Mark Brown [Wed, 15 Jul 2009 12:03:34 +0000 (13:03 +0100)]
S3C64XX: Fix get_rate() for ARMCLK
If the requested clock is faster than the parent clock then the
parent clock is the closest we can get to the request so we need
to return that instead of the requested clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
S3C24XX: GPIO: Fix pin range check in s3c_gpiolib_getchip
In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is
in the gpio banks range is reversed. Thus the function returns NULL for valid
pins and the gpio chip if its not valid.
As a result gpio states are not saved/restored properly during suspend/resume.
kmemleak: Protect the seq start/next/stop sequence by rcu_read_lock()
Objects passed to kmemleak_seq_next() have an incremented reference
count (hence not freed) but they may point via object_list.next to
other freed objects. To avoid this, the whole start/next/stop sequence
must be protected by rcu_read_lock().
Merge branch 'drm-radeon-kms' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-radeon-kms' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon: set fb aperture sizes for framebuffer handoff.
drm/ttm: fix highuser vs dma32 confusion.
drm/radeon: Fix size used for benchmarking BO copies.
drm/radeon: Add radeon.test parameter for running BO GPU copy tests.
drm/radeon/kms: allow interruptible waits for objects.
drm/ttm: powerpc: Fix Highmem cache flushing.
x86: Export kmap_atomic_prot() needed for TTM.
drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes.
drm/ttm: Fix an oops and sync object leak.
drm/radeon/kms: vram sizing on certain r100 chips needs workaround.
drm/radeon: Pay more attention to object placement requested by userspace.
drm/radeon: Fall back to evicting BOs with memcpy if necessary.
drm/radeon: Don't unreserve twice on failure to validate.
drm/radeon/kms: fix bandwidth computation on avivo hardware
drm/radeon/kms: add initial colortiling support.
drm/radeon/kms: fix hotspot handling on pre-avivo chips
drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740
drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq
drm/radeon/kms: block RN50 from using 3D engine.
drm/radeon/kms: fix VRAM sizing like DDX does it.
...
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: accept late unlocking of HPA
libata: Updates and fixes for pata_at91 driver
ata_piix: Add new short cable ID
ata_piix: Add new laptop short cable IDs
ahci: add device IDs for Ibex Peak ahci controllers
libata: remove superfluous NULL pointer checks
libata: add missing NULL pointer check to ata_eh_reset()
pata_pcmcia: add CNF-CDROM-ID
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: documentation: make it clear that sysfs is optional
driver core: sysdev: do not send KOBJ_ADD uevent if kobject_init_and_add fails
Dynamic debug: fix typo: -/->
driver core: firmware_class:fix memory leak of page pointers array
sysfs: fix hardlink count on device_move
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: udlfb: Add vmalloc.h include
staging: remove aten2011 driver
Staging: android: lowmemorykiller.c: fix it for "oom: move oom_adj value from task_struct to mm_struct"
Staging: serqt_usb2: fix memory leak in error case
Staging: serqt_usb2: add missing calls to tty_kref_put()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (34 commits)
USB: xhci: Stall handling bug fixes.
USB: xhci: Support for 64-byte contexts
USB: xhci: Always align output device contexts to 64 bytes.
USB: xhci: Scratchpad buffer allocation
USB: Fix parsing of SuperSpeed Endpoint Companion descriptor.
USB: xhci: Fail gracefully if there's no SS ep companion descriptor.
USB: xhci: Handle babble errors on transfers.
USB: xhci: Setup HW retries correctly.
USB: xhci: Check if the host controller died in IRQ handler.
USB: xhci: Don't oops if the host doesn't halt.
USB: xhci: Make debugging more verbose.
USB: xhci: Correct Event Handler Busy flag usage.
USB: xhci: Handle short control packets correctly.
USB: xhci: Represent 64-bit addresses with one u64.
USB: xhci: Use GFP_ATOMIC while holding spinlocks.
USB: xhci: Deal with stalled endpoints.
USB: xhci: Set TD size in transfer TRB.
USB: xhci: fix less- and greater than confusion
USB: usbtest: no need for USB_DEVICEFS
USB: musb: fix CONFIGDATA register read issue
...
