As explained in commit 1c0fe6e3bd, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.
Cc: linuxppc-dev@ozlabs.org Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linux-arch@vger.kernel.org Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mark Nelson [Wed, 21 Apr 2010 16:21:03 +0000 (16:21 +0000)]
powerpc/mm: Track backing pages allocated by vmemmap_populate()
We need to keep track of the backing pages that get allocated by
vmemmap_populate() so that when we use kdump, the dump-capture kernel knows
where these pages are.
We use a simple linked list of structures that contain the physical address
of the backing page and corresponding virtual address to track the backing
pages.
To save space, we just use a pointer to the next struct vmemmap_backing. We
can also do this because we never remove nodes. We call the pointer "list"
to be compatible with changes made to the crash utility.
vmemmap_populate() is called either at boot-time or on a memory hotplug
operation. We don't have to worry about the boot-time calls because they
will be inherently single-threaded, and for a memory hotplug operation
vmemmap_populate() is called through:
sparse_add_one_section()
|
V
kmalloc_section_memmap()
|
V
sparse_mem_map_populate()
|
V
vmemmap_populate()
and in sparse_add_one_section() we're protected by pgdat_resize_lock().
So, we don't need a spinlock to protect the vmemmap_list.
We allocate space for the vmemmap_backing structs by allocating whole pages
in vmemmap_list_alloc() and then handing out chunks of this to
vmemmap_list_populate().
This means that we waste at most just under one page, but this keeps the code
is simple.
Signed-off-by: Mark Nelson <markn@au1.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wolfram Sang [Thu, 1 Apr 2010 14:17:01 +0000 (14:17 +0000)]
i2c/ibm-iic: Drop NO_IRQ
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Sean MacLennan <smaclennan@pikatech.com> Cc: Ben Dooks <ben-linux@fluff.org> Acked-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wolfram Sang [Thu, 1 Apr 2010 14:17:00 +0000 (14:17 +0000)]
i2c/cpm: Drop NO_IRQ
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Jochen Friedrich <jochen@scram.de> Cc: Ben Dooks <ben-linux@fluff.org> Acked-by: Jochen Friedrich <jochen@scram.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wolfram Sang [Thu, 1 Apr 2010 14:16:59 +0000 (14:16 +0000)]
i2c/mpc: Drop NO_IRQ
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the parsing of the device tree in
arch/powerpc/include/asm/parport.h assumes that the interrupt provided in
the parallel port node is a valid virtual irq. The values for the
interrupts provided in the device tree should have meaning in the context
of the driver for the specific interrupt controller to which the interrupt
is connected and irq_of_parse_and_map() should be used to determine the
correct virtual irq.
Signed-off-by: Martyn Welch <martyn.welch@ge.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So we tried to speed things up a bit using flush_hash_pages() directly
but that falls over on 603 of course meaning we fail to flush the TLB
properly and we may even end up having it corrupt memory randomly by
accessing a hash table that doesn't exist.
This removes the "optimization" by always going through flush_tlb_page()
for now at least.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 28 Apr 2010 13:39:41 +0000 (13:39 +0000)]
powerpc/pseries: Only call start-cpu when a CPU is stopped
Currently we always call start-cpu irrespective of if the CPU is
stopped or not. Unfortunatley on POWER7, firmware seems to not like
start-cpu being called when a cpu already been started. This was not
the case on POWER6 and earlier.
This patch checks to see if the CPU is stopped or not via an
query-cpu-stopped-state call, and only calls start-cpu on CPUs which
are stopped.
This fixes a bug with kexec on POWER7 on PHYP where only the primary
thread would make it to the second kernel.
Reported-by: Ankita Garg <ankita@linux.vnet.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stefan Roese [Tue, 27 Apr 2010 22:13:34 +0000 (22:13 +0000)]
powerpc/4xx: Add optional "reset_type" property to control reboot via dts
By setting "reset_type" to one of the following values, the default
software reset mechanism may be overidden. Here the possible values of
"reset_type":
Torez Smith [Fri, 5 Mar 2010 10:45:54 +0000 (10:45 +0000)]
powerpc/4xx: Simple platform for the ISS 4xx simulator
This is a trivial 4xx plaform that uses the new simple bsp from
Josh and is handy to use in simulators such as ISS or even Mambo
who don't properly implement most of the actual devices in the
SoC but really only the core.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Dave Kleikamp [Fri, 5 Mar 2010 10:43:24 +0000 (10:43 +0000)]
powerpc/476: Add isync after loading mmu and debug spr's
476 requires an isync after loading MMU and debug related SPR's. Some of
these are in performance-critical paths and may need to be optimized, but
initially, we're playing it safe.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Dave Kleikamp [Fri, 5 Mar 2010 10:43:12 +0000 (10:43 +0000)]
powerpc/47x: Base ppc476 support
This patch adds the base support for the 476 processor. The code was
primarily written by Ben Herrenschmidt and Torez Smith, but I've been
maintaining it for a while.
