Merge branch 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip
* 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86, iommu: Mark DMAR IRQ as non-threaded
genirq: Make irq_shutdown() symmetric vs. irq_startup again
Merge branch 'for-linus' of git://github.com/chrismason/linux
* 'for-linus' of git://github.com/chrismason/linux:
Btrfs: only clear the need lookup flag after the dentry is setup
BTRFS: Fix lseek return value for error
Btrfs: don't change inode flag of the dest clone file
Btrfs: don't make a file partly checksummed through file clone
Btrfs: fix pages truncation in btrfs_ioctl_clone()
btrfs: fix d_off in the first dirent
USB: xHCI: prevent infinite loop when processing MSE event
When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.
Currently xhci driver handles MSE event in the following ways:
1. When encounter a MSE event, set ep->skip flag, update event ring
dequeue pointer and return.
2. When encounter the next event on this ep, the driver will run the
do-while loop, fetch td from ep's td_list to find the td
corresponding to this event. All tds missed are marked as short
transfer(-EXDEV).
The do-while loop will end in two ways:
1. If the td pointed by the event trb is found;
2. If the ep ring's td_list is empty.
However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.
Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop. During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list. This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.
To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds. This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
USB: xhci: Set change bit when warm reset change is set.
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive". This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.
When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd. However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.
After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits. (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted. Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.
A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up. That more
complicated fix will be merged next window, and this fix will be
backported to stable.
This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf375 ("xHCI: warm reset support").
Randy Dunlap [Mon, 19 Sep 2011 23:05:10 +0000 (16:05 -0700)]
staging: fix comedi build when ISA_DMA_API is enabled but COMEDI_PCI is not enabled
Fix build when CONFIG_ISA_DMA_API is enabled but
CONFIG_COMEDI_PCI[_DRIVERS] is not enabled.
Fixes these build errors:
drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd':
drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c: At top level:
drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here
Make taskstats round statistics down to nearest 1k bytes/events
Even with just the interface limited to admin, there really is little to
reason to give byte-per-byte counts for taskstats. So round it down to
something less intrusive.
Ok, this isn't optimal, since it means that 'iotop' needs admin
capabilities, and we may have to work on this some more. But at the
same time it is very much not acceptable to let anybody just read
anybody elses IO statistics quite at this level.
Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative
to checking the capabilities by hand.
In ad-hoc mode, driver b43 does not issue beacons.
Signed-off-by: Manual Munz <freifunk@somakoma.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
drm/radeon/kms: fix typo in r100_blit_copy
drm/radeon: Unreference GEM object outside of spinlock in page flip error path.
drm/radeon: Don't read from CP ring write pointer registers.
drm/ttm: request zeroed system memory pages for new TT buffer objects
ALSA: hda/realtek - Fix auto-mute with HP+LO configuration
When the system has only the headphone and the line-out jacks without
speakers, the current auto-mute code doesn't work. It's because the
spec->automute_lines flag is wrongly referred in update_speakers().
This flag must be meaningless when spec->automute_hp_lo isn't set, thus
they should be always coupled.
The patch fixes the problem and add a comment to indicate the
relationship briefly.
BugLink: http://bugs.launchpad.net/bugs/851697 Reported-by: David Henningsson <david.henningsson@canonical.com> Tested-By: Jayne Han <jayne.han@canonical.com> Cc: stable@kernel.org (3.0) Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eric Dumazet [Mon, 19 Sep 2011 01:02:55 +0000 (21:02 -0400)]
tcp: fix build error if !CONFIG_SYN_COOKIES
commit 946cedccbd7387 (tcp: Change possible SYN flooding messages)
added a build error if CONFIG_SYN_COOKIES=n
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6
* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6:
mfd: Fix omap-usb-host build failure
mfd: Make omap-usb-host TLL mode work again
mfd: Set MAX8997 irq pointer
mfd: Fix initialisation of tps65910 interrupts
mfd: Check for twl4030-madc NULL pointer
mfd: Copy the device pointer to the twl4030-madc structure
mfd: Rename wm8350 static gpio_set_debounce()
mfd: Fix value of WM8994_CONFIGURE_GPIO
Alex Deucher [Fri, 16 Sep 2011 16:04:08 +0000 (12:04 -0400)]
drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
The BO blit code inconsistenly handled the page size. This wasn't
an issue on system with 4k pages since the GPU's page size is 4k as
well. Switch the driver blit callbacks to take num pages in GPU
page units.
