The copy of /proc/vmcore to a user buffer proceeds much faster
if the kernel addresses memory as cached.
With this patch we have seen an increase in transfer rate from
less than 15MB/s to 80-460MB/s, depending on size of the
transfer. This makes a big difference in time needed to save a
system dump.
Currently the redirection hint in the interrupt-remapping table entry
is set to 0, which means the remapped interrupt is directed to the
processors listed in the destination. So in logical flat mode
in the presence of intr-remapping, this results in a single
interrupt multi-casted to multiple cpu's as specified by the destination
bit mask. But what we really want is to send that interrupt to one of the cpus
based on the lowest priority delivery mode.
Set the redirection hint in the IRTE to '1' to indicate that we want
the remapped interrupt to be directed to only one of the processors
listed in the destination.
This fixes the issue of same interrupt getting delivered to multiple cpu's
in the logical flat mode in the presence of interrupt-remapping. While
there is no functional issue observed with this behavior, this will
impact performance of such configurations (<=8 cpu's using logical flat
mode in the presence of interrupt-remapping)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100827181049.013051492@sbsiddha-MOBL3.sc.intel.com> Cc: Weidong Han <weidong.han@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of adapting the CPU family check in amd_special_default_mtrr()
for each new CPU family assume that all new AMD CPUs support the
necessary bits in SYS_CFG MSR.
Tom2Enabled is architectural (defined in APM Vol.2).
Tom2ForceMemTypeWB is defined in all BKDGs starting with K8 NPT.
In pre K8-NPT BKDG this bit is reserved (read as zero).
W/o this adaption Linux would unnecessarily complain about bad MTRR
settings on every new AMD CPU family, e.g.
[ 0.000000] WARNING: BIOS bug: CPU MTRRs don't cover all of memory, losing 4863MB of RAM.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100930123235.GB20545@loge.amd.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x86 smp_ops now has a new op, stop_other_cpus which takes a parameter
"wait" this allows the caller to specify if it wants to stop until all
the cpus have processed the stop IPI. This is required specifically
for the kexec case where we should wait for all the cpus to be stopped
before starting the new kernel. We now wait for the cpus to stop in
all cases except for panic/kdump where we expect things to be broken
and we are doing our best to make things work anyway.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
LKML-Reference: <1286833028.1372.20.camel@ank32.eng.vmware.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The AMD SSE5 feature set as-it has been replaced by some extensions
to the AVX instruction set. Thus the bit formerly advertised as SSE5
is re-used for one of these extensions (XOP).
Although this changes the /proc/cpuinfo output, it is not user visible, as
there are no CPUs (yet) having this feature.
To avoid confusion this should be added to the stable series, too.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
LKML-Reference: <1283778860-26843-2-git-send-email-andre.przywara@amd.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During the reading of /proc/vmcore the kernel is doing
ioremap()/iounmap() repeatedly. And the buildup of un-flushed
vm_area_struct's is causing a great deal of overhead. (rb_next()
is chewing up most of that time).
This solution is to provide function set_iounmap_nonlazy(). It
causes a subsequent call to iounmap() to immediately purge the
vma area (with try_purge_vmap_area_lazy()).
With this patch we have seen the time for writing a 250MB
compressed dump drop from 71 seconds to 44 seconds.
futex_wait() is leaking key references due to futex_wait_setup()
acquiring an additional reference via the queue_lock() routine. The
nested key ref-counting has been masking bugs and complicating code
analysis. queue_lock() is only called with a previously ref-counted
key, so remove the additional ref-counting from the queue_(un)lock()
functions.
Also futex_wait_requeue_pi() drops one key reference too many in
unqueue_me_pi(). Remove the key reference handling from
unqueue_me_pi(). This was paired with a queue_lock() in
futex_lock_pi(), so the count remains unchanged.
Document remaining nested key ref-counting sites.
Signed-off-by: Darren Hart <dvhart@linux.intel.com> Reported-and-tested-by: Matthieu Fertré<matthieu.fertre@kerlabs.com> Reported-by: Louis Rilling<louis.rilling@kerlabs.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: John Kacur <jkacur@redhat.com> Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <4CBB17A8.70401@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The logic to distinguish marked instruction events from ordinary events
on PPC970 and derivatives was flawed. The result is that instruction
sampling didn't get enabled in the PMU for some marked instruction
events, so they would never trigger. This fixes it by adding the
appropriate break statements in the switch statement.
