Benoit Goby [Thu, 17 Oct 2013 17:48:46 +0000 (10:48 -0700)]
PM / Sleep: Detect device suspend/resume lockup and log event
Rather than hard-lock the kernel, dump the suspend/resume thread stack
and panic() to capture a message in pstore when a driver takes too long
to suspend/resume. Default suspend/resume watchdog timeout is set to 12
seconds to be longer than the usbhid 10 second timeout, but could be
changed at compile time.
Exclude from the watchdog the time spent waiting for children that
are resumed asynchronously and time every device, whether or not they
resumed synchronously.
This patch is targeted for mobile devices where a suspend/resume lockup
could cause a system reboot. Information about failing device can be
retrieved in subsequent boot session by mounting pstore and inspecting
the log. Laptops with EFI-enabled pstore could also benefit from
this feature.
The hardware watchdog timer is likely suspended during this time and
couldn't be relied upon. The soft-lockup detector would eventually tell
that tasks are not scheduled, but would provide little context as to why.
The patch hence uses system timer and assumes it is still active while the
devices are suspended/resumed.
This feature can be enabled/disabled during kernel configuration.
This change is based on earlier work by San Mehat.
Signed-off-by: Benoit Goby <benoit@android.com> Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jacob Pan [Thu, 17 Oct 2013 17:28:35 +0000 (10:28 -0700)]
PowerCap: Introduce Intel RAPL power capping driver
The Intel Running Average Power Limit (RAPL) technology provides platform
software with the ability to monitor, control, and get notifications on
power usage.
This feature is present in all Sandy Bridge and later Intel processors.
Newer models allow more fine grained controls to be applied. In RAPL,
power control is divided into domains, which include package, DRAM
controller, CPU core (Power Plane 0), graphics uncore (power plane 1), etc.
The purpose of this driver is to expose the RAPL settings to userspace.
Overall, RAPL fits in the new powercap class driver in that platform
level power capping controls are exposed via this generic interface.
This driver is based on an earlier patch from Zhang Rui.
However, while the previous work was mainly focused on thermal monitoring
the focus here is on the usability from user space perspective.
References: https://lkml.org/lkml/2011/5/26/93 Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq-next:
cpufreq: exynos4210: Use the common clock framework to set APLL clock rate
cpufreq: exynos4x12: Use the common clock framework to set APLL clock rate
cpufreq: Detect spurious invocations of update_policy_cpu()
cpufreq: pmac64: enable cpufreq on iMac G5 (iSight) model
cpufreq: pmac64: provide cpufreq transition latency for older G5 models
cpufreq: pmac64: speed up frequency switch
cpufreq: highbank-cpufreq: Enable Midway/ECX-2000
exynos-cpufreq: fix false return check from "regulator_set_voltage"
speedstep-centrino: Remove unnecessary braces
acpi-cpufreq: Add comment under ACPI_ADR_SPACE_SYSTEM_IO case
cpufreq: arm-big-little: use clk_get instead of clk_get_sys
cpufreq: exynos: Show a list of available frequencies
ACPI / PM: Drop two functions that are not used any more
Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.
Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaron Lu [Thu, 17 Oct 2013 13:38:53 +0000 (15:38 +0200)]
ATA / ACPI: remove power dependent device handling
Previously, we wanted SCSI devices corrsponding to ATA devices to
be runtime resumed when the power resource for those ATA device was
turned on by some other device, so we added the SCSI device to the
dependent device list of the ATA device's ACPI node. However, this
code has no effect after commit 41863fc (ACPI / power: Drop automaitc
resume of power resource dependent devices) and the mechanism it was
supposed to implement is regarded as a bad idea now, so drop it.
[rjw: Changelog] Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukasz Majewski [Wed, 9 Oct 2013 12:08:43 +0000 (14:08 +0200)]
cpufreq: exynos4210: Use the common clock framework to set APLL clock rate
In the exynos4210_set_apll() function, the APLL frequency is set with
direct register manipulation.
Such approach is not allowed in the common clock framework. The frequency
is changed, but the corresponding clock value is not updated. This causes
wrong frequency read from cpufreq's cpuinfo_cur_freq sysfs attribute.
Also direct manipulation with PLL's S parameter has been removed. It is
already done at PLL35xx code.