We really don't want to mark the pty as a low-latency device, because as
Alan points out, the ->write method can be called from an IRQ (ppp?),
and that means we can't use ->low_latency=1 as we take mutexes in the
low_latency case.
So rather than using low_latency to force the written data to be pushed
to the ldisc handling at 'write()' time, just make the reader side (or
the poll function) do the flush when it checks whether there is data to
be had.
This also fixes the problem with lost data in an emacs compile buffer
(bugzilla 13815), and we can thus revert the low_latency pty hack
(commit 3a54297478e6578f96fd54bf4daa1751130aca86: "pty: quickfix for the
pty ENXIO timing problems").
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[ Modified to do the tty_flush_to_ldisc() inside input_available_p() so
that it triggers for both read and poll() - Linus] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Hellstrom [Fri, 24 Jul 2009 07:57:33 +0000 (09:57 +0200)]
x86: Export kmap_atomic_prot() needed for TTM.
This functionality is needed to kmap_atomic() highmem pages that may
potentially have or are about to set up other mappings with
non-standard caching attributes.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Fri, 24 Jul 2009 07:57:34 +0000 (09:57 +0200)]
drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes.
For x86 this affected highmem pages only, since they were always kmapped
cache-coherent, and this is fixed using kmap_atomic_prot().
For other architectures that may not modify the linear kernel map we
resort to vmap() for now, since kmap_atomic_prot() generally uses the
linear kernel map for lowmem pages. This of course comes with a
performance impact and should be optimized when possible.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 21 Jul 2009 10:39:30 +0000 (20:39 +1000)]
drm/radeon/kms: vram sizing on certain r100 chips needs workaround.
If an rn50/r100/m6/m7 GPU has < 64MB RAM, i.e. 8/16/32, the
aperture used to calculate the MC_FB_LOCATION needs to be worked
out from the CONFIG_APER_SIZE register, and not the actual vram size.
TTM VRAM size was also being initialised wrong, use actual vram size
to initialise it.
Dave Airlie [Tue, 23 Jun 2009 23:48:08 +0000 (09:48 +1000)]
drm/radeon/kms: add initial colortiling support.
This adds new set/get tiling interfaces where the pitch
and macro/micro tiling enables can be set. Along with
a flag to decide if this object should have a surface when mapped.
The only thing we need to allocate with a mapped surface should be
the frontbuffer. Note rotate scanout shouldn't require one, and
back/depth shouldn't either, though mesa needs some fixes.
It fixes the TTM interfaces along Thomas's suggestions, and I've tested
the surface stealing code with two X servers and not seen any lockdep issues.
I've stopped tiling the fbcon frontbuffer, as I don't see there being
any advantage other than testing, I've left the testing commands in there,
just flip the fb_tiled to true in radeon_fb.c
Open: Can we integrate endian swapping in with this?
Future features:
texture tiling - need to relocate texture registers TXOFFSET* with tiling info.
This also merges Michel's cleanup surfaces regs at init time patch
even though it makes sense on its own, this patch really relies on it.
Some PowerMac firmwares set up a tiling surface at the beginning of VRAM
which messes us up otherwise.
that patch is: Signed-off-by: Michel Dänzer <daenzer@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
On certain configurations, HPA isn't or can't be unlocked during
probing but it somehow ends up unlocked afterwards. In the following
thread, the problem can be reliably reproduced after resuming from
STR. The BIOS turns on HPA during boot but forgets to do it during
resume.
http://thread.gmane.org/gmane.linux.kernel/858310
This patch updates libata revalidation such that it considers native
n_sectors. If the device size has increased to match native
n_sectors, it's assumed that HPA has been unlocked involuntarily and
the device is recognized as the same one. This should be fairly safe
while nicely working around the problem.
Please consider the following updates and fixes for pata_at91 driver.
* Removed extra headers
Here we need only static memory controller properties, which are
contained in generic header at91sam9_smc.h.
No need to include any specific headers for at91sam9260 SoC.