The goal is to have a single binary that will run on 44x and 47x, but
we still have some details to work out. The biggest is that the L1 cache
line size differs on the two platforms, but it's currently a compile-time
option.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Dave Kleikamp [Fri, 5 Mar 2010 10:43:07 +0000 (10:43 +0000)]
powerpc/44x: break out cpu init code into stand-alone function
The 47x platform supports multiple cores and shares code with 44x.
Break out code that is common for initializing the primary and secondary
cpus into a function which can be called for both.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Torez Smith [Fri, 5 Mar 2010 10:43:01 +0000 (10:43 +0000)]
powerpc/booke: Add Stack Marking support to Booke Exception Prolog
This patch adds a marker to the exception stack frame to aid in debugging.
It's already inserted on other platforms and xmon recognizes it and
identifies exception frames when showing stack traces.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Akinobu Mita [Sun, 28 Feb 2010 00:58:16 +0000 (00:58 +0000)]
powerpc/iseries/pci: Use __ratelimit
Replace open-coded rate limiting logic with __ratelimit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: linuxppc-dev@ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
And it has proven to be an issue during boot on very large machines.
If hotplug memory is enabled, drivers/base/memory.c does this:
for (i = 0; i < NR_MEM_SECTIONS; i++) {
if (!present_section_nr(i))
continue;
err = add_memory_block(0, __nr_to_section(i), MEM_ONLINE,
0, BOOT);
if (!ret)
ret = err;
}
Which creates a sysfs directory for every 16MB of memory. As a result
I'm seeing up to 30 minutes spent here during boot:
I assume there are some O(n^2) issues in sysfs as we add all the memory
nodes. Bumping SECTION_SIZE_BITS to 256 MB drops the time to about 10
seconds and results in a much smaller /sys.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Thu, 18 Feb 2010 12:11:51 +0000 (12:11 +0000)]
powerpc/pseries: Call ibm,os-term if the ibm,extended-os-term is present
We have had issues in the past with ibm,os-term initiating shutdown of a
partition. This is confusing to the user, especially if panic_timeout is
non zero.
The temporary fix was to avoid calling ibm,os-term if a panic_timeout was set
and since we set it on every boot we basically never call ibm,os-term.
An extended version of ibm,os-term has since been implemented which gives us
the behaviour we want:
"When the platform supports extended ibm,os-term behavior, the return to the
RTAS will always occur unless there is a kernel assisted dump active as
initiated by an ibm,configure-kernel-dump call."
This patch checks for the ibm,extended-os-term property and calls ibm,os-term
if it exists.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Thu, 18 Feb 2010 12:29:23 +0000 (12:29 +0000)]
powerpc/numa: Set a smaller value for RECLAIM_DISTANCE to enable zone reclaim
I noticed /proc/sys/vm/zone_reclaim_mode was 0 on a ppc64 NUMA box. It gets
enabled via this:
/*
* If another node is sufficiently far away then it is better
* to reclaim pages in a zone before going off node.
*/
if (distance > RECLAIM_DISTANCE)
zone_reclaim_mode = 1;
Since we use the default value of 20 for REMOTE_DISTANCE and 20 for
RECLAIM_DISTANCE it never kicks in.
The local to remote bandwidth ratios can be quite large on System p
machines so it makes sense for us to reclaim clean pagecache locally before
going off node.
The patch below sets a smaller value for RECLAIM_DISTANCE and thus enables
zone reclaim.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wolfram Sang [Sat, 20 Mar 2010 04:12:50 +0000 (04:12 +0000)]
powerpc/pmac: Fix dangling pointers
Fix I2C-drivers which missed setting clientdata to NULL before freeing the
structure it points to. Also fix drivers which do this _after_ the structure
was freed already.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Colin Leroy <colin@colino.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
f (...) { <+...
