Set the max packet size for the default control endpoint on high speed
devices to be 64 bytes. High speed devices always have a max packet size
of 64 bytes. There's no use setting it to eight for the initial 8 byte
descriptor fetch and then issuing (and waiting for) an evaluate context
command to update it to 64 bytes for the subsequent control transfers.
The USB core guesses that the max packet size on a full speed control
endpoint is 64 bytes, and then updates it after the first 8-byte
descriptor fetch. Change the initial setup for the xHCI internal
representation of the full speed device to have a 64 byte max packet size.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor out the code issue, wait for, and parse the event completion code
for a configure endpoint command. Modify it to support the evaluate
context command, which has a very similar submission process. Add
functions to copy parts of the output context into the input context
(which will be used in the evaluate context command).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Different sections of the xHCI 0.95 specification had opposing
requirements for the chain bit in a link transaction request buffer (TRB).
The chain bit is used to designate that adjacent TRBs are all part of the
same scatter gather list that should be sent to the device. Link TRBs can
be in the middle, or at the beginning or end of these chained TRBs.
Sections 4.11.5.1 and 6.4.4.1 both stated the link TRB "shall have the
chain bit set to 1", meaning it is always chained to the next TRB.
However, section 4.6.9 on the stop endpoint command has specific cases for
what the hardware must do for a link TRB with the chain bit set to 0. The
0.96 specification errata later cleared up this issue by fixing the
4.11.5.1 and 6.4.4.1 sections to state that a link TRB can have the chain
bit set to 1 or 0.
The problem is that the xHCI cancellation code depends on the chain bit of
the link TRB being cleared when it's at the end of a TD, and some 0.95
xHCI hardware simply stops processing the ring when it encounters a link
TRB with the chain bit cleared.
Allow users who are testing 0.95 xHCI prototypes to set a module parameter
(link_quirk) to turn on this link TRB work around. Cancellation may not
work if the ring is stopped exactly on a link TRB with chain bit set, but
cancellation should be a relatively uncommon case.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1292) modifies the USB serial console driver, to make it
compatible with the recent changes to the USB serial core. The most
important change is that serial->disc_mutex now has to be unlocked
following a successful call to usb_serial_get_by_index().
Other less notable changes include:
Use the requested port number instead of port 0 always.
Prevent the serial device from being autosuspended.
Use the ASYNCB_INITIALIZED flag bit to indicate when the
port hardware has been initialized.
In spite of these changes, there's no question that the USB serial
console code is still a big hack.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1291) removes a bunch of code from serial_open(), things
that were rendered unnecessary by earlier patches. A missing spinlock
is added to protect port->port.count, which needs to be incremented
even if the open fails but not if the tty has gotten a hangup. The
test for whether the hardware has been initialized, based on the use
count, is replaced by a more transparent test of the
ASYNCB_INITIALIZED bit in the port flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1290) adds some missing tests. serial_down() isn't
supposed to do anything if the hardware hasn't been initialized, and
serial_close() isn't supposed to do anything if the tty has gotten a
hangup (because serial_hangup() takes care of shutting down the
hardware).
The patch also updates and adds a few debugging lines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1289) renames serial_do_down() to serial_down() and
serial_do_free() to serial_release(). It also adds a missing call to
tty_shutdown() in serial_release().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1288) fixes the initialization logic in
serial_install(). A new tty always needs to have a termios
initialized no matter what, not just in the case where the lower
driver will override the termios settings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1287) makes serial_install() be reponsible for acquiring
references to the usb_serial structure and the driver module when a
tty is first used. This is more sensible than having serial_open() do
it, because a tty can be opened many times whereas it is installed
only once, when it is created. (Not to mention that these actions are
reversed when the tty is released, not when it is closed.) Finally,
it is at install time that the TTY core takes its own reference to the
usb_serial module, so it is only fitting that we should act the same
way in regard to the lower-level serial driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1286) changes usb_serial_get_by_index(). Now the
routine will check whether the serial device has been disconnected; if
it has then the return value will be NULL. If the device hasn't been
disconnected then the routine will return with serial->disc_mutex
held, so that the caller can use the structure without fear of racing
against driver unloads.
This permits the scope of table_mutex in destroy_serial() to be
reduced. Instead of protecting the entire function, it suffices to
protect the part that actually uses serial_table[], i.e., the call to
return_serial(). There's no longer any danger of the refcount being
incremented after it reaches 0 (which was the reason for having the
large scope previously), because it can't reach 0 until the serial
device has been disconnected.