* No harsh BUG_ON for get_clk in set_smc_timing function
get_clk is now performed in driver probing function,
probing fails if master clock is not available
* Fixed uint/ulong mess in calc_mck_cycles function
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Steve Conklin [Thu, 16 Jul 2009 21:27:56 +0000 (16:27 -0500)]
ata_piix: Add new laptop short cable IDs
OriginalAuthor: Michael Frey <michael.frey@canonical.com> Signed-off-by: Steve Conklin <sconklin@canonical.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata: add missing NULL pointer check to ata_eh_reset()
drivers/ata/libata-eh.c +2403 ata_eh_reset(80) warning: variable derefenced before check 'slave'
Please note that this is _not_ a real bug at the moment since ata_eh_context
structure is embedded into ata_list structure and the code alwas checks for
'slave' before accessing 'sehc'.
Anyway lets add missing check and always have a valid 'sehc' pointer (which
makes code easier to understand and prevents introducing some possible bugs
in the future).
Reported-by: Dan Carpenter <error27@gmail.com> Cc: corbet@lwn.net Cc: eteo@redhat.com Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sarah Sharp [Mon, 27 Jul 2009 19:05:21 +0000 (12:05 -0700)]
USB: xhci: Stall handling bug fixes.
Correct the xHCI code to handle stalls on USB endpoints. We need to move
the endpoint ring's dequeue pointer past the stalled transfer, or the HW
will try to restart the transfer the next time the doorbell is rung.
Don't attempt to clear a halt on an endpoint if we haven't seen a stalled
transfer for it. The USB core will attempt to clear a halt on all
endpoints when it selects a new configuration.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
John Youn [Mon, 27 Jul 2009 19:05:15 +0000 (12:05 -0700)]
USB: xhci: Support for 64-byte contexts
Adds support for controllers that use 64-byte contexts. The following context
data structures are affected by this: Device, Input, Input Control, Endpoint,
and Slot. To accommodate the use of either 32 or 64-byte contexts, a Device or
Input context can only be accessed through functions which look-up and return
pointers to their contained contexts.
Signed-off-by: John Youn <johnyoun@synopsys.com> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:05:08 +0000 (12:05 -0700)]
USB: xhci: Always align output device contexts to 64 bytes.
Make sure the xHCI output device context is 64-byte aligned. Previous
code was using the same structure for both the output device context and
the input control context. Since the structure had 32 bytes of flags
before the device context, the output device context wouldn't be 64-byte
aligned. Define a new structure to use for the output device context and
clean up the debugging for these two structures.
The copy of the device context in the input control context does *not*
need to be 64-byte aligned.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
John Youn [Mon, 27 Jul 2009 19:05:03 +0000 (12:05 -0700)]
USB: xhci: Scratchpad buffer allocation
Allocates and initializes the scratchpad buffer array (XHCI 4.20). This is an
array of 64-bit DMA addresses to scratch pages that the controller may use
during operation. The number of pages is specified in the "Max Scratchpad
Buffers" field of HCSPARAMS2. The DMA address of this array is written into
slot 0 of the DCBAA.
Signed-off-by: John Youn <johnyoun@synopsys.com> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:04:52 +0000 (12:04 -0700)]
USB: Fix parsing of SuperSpeed Endpoint Companion descriptor.
usb_parse_ss_endpoint_companion() was supposed to allocate a structure to
hold the SuperSpeed Endpoint Companion descriptor, and either copy the
values the device returned, or fill in default values if the device
descriptor did not include the companion descriptor.
However, the previous code would miss the last endpoint in a configuration
with no descriptors after it. Make usb_parse_endpoint() allocate the SS
endpoint companion descriptor and fill it with default values, even if
we've run out of buffer space in this configuration descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:04:38 +0000 (12:04 -0700)]
USB: xhci: Fail gracefully if there's no SS ep companion descriptor.
This is a work around for a bug in the SuperSpeed Endpoint Companion Descriptor
parsing code. It fails in some corner cases, which means ep->ss_ep_comp may be
NULL.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:04:27 +0000 (12:04 -0700)]
USB: xhci: Setup HW retries correctly.
The xHCI host controller can be programmed to retry a transfer a certain number
of times per endpoint before it passes back an error condition to the host
controller driver. The xHC will return an error code when the error count
transitions from 1 to 0. Programming an error count of 3 means the xHC tries
the transfer 3 times, programming it with a 1 means it tries to transfer once,
and programming it with 0 means the HW tries the transfer infinitely.
