V4L/DVB: tm6000: fix compilation due to the lack of a semicolon
Add a missing semicolon to fix this error:
In file included from drivers/staging/tm6000/tm6000-cards.c:32:
drivers/staging/tm6000/tm6000.h:123: error: two or more data types in
declaration specifiers
Randy Dunlap [Tue, 30 Mar 2010 17:32:04 +0000 (14:32 -0300)]
V4L/DVB: [-next] gspca: fix build for INPUT=m or INPUT=n
Handle case of GSPCA=m, INPUT=m when building gspca core;
also handle case of INPUT=n by using stubs.
drivers/media/video/gspca/gspca.c:662: error: implicit declaration of function 'gspca_input_destroy_urb'
drivers/media/video/gspca/gspca.c:668: error: implicit declaration of function 'gspca_input_create_urb'
drivers/media/video/gspca/gspca.c:2284: error: implicit declaration of function 'gspca_input_connect'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri Belimov [Tue, 30 Mar 2010 06:02:17 +0000 (03:02 -0300)]
V4L/DVB: Fix default state Beholder H6 tuner
The hybrid tuner FMD1216MEX_MK3 after cold start has disabled IF. This
tuner has internal I2C switch. This switch switch I2C bus between DVB-T
and IF part. Default state is DVB-T. When module saa7134 is load it
can't find IF tda9887 and disable analog TV mode.
Sets internal I2C switch of the tuner to IF by send special value to the
tuner as for receive analog TV from low band. It can be usefule for
other cards.
I didn't set configure a tuner by a tuner model because this tuner can
have different I2C address. May be we can do it later after discuss for
more robust support a tuners.
Dean Anderson [Fri, 9 Apr 2010 02:46:08 +0000 (23:46 -0300)]
V4L/DVB: s2255drv: removal of big kernel lock
big kernel lock removed from open function.
v4l2 code does not require locking the open function except
to check asynchronous firmware load state, which is protected
by a mutex
Signed-off-by: Dean Anderson <dean@sensoray.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch fixes code that checks for CX88_VMUX_TELEVISION,
but not CX88_VMUX_CABLE. This prevented for example the audio standard
from being set when using the cable input.
Nicolas Noirbent [Mon, 22 Mar 2010 17:54:43 +0000 (14:54 -0300)]
V4L/DVB: ds3000: fix divide-by-zero error in ds3000_read_snr()
Fix a divide-by-zero error in ds3000's ds3000_read_snr(), when getting
a very low signal reading (dvbs2_signal_reading >= 1). This prevents
some nasty EIPs when running szap-s2 with a very low signal strength.
Signed-off-by: Nicolas Noirbent <nicolas.noirbent@smartjog.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: ir-core: Remove warining noise if decoders compiled builtin
drivers/media/IR/ir-raw-event.c:55: warning: ‘wq_load’ defined but not used
drivers/media/IR/ir-raw-event.c:222: warning: ‘init_decoders’ defined but not used
drivers/media/IR/rc-map.c: In function ‘get_rc_map’:
drivers/media/IR/rc-map.c:40: warning: unused variable ‘rc’
Andreas Bombe [Sun, 21 Mar 2010 19:02:45 +0000 (16:02 -0300)]
V4L/DVB: V4L2: Replace loops for finding max buffers in VIDIOC_REQBUFS callbacks
Due to obvious copy and paste coding a number of video capture drivers
which implement a limit on the buffer memory decremented the user
supplied buffer count in a while loop until it reaches an acceptable
value.
This is a silly thing to do when the maximum value can be directly
computed.
Signed-off-by: Andreas Bombe <aeb@debian.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On newer kernels, a saa7134 board stopped to display TV video output
properly. After a bisect, I found it as the commit causing the issue.
Turns out that v4l_bound_align_image isn't doing the same bounding
calculation as manually done previously in saa7134_try_fmt_vid_cap.
What isn't equal is the calculation done in clamp align, while
previously it did "f->fmt.pix.width &= ~0x03", clamp_align function
does "Round to nearest aligned value" as stated in the comment, which
yields a different result. If I comment the round calculation in
clamp_align like this: "x = (x /*+ (1 << (align - 1))*/) & mask",
I get it fixed too, because this way the calculation is the same then.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wolfram Sang [Mon, 5 Apr 2010 04:14:26 +0000 (01:14 -0300)]
V4L/DVB: dvb/dib8000: fix build warning
In file included from drivers/media/dvb/dvb-usb/dib0700_devices.c:14:
drivers/media/dvb/frontends/dib8000.h: In function 'dib8000_get_adc_power':
drivers/media/dvb/frontends/dib8000.h:112: warning: no return statement in function returning non-void
Fixed by adding a return to the dummy function.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 6 Apr 2010 18:56:08 +0000 (15:56 -0300)]
V4L/DVB: video_ioctl2: handle the v4l1 compat bit first and move VIDIOCGMBUF into the switch
Try to make a more sensible sequence of events in __video_do_ioctl: first
check for a valid ops pointer, then get the compat part done. The VIDIOCGMBUF
command is now part of the big switch.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 6 Apr 2010 14:36:39 +0000 (11:36 -0300)]
V4L/DVB: w9966: convert to V4L2
Note that I have not been able to find anyone with this hardware. I tried
contacting the author without success, searched on eBay and similar places
without luck either.