Also, the patch makes serial_install() check that serial is non-NULL
before attempting to use it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1285) rearranges the subroutines in usb-serial.c
concerned with tty lifetimes into a more logical order: install, open,
hangup, close, release. It also updates the formatting of the
kerneldoc comments.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1284) changes the referencing of the usb_serial and
usb_serial_port structures in usb-serial.c. It's not feasible to make
the port structures keep a reference to the serial structure, because
the ports need to remain in existence when serial is released -- quite
a few of the drivers expect this. Consequently taking a reference
to the port when the device file is open is insufficient; such a
reference would not pin serial.
To fix this, we now take a reference to serial when the device file is
opened. The final put_device() for the ports occurs in
destroy_serial(), so that the ports will last as long as they are
needed.
The patch initializes all the port devices, including those in the
unused "fake" ports. This makes the code more uniform because they
can all be released in the same way. The error handling code in
usb_serial_probe() is much simplified by this approach; instead of
freeing everything by hand we can use a single usb_serial_put() call.
Also simplified is the port-release mechanism. Instead of being two
separate routines, port_release() and port_free() can be combined into
one.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various drivers have hacks to mangle termios structures. This stems from
the fact there is no nice setup hook for configuring the termios settings
when the port is created
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB layer uses tty_hangup to deal with unplugs of the physical hardware
(analogous to loss of carrier) and then frees the resources. However the
tty_hangup is asynchronous. As the hangup can sleep we can use tty_vhangup
which is the non async version to avoid freeing resources too early.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now we are extracting out methods for shutdown and the like we can add a
proper tty_port_close method that knows all the innards of the tty closing
process and hides the lot from the caller.
At some point in the future this will be paired with a similar open()
helper and the drivers can stick to hardware management.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1271) affects when new devices get linked into their
bus's list of devices. Currently this happens after probing, and it
doesn't happen at all if probing fails. Clearly this is wrong,
because at that point quite a few symbolic links have already been
created in sysfs. We are committed to adding the device, so it should
be linked into the bus's list regardless.
In addition, this needs to happen before the uevent announcing the new
device gets issued. Otherwise user programs might try to access the
device before it has been added to the bus.
To fix both these problems, the patch moves the call to
klist_add_tail() forward from bus_attach_device() to bus_add_device().
Since bus_attach_device() now does nothing but probe for drivers, it
has been renamed to bus_probe_device(). And lastly, the kerneldoc is
updated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Paraphrasing Rafael J. Wysocki: "drivers should not release PCI IRQs
in suspend." Doing so causes a warning during suspend/resume on some
platforms.
Cc: Rafael J. Wysocki <rjw@sisk.pl> Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Don't put chip to full sleep because there are problems during
wakeup. Instead hold MAC/Baseband on warm reset state via a new
function ath5k_hw_on_hold.
* Minor cleanups
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Tested-by: Ben Greear <greearb@candelatech.com> Tested-by: Johannes Stezenbach <js@sig21.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 19eda87 (netfilter: change return types of check functions for
Ebtables extensions) broke the ebtables ulog module by missing a return
value conversion.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kernel 2.6.30 introduced a patch [1] for the persistent option in the
netfilter SNAT target. This is exactly what we need here so I had a quick look
at the code and noticed that the patch is wrong. The logic is simply inverted.
The patch below fixes this.
Also note that because of this the default behavior of the SNAT target has
changed since kernel 2.6.30 as it now ignores the destination IP in choosing
the source IP for nating (which should only be the case if the persistent
option is set).
This improves patch fa6963b24 so that perf.data stuff that has
been dumped as root can be read (annotate/report) by a user
without the use of the --force.
Rationale is that root has plenty of ways to screw us (usually)
that do not require twisted schemes involving specially
crafting a perf.data.
Signed-off-by: Pierre Habouzit <pierre.habouzit@intersec.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090827075902.GF19653@laphroaig.corp> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To my understanding, it became obsolete with the advent of the more
robust check in mmu_alloc_roots (89da4ff17f). Moreover, it prevents
the conceptually safe pattern
1. set sregs
2. register mem-slots
3. run vcpu
by setting a sticky triple fault during step 1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
n_requested_mmu_pages/n_free_mmu_pages are used by
kvm_mmu_change_mmu_pages to calculate the number of pages to zap.
alloc_mmu_pages, called from the vcpu initialization path, modifies this
variables without proper locking, which can result in a negative value
in kvm_mmu_change_mmu_pages (say, with cpu hotplug).