Lukasz Majewski [Wed, 9 Oct 2013 12:08:42 +0000 (14:08 +0200)]
cpufreq: exynos4x12: Use the common clock framework to set APLL clock rate
In the exynos4x12_set_apll() function, the APLL frequency is set with
direct register manipulation.
Such approach is not allowed in the common clock framework. The frequency
is changed, but the corresponding clock value is not updated. This causes
wrong frequency read from cpufreq's cpuinfo_cur_freq sysfs attribute.
Also direct manipulation with PLL's S parameter has been removed. It is
already done at PLL35xx code.
cpufreq: Detect spurious invocations of update_policy_cpu()
The function update_policy_cpu() is expected to be called when the policy->cpu
of a cpufreq policy is to be changed: ie., the new CPU nominated to become the
policy->cpu is different from the old one.
Print a warning if it is invoked with new_cpu == old_cpu, since such an
invocation might hint at a faulty logic in the caller.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaro Koskinen [Mon, 30 Sep 2013 20:44:33 +0000 (23:44 +0300)]
cpufreq: pmac64: enable cpufreq on iMac G5 (iSight) model
Enable cpufreq on iMac G5 (iSight) model. Tested with the 2.1 GHz version.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaro Koskinen [Mon, 30 Sep 2013 20:44:32 +0000 (23:44 +0300)]
cpufreq: pmac64: provide cpufreq transition latency for older G5 models
Currently cpufreq ondemand governor cannot used on older G5 models,
because the transition latency is set to CPUFREQ_ETERNAL. Provide a
value based on a measurement on Xserve G5, which happens to be also the
highest allowed latency.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaro Koskinen [Mon, 30 Sep 2013 20:44:31 +0000 (23:44 +0300)]
cpufreq: pmac64: speed up frequency switch
Some functions on switch path use msleep() which is inaccurate, and
depends on HZ. With HZ=100 msleep(1) takes actually over ten times longer.
Using usleep_range() we get more accurate sleeps.
I measured the "pfunc_slewing_done" polling to take 300us at max (on
2.3GHz dual-processor Xserve G5), so using 500us sleep there should
be fine.
With the patch, g5_switch_freq() duration drops from ~50ms to ~10ms on
Xserve with HZ=100.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Mark Langsdorf [Tue, 1 Oct 2013 15:30:24 +0000 (10:30 -0500)]
cpufreq: highbank-cpufreq: Enable Midway/ECX-2000
Calxeda's new ECX-2000 part uses the same cpufreq interface as highbank,
so add it to the driver's compatibility list.
This is a minor change that can safely be applied to the 3.10 and 3.11
stable trees.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Manish Badarkhe [Wed, 9 Oct 2013 15:13:37 +0000 (20:43 +0530)]
exynos-cpufreq: fix false return check from "regulator_set_voltage"
Currently, code checks false return value from "regulator_set_voltage"
to show failure message. Modify the code to check proper return
value from "regulator_set_voltage".
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adding BIT(x) equivalent for unsigned long long type, BIT_ULL(x). Also
added BIT_ULL_MASK and BIT_ULL_WORD.
Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jacob Pan [Fri, 11 Oct 2013 23:54:58 +0000 (16:54 -0700)]
x86 / msr: add 64bit _on_cpu access functions
Having 64-bit MSR access methods on given CPU can avoid shifting and
simplify MSR content manipulation. We already have other combinations
of rdmsrl_xxx and wrmsrl_xxx but missing the _on_cpu version.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Reviewed-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added changes to Makefile and Kconfig to include in driver build.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The power capping framework providing a consistent interface between the
kernel and user space that allows power capping drivers to expose their
settings to user space in a uniform way.
The overall design of the framework is described in the documentation
added by the previous patch in this series.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added power cap framework documentation. This explains the use of power
capping framework, sysfs and programming interface.
There are two documents:
- Documentation/power/powercap/powercap.txt : Explains use case and APIs.
- Documentation/ABI/testing/sysfs-class-powercap: Explains ABIs.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge branch 'cpuidle/arm-next' of git://git.linaro.org/people/dlezcano/linux into pm-cpuidle
Pull cpuidle updates for v3.13 from Daniel Lezcano:
- Daniel Lezcano converted cpuidle to a platform_driver for at91.