We want isochronous transfers to only be tried once, so set the error count to
one.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:03:40 +0000 (12:03 -0700)]
USB: xhci: Correct Event Handler Busy flag usage.
The Event Handler Busy bit in the event ring dequeue pointer is write 1 to
clear. Fix the interrupt service routine to clear that bit after the
event handler has run.
xhci_set_hc_event_deq() is designed to update the event ring dequeue pointer
without changing any of the four reserved bits in the lower nibble. The event
handler busy (EHB) bit is write one to clear, so the new value must always
contain a zero in that bit in order to preserve the EHB value.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:03:36 +0000 (12:03 -0700)]
USB: xhci: Handle short control packets correctly.
When there is a short packet on a control transfer, the xHCI host controller
hardware will generate two events. The first event will be for the data stage
TD with a completion code for a short packet. The second event will be for the
status stage with a successful completion code. Before this patch, the xHCI
driver would giveback the short control URB when it received the event for the
data stage TD. Then it would become confused when it saw a status stage event
for the endpoint for an URB it had already finished processing.
Change the xHCI host controller driver to wait for the status stage event when
it receives a short transfer completion code for a data stage TD.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:03:31 +0000 (12:03 -0700)]
USB: xhci: Represent 64-bit addresses with one u64.
There are several xHCI data structures that use two 32-bit fields to
represent a 64-bit address. Since some architectures don't support 64-bit
PCI writes, the fields need to be written in two 32-bit writes. The xHCI
specification says that if a platform is incapable of generating 64-bit
writes, software must write the low 32-bits first, then the high 32-bits.
Hardware that supports 64-bit addressing will wait for the high 32-bit
write before reading the revised value, and hardware that only supports
32-bit writes will ignore the high 32-bit write.
Previous xHCI code represented 64-bit addresses with two u32 values. This
lead to buggy code that would write the 32-bits in the wrong order, or
forget to write the upper 32-bits. Change the two u32s to one u64 and
create a function call to write all 64-bit addresses in the proper order.
This new function could be modified in the future if all platforms support
64-bit writes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:03:23 +0000 (12:03 -0700)]
USB: xhci: Use GFP_ATOMIC while holding spinlocks.
The xHCI functions to queue an URB onto the hardware rings must be called
with the xhci spinlock held. Those functions will allocate memory, and
take a gfp_t memory flags argument. We must pass them the GFP_ATOMIC
flag, since we don't want the memory allocation to attempt to sleep while
waiting for more memory to become available.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:03:15 +0000 (12:03 -0700)]
USB: xhci: Deal with stalled endpoints.
When an endpoint on a device under an xHCI host controller stalls, the
host controller driver must let the hardware know that the USB core has
successfully cleared the halt condition. The HCD submits a Reset Endpoint
Command, which will clear the toggle bit for USB 2.0 devices, and set the
sequence number to zero for USB 3.0 devices.
The xHCI urb_enqueue will accept new URBs while the endpoint is halted,
and will queue them to the hardware rings. However, the endpoint doorbell
will not be rung until the Reset Endpoint Command completes.
Don't queue a reset endpoint command for root hubs. khubd clears halt
conditions on the roothub during the initialization process, but the roothub
isn't a real device, so the xHCI host controller doesn't need to know about the
cleared halt.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 27 Jul 2009 19:03:07 +0000 (12:03 -0700)]
USB: xhci: Set TD size in transfer TRB.
The 0.95 xHCI specification requires software to set the "TD size" field
in each transaction request block (TRB). This field gives the host
controller an indication of how much data is remaining in the TD
(including the buffer in the current TRB). Set this field in bulk TRBs
and data stage TRBs for control transfers.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 28 Jul 2009 15:56:17 +0000 (11:56 -0400)]
USB: usbtest: no need for USB_DEVICEFS
THis patch (as1270) allows the usbtest module to be built even when
USB_DEVICEFS isn't configured. Tests can be performed without
USB_DEVICEFS, using the /dev/bus/usb/*/* device files.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
INDEX register has to be set to '0' before reading
CONFIGDATA register which is only present in TI musb
platforms.