* spin_lock_irq (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Julia Lawall [Fri, 2 Apr 2010 02:47:13 +0000 (02:47 +0000)]
powerpc/pseries/dlpar: Eliminate use after free
dlpar_free_cc_nodes frees its argument, so dlpar_online_cpu should not be
called on the same value. Skip over the call to dlpar_online_cpu by
jumping directly to out.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
dlpar_free_cc_nodes(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jeff Mahoney [Wed, 17 Mar 2010 10:55:51 +0000 (10:55 +0000)]
powerpc: Fix handling of strncmp with zero len
Commit 0119536c, which added the assembly version of strncmp to
powerpc, mentions that it adds two instructions to the version from
boot/string.S to allow it to handle len=0. Unfortunately, it doesn't
always return 0 when that is the case. The length is passed in r5, but
the return value is passed back in r3. In certain cases, this will
happen to work. Otherwise it will pass back the address of the first
string as the return value.
This patch lifts the len <= 0 handling code from memcpy to handle that
case.
Reported by: Christian_Sellars@symantec.com Signed-off-by: Jeff Mahoney <jeffm@suse.com> CC: <stable@kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
d binderman [Thu, 18 Mar 2010 23:01:42 +0000 (23:01 +0000)]
powerpc/pmac/windfarm: Don't test pointers before kfree()
Fix minor nits found by cppcheck
[./macintosh/windfarm_pm81.c:760]: (style) Redundant condition. It is safe to deallocate a NULL pointer
[./macintosh/windfarm_pm81.c:762]: (style) Redundant condition. It is safe to deallocate a NULL pointer
Signed-off-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
d binderman [Sat, 6 Feb 2010 02:13:29 +0000 (02:13 +0000)]
powerpc/pmac/low_i2c.c: three minor problems
Fix minor nits found by cppcheck
[./arch/powerpc/platforms/powermac/low_i2c.c:594]: (style) The scope of the variable chans can be reduced
[./arch/powerpc/platforms/powermac/low_i2c.c:594]: (style) The scope of the variable i can be reduced
[./arch/powerpc/platforms/powermac/low_i2c.c:1260]: (style) Redundant condition. It is safe to deallocate a NULL pointer
Signed-off-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jason Gunthorpe [Tue, 9 Mar 2010 09:35:00 +0000 (09:35 +0000)]
powerpc/ppc32: Fixup pmd_page to work when ARCH_PFN_OFFSET is non-zero
Instead of referencing mem_map directly, use pfn_to_page. Otherwise
the kernel crashes when trying to start userspace if ARCH_PFN_OFFSET is
non-zero and CONFIG_BOOKE is not defined
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pseries: Export data from new hcall H_EM_GET_PARMS
Add support for H_EM_GET_PARMS hcall that will return data
related to power modes from the platform. Export the data
directly to user space for administrative tools to interpret
and use.
cat /proc/powerpc/lparcfg will export power mode data
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
K.Prasad [Mon, 29 Mar 2010 23:59:25 +0000 (23:59 +0000)]
powerpc: Disable interrupts for data breakpoint exceptions
Data address breakpoint exceptions are currently handled along with page-faults
which require interrupts to remain in enabled state. Since exception handling
for data breakpoints aren't pre-empt safe, we handle them separately.
Signed-off-by: K.Prasad <prasad@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Provide a modalias entry for VIO devices in sysfs. I believe
this was another initrd generation bugfix for anaconda. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Fix ioremap_flags() with book3e pte definition
We can't just clear the user read permission in book3e pte, because
that will also clear supervisor read permission. This surely isn't
desired. Fix the problem by adding the supervisor read back.
BenH: Slightly simplified the ifdef and applied to ppc64 too
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Corey Minyard [Fri, 29 Jan 2010 14:18:20 +0000 (14:18 +0000)]
powerpc: Add a new zImage for maple using a different link address
The maple platform failed to load because it's firmware could not take a
link address of 0x4000000. A new platform type with a link address of
0x400000 had to be created for the maple.
Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This driver seems to be specific to a "Sky CPU" board for which we
don't appear to have upstream support (or not any more). No Kconfig
file in the kernel ever enables it. So remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Force MSI irq handlers to run with interrupts disabled
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] hpwdt - fix lower timeout limit
[WATCHDOG] iTCO_wdt: TCO Watchdog patch for additional Intel Cougar Point DeviceIDs
[WATCHDOG] doc: Fix use of WDIOC_SETOPTIONS ioctl.