The standby callback is stored in the platform_device's data
field as a callback for the driver, so the pm specific code and
the backend driver have no more dependency. Each SoC init function
fills the right callback at init time. As there are no more
dependency, we can move the driver in the drivers/cpuidle directory.
- Jean-Christophe Plagnol-Villard and Nicolas Ferre made a cleanup on
top of the patch described above and fixed up the ddr standby callback
so more SoC are supported. Even if the modifications are in the
mach-at91 directory, they asked these patches to be included through
the PM tree as they depend on the platform_driver conversion.
* 'cpuidle/arm-next' of git://git.linaro.org/people/dlezcano/linux:
ARM: AT91: DT: pm: Select ram controller standby based on DT
ARM: AT91: pm: Factorize standby function
ARM: at91: cpuidle: Move driver to drivers/cpuidle
ARM: at91: cpuidle: Convert to platform driver
Viresh Kumar [Wed, 16 Oct 2013 21:58:10 +0000 (23:58 +0200)]
acpi-cpufreq: Add comment under ACPI_ADR_SPACE_SYSTEM_IO case
policy->cur is now set by cpufreq core when cpufreq_driver->get() is defined and
so drivers aren't required to set it. When space_id is ACPI_ADR_SPACE_SYSTEM_IO
for acpi cpufreq driver it doesn't set ->get to a valid function pointer and so
policy->cur is required to be set by driver.
This is already followed in acpi-cpufreq driver. This patch adds a comment
describing why we need to set policy->cur from driver.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Charles Keepax [Mon, 14 Oct 2013 18:36:47 +0000 (19:36 +0100)]
cpufreq: s3c64xx: Rename index to driver_data
The index field of cpufreq_frequency_table has been renamed to
driver_data by commit 5070158 (cpufreq: rename index as driver_data
in cpufreq_frequency_table).
This patch updates the s3c64xx driver to match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Cc: 3.11+ <stable@vger.kernel.org> # 3.11+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Detect presence of second bank. So we do not need to have on function per SoC
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Daniel Lezcano [Thu, 26 Sep 2013 15:34:24 +0000 (17:34 +0200)]
ARM: at91: cpuidle: Move driver to drivers/cpuidle
As the cpuidle driver code has no more the dependency with the pm code, the
'standby' callback being passed as a parameter to the device's platform data,
we can move the cpuidle driver in the drivers/cpuidle directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
Daniel Lezcano [Sun, 22 Sep 2013 20:29:57 +0000 (22:29 +0200)]
ARM: at91: cpuidle: Convert to platform driver
Using the platform driver model is a good way to separate the cpuidle specific
code from the low level pm code. It allows to remove the dependency between
these two components.
The platform_device is located in the pm code and a 'set' function has been
added to set the standby function from the AT91_SOC_START initialization
function. Each SoC with a cpuidle driver will set the standby function in the
platform_data field at init time. Then pm code will register the cpuidle
platform device.
The cpuidle driver will register the platform_driver and use the device's
platform_data as a standby callback in the idle path.
The at91_pm_enter function contains a { if then else } based on cpu_is_xx
similar to what was in cpuidle. This is considered dangerous when adding a new
SoC. Like the cpuidle driver, a standby ops is defined and assigned when the
SoC init function specifies what is its standby function and reused in the
at91_pm_enter's 'case' block.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jungseok Lee [Mon, 14 Oct 2013 23:31:13 +0000 (08:31 +0900)]
cpufreq: exynos: Show a list of available frequencies
This patch adds freq_attr to show a list of exynos5440 scaling
available frequencies through sysfs. Common exynos driver already
supports this attribute.
Signed-off-by: Jungseok Lee <jays.lee@samsung.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / power: Drop automaitc resume of power resource dependent devices
The mechanism causing devices depending on a given power resource
(that is, devices that can be in D0 only if that power resource is
on) to be resumed automatically when the power resource is turned
on (and their "inferred" power state becomes D0 as a result) is
inherently racy and in fact unnecessary.