Currently the default register access mode is set to
FLAT_MODE thus INDEX register is not getting set
properly with musb_ep_select() which is just a nop
operation in FLAT_MODE.This invalid register read is
causing module reinset failure.
Fixing the issue by moving INDEX register write part to
musb_read_configdata() function itself.
Sergei Shtylyov [Fri, 17 Jul 2009 14:30:03 +0000 (17:30 +0300)]
USB: musb_gadget_ep0: fix typo in service_zero_data_request()
This function uses wrong bit mask to prevent clearing RXCSR status
bits when halting an endpoint -- which results in clearing SentStall
and RxPktRdy bits (that the code actually tries to avoid); must be
a result of cut-and-paste...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Javier Martin [Thu, 23 Jul 2009 02:03:43 +0000 (04:03 +0200)]
USB: option.c to support Alcatel X060S/X200 broadband modems
Added support for the Alcatel X060S/X200 broadband modems to the option
driver. The device starts in cd-rom emulation mode (1bbb:f000) and
requires the use of the usb_modeswitch tool to switch it to modem mode
(1bbb:0000).
Signed-off-by: Javier Martin <jmartinj@iname.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Russell Lang [Fri, 17 Jul 2009 09:29:20 +0000 (19:29 +1000)]
USB: aten uc2324 is really a moschip 7840
I've opened up the case, and the chips in the ATEN UC2324 are:
Moschip
MCS7840CV-AA
69507-6B1
0650
(USB to 4-port serial)
(logo with AF kerned together) 0748
24BC02
SINGLP
(unknown 8-pin chip)
(logo looks like 3 or Z in circle)
ZT3243LEEA 0752 B7A16420.T
(4 chips, so this will be RS232 line driver)
(Probably equivalent of Sipex SP3243)
So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840,
and should use the mos7840.c driver. I expect you will remove the
aten2011.c driver from the staging area.
From the aten2011.c source code, the device ID for the UC2322 (2 port
serial) is 0x7820, just like the Moschip evaluation board. This value
should be added to the device id table of mos7840.c.
Here's a patch that adds these devices to the driver.
From: Russell Lang <gsview@ghostgum.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: option: add ZTE device ids and remove ONDA ids
Current listed Onda ids are ZTE devices. Replace them with ZTE id define
and add more ZTE device ids. Also remove 19d2:2000, this is the id when
device is first plugged in and is a CD-only device, before the switch
using eject.
These changes are based on a previous patch by Ming Zhao
<zhao.ming9@zte.com.cn>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Cc: Ming Zhao <zhao.ming9@zte.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Kagstrom [Mon, 13 Jul 2009 06:25:09 +0000 (08:25 +0200)]
USB: ehci-orion: Call ehci_reset before ehci_halt
I noticed that USB initialization didn't setup correctly on my kirkwood
based board (OpenRD base) if I hadn't initialized USB in U-boot first.
The error message looks like this:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: can't setup
orion-ehci orion-ehci.0: USB bus 1 deregistered
orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110
orion-ehci: probe of orion-ehci.0 failed with error -110
which is caused by ehci_halt() timing out in the handshake() call. I
noticed that U-boot does a reset before calling handshake(), so this
patch does the same thing for Linux. USB now works for me.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: OMAP: OHCI: hc_driver's stop method should call ohci_stop
OMAP: OHCI: hc_driver's stop method should call ohci_stop
Without this, the ohci-omap driver will not cleanup the debugfs
nodes when the driver is unloaded. So the next insmod will fail,
if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected.
USB: storage: raise timeout in usb_stor_Bulk_max_lun
Requests to get max LUN, for certain USB storage devices, require a
longer timeout before a correct reply is returned. This happens for a
Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set
to 0, thus losing functionality, because of the timeout occurring too
quickly.
Raising the timeout value fixes the issue and might help other devices
to return a correct max LUN value as well.