Commit ac89a9174 ("pty: don't limit the writes to 'pty_space()' inside
'pty_write()'") removed the pty_space() checking, in order to let the
regular tty buffer code limit the buffering itself.
That was all good, but as a subtle side effect it meant that we'd be
doing a tty_wakeup() even in the case where the buffers were all filled
up, and didn't actually make any progress on the write.
Which sounds innocuous, but it interacts very badly with the ppp_async
code, which has an infinite loop in ppp_async_push() that tries to push
out data to the tty. When we call tty_wakeup(), that loop ends up
thinking that progress was made (see the subtle interactions between
XMIT_WAKEUP and 'tty_stuffed' for details). End result: one unhappy ppp
user.
Fixed by noticing when tty_insert_flip_string() didn't actually do
anything, and then not doing any more processing (including, very much
not calling tty_wakeup()).
The length of the to-copy data structure is currently stored in
a signed integer. However many comparisons are done with sizeof(..)
which is unsigned. It's more suitable for this variable to be unsigned
to make these comparisons more naturally right.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
as a security check against optlen being negative (or zero) in the
set socket option.
Unfortunately, "sizeof(int)" is an unsigned property, with the
result that the whole comparison is done in unsigned, letting
negative values slip through.
This patch changes this to
if (optlen < (int)sizeof(int))
return -EINVAL;
so that the comparison is done as signed, and negative values
get properly caught.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sharpsl_pm.c code tries to read battery state very early during
resume, but those battery meters are connected on SPI and that's only
resumed way later.
Replace the check with simple checking of battery fatal signal, that
actually works at this stage.
Signed-off-by: Pavel Machek <pavel@ucw.cz> Tested-by: Stanislav Brabec <utx@penguin.cz> Signed-off-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a5bfc4714b3f01365aef89a92673f2ceb1ccf246 dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions. There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.
http://bugzilla.kernel.org/show_bug.cgi?id=14124
I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using nanosleep() in an userspace application we get a ratelimit warning
NOHZ: local_softirq_pending 08
for 10 times.
The echo of CAN frames is done from process context and softirq context only.
Therefore the usage of netif_rx() was wrong (for years).
This patch replaces netif_rx() with netif_rx_ni() which has to be used from
process/softirq context. It also adds a missing comment that can_send() must
no be used from hardirq context.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: Urs Thuermann <urs@isnogud.escape.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On setting up the callback to the client, we attempt to use the same
authentication flavor the client did. We find an rpc cred to use by
calling rpcauth_lookup_credcache(), which assumes that the given
authentication flavor has a credentials cache. However, this is not
required to be true--in particular, auth_null does not use one.
Instead, we should call the auth's lookup_cred() method.
Without this, a client attempting to mount using nfsv4 and auth_null
triggers a null dereference.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ever since we enabled GEM, the pre-9xx chipsets (particularly 865) have had
serious stability issues. Back in May a wbinvd was added to the DRM to
work around much of the problem. Some failure remained -- easily visible
by dragging a window around on an X -retro desktop, or by looking at bugzilla.
The chipset flush was on the right track -- hitting the right amount of
memory, and it appears to be the only way to flush on these chipsets, but the
flush page was mapped uncached. As a result, the writes trying to clear the
writeback cache ended up bypassing the cache, and not flushing anything! The
wbinvd would flush out other writeback data and often cause the data we wanted
to get flushed, but not always. By removing the setting of the page to UC
and instead just clflushing the data we write to try to flush it, we get the
desired behavior with no wbinvd.
This exports clflush_cache_range(), which was laying around and happened to
basically match the code I was otherwise going to copy from the DRM.
mac Mini's have a single DDC line on the DVI connector, shared between the
analog link and the digital link. So, if DDC isn't detected on GPIOE (the
usual SDVO DDC link), try GPIOA (the usual VGA DDC link) when there isn't a
VGA monitor connected.
Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arrandale has new window based method for panel fitting.
This one enables full screen aspect scaling on LVDS. It fixes
standard mode display failure on LVDS for Arrandale.