It is racy, because if the power resource is turned on and then
immediately off, the device resume triggered by the first transition
to "on" may still happen, causing the power resource to be turned
on again. That again will trigger the "resume of dependent devices"
mechanism, but if the devices in question are not in use, they will
be suspended in the meantime causing the power resource to be turned
off. However, the "resume of dependent devices" will next resume
them again and so on. In some cases (USB port PM in particular) that
leads to an endless busy loop of flipping the resource on and off
continuously.
It is needless, because whoever turns a power resource on will most
likely turn it off at some point and the devices that go into "D0"
as a result of turning it on will then go back into D3cold
(generally, the state they were in before).
Moreover, turning on all power resources a device needs to go into
D0 is not sufficient for a full transition into D0 in general.
Namely, _PS0 may need to be executed in addition to that in some
cases. This means that the whole rationale of the "resume of
dependent devices" mechanism was incorrect to begin with and it's
best to remove it entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq-next: (147 commits)
cpufreq: sa11x0: Fix build breakage after "Expose frequency table"
cpufreq: tegra: use cpufreq_generic_init()
cpufreq: spear: use cpufreq_generic_init()
cpufreq: sa11x0: use cpufreq_generic_init()
cpufreq: s5pv210: use cpufreq_generic_init()
cpufreq: s3c: use cpufreq_generic_init()
cpufreq: pmac64: use cpufreq_generic_init()
cpufreq: pmac32: use cpufreq_generic_init()
cpufreq: pasemi: use cpufreq_generic_init()
cpufreq: omap: use cpufreq_generic_init()
cpufreq: maple: use cpufreq_generic_init()
cpufreq: loongson2: use cpufreq_generic_init()
cpufreq: kirkwood: use cpufreq_generic_init()
cpufreq: imx6q: use cpufreq_generic_init()
cpufreq: exynos: use cpufreq_generic_init()
cpufreq: dbx500: use cpufreq_generic_init()
cpufreq: davinci: use cpufreq_generic_init()
cpufreq: cris: use cpufreq_generic_init()
cpufreq: cpufreq-cpu0: use cpufreq_generic_init()
cpufreq: remove CONFIG_CPU_FREQ_TABLE
...
* pm-cpuidle-next:
ARM: ux500: cpuidle: fix section mismatch
ARM: zynq: cpuidle: convert to platform driver
ARM: zynq: cpuidle: Remove useless compatibility string
drivers: cpuidle: rename ARM big.LITTLE driver config and makefile entries
ARM: EXYNOS: convert cpuidle driver to be a platform driver
intel_idle: mark some functions with __init tag
intel_idle: mark states tables with __initdata tag
intel_idle: shrink states tables
* acpi-video-next:
ACPI / video: Add Lenovo IdeaPad Yoga 13 to acpi video detect blacklist
thinkpad-acpi: fix handle locate for video and query of _BCL
ACPI / video: Do not register backlight if win8 and native interface exists
ACPI / video: seperate backlight control and event interface
backlight: introduce backlight_device_registered
ACPI: add missing win8 OSI comment to blacklist
ACPI: update win8 OSI blacklist
* acpi-assorted-next:
ACPI / platform: add ACPI ID for a Broadcom GPS chip
ACPI: improve acpi_extract_package() utility
ACPI / LPSS: fix UART Auto Flow Control
ACPI / platform: Add ACPI IDs for Intel SST audio device
x86 / ACPI: fix incorrect placement of __initdata tag
ACPI / thermal: convert printk(LEVEL...) to pr_<lvl>
ACPI / sysfs: make GPE sysfs attributes only accept correct values
ACPI / EC: Convert all printk() calls to dynamic debug function
ACPI / button: Using input_set_capability() to mark device's event capability
ACPI / osl: implement acpi_os_sleep() with msleep()
Ulf Hansson [Tue, 15 Oct 2013 20:25:08 +0000 (22:25 +0200)]
PM / Runtime: Respect autosuspend when idle triggers suspend
For devices which don't have a .runtime_idle() callback or if it
returns 0, rpm_idle() will end up in triggering a call to
rpm_suspend(), thus trying to carry out a runtime suspend directly
from runtime_idle().
In the above situation we want to respect devices which has enabled
autosuspend, we therfore append the flag sent to rpm_suspend with
RPM_AUTO.
Do note that drivers still needs to update the device last busy mark,
to control the delay for this circumstance.