So this conversion is untested. That said, it was pretty straightforward
so it is time to have this driver join the V4L2 world at last.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 6 Apr 2010 11:20:56 +0000 (08:20 -0300)]
V4L/DVB: usbvision: remove non-working vbi device
The usbvision driver created vbi device nodes but the actual implementation
was just stubs and only returned errors to userspace.
In addition it used video_usercopy() and we want to remove that eventually.
So remove all the vbi code except for the vbi flag in the card definition
should someone ever be mad enough to work on a proper implementation for this
driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Wed, 7 Apr 2010 09:21:05 +0000 (06:21 -0300)]
V4L/DVB: davinci: don't return under lock on error path
If the kmalloc() failed for "ccdc_cfg = kmalloc(...);" then we would exit
with the lock held. I moved the mutex_lock() below the allocation
because it isn't protecting anything in that block and allocations are
allocations are sometimes slow.
V4L/DVB: ir-core: move subsystem internal calls to ir-core-priv.h
ir-core.h has the kABI to be used by the bridge drivers, when needing to register
IR protocols and pass IR events. However, the same file also contains IR subsystem
internal calls, meant to be used inside ir-core and between ir-core and the raw
decoders.
Better to move those functions to an internal header, for some reasons:
1) Header will be a little more cleaner;
2) It avoids the need of recompile everything (bridge/hardware drivers, etc),
just because a new decoder were added, or some other internal change were needed;
3) Better organize the ir-core API, splitting the functions that are internal to
IR core and the ancillary drivers (decoders, lirc_dev) from the features that
should be exported to IR subsystem clients.
David Härdeman [Thu, 8 Apr 2010 16:10:00 +0000 (13:10 -0300)]
V4L/DVB: Teach drivers/media/IR/ir-raw-event.c to use durations
drivers/media/IR/ir-raw-event.c is currently written with the assumption
that all "raw" hardware will generate events only on state change (i.e.
when a pulse or space starts).
However, some hardware (like mceusb, probably the most popular IR receiver
out there) only generates duration data (and that data is buffered so using
any kind of timing on the data is futile).
Furthermore, using signed int's to represent pulse/space durations is a
well-known approach when writing ir decoders.
With this patch:
- s64 int's are used to represent pulse/space durations in ns
- a workqueue is used to decode the ir protocols outside of interrupt context
- #defines are added to make decoders clearer
- decoder reset is implemented by passing a zero duration to the kfifo queue
and decoders are updated accordingly
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/IR/ir-sysfs.c: In function ‘store_protocol’:
drivers/media/IR/ir-sysfs.c:93: warning: suggest parentheses around assignment used as truth value
V4L/DVB: ir-core: properly present the supported and current protocols
Hardware decoders have a more limited set of decoders than software ones.
In general, they support just one protocol at a given time, but allow
changing between a few options.
Rename the previous badly named "current_protocol" as just "protocol",
meaning the current protocol(s) accepted by the driver, and
add a "support_protocols" to represent the entire universe of supported
protocols by that specific hardware.
As commented on http://lwn.net/Articles/378884/, the "one file, one value"
rule doesn't fit nor does make much sense for bitmap or enum values. So, the
supported_protocols will enum all supported protocols, and the protocol
will present all active protocols.
V4L/DVB: ir-core: Distinguish sysfs attributes for in-hardware and raw decoders
Some devices have in-hardware Remote Controller decoder, while others
need a software decoder to get the IR code. As each software decoder
can be enabled/disabled individually, allowing multiple protocol
decoding capability.
On the other hand, hardware decoders have a limited protocol
support, often being able of decoding just one protocol each time.
So, each type needs a different set of capabilities to control the
supported protocol(s).
David Härdeman [Sun, 28 Mar 2010 21:38:49 +0000 (18:38 -0300)]
V4L/DVB: rename sysfs remote controller devices from rcrcv to rc
When the remote controller class is anyway being renamed from ir to rc
this would be a good time to also rename the devices from rcrcvX to rcX.
I know we haven't reached any agreement on whether transmission will
eventually be handled by the same device, but this change will at
least make the device name non-receive-specific which will make it
possible in the future (and if a different approach is finally
agreed upon, the device name still works).