[WATCHDOG] doc: watchdog simple example: don't fail on fsync()
[WATCHDOG] set max63xx driver as ARM only
[WATCHDOG] powerpc: pika_wdt ident cannot be const
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
Some BIOSes don't configure HPA during boot but do so while resuming.
This causes harddrives to shrink during resume making libata detach
and reattach them. This can be worked around by unlocking HPA if old
size equals native size.
Add ATA_DFLAG_UNLOCK_HPA so that HPA unlocking can be controlled
per-device and update ata_dev_revalidate() such that it sets
ATA_DFLAG_UNLOCK_HPA and fails with -EIO when the above condition is
detected.
Thank you for contacting us. We know that with our M225 line of SSDs
you sometimes need to disable NCQ (native command queuing) to avoid
just the type of errors you're seeing. Our recommendation for the
M225 is to add libata.force=noncq to your Linux kernel boot options,
under the kernel ATA library option.
I have sent your feedback to the engineers working on the C300, and
asked them to please pass it on to the firmware team. I have been
notified that they are in the process of testing and finalizing a
new firmware version, that you can expect to see released around the
end of April. We’ll keep you posted as to when it will be available
for download.
So, turn off NCQ on the drive w/ the current firmware revision.
Reported in the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15573
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: lethalwp@scarlet.be Reported-by: Luke Macken <lmacken@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Wed, 31 Mar 2010 07:41:18 +0000 (16:41 +0900)]
libata: don't whine on spurious IRQ
On configurations where IRQ line is shared with a different
controller, spurious IRQs may happen continuously. The message was
put there primarily for debugging anyway. Kill it.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
James Hogan [Mon, 5 Apr 2010 10:31:29 +0000 (11:31 +0100)]
[WATCHDOG] doc: Fix use of WDIOC_SETOPTIONS ioctl.
In the watchdog-test program and watchdog-api.txt, pass the values to
the WDIOC_SETOPTIONS ioctl as a pointer to an integer containing the
values intead of directly in the third ioctl argument. The actual
watchdog drivers in drivers/watchdog don't read the options directly
from the argument but use get_user and copy_from_user.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Nick Piggin [Thu, 1 Apr 2010 08:09:40 +0000 (19:09 +1100)]
Fix up possibly racy module refcounting
Module refcounting is implemented with a per-cpu counter for speed.
However there is a race when tallying the counter where a reference may
be taken by one CPU and released by another. Reference count summation
may then see the decrement without having seen the previous increment,
leading to lower than expected count. A module which never has its
actual reference drop below 1 may return a reference count of 0 due to
this race.
Module removal generally runs under stop_machine, which prevents this
race causing bugs due to removal of in-use modules. However there are
other real bugs in module.c code and driver code (module_refcount is
exported) where the callers do not run under stop_machine.
Fix this by maintaining running per-cpu counters for the number of
module refcount increments and the number of refcount decrements. The
increments are tallied after the decrements, so any decrement seen will
always have its corresponding increment counted. The final refcount is
the difference of the total increments and decrements, preventing a
low-refcount from being returned.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla1280: retain firmware for error recovery
[SCSI] attirbute_container: Initialize sysfs attributes with sysfs_attr_init
[SCSI] advansys: fix regression with request_firmware change
[SCSI] qla2xxx: Updated version number to 8.03.02-k2.
[SCSI] qla2xxx: Prevent sending mbx commands from sysfs during isp reset.
[SCSI] qla2xxx: Disable MSI on qla24xx chips other than QLA2432.
[SCSI] qla2xxx: Check to make sure multique and CPU affinity support is not enabled at the same time.
[SCSI] qla2xxx: Correct vp_idx checking during PORT_UPDATE processing.
[SCSI] qla2xxx: Honour "Extended BB credits" bit for CNAs.
[SCSI] scsi_transport_fc: Make sure commands are completed when rport is offline
[SCSI] libiscsi: Fix recovery slowdown regression
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: saving negative to unsigned char
9p: return on mutex_lock_interruptible()
9p: Creating files with names too long should fail with ENAMETOOLONG.
9p: Make sure we are able to clunk the cached fid on umount
9p: drop nlink remove
fs/9p: Clunk the fid resulting from partial walk of the name
9p: documentation update
9p: Fix setting of protocol flags in v9fs_session_info structure.