Updated runtime PM documentation accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Kevin Hilman <khilman@linaro.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pm-next:
spi: attach/detach SPI device to the ACPI power domain
i2c: attach/detach I2C client device to the ACPI power domain
ACPI / PM: allow child devices to ignore parent power state
Merge branch 'acpi-conversion-next' into linux-next
* acpi-conversion-next:
ACPI / AC: Remove AC's proc directory.
ideapad_laptop: convert ideapad device/driver to platform bus
ideapad_laptop: remove ideapad_handle and ideapad_priv
ideapad_laptop: convert internal function calls to use ideapad_private as parameter
ideapad_laptop: introduce struct acpi_device pointer to ideapad_private structure
ideapad_laptop: introduce #ifdef CONFIG_PM_SLEEP for PM specific code
ACPI / AC: convert ACPI ac driver to platform bus
* acpi-hotplug-next:
ACPI / memhotplug: Use defined marco METHOD_NAME__STA
ACPI / hotplug: Use kobject_init_and_add() instead of _init() and _add()
ACPI / hotplug: Don't set kobject parent pointer explicitly
ACPI / hotplug: Set kobject name via kobject_add(), not kobject_set_name()
hotplug, powerpc, x86: Remove cpu_hotplug_driver_lock()
hotplug / x86: Disable ARCH_CPU_PROBE_RELEASE on x86
hotplug / x86: Add hotplug lock to missing places
hotplug / x86: Fix online state in cpu0 debug interface
* acpica-next:
MAINTAINERS / ACPICA: Add ACPICA information to MAINTAINERS
ACPICA: Update version to 20130823.
ACPICA: SCI Handlers: Update handler interface, eliminate unnecessary argument.
ACPICA: Cleanup exception codes.
ACPICA: Tables: Cleanup RSDP signature codes.
ACPICA: Tables: Cleanup table checksum verification code.
ACPICA: Debugger: Add new command to display full namespace pathnames.
ACPICA: Operation region support: Never free the handler "context" pointer.
ACPICA: Add support for host-installed SCI handlers.
ACPICA: Validate start object for acpi_walk_namespace.
ACPICA: Debugger: Prevent possible command line buffer overflow, kernel behavior is not affected.
ACPICA: Linux-specific header: enable "aarch64" 64-bit build.
ACPICA: Debug output: small formatting update, no functional change.
ACPICA: acpi_read: On error, do not modify the return value target location.
ACPICA: Improve error message for "too many parent prefixes" condition.
Dirk Brandewie [Tue, 15 Oct 2013 18:06:14 +0000 (11:06 -0700)]
cpufreq / intel_pstate: Fix max_perf_pct on resume
If the system is suspended while max_perf_pct is less than 100 percent
or no_turbo set policy->{min,max} will be set incorrectly with scaled
values which turn the scaled values into hard limits.
References: https://bugzilla.kernel.org/show_bug.cgi?id=61241 Reported-by: Patrick Bartels <petzicus@googlemail.com> Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Cc: 3.9+ <stable@vger.kernel.org> # 3.9+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / video: Add Lenovo IdeaPad Yoga 13 to acpi video detect blacklist
On the Yoga 13 the backlight control doesn't work via ACPI. (And doesn't
work either with the low-level platform driver ideapad_laptop; but
works correctly via the intel video driver). This patch hence adds the
Yoga 13 to the ACPI video detect blacklist, to make sure the broken ACPI
backlight device is never exposed to userspace.
Note that this appears unrelated to the Windows 8 backlight issues tracked
here:
The Yoga's ACPI backlight controls work neither with nor without
acpi_osi="!Windows 2012" on the kernel command line. It appears that
backlight control via the EC simply is not available at all, regardless
whether done via ACPI or via the vendor driver.
Signed-off-by: Lennart Poettering <lennart@poettering.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaron Lu [Fri, 11 Oct 2013 13:27:46 +0000 (21:27 +0800)]
thinkpad-acpi: fix handle locate for video and query of _BCL
The tpacpi_acpi_handle_locate function makes use of acpi_get_devices to
locate handle for ACPI video by HID, the problem is, ACPI video node
doesn't really have HID defined(i.e. no _HID control method is defined
for video device), so.. that function would fail. This can be solved by
enhancing the callback function for acpi_get_devices, where we can use
acpi_device_hid function to check if the ACPI node corresponds to a
video controller.