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Event thread wakes up and passes the event to
event_handler() to process.
- It processes and clears the USBIP_EH_SHUTDOWN
flag then returns.
- The outer event loop (event_handler_loop()) calls
wait_event_interruptible().
The processing of the second flag which is part of
VDEV_EVENT_DOWN (USBIP_EH_RESET) did not happen yet.
It is delayed until the next event.
This means the ->reset callback may not happen for
a long time (if ever), leaving the usbip port in a
weird state which prevents its reuse.
This patch changes the handler to process all flags
before waiting for another wakeup.
I have verified this change to fix a problem which
prevented reattach of a usbip device. It also helps
for socket errors which missed the RESET as well.
The delayed event processing also affects the stub
side of usbip and the error handling there.
Signed-off-by: Max Vozeler <mvz@vozeler.com> Reported-by: Marco Lancione <marco@optikam.com> Tested-by: Luc Jalbert <ljalbert@optikam.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Network namespace in the Phonet socket stack causes an OOPS when a
namespace is destroyed. This occurs as the loopback exit_net handler is
called after the Phonet exit_net handler, and re-enters the Phonet
stack. I cannot think of any nice way to fix this in kernel <= 2.6.32.
For lack of a better solution, disable namespace support completely.
If you need that, upgrade to a newer kernel.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Ben Hutchings <ben@decadent.org.uk> Acked-by: David S. Miller <davem@davemloft.net>
An execve with a very large total of argument/environment strings
can take a really long time in the execve system call. It runs
uninterruptibly to count and copy all the strings. This change
makes it abort the exec quickly if sent a SIGKILL.
Note that this is the conservative change, to interrupt only for
SIGKILL, by using fatal_signal_pending(). It would be perfectly
correct semantics to let any signal interrupt the string-copying in
execve, i.e. use signal_pending() instead of fatal_signal_pending().
We'll save that change for later, since it could have user-visible
consequences, such as having a timer set too quickly make it so that
an execve can never complete, though it always happened to work before.
This adds a preemption point during the copying of the argument and
environment strings for execve, in copy_strings(). There is already
a preemption point in the count() loop, so this doesn't add any new
points in the abstract sense.
When the total argument+environment strings are very large, the time
spent copying them can be much more than a normal user time slice.
So this change improves the interactivity of the rest of the system
when one process is doing an execve with very large arguments.
The CONFIG_STACK_GROWSDOWN variant of setup_arg_pages() does not
check the size of the argument/environment area on the stack.
When it is unworkably large, shift_arg_pages() hits its BUG_ON.
This is exploitable with a very large RLIMIT_STACK limit, to
create a crash pretty easily.
Check that the initial stack is not too large to make it possible
to map in any executable. We're not checking that the actual
executable (or intepreter, for binfmt_elf) will fit. So those
mappings might clobber part of the initial stack mapping. But
that is just userland lossage that userland made happen, not a
kernel problem.
Some extra CPU features such as ARAT is needed in early boot so
that x86_init function pointers can be set up properly.
http://lkml.org/lkml/2010/5/18/519
At start_kernel() level, this patch moves init_scattered_cpuid_features()
from check_bugs() to setup_arch() -> early_cpu_init() which is earlier than
platform specific x86_init layer setup. Suggested by HPA.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
LKML-Reference: <1274295685-6774-2-git-send-email-jacob.jun.pan@linux.intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Section 4.7.3.1.1 (PM1 Status Registers) of version 4.0 of
the ACPI spec concerning PCIEXP_WAKE_STS points out in
in the final note field in table 4-11 that if this bit is
set to 1 and the system is put into a sleeping state then
the system will not automatically wake.
This bit gets set by hardware to indicate that the system
woke up due to a PCI Express wakeup event, so clear it during
acpi_hw_clear_acpi_status() calls to enable subsequent
resumes to work.
BugLink: http://bugs.launchpad.net/bugs/613381 Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For carrier detection to work properly when binding the driver with a cable
unplugged, netif_carrier_off() should be called after register_netdev(),
not before.
Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately, this stack pointer can't be used when translation is off
on PHYP as this stack pointer might be outside the RMO. This results in
the following on all non zero cpus:
cpu 0x1: Vector: 300 (Data Access) at [c00000001639fd10]
pc: 000000000001c50c
lr: 000000000000821c
sp: c00000001639ff90
msr: 8000000000001000
dar: c00000001639ffa0
dsisr: 42000000
current = 0xc000000016393540
paca = 0xc000000006e00200
pid = 0, comm = swapper
The original patch was only tested on bare metal system, so it never
caught this problem.
This changes __secondary_start so that we calculate the new stack
pointer but only start using it after we've called early_setup_secondary.
With this patch, the above problem goes away.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As early setup calls down to slb_initialize(), we must have kstack
initialised before checking "should we add a bolted SLB entry for our kstack?"
Failing to do so means stack access requires an SLB miss exception to refill
an entry dynamically, if the stack isn't accessible via SLB(0) (kernel text
& static data). It's not always allowable to take such a miss, and
intermittent crashes will result.
Primary CPUs don't have this issue; an SLB entry is not bolted for their
stack anyway (as that lives within SLB(0)). This patch therefore only
affects the init of secondaries.
Signed-off-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After walking the multicast list to set up the hash filter, this
function will walk off the end of the list when filling the
exact-match entries. This was fixed in mainline by the interface
change made in commit f9dcbcc9e338d08c0f7de7eba4eaafbbb7f81249.
Reported-by: spamalot@hispeed.ch
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=15355 Reported-by: Jason Heeris <jason.heeris@gmail.com>
Reference: http://bugs.debian.org/600155 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As reported in <https://bugzilla.kernel.org/show_bug.cgi?id=15355>, r6040_
multicast_list currently crashes. This is due a wrong maximum of multicast
entries. This patch fixes the following issues with multicast:
- number of maximum entries if off-by-one (4 instead of 3)
- the writing of the hash table index is not necessary and leads to invalid
values being written into the MCR1 register, so the MAC is simply put in a non
coherent state
- when we exceed the maximum number of mutlticast address, writing the
broadcast address should be done in registers MID_1{L,M,H} instead of
MID_O{L,M,H}, otherwise we would loose the adapter's MAC address
[bwh: Adjust for 2.6.32; should also apply to 2.6.27]
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have fedora bug report where driver fail to initialize after
suspend/resume because of memory allocation errors:
https://bugzilla.redhat.com/show_bug.cgi?id=629158
To fix use GFP_KERNEL allocation where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Skge devices installed on some Gigabyte motherboards are not able to
perform 64 dma correctly due to board PCI implementation, so limit
DMA to 32bit if such boards are detected.
Bug was reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=447489
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Tested-by: Luya Tshimbalanga <luya@fedoraproject.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Blackhole routes are used when xfrm_lookup() returns -EREMOTE (error
triggered by IKE for example), hence this kind of route is always
temporary and so we should check if a better route exists for next
packets.
Bug has been introduced by commit d11a4dc18bf41719c9f0d7ed494d295dd2973b92.
Signed-off-by: Jianzhao Wang <jianzhao.wang@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just use explicit casts, since we really can't change the
types of structures exported to userspace which have been
around for 15 years or so.
Reported-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a RST comes in immediately after checking sk->sk_err, tcp_poll will
return POLLIN but not POLLOUT. Fix this by checking sk->sk_err at the end
of tcp_poll. Additionally, ensure the correct order of operations on SMP
machines with memory barriers.
Signed-off-by: Tom Marshall <tdm.code@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several other ethtool functions leave heap uncleared (potentially) by
drivers. Some interfaces appear safe (eeprom, etc), in that the sizes
are well controlled. In some situations (e.g. unchecked error conditions),
the heap will remain unchanged in areas before copying back to userspace.
Note that these are less of an issue since these all require CAP_NET_ADMIN.
Cc: stable@kernel.org Signed-off-by: Kees Cook <kees.cook@canonical.com> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Special care should be taken when slow path is hit in ip_fragment() :
When walking through frags, we transfert truesize ownership from skb to
frags. Then if we hit a slow_path condition, we must undo this or risk
uncharging frags->truesize twice, and in the end, having negative socket
sk_wmem_alloc counter, or even freeing socket sooner than expected.
Many thanks to Nick Bowler, who provided a very clean bug report and
test program.