Eric noted a potential concern with the low bits not being strictly used
as part of the absolute offset (instead part of the command stream to the
GPU), but in practice that should not be an issue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Andy Whitcroft <apw@canonical.com> Cc: Eric Anholt <eric@anholt.net> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A very high dotclock (e.g. 229500kHz as reported by Anton) can cause
the entries_required variable to overflow, potentially leading to a
FIFO watermark value that's too low to support the given mode. Split
the division across the calculation to avoid this.
Reported-by: Anton Khirnov <wyskas@gmail.com> Tested-by: Anton Khirnov <wyskas@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drm_ht_remove_item() does not handle removing an absent item and the hlist
in particular is incorrectly initialised. The easy remedy is simply skip
calling i915_gem_free_mmap_offset() unless we have actually created the
offset and associated ht entry.
This also fixes the mishandling of a partially constructed offset which
leaves pointers initialized after freeing them along the
i915_gem_create_mmap_offset() error paths.
In particular this should fix the oops found here:
https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/415357/comments/8
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Eric Anholt <eric@anholt.net>
SL811 Device detected after removal used to be working in linux-2.6.22
but then broke somewhere between 2.6.22 and 2.6.28. Current
hub_port_connect_change() in drivers/usb/core/hub.c won't call
usb_disconnect() in case the SL811 driver sets portstatus
USB_PORT_FEAT_CONNECTION upon removal.
AFAIK the SL811 has only a combined Device Insert/Remove
detection bit, therefore use a count to distinguish insert or remove.
Signed-Off-By: Michael Hennerich <hennerich@blackfin.uclinux.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the specifications, an instrument should not return more data in a
DEV_DEP_MSG_IN urb than requested. However, some instruments can send more
than requested. This could cause the kernel to write the extra data past the
end of the buffer provided by read().
Fix this by checking that the value of the TranserSize field is not larger than
the urb itself and not larger than the size of the userspace buffer. Also
correctly decrement the remaining size of the buffer when userspace read()s
more than USBTMC_SIZE_IOBUFFER.
In this patch, we always make the return value of function
usb_stor_huawei_e220_init to be zero. Then it will not prevent usb-storage
driver from attaching to the CDROM device of Huawei Datacard.
The UV BIOS has changed the way interrupt remapping is being done.
This affects the id used for sending IPIs. The upper id bits no
longer need to be masked off.
kaweth_control() never frees the buffer that it allocates for the USB
control message. Test case:
while :; do ifconfig eth2 down ; ifconfig eth2 up ; done
This is a tiny buffer so it is a slow leak. If you want to speed up the
process, you can change the allocation size to e.g. 16384 bytes, and it
will consume several megabytes within a few minutes.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty_operation chars_in_buffer() is not allowed to return a negative
value to signal an error. Corrects the problem flagged by commit 23198fda7182969b619613a555f8645fdc3dc334, "tty: fix chars_in_buffers".
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices from the OpenDCC project are missing in the list
of the FTDI PIDs. These PIDs are listed at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
(Sorry for the german only page.)
This patch adds the three missing devices.
The M29W128G Numonyx flash devices are intolerant to any 0xFF command:
in the Cfi_util.c the function cfi_qry_mode_off() (that resets the device
after the autoselect mode) must have a 0xF0 command after the 0xFF command.
This fix solves also the cause of the fixup_M29W128G_write_buffer() fix,
that can be removed now.
The following patch applies to 2.6.30 kernel.
The previous implementation breaks the dts binding "mtd-physmap.txt". This
implementation fixes the issue by checking the availability of the reg
property instead of the name property.
Signed-off-by: Benjamin Krill <ben@codiert.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix ECC Correction bug where the byte offset location were double
fliped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
/* The NDFC uses Smart Media (SMC) bytes order */
ecc_code[0] = p[2];
ecc_code[1] = p[1];
ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the b1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
byte_addr = (addressbits[b1] << 4) + addressbits[b0];
The order is change to read it in straight and let the correction
function to revert it to SMC order.
Signed-off-by: Feng Kan <fkan@amcc.com> Acked-by: Victor Gallardo <vgallardo@amcc.com> Acked-by: Prodyut Hazarika <phazarika@amcc.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will fix file system corruption which infrequently happens after
mount. The problem was reported from users with the title "[NILFS
users] Fail to mount NILFS." (Message-ID:
<200908211918.34720.yuri@itinteg.net>), and so forth. I've also
experienced the corruption multiple times on kernel 2.6.30 and 2.6.31.