In addition to that, the _BCL control method only exists under a video
output device node, not a video controller device node. So to evaluate
_BCL, we need the handle of a video output device node, which is child
of the located video controller node from tpacpi_acpi_handle_locate.
The two fix are necessary for some Thinkpad models to emit notification
on backlight hotkey press as a result of evaluation of _BCL.
Signed-off-by: Aaron Lu <aaron.lu@intel.com> Tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaron Lu [Fri, 11 Oct 2013 13:27:45 +0000 (21:27 +0800)]
ACPI / video: Do not register backlight if win8 and native interface exists
According to Matthew Garrett, "Windows 8 leaves backlight control up
to individual graphics drivers rather than making ACPI calls itself.
There's plenty of evidence to suggest that the Intel driver for
Windows [8] doesn't use the ACPI interface, including the fact that
it's broken on a bunch of machines when the OS claims to support
Windows 8. The simplest thing to do appears to be to disable the
ACPI backlight interface on these systems".
So for Win8 systems, if there is native backlight control interface
registered by GPU driver, ACPI video does not need to register its own.
Since there are systems that don't work well with this approach, a
parameter for video module named use_native_backlight is introduced and
has the value of false by default. For users who have a broken ACPI
video backlight interface, video.use_native_backlight=1 is needed in
kernel cmdline.
Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaron Lu [Fri, 11 Oct 2013 13:27:44 +0000 (21:27 +0800)]
ACPI / video: seperate backlight control and event interface
The backlight control and event delivery functionality provided by ACPI
video module is mixed together and registered all during video device
enumeration time. As a result, the two functionality are also removed
together on module unload time or by the acpi_video_unregister function.
The two functionalities are actually independent and one may be useful
while the other one may be broken, so it is desirable to seperate the
two functionalities such that it is clear and easy to disable one
functionality without affecting the other one.
APIs to selectively remove backlight control interface and/or event
delivery functionality can be easily added once needed.
Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaron Lu [Fri, 11 Oct 2013 13:27:43 +0000 (21:27 +0800)]
backlight: introduce backlight_device_registered
Introduce a new API for modules to query if a specific type of backlight
device has been registered. This is useful for some backlight device
provider module (e.g. ACPI video) to know if a native control
interface(e.g. the interface created by i915) is available and then do
things accordingly (e.g. avoid registering its own on Win8 systems).
Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:59:20 +0000 (20:29 +0530)]
cpufreq: pmac32: use cpufreq_generic_init()
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:59:16 +0000 (20:29 +0530)]
cpufreq: loongson2: use cpufreq_generic_init()
Use generic cpufreq_generic_init() routine instead of replicating the same code
here. This driver wasn't setting transition_latency and so is getting set to 0
by default. Lets mark it explicitly by calling the generic routine with
transition_latency as 0.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:59:08 +0000 (20:29 +0530)]
cpufreq: remove CONFIG_CPU_FREQ_TABLE
CONFIG_CPU_FREQ_TABLE will be always enabled when cpufreq framework is used, as
cpufreq core depends on it. So, we don't need this CONFIG option anymore as it
is not configurable. Remove CONFIG_CPU_FREQ_TABLE and update its users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:59:05 +0000 (20:29 +0530)]
cpufreq: tegra: don't initialize part of policy set by core
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:59:04 +0000 (20:29 +0530)]
cpufreq: speedstep: don't initialize part of policy set by core
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:59:02 +0000 (20:29 +0530)]
cpufreq: sh: don't initialize part of policy set by core
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:59:00 +0000 (20:29 +0530)]
cpufreq: sa11x0: don't initialize part of policy set by core
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:58:59 +0000 (20:28 +0530)]
cpufreq: s5pv210: don't initialize part of policy set by core
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:58:58 +0000 (20:28 +0530)]
cpufreq: s3c: don't initialize part of policy set by core
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 3 Oct 2013 14:58:57 +0000 (20:28 +0530)]
cpufreq: pxa: don't initialize part of policy set by core
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
projects / karo-tx-linux.git / log