Thanks to Jarek for reviewing my first patch and providing a V2
While Nick bisection pointed to commit 2b85a34e911 (net: No more
expensive sock_hold()/sock_put() on each tx), underlying bug is older
(2.6.12-rc5)
A side effect is to extend work done in commit b2722b1c3a893e
(ip_fragment: also adjust skb->truesize for packets not owned by a
socket) to ipv6 as well.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com> Tested-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Jarek Poplawski <jarkao2@gmail.com> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the condition (3rd arg) passed to sk_wait_event() in
sk_stream_wait_memory(). The incorrect check in sk_stream_wait_memory()
causes the following soft lockup in tcp_sendmsg() when the global tcp
memory pool has exhausted.
What is happening is, that the sk_wait_event() condition passed from
sk_stream_wait_memory() evaluates to true for the case of tcp global memory
exhaustion. This is because both sk_stream_memory_free() and vm_wait are true
which causes sk_wait_event() to *not* call schedule_timeout().
Hence sk_stream_wait_memory() returns immediately to the caller w/o sleeping.
This causes the caller to again try allocation, which again fails and again
calls sk_stream_wait_memory(), and so on.
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tcp_sendmsg() truncates iov_len to an 'int' which a 4GB write to write
zero bytes, for example.
There is also the problem higher up of how verify_iovec() works. It
wants to prevent the total length from looking like an error return
value.
However it does this using 'int', but syscalls return 'long' (and
thus signed 64-bit on 64-bit machines). So it could trigger
false-positives on 64-bit as written. So fix it to use 'long'.
Reported-by: Olaf Bonorden <bono@onlinehome.de> Reported-by: Daniel Büse <dbuese@gmx.de> Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dont compare ECN and IP Precedence bits in find_bundle
and use ECN bit stripped TOS value in xfrm_lookup
Signed-off-by: Ulrich Weber <uweber@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't try to "optimize" rds_page_copy_user() by using kmap_atomic() and
the unsafe atomic user mode accessor functions. It's actually slower
than the straightforward code on any reasonable modern CPU.
Back when the code was written (although probably not by the time it was
actually merged, though), 32-bit x86 may have been the dominant
architecture. And there kmap_atomic() can be a lot faster than kmap()
(unless you have very good locality, in which case the virtual address
caching by kmap() can overcome all the downsides).
But these days, x86-64 may not be more populous, but it's getting there
(and if you care about performance, it's definitely already there -
you'd have upgraded your CPU's already in the last few years). And on
x86-64, the non-kmap_atomic() version is faster, simply because the code
is simpler and doesn't have the "re-try page fault" case.
People with old hardware are not likely to care about RDS anyway, and
the optimization for the 32-bit case is simply buggy, since it doesn't
verify the user addresses properly.
Reported-by: Dan Rosenberg <drosenberg@vsecurity.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes possible cases of not collecting valid error info in
the MCE error thresholding groups on F10h hardware.
The current code contains a subtle problem of checking only the
Valid bit of MSR0000_0413 (which is MC4_MISC0 - DRAM
thresholding group) in its first iteration and breaking out if
the bit is cleared.
But (!), this MSR contains an offset value, BlkPtr[31:24], which
points to the remaining MSRs in this thresholding group which
might contain valid information too. But if we bail out only
after we checked the valid bit in the first MSR and not the
block pointer too, we miss that other information.
The thing is, MC4_MISC0[BlkPtr] is not predicated on
MCi_STATUS[MiscV] or MC4_MISC0[Valid] and should be checked
prior to iterating over the MCI_MISCj thresholding group,
irrespective of the MC4_MISC0[Valid] setting.
adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com> Acked-by: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver doesn't fill the entire buffer, old
heap contents may remain, and if it also doesn't
update the length properly, this old heap content
will be copied back to userspace.
It is very unlikely that this happens in any of
the drivers using private ioctls since it would
show up as junk being reported by iwpriv, but it
seems better to be safe here, so use kzalloc.
Reported-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ocfs2 fast symlinks are NUL terminated strings stored inline in the
inode data area. However, disk corruption or a local attacker could, in
theory, remove that NUL. Because we're using strlen() (my fault,
introduced in a731d1 when removing vfs_follow_link()), we could walk off
the end of that string.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ret is still -1, if during the polling read_byte() returns at once
with I2C_PCA_CON_SI set. So ret > 0 would lead *_waitforcompletion()
to return 0, in spite of the proper behavior.