Fixes lemote mipsel systems using AMD rs780/rs880 chipsets.
v2: incorporate suggestions from Michel.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Fri, 16 Sep 2011 16:04:07 +0000 (12:04 -0400)]
drm/radeon/kms: fix typo in r100_blit_copy
cur_pages is the number of pages per loop iteration.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://github.com/davem330/net: (62 commits)
ipv6: don't use inetpeer to store metrics for routes.
can: ti_hecc: include linux/io.h
IRDA: Fix global type conflicts in net/irda/irsysctl.c v2
net: Handle different key sizes between address families in flow cache
net: Align AF-specific flowi structs to long
ipv4: Fix fib_info->fib_metrics leak
caif: fix a potential NULL dereference
sctp: deal with multiple COOKIE_ECHO chunks
ibmveth: Fix checksum offload failure handling
ibmveth: Checksum offload is always disabled
ibmveth: Fix issue with DMA mapping failure
ibmveth: Fix DMA unmap error
pch_gbe: support ML7831 IOH
pch_gbe: added the process of FIFO over run error
pch_gbe: fixed the issue which receives an unnecessary packet.
sfc: Use 64-bit writes for TX push where possible
Revert "sfc: Use write-combining to reduce TX latency" and follow-ups
bnx2x: Fix ethtool advertisement
bnx2x: Fix 578xx link LED
bnx2x: Fix XMAC loopback test
...
Josef Bacik [Sun, 18 Sep 2011 14:34:03 +0000 (10:34 -0400)]
Btrfs: only clear the need lookup flag after the dentry is setup
We can race with readdir and the RCU path walking stuff. This is because we
clear the need lookup flag before actually instantiating the inode. This will
lead the RCU path walk stuff to find a dentry it thinks is valid without a
d_inode attached. So instead unhash the dentry when we first start the lookup,
and then clear the flag after we've instantiated the dentry so we're garunteed
to either try the slow lookup, or have the d_inode set properly.
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Jeff Liu [Sun, 18 Sep 2011 14:34:02 +0000 (10:34 -0400)]
BTRFS: Fix lseek return value for error
The recent reworking of btrfs' lseek lead to incorrect
values being returned. This adds checks for seeking
beyond EOF in SEEK_HOLE and makes sure the error
values come back correct.
Andi Kleen also sent in similar patches.
Signed-off-by: Jie Liu <jeff.liu@oracle.com> Reported-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Since the d_off in the first dirent for "." (that originates from
the 4th argument "offset" of filldir() for the 2nd dirent for "..")
is wrongly assigned in btrfs_real_readdir(), telldir returns same
offset for different locations.
At the moment the "offset" for "." is unused because there is no
preceding dirent, however it is better to pass filp->f_pos to follow
grammatical usage.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Merge branch '3.1-rc-fixes' of git://linux-iscsi.org/target-pending
* '3.1-rc-fixes' of git://linux-iscsi.org/target-pending:
iscsi-target: Fix sendpage breakage with proper padding+DataDigest iovec offsets
iscsi-target: Disable markers + remove dangerous local scope array usage
target: Skip non hex characters for VPD=0x83 NAA IEEE Registered Extended
tcm_fc: Work queue based approach instead of managing own thread and event based mechanism
tcm_fc: Invalidation of DDP context for FCoE target in error conditions
target: Fix race between multiple invocations of target_qf_do_work()
This patch against current git adds the hardware ID for the Apple
MacBookAir4,1, released in July 2011. The device features a BCM2046
USB chip. The patch was inspired by the previous modifications adding
support for the MacBookAir3,x.
Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Chen Ganir [Tue, 30 Aug 2011 10:58:28 +0000 (13:58 +0300)]
Bluetooth: Fixed BT ST Channel reg order
Reordered the BT ST channel registration, to make sure that the
event channel is registered before all others. This prevents a
situation where incoming events may cause kernel panic in the ST
driver if the event channel is not yet registered to handle
incoming events.In addition, the deregistration of the channels
was also modified, to be in the reversed order of the registration,
to allow the event channel to be the last one unregistered.
Signed-off-by: Chen Ganir <chen.ganir@ti.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
ipv6: don't use inetpeer to store metrics for routes.
Current IPv6 implementation uses inetpeer to store metrics for
routes. The problem of inetpeer is that it doesn't take subnet
prefix length in to consideration. If two routes have the same
address but different prefix length, they share same inetpeer.
So changing metrics of one route also affects the other. The
fix is to allocate separate metrics storage for each route.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
iscsi-target: Fix sendpage breakage with proper padding+DataDigest iovec offsets
This patch fixes a bug in the iscsit_fe_sendpage_sg() transmit codepath that
was originally introduced with the v3.1 iscsi-target merge that incorrectly
uses hardcoded cmd->iov_data_count values to determine cmd->iov_data[] offsets
for extra outgoing padding and DataDigest payload vectors.
This code is obviously incorrect for the DataDigest enabled case with sendpage
offload, and this fix ensures correct operation for padding + DataDigest,
padding only, and DataDigest only cases. The bug was introduced during a
pre-merge change in iscsit_fe_sendpage_sg() to natively use struct scatterlist
instead of the legacy v3.0 struct se_mem logic.
Cc: Andy Grover <agrover@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Daniel Mack [Fri, 16 Sep 2011 07:57:43 +0000 (07:57 +0000)]
can: ti_hecc: include linux/io.h
This fixes a build breakage for OMAP3 boards.
Signed-off-by: Daniel Mack <zonque@gmail.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: netdev@vger.kernel.org Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Handle different key sizes between address families in flow cache
With the conversion of struct flowi to a union of AF-specific structs, some
operations on the flow cache need to account for the exact size of the key.
Signed-off-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 2 Sep 2011 02:19:23 +0000 (02:19 +0000)]
caif: fix a potential NULL dereference
Commit bd30ce4bc0b7 (caif: Use RCU instead of spin-lock in caif_dev.c)
added a potential NULL dereference in case alloc_percpu() fails.
caif_device_alloc() can also use GFP_KERNEL instead of GFP_ATOMIC.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Sjur Brændeland <sjur.brandeland@stericsson.com> Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Max Matveev [Mon, 29 Aug 2011 21:02:24 +0000 (21:02 +0000)]
sctp: deal with multiple COOKIE_ECHO chunks
Attempt to reduce the number of IP packets emitted in response to single
SCTP packet (2e3216cd) introduced a complication - if a packet contains
two COOKIE_ECHO chunks and nothing else then SCTP state machine corks the
socket while processing first COOKIE_ECHO and then loses the association
and forgets to uncork the socket. To deal with the issue add new SCTP
command which can be used to set association explictly. Use this new
command when processing second COOKIE_ECHO chunk to restore the context
for SCTP state machine.
Signed-off-by: Max Matveev <makc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei [Wed, 31 Aug 2011 02:45:46 +0000 (10:45 +0800)]
firewire: ohci: add no MSI quirk for O2Micro controller
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 .
An O2Micro PCI Express FireWire controller,
"FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)"
which is a combination device together with an SDHCI controller and some
sort of storage controller, misses SBP-2 status writes from an attached
FireWire HDD. This problem goes away if MSI is disabled for this
FireWire controller.
The device reportedly does not require QUIRK_CYCLE_TIMER.
Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (amended changelog) Cc: <stable@kernel.org>
iscsi-target: Disable markers + remove dangerous local scope array usage
This patch makes iscsi-target explictly disable OFMarker=Yes and IFMarker=yes
parameter key usage during iscsi login by setting IFMarkInt_Reject and
OFMarkInt_Reject values in iscsi_enforce_integrity_rules() to effectively
disable iscsi marker usage. With this patch, an initiator proposer asking
to enable either marker parameter keys will be issued a 'No' response, and
the target sets OFMarkInt + IFMarkInt parameter key response to 'Irrelevant'.
With markers disabled during iscsi login, this patch removes the problematic
on-stack local-scope array for marker intervals in iscsit_do_rx_data() +
iscsit_do_tx_data(), and other related marker code in iscsi_target_util.c.
This fixes a potentional stack smashing scenario with small range markers
enabled and a large MRDSL as reported by DanC here:
[bug report] target: stack can be smashed
http://www.spinics.net/lists/target-devel/msg00453.html
Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Skip non hex characters for VPD=0x83 NAA IEEE Registered Extended
This patch adds target_parse_naa_6h_vendor_specific() to address a bug where the
conversion of PRODUCT SERIAL NUMBER to use hex2bin() in target_emulate_evpd_83()
was not doing proper isxdigit() checking. This conversion of the vpd_unit_serial
configifs attribute is done while generating a VPD=0x83 NAA IEEE Registered
Extended DESIGNATOR format's 100 bits of unique VENDOR SPECIFIC IDENTIFIER +
VENDOR SPECIFIC IDENTIFIER EXTENSION area.
This patch allows vpd_unit_serial (VPD=0x80) and the T10 Vendor ID DESIGNATOR
format (VPD=0x83) to continue to use free-form variable length ASCII values,
and now skips any non hex characters for fixed length NAA IEEE Registered Extended
DESIGNATOR format (VPD=0x83) requring the binary conversion.
This was originally reported by Martin after the v3.1-rc1 change to use hex2bin()
in commit 11650b859681e03fdbf26277fcfc5f1f62186703 where the use of non hex
characters in vpd_unit_serial generated different values than the original
v3.0 internal hex -> binary code. This v3.1 change caused a problem with
filesystems who write a NAA DESIGNATOR onto it's ondisk metadata, and this patch
will (again) change existing values to ensure that non hex characters are not
included in the fixed length NAA DESIGNATOR.
Note this patch still expects vpd_unit_serial to be set via existing userspace
methods of uuid generation, and does not do strict formatting via configfs input.
The original bug report and thread can be found here:
The v3.1-rc1 formatting of VPD=0x83 w/o this patch:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 6, IEEE Company_id: 0x1405
Vendor Specific Identifier: 0xffde35ebf
Vendor Specific Identifier Extension: 0x3092f498ffa820f9
[0x6001405ffde35ebf3092f498ffa820f9]
Designation descriptor number 2, descriptor length: 56
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: LIO-ORG
vendor specific: IBLOCK:ffde35ec-3092-4980-a820-917636ca54f1
The v3.1-final formatting of VPD=0x83 w/ this patch:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 6, IEEE Company_id: 0x1405
Vendor Specific Identifier: 0xffde35ec3
Vendor Specific Identifier Extension: 0x924980a82091763
[0x6001405ffde35ec30924980a82091763]
Designation descriptor number 2, descriptor length: 56
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: LIO-ORG
vendor specific: IBLOCK:ffde35ec-3092-4980-a820-917636ca54f1
(v2: Fix parsing code to dereference + check for string terminator instead
of null pointer to ensure a zeroed payload for vpd_unit_serial less
than 100 bits of NAA DESIGNATOR VENDOR SPECIFIC area. Also, remove
the unnecessary bitwise assignment)
Reported-by: Martin Svec <martin.svec@zoner.cz> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Don Fry [Thu, 15 Sep 2011 15:36:22 +0000 (08:36 -0700)]
iwlagn: workaround bug crashing some APs
This patch reverts commit 9b7688328422b88a7a15dc0dc123ad9ab1a6e22d which
was introduced in 2.6.38-rc1. It works around a problem where the iwlagn
driver stimulates a bug crashing (requiring power cycle to recover) some
APs under heavy traffic.