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
So, use static initialization for the static spinlocks, instead of the
dynamic ones (currently used), as proposed by David Härdeman on one
of his RFC patches.
V4L/DVB: em28xx: fix a regression caused by the rc-map changes
The patch that adds the rc-map changes didn't take into account that an
a table with IR_TYPE_UNKNOWN would make change_protocol to return -EINVAL.
As this function is fundamental to initialize some data, including a
callback to the getkey function, this caused the driver to stop working,
hanging the machine most of the times.
The fix were simply to add a handler for the IR type, but, to avoid further
issues, explicitly call change_protocol and handle the error before
initializing the IR. Also, let input_dev to start/stop IR handling,
after the opening of the input device.
V4L/DVB: ir-core: Add support for badly-implemented hardware decoders
A few hardware Remote Controller decoders, even using a standard protocol,
aren't able to provide the entire scancode. Due to that, the capability
of using other IR's are limited on those hardware.
Adds a way to indicate to ir-core what are the bits that the hardware
provides, from a scancode, allowing the addition of a complete IR table
to the kernel and allowing a limited support for changing the Remote
Controller on those devices.
The keymaps don't need to be recompiled every time a change at ir-core.h
happens, since it only depends on rc-map defines. By moving those
definitions to the proper header, the code became cleaner, and avoids
needing to recompile all the RC maps every time a non-related change
is introduced.
Now that the decoders are state machine, there's no need to create
an ancillary buffer while decoding the protocol. Just call the decoders
code directly, event by event.
V4L-DVB: ir-rc5-decoder: Add a decoder for RC-5 IR protocol
This decoder is also based on a state machine, just like the NEC protocol
decoder. It is pedantic in the sense that accepts only 14 bits. As there
are some variants that outputs less bits, it needs to be improved to also
handle those.
V4L/DVB: ir-nec-decoder: Reimplement the entire decoder
Thanks to Andy Walls <awalls@md.metrocast.net> for pointing me his
code, that gave me some ideas to better implement it.
After some work with saa7134 bits, I found a way to catch both IRQ
edge pulses. By enabling it, the NEC decoder can now take both
pulse and spaces into account, making it more precise.
Instead of the old strategy of handling the events all at once,
this code implements a state machine. Due to that, it handles
individual pulse or space events, validating them against the
protocol, producing a much more reliable decoding.
With the new implementation, the protocol trailer bits are properly
handled, making possible for the repeat key to work.
Also, the code is now capable of handling both NEC and NEC extended
IR devices. With NEC, it produces a 16 bits code, while with NEC
extended, a 24 bits code is returned.
David Härdeman [Fri, 2 Apr 2010 18:58:30 +0000 (15:58 -0300)]
V4L/DVB: Convert drivers/media/dvb/ttpci/budget-ci.c to use ir-core
Converts drivers/media/dvb/ttpci/budget-ci.c to use ir-core rather than
rolling its own keydown timeout handler and reporting keys via
drivers/media/IR/ir-functions.c.
[mchehab@redhat.com: Drop the call to ir_input_init() as it is no longer needed]
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
David Härdeman [Fri, 2 Apr 2010 18:58:29 +0000 (15:58 -0300)]
V4L/DVB: ir-core: improve keyup/keydown logic
Rewrites the keyup/keydown logic in drivers/media/IR/ir-keytable.c.
All knowledge of keystates etc is now internal to ir-keytable.c
and not scattered around ir-raw-event.c and ir-nec-decoder.c (where
it doesn't belong).
In addition, I've changed the API slightly so that ir_input_dev is
passed as the first argument rather than input_dev. If we're ever
going to support multiple keytables we need to move towards making
ir_input_dev the main interface from a driver POV and obscure away
the input_dev as an implementational detail in ir-core.
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
David Härdeman [Fri, 2 Apr 2010 18:58:28 +0000 (15:58 -0300)]
V4L/DVB: drivers/media/IR - improve keytable code
The attached patch rewrites much of the keytable code in
drivers/media/IR/ir-keytable.c.
The scancodes are now inserted into the array in sorted
order which allows for a binary search on lookup.
The code has also been shrunk by about 150 lines.
In addition it fixes the following bugs:
Any use of ir_seek_table() was racy.
ir_dev->driver_name is leaked between ir_input_register() and
ir_input_unregister().
ir_setkeycode() unconditionally does clear_bit() on dev->keybit
when removing a mapping, but there might be another mapping with
a different scancode and the same keycode.
This version has been updated to incorporate patch feedback from
Mauro Carvalho Chehab.
[mchehab@redhat.com: Fix a conflict with RC keytable breakup patches and input changes]
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB: saa7134: Add support for both positive and negative edge IRQ
The code that enables IRQ for the Remote Controller on saa7134 is a little
messy: it is outside saa7134-input, it checks if RC is GPIO based, and
it mixes both serial raw decode with parallel reads from a hardware-based
IR decoder.