The routine was rewritten, so that ret has always a proper value,
before returning.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CPU X CPU Y
remove_hrtimer
// state & QUEUED == 0
timer->state = CALLBACK
unlock timer base
timer->f(n) //very long
hrtimer_start
lock timer base
remove_hrtimer // no effect
hrtimer_enqueue
timer->state = CALLBACK |
QUEUED
unlock timer base
hrtimer_start
lock timer base
remove_hrtimer
mode = INACTIVE
// CALLBACK bit lost!
switch_hrtimer_base
CALLBACK bit not set:
timer->base
changes to a
different CPU.
lock this CPU's timer base
The bug was introduced with commit ca109491f (hrtimer: removing all ur
callback modes) in 2.6.29
[ tglx: Feed new state via local variable and add a comment. ]
Signed-off-by: Salman Qazi <sqazi@google.com> Cc: akpm@linux-foundation.org Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20101012142351.8485.21823.stgit@dungbeetle.mtv.corp.google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using simultaneously the two DMA channels on a same engine, some
transfers are never completed. For example, an endless lock can occur
while writing heavily on a RAID5 array (with async-tx offload support
enabled).
Note that this issue can also be reproduced by using the DMA test
client.
On a same engine, the interrupt cause register is shared between two
DMA channels. This patch make sure that the cause bit is only cleared
for the requested channel.
Signed-off-by: Simon Guinot <sguinot@lacie.com> Tested-by: Luc Saillard <luc@saillard.org> Acked-by: saeed bishara <saeed.bishara@gmail.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Time stamps for the ring buffer are created by the difference between
two events. Each page of the ring buffer holds a full 64 bit timestamp.
Each event has a 27 bit delta stamp from the last event. The unit of time
is nanoseconds, so 27 bits can hold ~134 milliseconds. If two events
happen more than 134 milliseconds apart, a time extend is inserted
to add more bits for the delta. The time extend has 59 bits, which
is good for ~18 years.
Currently the time extend is committed separately from the event.
If an event is discarded before it is committed, due to filtering,
the time extend still exists. If all events are being filtered, then
after ~134 milliseconds a new time extend will be added to the buffer.
This can only happen till the end of the page. Since each page holds
a full timestamp, there is no reason to add a time extend to the
beginning of a page. Time extends can only fill a page that has actual
data at the beginning, so there is no fear that time extends will fill
more than a page without any data.
When reading an event, a loop is made to skip over time extends
since they are only used to maintain the time stamp and are never
given to the caller. As a paranoid check to prevent the loop running
forever, with the knowledge that time extends may only fill a page,
a check is made that tests the iteration of the loop, and if the
iteration is more than the number of time extends that can fit in a page
a warning is printed and the ring buffer is disabled (all of ftrace
is also disabled with it).
There is another event type that is called a TIMESTAMP which can
hold 64 bits of data in the theoretical case that two events happen
18 years apart. This code has not been implemented, but the name
of this event exists, as well as the structure for it. The
size of a TIMESTAMP is 16 bytes, where as a time extend is only
8 bytes. The macro used to calculate how many time extends can fit on
a page used the TIMESTAMP size instead of the time extend size
cutting the amount in half.
The following test case can easily trigger the warning since we only
need to have half the page filled with time extends to trigger the
warning:
Enabling the function tracer and then setting the filter to only trace
functions where the process id is negative (no events), then clearing
the trace buffer to ensure that we have nothing in the buffer,
then write to trace_marker to add an event to the beginning of a page,
sleep for 2 minutes (only 35 seconds is probably needed, but this
guarantees the bug), and then finally reading the trace which will
trigger the bug.
This patch fixes the typo and prevents the false positive of that warning.
Reported-by: Hans J. Koch <hjk@linutronix.de> Tested-by: Hans J. Koch <hjk@linutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit f81f2f7c (ubd: drop unnecessary rq->sector manipulation)
dropped request->sector manipulation in preparation for global request
handling cleanup; unfortunately, it incorrectly assumed that the
updated sector wasn't being used.
ubd tries to issue as many requests as possible to io_thread. When
issuing fails due to memory pressure or other reasons, the device is
put on the restart list and issuing stops. On IO completion, devices
on the restart list are scanned and IO issuing is restarted.
ubd issues IOs sg-by-sg and issuing can be stopped in the middle of a
request, so each device on the restart queue needs to remember where
to restart in its current request. ubd needs to keep track of the
issue position itself because,
* blk_rq_pos(req) is now updated by the block layer to keep track of
_completion_ position.