The problem turned out to be caused due to discordance between
mapping->nrpages of a btree node cache and the actual number of pages
hung on the cache; if the mapping->nrpages becomes zero even as it has
pages, truncate_inode_pages() returns without doing anything. Usually
this is harmless except it may cause page leak, but garbage collection
fairly infrequently sees a stale page remained in the btree node cache
of DAT (i.e. disk address translation file of nilfs), and induces the
corruption.
I identified a missing initialization in btree node caches was the
root cause. This corrects the bug.
"I recently (on a flight) I found out that when I boot with the hard-switch
activated, so turning off all wireless activity on my laptop, the state
is not correctly announced in /dev/rfkill (reading it with rfkill command,
or my own gnome applet)...
After turning off and on again the hard-switch the events were right."
We can fix this by querying the firmware at load time and calling
rfkill_set_hw_state().
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Tested-by: Norbert Preining <preining@logic.at> Acked-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Mattia Dongili <malattia@linux.it> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since 2.6.29 the PCI PM core have been restoring the standard
configuration registers of PCI devices in the early phase of
resume. In particular, PCI devices without drivers have been handled
this way since commit 355a72d75b3b4f4877db4c9070c798238028ecb5
(PCI: Rework default handling of suspend and resume). Unfortunately,
this leads to post-resume problems with CardBus devices which cannot
be accessed in the early phase of resume, because the sockets they
are on have not been woken up yet at that point.
To solve this problem, move the yenta socket resume to the early
phase of resume and, analogously, move the suspend of it to the late
phase of suspend. Additionally, remove some unnecessary PCI code
from the yenta socket's resume routine.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13092, which is a
post-2.6.28 regression.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-by: Florian <fs-kernelbugzilla@spline.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x86-64 assumes NX is available by default, so we need to
explicitly check for it before using NX. Some first-generation
Intel x86-64 processors didn't support NX, and even recent systems
allow it to be disabled in BIOS.
[ Impact: prevent Xen crash on NX-less 64-bit machines ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to have a stronger barrier between releasing the lock and
checking for any waiting spinners. A compiler barrier is not sufficient
because the CPU's ordering rules do not prevent the read xl->spinners
from happening before the unlock assignment, as they are different
memory locations.
We need to have an explicit barrier to enforce the write-read ordering
to different memory locations.
Because of it, I can't bring up > 4 HVM guests on one SMP machine.
[ Code and commit comments expanded -J ]
[ Impact: avoid deadlock when using Xen PV spinlocks ]
Signed-off-by: Yang Xiaowei <xiaowei.yang@intel.com> Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Where possible we enable interrupts while waiting for a spinlock to
become free, in order to reduce big latency spikes in interrupt handling.
However, at present if we manage to pick up the spinlock just before
blocking, we'll end up holding the lock with interrupts enabled for a
while. This will cause a deadlock if we recieve an interrupt in that
window, and the interrupt handler tries to take the lock too.
Solve this by shrinking the interrupt-enabled region to just around the
blocking call.
[ Impact: avoid race/deadlock when using Xen PV spinlocks ]
-fstack-protector uses a special per-cpu "stack canary" value.
gcc generates special code in each function to test the canary to make
sure that the function's stack hasn't been overrun.
On x86-64, this is simply an offset of %gs, which is the usual per-cpu
base segment register, so setting it up simply requires loading %gs's
base as normal.
On i386, the stack protector segment is %gs (rather than the usual kernel
percpu %fs segment register). This requires setting up the full kernel
GDT and then loading %gs accordingly. We also need to make sure %gs is
initialized when bringing up secondary cpus too.
To keep things consistent, we do the full GDT/segment register setup on
both architectures.
Because we need to avoid -fstack-protected code before setting up the GDT
and because there's no way to disable it on a per-function basis, several
files need to have stack-protector inhibited.
[ Impact: allow Xen booting with stack-protector enabled ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ac68392460ffefed13020967bae04edc4d3add06 ("[CIFS] Allow raw
ntlmssp code to be enabled with sec=ntlmssp") added a new bit to the
allowed security flags mask but seems to have inadvertently removed
Lanman security from the allowed flags. Add it back.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When calling vfs_unlink() on the lower dentry, d_delete() turns the
dentry into a negative dentry when the d_count is 1. This eventually
caused a NULL pointer deref when a read() or write() was done and the
negative dentry's d_inode was dereferenced in
ecryptfs_read_update_atime() or ecryptfs_getxattr().