CC: stable@kernel.org #2.6.39, #3.0.0 #3.1.0 Signed-off-by: Don Fry <donald.h.fry@intel.com> SIgned-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan request received from cfg80211_connect do not
have proper rate mast. So the probe request sent on each
channel do not have proper the supported rates ie.
Cc: stable@kernel.org Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 14 Sep 2011 21:50:23 +0000 (16:50 -0500)]
rtl2800usb: Fix incorrect storage of MAC address on big-endian platforms
The eeprom data is stored in little-endian order in the rt2x00 library.
As it was converted to cpu order in the read routines, the data need to
be converted to LE on a big-endian platform.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 14 Sep 2011 21:50:22 +0000 (16:50 -0500)]
rt2800pci: Fix compiler error on PowerPC
Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated
if statement results in incorrect flow, whereas the equivalent switch
statement works correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: fix suspend/resume races with unregister hw
Above commit add rtnl_lock() into wiphy_register(), what cause deadlock
when initializing ipw2x00 driver, which itself call wiphy_register()
from register_netdev() internal callback with rtnl mutex taken.
To fix move wiphy_register() outside register_netdev(). This solution
have side effect of not creating /sys/class/net/wlanX/phy80211 link,
but that's a minor issue we can live with.
Bisected-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl> Bisected-by: Michael Witten <mfwitten@gmail.com> Tested-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl> Tested-by: Michael Witten <mfwitten@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless: Reset beacon_found while updating regulatory
During the association, the regulatory is updated by country IE
that reaps the previously found beacons. The impact is that
after a STA disconnects *or* when for any reason a regulatory
domain change happens the beacon hint flag is not cleared
therefore preventing future beacon hints to be learned.
This is important as a regulatory domain change or a restore
of regulatory settings would set back the passive scan and no-ibss
flags on the channel. This is the right place to do this given that
it covers any regulatory domain change.
Cc: stable@kernel.org Reviewed-by: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Anton Blanchard [Wed, 7 Sep 2011 14:41:06 +0000 (14:41 +0000)]
ibmveth: Fix checksum offload failure handling
Fix a number of issues in ibmveth_set_csum_offload:
- set_attr6 and clr_attr6 may be used uninitialised
- We store the result of the IPV4 checksum change in ret but overwrite
it in a couple of places before checking it again later. Add ret4
to make it obvious what we are doing.
- We weren't clearing the NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM flags
if the enable of that hypervisor feature failed.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Blanchard [Wed, 7 Sep 2011 14:41:05 +0000 (14:41 +0000)]
ibmveth: Checksum offload is always disabled
Commit b9367bf3ee6d (net: ibmveth: convert to hw_features) reversed
a check in ibmveth_set_csum_offload that results in checksum offload
never being enabled.
Signed-off-by: Anton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # 3.0+ Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Blanchard [Wed, 7 Sep 2011 14:41:04 +0000 (14:41 +0000)]
ibmveth: Fix issue with DMA mapping failure
descs[].fields.address is 32bit which truncates any dma mapping
errors so dma_mapping_error() fails to catch it.
Use a dma_addr_t to do the comparison. With this patch I was able
to transfer many gigabytes of data with IOMMU fault injection set
at 10% probability.
Signed-off-by: Anton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # v2.6.37+ Signed-off-by: David S. Miller <davem@davemloft.net>
Brian King [Wed, 7 Sep 2011 14:41:03 +0000 (14:41 +0000)]
ibmveth: Fix DMA unmap error
Commit 6e8ab30ec677 (ibmveth: Add scatter-gather support) introduced a
DMA mapping API inconsistency resulting in dma_unmap_page getting
called on memory mapped via dma_map_single. This was seen when
CONFIG_DMA_API_DEBUG was enabled. Fix up this API usage inconsistency.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Anton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # v2.6.37+ Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'stable/bug.fixes' of git://oss.oracle.com/git/kwilk/xen
* 'stable/bug.fixes' of git://oss.oracle.com/git/kwilk/xen:
xen/i386: follow-up to "replace order-based range checking of M2P table by linear one"
xen/irq: Alter the locking to use a mutex instead of a spinlock.