* Multiple io_req's for the current request may be in flight, so it's
difficult to tell where blk_rq_pos(req) currently is.
Add ubd->rq_pos to keep track of the issue position and use it to
correctly restart io_req issue.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Richard Weinberger <richard@nod.at> Tested-by: Richard Weinberger <richard@nod.at> Tested-by: Chris Frey <cdfrey@foursquare.net> Signed-off-by: Jens Axboe <jaxboe@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
free_irq_cfg() is not freeing the cpumask_vars in irq_cfg. Fixing this
triggers a use after free caused by the fact that copying struct
irq_cfg is done with memcpy, which copies the pointer not the cpumask.
Fix both places.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Yinghai Lu <yhlu.kernel@gmail.com>
LKML-Reference: <alpine.LFD.2.00.1009282052570.2416@localhost6.localdomain6> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed JSIOCSAXMAP ioctl to update absmap, the map from hardware axis to
event axis in addition to abspam. This fixes a regression introduced
by 999b874f.
The compat code for the VIDIOCSMICROCODE ioctl is totally buggered.
It's only used by the VIDEO_STRADIS driver, and that one is scheduled to
staging and eventually removed unless somebody steps up to maintain it
(at which point it should use request_firmware() rather than some magic
ioctl). So we'll get rid of it eventually.
But in the meantime, the compatibility ioctl code is broken, and this
tries to get it to at least limp along (even if Mauro suggested just
deleting it entirely, which may be the right thing to do - I don't think
the compatibility translation code has ever worked unless you were very
lucky).
The guest can use the paravirt clock in kvmclock.c which is used
by sched_clock(), which in turn is used by the tracing mechanism
for timestamps, which leads to infinite recursion.
Disable mcount/tracing for kvmclock.o.
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Avi Kivity <avi@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using a paravirt clock, pvclock.c can be used by sched_clock(),
which in turn is used by the tracing mechanism for timestamps,
which leads to infinite recursion.
Disable mcount/tracing for pvclock.o.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
LKML-Reference: <4C9A9A3F.4040201@goop.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a workaround for an IOMMU BIOS problem to
the AMD IOMMU driver. The result of the bug is that the
IOMMU does not execute commands anymore when the system
comes out of the S3 state resulting in system failure. The
bug in the BIOS is that is does not restore certain hardware
specific registers correctly. This workaround reads out the
contents of these registers at boot time and restores them
on resume from S3. The workaround is limited to the specific
IOMMU chipset where this problem occurs.
In the __unmap_single function the dma_addr is rounded down
to a page boundary before the dma pages are unmapped. The
address is later also used to flush the TLB entries for that
mapping. But without the offset into the dma page the amount
of pages to flush might be miscalculated in the TLB flushing
path. This patch fixes this bug by using the original
address to flush the TLB.
This patch moves the setting of the configuration and
feature flags out out the acpi table parsing path and moves
it into the iommu-enable path. This is needed to reliably
fix resume-from-s3.
If not all clocks have been defined in platform data, the driver will
cause a null pointer dereference when it is removed. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The HW by default has RX coalescing on. For iWARP connections, this
causes a 100ms delay in connection establishement due to the ingress
MPA Start message being stalled in HW. So explicitly turn RX
coalescing off when setting up iWARP connections.
This was causing very bad performance for NP64 gather operations using
Open MPI, due to the way it sets up connections on larger jobs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 46034dca515bc4ddca0399ae58106d1f5f0d809f (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For shared fifo hw endpoint(with FIFO_TXRX style), only ep_in
field of musb_hw_ep is intialized in musb_g_init_endpoints, and
ep_out is not initialized, but musb_g_rx and rxstate may access
ep_out field of musb_hw_ep by the method below:
musb_ep = &musb->endpoints[epnum].ep_out
which can cause the kernel panic[1] below, this patch fixes the issue
by getting 'musb_ep' from '&musb->endpoints[epnum].ep_in' for shared fifo
endpoint.
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes in the usbhid layer exposed a bug in usbcore. If
CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned
a minor number of 0. However interfaces that aren't registered as USB
class devices also have their minor number set to 0, during
initialization. As a result usb_find_interface() may return the
wrong interface, leading to a crash.