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: add check for changed leaves in setup_leaf_for_split
Btrfs: create snapshot references in same commit as snapshot
Btrfs: fix small race with delalloc flushing waitqueue's
Btrfs: use add_to_page_cache_lru, use __page_cache_alloc
Btrfs: fix chunk allocate size calculation
Btrfs: kill max_extent mount option
Btrfs: fail to mount if we have problems reading the block groups
Btrfs: check btrfs_get_extent return for IS_ERR()
Btrfs: handle kmalloc() failure in inode lookup ioctl
Btrfs: dereferencing freed memory
Btrfs: Simplify num_stripes's calculation logical for __btrfs_alloc_chunk()
Btrfs: Add error handle for btrfs_search_slot() in btrfs_read_chunk_tree()
Btrfs: Remove unnecessary finish_wait() in wait_current_trans()
Btrfs: add NULL check for do_walk_down()
Btrfs: remove duplicate include in ioctl.c
Fix trivial conflict in fs/btrfs/compression.c due to slab.h include
cleanups.
Eric Paris [Mon, 5 Apr 2010 20:16:26 +0000 (16:16 -0400)]
audit: preface audit printk with audit
There have been a number of reports of people seeing the message:
"name_count maxed, losing inode data: dev=00:05, inode=3185"
in dmesg. These usually lead to people reporting problems to the filesystem
group who are in turn clueless what they mean.
Eventually someone finds me and I explain what is going on and that
these come from the audit system. The basics of the problem is that the
audit subsystem never expects a single syscall to 'interact' (for some
wish washy meaning of interact) with more than 20 inodes. But in fact
some operations like loading kernel modules can cause changes to lots of
inodes in debugfs.
There are a couple real fixes being bandied about including removing the
fixed compile time limit of 20 or not auditing changes in debugfs (or
both) but neither are small and obvious so I am not sending them for
immediate inclusion (I hope Al forwards a real solution next devel
window).
In the meantime this patch simply adds 'audit' to the beginning of the
crap message so if a user sees it, they come blame me first and we can
talk about what it means and make sure we understand all of the reasons
it can happen and make sure this gets solved correctly in the long run.
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Mon, 5 Apr 2010 19:37:28 +0000 (14:37 -0500)]
9p: saving negative to unsigned char
Saving -EINVAL as unsigned char truncates the high bits and changes it
into 234 instead of -22. This breaks the test for "if (ret == -EINVAL)"
in parse_opts().
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Dan Carpenter [Tue, 30 Mar 2010 09:41:25 +0000 (09:41 +0000)]
9p: return on mutex_lock_interruptible()
If "err" is -EINTR here the original code calls mutex_unlock() and then
returns, but it should just return directly.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
------------------------------------------------------------------------------
Download Intel® Parallel Studio Eval
Try the new software tools for yourself. Speed compiling, find bugs
proactively, and fine-tune applications for parallel performance.
See why Intel Parallel Studio got high marks during beta.
http://p.sf.net/sfu/intel-sw-dev
Chris Mason [Fri, 2 Apr 2010 13:20:18 +0000 (09:20 -0400)]
Btrfs: add check for changed leaves in setup_leaf_for_split
setup_leaf_for_split needs to drop the path and search again, and has
checks to see if the item we want to split changed size. But, it misses
the case where the leaf changed and now has enough room for the item
we want to insert.
This adds an extra check to make sure the leaf really needs splitting
before we call btrfs_split_leaf(), which keeps us from trying to split
a leaf with a single item.
btrfs_split_leaf() will blindly split the single item leaf, leaving us
with one good leaf and one empty leaf and then a crash.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Sage Weil [Mon, 15 Mar 2010 17:27:13 +0000 (17:27 +0000)]
Btrfs: create snapshot references in same commit as snapshot
This creates the reference to a new snapshot in the same commit as the
snapshot itself. This avoids the need for a second commit in order for a
snapshot to be persistent, and also avoids the problem of "leaking" a
new snapshot tree root if the host crashes before the second commit takes
place.
It is not at all clear to me why it wasn't always done this way. If there
is still a reason for the two-stage {create,finish}_pending_snapshots()
approach I'm missing something! :)
I've been running this for a couple weeks under pretty heavy usage (a few
snapshots per minute) without obvious problems.