Placing mutt's tmpdir in an eCryptfs mount is what initially triggered
the oops and I was able to reproduce it with the following sequence:
When searching through the global authentication tokens for a given key
signature, verify that a matching key has not been revoked and has not
expired. This allows the `keyctl revoke` command to be properly used on
keys in use by eCryptfs.
Returns -ENOTSUPP when attempting to use filename encryption with
something other than a password authentication token, such as a private
token from openssl. Using filename encryption with a userspace eCryptfs
key module is a future goal. Until then, this patch handles the
situation a little better than simply using a BUG_ON().
If the lower inode is read-only, don't attempt to open the lower file
read/write and don't hand off the open request to the privileged
eCryptfs kthread for opening it read/write. Instead, only try an
unprivileged, read-only open of the file and give up if that fails.
This patch fixes an oops when eCryptfs is mounted on top of a read-only
mount.
Returns an error when an unrecognized cipher code is present in a tag 3
packet or an ecryptfs_crypt_stat cannot be initialized. Also sets an
crypt_stat->tfm error pointer to NULL to ensure that it will not be
incorrectly freed in ecryptfs_destroy_crypt_stat().
In theory it could happen that on one CPU we initialize a new inode but
clearing of I_NEW | I_LOCK gets reordered before some of the
initialization. Thus on another CPU we return not fully uptodate inode
from iget_locked().
This seems to fix a corruption issue on ext3 mounted over NFS.
[akpm@linux-foundation.org: add some commentary] Signed-off-by: Jan Kara <jack@suse.cz> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some time ago, I have send a patch to the mmc_spi subsystem changing the
error codes. This was after a discussion with Pierre about using EINVAL
only for non-recoverable errors. This patch was accepted as
Unfortunately, several weeks later, I realized that this patch has opened
a little can of worms because there are SD cards on the market which
a) claim that they support the switch command
AND
b) refuse to execute this command if operating in SPI mode.
So, such a card would get unusuable in an embedded linux system in SPI
mode, because the init sequence terminates with an error.
This patch adds the missing error codes to the caller of the switch
command and restores the old behaviour to fail gracefully if these
commands can not execute.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b478b782e110fdb4135caa3062b6d687e989d994 "kallsyms, tracing: output
more proper symbol name" introduces a "bugfix" that introduces a segfault
in kallsyms in my configurations.
The cause is the introduction of prefix_underscores_count() which attempts
to count underscores, even in symbols that do not have them. As a result,
it just uselessly runs past the end of the buffer until it crashes:
Attempting to unload a framebuffer module calls unregister_framebuffer()
which in turn gets fbcon to release it. If fbcon has no framebuffers
linked to a console, it will also unbind itself from the console driver.
However, if fbcon never registered itself as a console driver, the unbind
will fail causing the framebuffer device entry to persist. In most cases
this failure will result in an oops when attempting to access the now
non-existent device.
This patch ensures that the fbcon unbind request will succeed even if a
bind was never done. It tracks if a successful bind ever occurred & will
only attempt to unbind if needed. If there never was a bind, it simply
returns with no error.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Similar to commit b6adc195 (PCI hotplug: acpiphp wants a 64-bit
_SUN), pci_slot.ko reads and creates sysfs directories based on
the _SUN method.
Certain HP platforms return 64 bits in _SUN. This change to
pci_slot.ko allows us to see the correct sysfs directories.
Reported-by: Chad Smith <chad.smith@hp.com> Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
X40 (firmware 1V) and T41 (firmware 1R) have been confirmed to work
well with the new defaults, so we can stop pestering people to confirm
that fact.
For now, whitelist just these two firmware types. It is best to have
at least one more firmware type confirmed for Radeon 9xxx and Intel
GMA-2 ThinkPads before removing the confirmation requests entirely.
Reported-by: Robert de Rooy <robert.de.rooy@gmail.com> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The arch/*/boot/Makefile use cc-options to check for GCC command options
and cc-options use the hardened specs when checking for GCC command
options. When -fPIE is pass to cc1 it can't use -ffreestanding or
-fno-toplevel-reorder. Then it fail to build stuff with -ffreestanding
and -fno-toplevel-reorder.
Thanks to Fredric Johansson for finding the main problem behind a failed
build using a hardened toolchain.
Signed-off-by: Magnus Granberg <zorry@ume.nu> Signed-off-by: Jory A. Pratt <anarchy@gentoo.org> Cc: Fredric Johansson <johansson_fredric@hotmail.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log