This patch (as1418) fixes the problem by initializing every
interface's minor number to -1. It also cleans up the
usb_register_dev() function, which besides being somewhat awkwardly
written, does not unwind completely on all its error paths.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Philip J. Turmel <philip@turmel.org> Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com> Tested-by: Alex Riesen <raa.lkml@gmail.com> Tested-by: Matthias Bayer <jackdachef@gmail.com> CC: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver module is unloaded and the last still open file is a raw
MIDI device, the card and its devices will be actually freed in the
snd_card_file_remove() call when that file is closed. Afterwards, rmidi
and rmidi->card point into freed memory, so the module pointer is likely
to be garbage.
(This was introduced by commit 9a1b64caac82aa02cb74587ffc798e6f42c6170a.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-by: Krzysztof Foltman <wdev@foltman.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The snd_ctl_new() function in sound/core/control.c allocates space for a
snd_kcontrol struct by performing arithmetic operations on a
user-provided size without checking for integer overflow. If a user
provides a large enough size, an overflow will occur, the allocated
chunk will be too small, and a second user-influenced value will be
written repeatedly past the bounds of this chunk. This code is
reachable by unprivileged users who have permission to open
a /dev/snd/controlC* device (on many distros, this is group "audio") via
the SNDRV_CTL_IOCTL_ELEM_ADD and SNDRV_CTL_IOCTL_ELEM_REPLACE ioctls.
On the HT-Omega Claro halo card, the ADC data must be captured from the
second I2S input. Using the default first input, which isn't connected
to anything, would result in silence.
Signed-off-by: Erik J. Staab <ejs@insightbb.com> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SNDRV_HDSP_IOCTL_GET_CONFIG_INFO and
SNDRV_HDSP_IOCTL_GET_CONFIG_INFO ioctls in hdspm.c and hdsp.c allow
unprivileged users to read uninitialized kernel stack memory, because
several fields of the hdsp{m}_config_info structs declared on the stack
are not altered or zeroed before being copied back to the user. This
patch takes care of it.
James Dingwall [Mon, 27 Sep 2010 08:37:17 +0000 (09:37 +0100)]
Xen: fix typo in previous patch
Correctly name the irq_chip structure to fix an immediate failure when booting
as a xen pv_ops guest with a NULL pointer exception. The missing 'x' was
introduced in commit [fb412a178502dc498430723b082a932f797e4763] applied to
2.6.3[25]-stable trees. The commit to mainline was
[aaca49642b92c8a57d3ca5029a5a94019c7af69f] which did not have the problem.
[ Backport to .32 by Tomáš Janoušek <tomi@nomi.cz> ]
xchg() and cmpxchg() modify their memory operands, not merely read
them. For some versions of gcc the "memory" clobber has apparently
dealt with the situation, but not for all.
Originally-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Glauber Costa <glommer@redhat.com> Cc: Avi Kivity <avi@redhat.com> Cc: Peter Palfrader <peter@palfrader.org> Cc: Greg KH <gregkh@suse.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Zachary Amsden <zamsden@redhat.com> Cc: Marcelo Tosatti <mtosatti@redhat.com>
LKML-Reference: <4C4F7277.8050306@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When compiling alpha generic build get errors such as:
arch/alpha/kernel/err_marvel.c: In function ‘marvel_print_err_cyc’:
arch/alpha/kernel/err_marvel.c:119: error: format ‘%ld’ expects type ‘long int’, but argument 6 has type ‘u64’
Replaced a number of %ld format specifiers with %lld since u64
is unsigned long long.
Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SIS 760 is listed in the device tables for both amd64-agp and sis-agp.
amd64-agp is apparently preferable since it has workarounds for some
BIOS misconfigurations that sis-agp doesn't handle.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Monday 04 January 2010 02:30:24 pm Russell King wrote:
> Found the problem - getting rid of the read of the alt status register
> after the command has been written fixes the UDMA CRC errors on write:
>
> @@ -676,7 +676,8 @@ void ata_sff_exec_command(struct ata_port *ap, const struct
> ata_taskfile *tf)
> DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
>
> iowrite8(tf->command, ap->ioaddr.command_addr);
> - ata_sff_pause(ap);
> + ndelay(400);
> +// ata_sff_pause(ap);
> }
> EXPORT_SYMBOL_GPL(ata_sff_exec_command);
>
>
> This rather makes sense. The PDC20247 handles the UDMA part of the
> protocol. It has no way to tell the PDC20246 to wait while it suspends
> UDMA, so that a normal register access can take place - the 246 ploughs
> on with the register access without any regard to the state of the 247.