Signed-off-by: Sage Weil <sage@newdream.net> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Fri, 12 Mar 2010 19:28:18 +0000 (19:28 +0000)]
Btrfs: fix small race with delalloc flushing waitqueue's
Everytime we start a new flushing thread, we init the waitqueue if there isn't a
flushing thread running. The problem with this is we check
space_info->flushing, which we clear right before doing a wake_up on the
flushing waitqueue, which causes problems if we init the waitqueue in the middle
of clearing the flushing flagh and calling wake_up. This is hard to hit, but
the code is wrong anyway, so init the flushing/allocating waitqueue when
creating the space info and let it be. I haven't seen the panic since I've been
using this patch. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Nick Piggin [Wed, 17 Mar 2010 13:31:04 +0000 (13:31 +0000)]
Btrfs: use add_to_page_cache_lru, use __page_cache_alloc
Pagecache pages should be allocated with __page_cache_alloc, so they
obey pagecache memory policies.
add_to_page_cache_lru is exported, so it should be used. Benefits over
using a private pagevec: neater code, 128 bytes fewer stack used, percpu
lru ordering is preserved, and finally don't need to flush pagevec
before returning so batching may be shared with other LRU insertions.
Signed-off-by: Nick Piggin <npiggin@suse.de>: Signed-off-by: Chris Mason <chris.mason@oracle.com>
Merge branch 'slabh' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc
* 'slabh' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc:
eeepc-wmi: include slab.h
staging/otus: include slab.h from usbdrv.h
percpu: don't implicitly include slab.h from percpu.h
kmemcheck: Fix build errors due to missing slab.h
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
iwlwifi: don't include iwl-dev.h from iwl-devtrace.h
x86: don't include slab.h from arch/x86/include/asm/pgtable_32.h
Fix up trivial conflicts in include/linux/percpu.h due to
is_kernel_percpu_address() having been introduced since the slab.h
cleanup with the percpu_up.c splitup.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
module: add stub for is_module_percpu_address
percpu, module: implement and use is_kernel/module_percpu_address()
module: encapsulate percpu handling better and record percpu_size
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Always build the powerpc perf_arch_fetch_caller_regs version
perf: Always build the stub perf_arch_fetch_caller_regs version
perf, probe-finder: Build fix on Debian
perf/scripts: Tuple was set from long in both branches in python_process_event()
perf: Fix 'perf sched record' deadlock
perf, x86: Fix callgraphs of 32-bit processes on 64-bit kernels
perf, x86: Fix AMD hotplug & constraint initialization
x86: Move notify_cpu_starting() callback to a later stage
x86,kgdb: Always initialize the hw breakpoint attribute
perf: Use hot regs with software sched switch/migrate events
perf: Correctly align perf event tracing buffer
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: set_cpus_allowed_ptr(): Don't use rq->migration_thread after unlock
sched: Fix proc_sched_set_task()
In initial design, walk_page_range() was designed just for walking page
table and it didn't require mmap_sem. Now, find_vma() etc.. are used
in walk_page_range() and we need mmap_sem around it.
This patch adds mmap_sem around walk_page_range().
Because /proc/<pid>/pagemap's callback routine use put_user(), we have
to get rid of it to do sane fix.
Changelog: 2010/Apr/2
- fixed start_vaddr and end overflow
Changelog: 2010/Apr/1
- fixed start_vaddr calculation
- removed unnecessary cast.
- removed unnecessary change in smaps.
- use GFP_TEMPORARY instead of GFP_KERNEL
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Matt Mackall <mpm@selenic.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: San Mehat <san@google.com> Cc: Brian Swetland <swetland@google.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org>
[ Fixed kmalloc failure return code as per Matt ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Sun, 4 Apr 2010 08:12:50 +0000 (01:12 -0700)]
sunxvr500: Ignore secondary output PCI devices.
These just represent the secondary and further heads attached to the
card, and they have different sets of PCI bar registers to map.
So don't try to drive them in the main driver.
Reported-by: Frans van Berckel <fberckel@xs4all.nl> Tested-by: Frans van Berckel <fberckel@xs4all.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Zyngier [Mon, 29 Mar 2010 19:09:14 +0000 (20:09 +0100)]
[WATCHDOG] set max63xx driver as ARM only
Use of ioremap() causes build failure on S390.
Restrict the driver to ARM until another architecture comes along
and enables the driver for its own use.
Signed-off-by: Marc Zyngier <maz@misterjones.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
projects / karo-tx-linux.git / log