Carlos R. Mafra [Mon, 13 Jul 2009 19:45:03 +0000 (21:45 +0200)]
USB: option: Remove unused variable
After commit f092c240494f2d807401d93f95f683909b90af96 ("USB: option:
remove unnecessary and erroneous code") the variable 'serial' becomes
unused, as gcc-4.3.2 points out:
drivers/usb/serial/option.c: In function 'option_instat_callback':
drivers/usb/serial/option.c:834: warning: unused variable 'serial'
drivers/usb/serial/option.c: In function 'option_open':
drivers/usb/serial/option.c:930: warning: unused variable 'serial'
So I removed it.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (22 commits)
Btrfs: Fix async caching interaction with unmount
Btrfs: change how we unpin extents
Btrfs: Correct redundant test in add_inode_ref
Btrfs: find smallest available device extent during chunk allocation
Btrfs: clear all space_info->full after removing a block group
Btrfs: make flushoncommit mount option correctly wait on ordered_extents
Btrfs: Avoid delayed reference update looping
Btrfs: Fix ordering of key field checks in btrfs_previous_item
Btrfs: find_free_dev_extent doesn't handle holes at the start of the device
Btrfs: Remove code duplication in comp_keys
Btrfs: async block group caching
Btrfs: use hybrid extents+bitmap rb tree for free space
Btrfs: Fix crash on read failures at mount
Btrfs: remove of redundant btrfs_header_level
Btrfs: adjust NULL test
Btrfs: Remove broken sanity check from btrfs_rmap_block()
Btrfs: convert nested spin_lock_irqsave to spin_lock
Btrfs: make sure all dirty blocks are written at commit time
Btrfs: fix locking issue in btrfs_find_next_key
Btrfs: fix double increment of path->slots[0] in btrfs_next_leaf
...
eCryptfs: parse_tag_3_packet check tag 3 packet encrypted key size
The parse_tag_3_packet function does not check if the tag 3 packet contains a
encrypted key size larger than ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES.
Signed-off-by: Ramon de Carvalho Valle <ramon@risesecurity.org>
[tyhicks@linux.vnet.ibm.com: Added printk newline and changed goto to out_free] Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com> Cc: stable@kernel.org (2.6.27 and 30) Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tag 11 packets are stored in the metadata section of an eCryptfs file to
store the key signature(s) used to encrypt the file encryption key.
After extracting the packet length field to determine the key signature
length, a check is not performed to see if the length would exceed the
key signature buffer size that was passed into parse_tag_11_packet().
Thanks to Ramon de Carvalho Valle for finding this bug using fsfuzzer.
David Rientjes [Tue, 16 Jun 2009 23:42:53 +0000 (16:42 -0700)]
Staging: android: lowmemorykiller.c: fix it for "oom: move oom_adj value from task_struct to mm_struct"
I'm about to merge "oom: move oom_adj value from task_struct to
mm_struct", and this fixup is needed to repair linux-next's
drivers/staging/android/lowmemorykiller.c.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ming Lei [Sat, 11 Jul 2009 03:11:10 +0000 (11:11 +0800)]
driver core: firmware_class:fix memory leak of page pointers array
The page pointers array is allocated in fw_realloc_buffer() called by
firmware_data_write(), and should be freed in release function of firmware
device.
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reported-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update directory hardlink count when moving kobjects to a new parent.
Fixes the following problem which occurs when several devices are
moved to the same parent and then unregistered:
I've tested TSL2550 driver and I've found a bug: when light is off,
returned value from tsl2550_calculate_lux function is -1 when it should
be 0 (sensor correctly read that light was off).
I think the bug is that a zero c0 value (approximated value of ch0) is
misinterpreted as an error.
Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com> Acked-by: Rodolfo Giometti <giometti@linux.it> Signed-off-by: Jean Delvare <khali@linux-fr.org>
On newer Asus boards the "upper" limit of a sensor is encoded as
delta from the "lower" limit. Fix the driver to correctly handle
this case.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com> Tested-by: Alex Macfarlane Smith <nospam@archifishal.co.uk> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Alan Cox [Mon, 27 Jul 2009 23:34:58 +0000 (00:34 +0100)]
usb_serial: Fix remaining ref count/lock bugs
This fixes
- locking bug that was hidden by ecc2e05e739c30870c8e4f252b63a0c4041f2724
- Regression #13821
- Spurious warning when closing and blocking for data write out
With these changes my PL2303 always ends up as ttyUSB0 when it should and
the module refcounts stay correct.
I'll do a more wholesale split & tidy of _open in the next release or two
as we get a standard tty_port_open and port->ops->init port->ops->shutdown
call backs.