xen/e820: if there is no dom0_mem=, don't tweak extra_pages.
xen: disable PV spinlocks on HVM
tcm_fc: Work queue based approach instead of managing own thread and event based mechanism
Problem: Changed from wake_up_interruptible -> wake_up_process and
wait_event_interruptible-> schedule_timeout_interruptible broke the FCoE
target. Earlier approach of wake_up_interruptible was also looking at
'queue_cnt' which is not necessary, because it increment of 'queue_cnt'
with wake_up_inetrriptible / waker_up_process introduces race condition.
Fix: Instead of fixing the code which used wake_up_process and remove
'queue_cnt', using work_queue based approach is cleaner and acheives
same result. As well, work queue based approach has less programming
overhead and OS manages threads which processes work queues.
This patch is developed by Christoph Hellwig and reviwed+validated by
Kiran Patil.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Kiran Patil [Fri, 26 Aug 2011 16:25:25 +0000 (09:25 -0700)]
tcm_fc: Invalidation of DDP context for FCoE target in error conditions
Problem: HW DDP context wasn;t invalidated in case of ABORTS, etc...
This leads to the problem where memory pages which are used for DDP
as user descriptor could get reused for some other purpose (such as to
satisfy new memory allocation request either by kernel or user mode threads)
and since HW DDP context was not invalidated, HW continue to write to
those pages, hence causing memory corruption.
Fix: Either on incoming ABORTS or due to exchange time out, allowed the
target to cleanup HW DDP context if it was setup for respective ft_cmd.
Added new function to perform this cleanup, furthur it can be enhanced
for other cleanup activity.
Additinal Notes: To avoid calling ddp_done from multiple places, composed
the functionality in helper function "ft_invl_hw_context" and it is being
called from multiple places. Cleaned up code in function "ft_recv_write_data"
w.r.t DDP.
Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Roland Dreier [Sun, 28 Aug 2011 04:33:16 +0000 (21:33 -0700)]
target: Fix race between multiple invocations of target_qf_do_work()
When work is scheduled with schedule_work(), the work can end up
running on multiple CPUs at the same time -- this happens if
the work is already running on one CPU and schedule_work() is called
on another CPU. This leads to list corruption with target_qf_do_work(),
which is roughly doing:
With multiple CPUs running this code, one CPU can end up deleting the
list entry that the other CPU is about to work on.
Fix this by splicing the list entries onto a local list and then
operating on that in the work function. This way, each invocation of
target_qf_do_work() operates on its own local list and so multiple
invocations don't corrupt each other's list. This also avoids dropping
and reacquiring the lock for each list entry.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Ben Hutchings [Thu, 1 Sep 2011 12:09:59 +0000 (12:09 +0000)]
sfc: Use 64-bit writes for TX push where possible
This was originally done as part of commit 65f0b417dee94f779ce9b77102b7d73c93723b39 ("sfc: Use write-combining to
reduce TX latency"), but that had to be reverted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the processor model, write-combining may result in
reordering that the NIC will not tolerate. This typically results
in a DMA error event and reset by the driver, logged as:
On x86-64, they were just wasteful: with the explicitly added (now
unnecessary) padding, the size of the alternatives structure was 16
bytes, and an alignment of 8 bytes didn't hurt much.
However, it was still silly, since the natural size and alignment for
the structure is actually just 12 bytes, 4-byte aligned since commit 59e97e4d6fbc ("x86: Make alternative instruction pointers relative").
So removing the padding, and removing the extra alignment is just a good
idea.
On x86-32, the alignment of 4 bytes was correct, but was incorrectly
hardcoded as 8 bytes in <asm/alternative-asm.h>. That header file had
used to be an x86-64 only header file, but various unification efforts
have made it be used for x86-32 too (ie the unification of rwlock and
rwsem).