Also, currently, it doesn't allow to trigger both transition edges at GPIO16
and GPIO18 lines. A rework on the code is needed to provide a better way
to specify what saa7134-input needs, maybe even moving part of the code from
saa7134-core and saa7134-cards into saa7134-input.
Yet, as a large rework is happening at RC core, it is better to wait until
the core changes stablize, in order to rework saa7134 RC internals.While
this don't happen, let's just change the logic a little bit to allow
enabling IRQ to be generated on both edge transitions, in order to better
support pulse/space raw decoders.
V4L/DVB: saa7134: Fix IRQ2 bit names for the register map
There's an error at the IRQ2 bit map registers. Also, it doesn't
show what bits are needed for positive and for negative edge.
In the case of IR raw decoding, for some protocols, it is important
to detect both positive and negative edges. So, a latter patch
will need to use the other values.
Also, the code that detects problems on IRQ handling is incomplete,
as it disables only one of the IRQ bits for GPIO16 and GPIO18.
V4L/DVB: ir-core: Make use of the new IR keymap modules
Instead of using the ugly keymap sequences, use the new rc-*.ko keymap
files. For now, it is still needed to have one keymap loaded, for the
RC code to work. Later patches will remove this depenency.
V4L/DVB: Break Remote Controller keymaps into modules
The original Remote Controller approach were very messy: a big file,
that were part of ir-common kernel module, containing 64 different
RC keymap tables, used by the V4L/DVB drivers.
Better to break each RC keymap table into a separate module,
registering them into rc core on a process similar to the fs/nls tables.
As an userspace program is now in charge of loading those tables,
adds an option to allow the complete removal of those tables from
kernelspace.
Yet, on embedded devices like Set Top Boxes and TV sets, maybe the
only available input device is the IR. So, we should keep allowing
the usage of in-kernel tables, but a latter patch should change
the default to 'n', after giving some time for distros to add
the v4l-utils with the ir-keytable program, to allow the table
load via userspace.
V4L/DVB: ir-core: Add support for RC map code register
Instead of having all RC tables hardcoded on one file with
all tables there, add infrastructure for registering and dynamically
load the table(s) when needed.
V4L/DVB: ir-common: Use macros to define the keytables
The usage of macros ensures that the proper namespace is being used
by all tables. It also makes easier to associate a keytable with
the name used inside the drivers.
V4L/DVB: ir-common: Use a function to declare an IR table
This is the first patch of a series of changes that will break the IR
tables into a series of small modules that can be dynamically loaded,
or just loaded from userspace.
V4L/DVB: ir-core: rename sysfs remote controller class from ir to rc
IR is an alias for Infrared Remote, while RC is an alias for Remote
Controller.
While currently all implementations are with Infrared Remote Controller,
this subsystem is not meant to be used only by IR type of RC's. So,
as discussed on both linux-media and linux-input, the better is to
rename the subsystem as Remote Controller.
While, currently, the only application that uses the /sys/class/irrcv is
ir-keytable application, and its sysfs support works only with the
current linux-next code, it is still possible to change the userspace API
without the risk of breaking applications. So, better to rename this
sooner than later.
Later patches will be needed to rename the files and to move them away
from drivers/media, but this is not a critical issue. So, for now,
let's just change the name of the sysfs class/nodes.
V4L/DVB: ir-core: prepare to add more operations for ir decoders
Some decoders and a lirc_dev interface may need some other operations to work.
For example: IR device register/unregister and ir_keydown events may need to
be tracked.
As some operations can occur in interrupt time, and a lock is needed to prevent
un-registering a decode while decoding a key, the lock needed to be convert
into a spin lock.
V4L/DVB: ir-core: dynamically load the compiled IR protocols
Instead of hardcoding the protocols into ir-core, add a register interface
for the IR protocol decoders, and convert ir-nec-decoder into a client of
ir-core.
With this approach, it is possible to dynamically load the needed IR protocols,
and to add a RAW IR interface module, registered as one IR raw protocol decoder.
This patch opens a way to register a lirc_dev interface to work as an userspace
IR protocol decoder.
V4L/DVB: saa7134: don't wait too much to generate an IR event on raw_decode
At raw_decode mode, the key is processed after the end of a timer. The
previous code resets the timer every time something is received at the IR
port. While this works fine with IR's that don't implement repeat, like
Avermedia RM-JX IR, it keeps waiting until keydown, on IR's that implement
NEC repeat command, like the Terratec yellow.
The solution is to change the behaviour to do the timeout after the first
received data.
The timeout is currently set to 15 ms, as it works fine with NEC protcocol.
It may need some adjustments to support other protocols and to better handle
spurious detections that may happen with some IR sensors.
projects / linux-beck.git / log