Copy sent to Alan Stern and Carlos Mafra just to confirm it fixes all the
reports but it passes local testing with the same hardware as Alan Stern.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.infradead.org/users/eparis/notify
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: use GFP_NOFS under potential memory pressure
fsnotify: fix inotify tail drop check with path entries
inotify: check filename before dropping repeat events
fsnotify: use def_bool in kconfig instead of letting the user choose
inotify: fix error paths in inotify_update_watch
inotify: do not leak inode marks in inotify_add_watch
inotify: drop user watch count when a watch is removed
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
cnic: Fix ISCSI_KEVENT_IF_DOWN message handling.
net: irda: init spinlock after memcpy
ixgbe: fix for 82599 errata marking UDP checksum errors
r8169: WakeOnLan fix for the 8168
netxen: reset ring consumer during cleanup
net/bridge: use kobject_put to release kobject in br_add_if error path
smc91x.h: add config for Nomadik evaluation kit
NET: ROSE: Don't use static buffer.
eepro: Read buffer overflow
tokenring: Read buffer overflow
at1700: Read buffer overflow
fealnx: Write outside array bounds
ixgbe: remove unnecessary call to device_init_wakeup
ixgbe: Don't priority tag control frames in DCB mode
ixgbe: Enable FCoE offload when DCB is enabled for 82599
net: Rework mdio-ofgpio driver to use of_mdio infrastructure
register at91_ether using platform_driver_probe
skge: Enable WoL by default if supported
net: KS8851 needs to depend on MII
be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly.
...
Alan Cox [Mon, 27 Jul 2009 09:58:08 +0000 (10:58 +0100)]
tty: Fix a USB serial crash/scribble
The port lock is used to protect the port state. However the port structure
is freed on a hangup, then the lock taken on a close. The right fix is to
drop the port on tty->shutdown() but we can't yet do that due to sleep v
non-sleeping rules. Instead do the next best thing and fix it up when we are
not in -rc season.
Reported-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Alan Cox <alan@linux.intel.com> Tested-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Makefile cleanup
microblaze: Typo fix for cpu param inconsistency
microblaze: Add support for R_MICROBLAZE_64_NONE
microblaze: Get module loading working
microblaze: remove sys_ipc
microblaze: Support unaligned address for put/get_user macros
microblaze: Detect new Microblaze 7.20 versions
microblaze: Fix do_page_fault for no context
microblaze: Add _PAGE_FILE macros to pgtable.h
microblaze: Fix put_user macro for 64bits arguments
microblaze: Clear print messages for DTB passing via r7
microblaze: Not to clear r7 after copying DTB to kernel
microblaze: Add messages about FDT blob
microblaze: Final support for statically linked DTB
microblaze: remove duplicated #include
microblaze: Define tlb_flush macro
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: geode: Mark mfgpt irq IRQF_TIMER to prevent resume failure
x86, amd: Don't probe for extended APIC ID if APICs are disabled
x86, mce: Rename incorrect macro name "CONFIG_X86_THRESHOLD"
x86-64: Fix bad_srat() to clear all state
x86, mce: Fix set_trigger() accessor
x86: Fix movq immediate operand constraints in uaccess.h
x86: Fix movq immediate operand constraints in uaccess_64.h
x86: Add reboot fixup for SBC-fitPC2
x86: Include all of .data.* sections in _edata on 64-bit
x86: Add quirk for Intel DG45ID board to avoid low memory corruption
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix mute control with some ALC262 models
ALSA: snd_usb_caiaq: add support for Audio2DJ
ALSA: pcm - Fix hwptr buffer-size overlap bug
ALSA: pcm - Fix warnings in debug loggings
ALSA: pcm - Add logging of hwptr updates and interrupt updates
ASoC: tlv320aic3x: Enable PLL when not bypassed
ALSA: hda - Restore GPIO1 properly at resume with AD1984A
ALSA: ctxfi - Fix uninitialized error checks
ALSA: hda - Use snprintf() to be safer
ALSA: usb-audio - Volume control quirk for QuickCam E 3500
ALSA: pcm - Fix regressions with VMware
projects / linux-beck.git / log