:05:38 +0000 (06:05 +0000)]
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Karsten Keil <isdn@linux-pingi.de> CC: "David S. Miller" <davem@davemloft.net> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Patrick McHardy <kaber@trash.net> CC: Krzysztof Halasa <khc@pm.waw.pl> CC: "John W. Linville" <linville@tuxdriver.com> CC: Greg Kroah-Hartman <gregkh@suse.de> CC: Marcel Holtmann <marcel@holtmann.org> CC: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 26 Jul 2011 06:05:37 +0000 (06:05 +0000)]
net: add IFF_SKB_TX_SHARED flag to priv_flags
Pktgen attempts to transmit shared skbs to net devices, which can't be used by
some drivers as they keep state information in skbs. This patch adds a flag
marking drivers as being able to handle shared skbs in their tx path. Drivers
are defaulted to being unable to do so, but calling ether_setup enables this
flag, as 90% of the drivers calling ether_setup touch real hardware and can
handle shared skbs. A subsequent patch will audit drivers to ensure that the
flag is set properly
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Jiri Pirko <jpirko@redhat.com> CC: Robert Olsson <robert.olsson@its.uu.se> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Alexey Dobriyan <adobriyan@gmail.com> CC: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
commit 87c288c6e9aa31720b72e2bc2d665e24e1653c3e "gianfar: do vlan cleanup" has two issues:
# permutation of rx and tx flags
# enabling vlan tag insertion by default (this leads to unusable connections on some configurations)
If VLAN insertion is requested (via ethtool) it will be set at an other point ...
Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Jul 2011 04:06:16 +0000 (21:06 -0700)]
sparc: Detect and handle UltraSPARC-T3 cpu types.
The cpu compatible string we look for is "SPARC-T3".
As far as memset/memcpy optimizations go, we treat this chip the same
as Niagara-T2/T2+. Use cache initializing stores for memset, and use
perfetch, FPU block loads, cache initializing stores, and block stores
for copies.
We use the Niagara-T2 perf support, since T3 is a close relative in
this regard. Later we'll add support for the new events T3 can
report, plus enable T3's new "sample" mode.
For now I haven't added any new ELF hwcap flags. We probably need
to add a couple, for example:
T2 and T3 both support the population count instruction in hardware.
T3 supports VIS3 instructions, including support (finally) for
partitioned shift. One can also now move directly between float
and integer registers.
T3 supports instructions meant to help with Galois Field and other HPC
calculations, such as XOR multiply. Also there are "OP and negate"
instructions, for example "fnmul" which is multiply-and-negate.
T3 recognizes the transactional memory opcodes, however since
transactional memory isn't supported: 1) 'commit' behaves as a NOP and
2) 'chkpt' always branches 3) 'rdcps' returns all zeros and 4) 'wrcps'
behaves as a NOP.
So we'll need about 3 new elf capability flags in the end to represent
all of these things.
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (54 commits)
tpm_nsc: Fix bug when loading multiple TPM drivers
tpm: Move tpm_tis_reenable_interrupts out of CONFIG_PNP block
tpm: Fix compilation warning when CONFIG_PNP is not defined
TOMOYO: Update kernel-doc.
tpm: Fix a typo
tpm_tis: Probing function for Intel iTPM bug
tpm_tis: Fix the probing for interrupts
tpm_tis: Delay ACPI S3 suspend while the TPM is busy
tpm_tis: Re-enable interrupts upon (S3) resume
tpm: Fix display of data in pubek sysfs entry
tpm_tis: Add timeouts sysfs entry
tpm: Adjust interface timeouts if they are too small
tpm: Use interface timeouts returned from the TPM
tpm_tis: Introduce durations sysfs entry
tpm: Adjust the durations if they are too small
tpm: Use durations returned from TPM
TOMOYO: Enable conditional ACL.
TOMOYO: Allow using argv[]/envp[] of execve() as conditions.
TOMOYO: Allow using executable's realpath and symlink's target as conditions.
TOMOYO: Allow using owner/group etc. of file objects as conditions.
...
Fix up trivial conflict in security/tomoyo/realpath.c
md/raid10: Handle read errors during recovery better.
Currently when we get a read error during recovery, we simply abort
the recovery.
Instead, repeat the read in page-sized blocks.
On successful reads, write to the target.
On read errors, record a bad block on the destination,
and only if that fails do we abort the recovery.
As we now retry reads we need to know where we read from. This was in
bi_sector but that can be changed during a read attempt.
So store the correct from_addr and to_addr in the r10_bio for later
access.
md/raid10: simplify read error handling during recovery.
If a read error is detected during recovery the code currently
fails the read device.
This isn't really necessary. recovery_request_write will signal
a write error to end_sync_write and it will record a write
error on the destination device which will record a bad block
there or kick it from the array.
md/raid10: attempt to fix read errors during resync/check
We already attempt to fix read errors found during normal IO
and a 'repair' process.
It is best to try to repair them at any time they are found,
so move a test so that during sync and check a read error will
be corrected by over-writing with good data.
If both (all) devices have known bad blocks in the sync section we
won't try to fix even though the bad blocks might not overlap. That
should be considered later.
Also if we hit a read error during recovery we don't try to fix it.
It would only be possible to fix if there were at least three copies
of data, which is not very common with RAID10. But it should still
be considered later.
md/raid10 record bad blocks as needed during recovery.
When recovering one or more devices, if all the good devices have
bad blocks we should record a bad block on the device being rebuilt.
If this fails, we need to abort the recovery.
To ensure we don't think that we aborted later than we actually did,
we need to move the check for MD_RECOVERY_INTR earlier in md_do_sync,
in particular before mddev->curr_resync is updated.
md/raid10 - avoid reading from known bad blocks - part 3
When attempting to repair a read error, don't read from
devices with a known bad block.
As we are only reading PAGE_SIZE blocks, we don't try to
narrow down to smaller regions in the hope that only part of this
page is bad - it isn't worth the effort.
md/raid10: avoid reading from known bad blocks - part 1
This patch just covers the basic read path:
1/ read_balance needs to check for badblocks, and return not only
the chosen slot, but also how many good blocks are available
there.
2/ read submission must be ready to issue multiple reads to
different devices as different bad blocks on different devices
could mean that a single large read cannot be served by any one
device, but can still be served by the array.
This requires keeping count of the number of outstanding requests
per bio. This count is stored in 'bi_phys_segments'
On read error we currently just fail the request if another target
cannot handle the whole request. Next patch refines that a bit.
When a loop ends with a large if, it can be neater to change the
if to invert the condition and just 'continue'.
Then the body of the if can be indented to a lower level.
projects / karo-tx-linux.git / log