>
> If the drive immediately starts the UDMA protocol after a write to the
> command register (as it probably will for the DMA WRITE command), then
> we'll be accessing the taskfile in the middle of the UDMA setup, which
> can't be good. It's certainly a violation of the ATA specs.
Fix it by adding custom ->sff_exec_command method for UDMA33 chipsets.
Debugged-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several MIPS platforms don't set pci_controller::io_map_base for their
PCI bridges. This results in a panic in pci_iomap(). (The panic is
conditional on CONFIG_PCI_DOMAINS, but that is now enabled for all PCI
MIPS systems.)
Input core displays capabilities bitmasks in form of one or more longs printed
in hex form and separated by spaces. Unfortunately it does not work well
for 32-bit applications running on 64-bit kernels since applications expect
that number is "worth" only 32 bits when kernel advances by 64 bits.
Fix that by ensuring that output produced for compat tasks uses 32-bit units.
"hostap: Protect against initialization interrupt" (which reinstated
"wireless: hostap, fix oops due to early probing interrupt")
reintroduced Bug 16111. This is because hostap_pci wasn't setting
dev->base_addr, which is now checked in prism2_interrupt. As a result,
initialization was failing for PCI-based hostap devices. This corrects
that oversight.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When GRO produces fraglist entries, and the resulting skb hits
an interface that is incapable of TSO but capable of FRAGLIST,
we end up producing a bogus packet with gso_size non-zero.
This was reported in the field with older versions of KVM that
did not set the TSO bits on tuntap.
This patch fixes that.
Reported-by: Igor Zhang <yugzhang@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 98962465ed9e6ea99c38e0af63fe1dcb5a79dc25 ("nohz: Prevent
clocksource wrapping during idle"), the CPU of an R2D board never goes
to idle. This commit assumes that mult and shift are assigned before
the clocksource is registered. As a consequence the safe maximum sleep
time is negative and the CPU never goes into idle.
This patch fixes the problem by moving mult and shift initialization
from sh_tmu_clocksource_enable() to sh_tmu_register_clocksource().
Partition boundary calculation fails for DASD FBA disks under the
following conditions:
- disk is formatted with CMS FORMAT with a blocksize of more than
512 bytes
- all of the disk is reserved to a single CMS file using CMS RESERVE
- the disk is accessed using the DIAG mode of the DASD driver
Under these circumstances, the partition detection code tries to
read the CMS label block containing partition-relevant information
from logical block offset 1, while it is in fact located at physical
block offset 1.
Fix this problem by using the correct CMS label block location
depending on the device type as determined by the DASD SENSE ID
information.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[bwh: Adjust for 2.6.32] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting new MAC address only worked when device was set to promiscuous mode.
Fix MAC address by writing new address to device using undocumented command
AX_CMD_READ_NODE_ID+1. Patch is tested with AX88772 device.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Hollis <dhollis@davehollis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver attempts to select an IRQ for the NIC automatically by
testing which of the supported IRQs are available and then probing
each available IRQ with probe_irq_{on,off}(). There are obvious race
conditions here, besides which:
1. The test for availability is done by passing a NULL handler, which
now always returns -EINVAL, thus the device cannot be opened:
<http://bugs.debian.org/566522>
2. probe_irq_off() will report only the first ISA IRQ handled,
potentially leading to a false negative.
There was another bug that meant it ignored all error codes from
request_irq() except -EBUSY, so it would 'succeed' despite this
(possibly causing conflicts with other ISA devices). This was fixed
by ab08999d6029bb2c79c16be5405d63d2bedbdfea 'WARNING: some
request_irq() failures ignored in el2_open()', which exposed bug 1.
This patch:
1. Replaces the use of probe_irq_{on,off}() with a real interrupt handler
2. Adds a delay before checking the interrupt-seen flag
3. Disables interrupts on all failure paths
4. Distinguishes error codes from the second request_irq() call,
consistently with the first
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log