That in turn caused x86-32 boot failures, because the extra alignment
would result in random zero-filled words in the altinstructions section,
causing oopses early at boot when doing alternative instruction
replacement.
So just remove all the alignment noise entirely. It's wrong, and it's
unnecessary. The section itself is already properly aligned by the
linker scripts, and all additions to the section had better be of the
proper 12-byte format, keeping it aligned. So if the align directive
were to ever make a difference, that would be an indication of a serious
bug to begin with.
Reported-by: Werner Landgraf <w.landgraf@ru.r> Acked-by: Andrew Lutomirski <luto@mit.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable changing advertisement settings via ethtool.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Change XMAC loopback type from CORE LOCAL to LINE LOCAL for the BCM578xx due to intermittent problem with the loopback with this configuration.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove remote fault detection as a tactic retreat due to link issues involved with it.
Once issue is resolved, this feature will be restored again.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Enable FEC(Forward Error Correction) for 57810-KR to reduce link errors.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ETS bandwidth of 0% is not allowed by driver, so provide alternative HW configuration for this case.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: Do not allow multiple mounts on same mountpoint when using -o noac
NFS: Fix a typo in nfs_flush_multi
NFSv4: renewd needs to be able to handle the NFS4ERR_CB_PATH_DOWN error
NFSv4: The NFSv4.0 client must send RENEW calls if it holds a delegation
NFSv4: nfs4_proc_renew should be declared static
NFSv4: nfs4_proc_async_renew should use a GFP_NOFS allocation
net: don't clear IFF_XMIT_DST_RELEASE in ether_setup
d88733150 introduced the IFF_SKB_TX_SHARING flag, which I unilaterally set in
ether_setup. In doing this I didn't realize that other flags (such as
IFF_XMIT_DST_RELEASE) might be set prior to calling the ether_setup routine.
This patch changes ether_setup to or in SKB_TX_SHARING so as not to
inadvertently clear other existing flags. Thanks to Pekka Riikonen for pointing
out my error
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Pekka Riikonen <priikone@iki.fi> CC: "David S. Miller" <davem@davemloft.net> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dev_forward_skb loops an skb back into host networking
stack which might hang on the memory indefinitely.
In particular, this can happen in macvtap in bridged mode.
Copy the userspace fragments to avoid blocking the
sender in that case.
As this patch makes skb_copy_ubufs extern now,
I also added some documentation and made it clear
the SKBTX_DEV_ZEROCOPY flag automatically instead
of doing it in all callers. This can be made into a separate
patch if people feel it's worth it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dpward [Wed, 31 Aug 2011 06:05:27 +0000 (06:05 +0000)]
net: Make flow cache namespace-aware
flow_cache_lookup will return a cached object (or null pointer) that the
resolver (i.e. xfrm_policy_lookup) previously found for another namespace
using the same key/family/dir. Instead, make the namespace part of what
identifies entries in the cache.
As before, flow_entry_valid will return 0 for entries where the namespace
has been deleted, and they will be removed from the cache the next time
flow_cache_gc_task is run.
Reported-by: Andrew Dickinson <whydna@whydna.net> Signed-off-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
net/can/af_can.c: Change del_timer to del_timer_sync
This is important for SMP platform to check if timer function is
executing on other CPU with deleting the timer.
Signed-off-by: Rajan Aggarwal <Rajan Aggarwal rajan.aggarwal85@gmail.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:45 +0000 (00:08 +0000)]
bnx2x: don't access removed registers on 57712 and above
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:44 +0000 (00:08 +0000)]
bnx2x: init fw_seq after undi_unload is done
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:43 +0000 (00:08 +0000)]
bnx2x: don't reset device while reading its configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:42 +0000 (00:08 +0000)]
bnx2x: fix MF for 4-port devices
Number of VNs for 4-port devices is 2 instead of 4
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:40 +0000 (00:08 +0000)]
bnx2x: decrease print level to debug
It may happen every link toggle.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log