Fabio Estevam [Mon, 25 Mar 2013 12:20:41 +0000 (09:20 -0300)]
ARM: mach-imx: anatop: Include "common.h"
Fix the following sparse warnings:
arch/arm/mach-imx/anatop.c:56:6: warning: symbol 'imx_anatop_pre_suspend' was not declared. Should it be static?
arch/arm/mach-imx/anatop.c:62:6: warning: symbol 'imx_anatop_post_resume' was not declared. Should it be static?
arch/arm/mach-imx/anatop.c:68:6: warning: symbol 'imx_anatop_usb_chrg_detect_disable' was not declared. Should it be static?
arch/arm/mach-imx/anatop.c:78:5: warning: symbol 'imx_anatop_get_digprog' was not declared. Should it be static?
arch/arm/mach-imx/anatop.c:86:13: warning: symbol 'imx_anatop_init' was not declared. Should it be static?
Anson Huang [Thu, 21 Mar 2013 14:58:06 +0000 (10:58 -0400)]
ARM: imx: enable RBC to support anatop LPM mode
RBC is to control whether some ANATOP sub modules
can enter lpm mode when SOC is into STOP mode, if
RBC is enabled and PMIC_VSTBY_REQ is set, ANATOP
will have below behaviors:
1. Digital LDOs(CORE, SOC and PU) are bypassed;
2. Analog LDOs(1P1, 2P5, 3P0) are disabled;
As the 2P5 is necessary for DRAM IO pre-drive in
STOP mode, so we need to enable weak 2P5 in STOP
mode when 2P5 LDO is disabled.
For RBC settings, there are some rules as below
due to hardware design:
1. All interrupts must be masked during operating
RBC registers;
2. At least 2 CKIL(32K) cycles is needed after the
RBC setting is changed.
Anson Huang [Wed, 20 Mar 2013 23:39:42 +0000 (19:39 -0400)]
ARM: imx: enable anatop suspend/resume
Anatop module have sereval configurations for user
to reduce the power consumption in suspend, provide
suspend/resume interface for further use and enable
fet_odrive to reduce CORE LDO leakage during suspend.
As we have a common anatop file, remove all the operations
of anatop module in other files, use anatop interfaces to
do that.
* Clean up a couple of unneeded function declarations
* Remove imx specific cpufreq driver as generic cpufreq-cpu0 works well
as the replacement
* Remove platform ahci support
* Clean up unused ARCH/MACH Kconfig symbols
* Remove a couple of unused files
* A couple imx35 clock fixes for regressions caused by common clock
framework conversion. The admux and iomux get disabled by common
clock framework late initcall, and hence causes problems.
* Add missing twd clock lookup in device tree. This becomes required
since commit bd60345 (ARM: use device tree to get smp_twd clock)
forces all DT boot to find lookup from device tree.
* Fix imx6q ldb_di clock parents mismatch per reference manual.
Philipp Zabel [Mon, 19 Nov 2012 16:23:13 +0000 (17:23 +0100)]
reset: Add reset controller API
This adds a simple API for devices to request being reset
by separate reset controller hardware and implements the
reset signal device tree binding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Pavel Machek <pavel@ucw.cz>
Stephen Warren [Tue, 23 Oct 2012 21:45:56 +0000 (15:45 -0600)]
dt: describe base reset signal binding
This binding is intended to represent the hardware reset signals present
internally in most IC (SoC, FPGA, ...) designs.
It consists of a binding for a reset controller device (provider), and a
pair of properties, "resets" and "reset-names", to link a device node
(consumer) to its reset controller via phandle, similarly to the clock
and interrupt bindings.
The reset controller has all information necessary to reset the consumer
device. That could be provided via device tree, or it could be implemented
in hardware.
The aim is to enable device drivers to request a framework API to issue a
reset simply by providing their struct device pointer as the most common
case.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Pavel Machek <pavel@ucw.cz> Acked-by: Rob Herring <rob.herring@calxeda.com>
According to the recent i.MX6 Quad technical reference manual, mode 0x4 (100b)
of the CCM_CS2DCR register (address 0x020C402C) bits [11-9] and [14-12] select
the PLL3 clock, and not the PLL3 PFD1 540M clock. In our code, the PLL3 root
clock is named 'pll3_usb_otg', select this instead of the 540M clock.
ARM: imx: provide twd clock lookup from device tree
While booting from device tree, imx6q used to provide twd clock lookup
by calling clk_register_clkdev() in clock driver. However, the commit bd60345 (ARM: use device tree to get smp_twd clock) forces DT boot to
look up the clock from device tree. It causes the failure below when
twd driver tries to get the clock, and hence kernel has to calibrate the
local timer frequency.
smp_twd: clock not found -2
...
Calibrating local timer... 396.13MHz.
Fix the regression by providing twd clock lookup from device tree, and
remove the unused twd clk_register_clkdev() call from clock driver.
Markus Pargmann [Fri, 29 Mar 2013 15:20:10 +0000 (16:20 +0100)]
ARM: imx35 Bugfix admux clock
The admux clock seems to be the audmux clock as tests show. audmux does
not work without this clock enabled. Currently imx35 does not register a
clock device for audmux. This patch adds this registration. imx-audmux
driver already handles a clock device, so no changes are necessary
there.
Markus Pargmann [Fri, 29 Mar 2013 15:20:09 +0000 (16:20 +0100)]
ARM: clk-imx35: Bugfix iomux clock
This patch enables iomuxc_gate clock. It is necessary to be able to
reconfigure iomux pads. Without this clock enabled, the
clk_disable_unused function will disable this clock and the iomux pads
are not configurable anymore. This happens at every boot. After a reboot
(watchdog system reset) the clock is not enabled again, so all iomux pad
reconfigurations in boot code are without effect.
The iomux pads should be always configurable, so this patch always
enables it.
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Two quite small fixes: one a build problem, and the other fixes
seccomp filters on x32."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix rebuild with EFI_STUB enabled
x86: remove the x32 syscall bitmask from syscall_get_nr()
Will Deacon [Sun, 7 Apr 2013 09:36:12 +0000 (21:36 +1200)]
alpha: irq: remove deprecated use of IRQF_DISABLED
Interrupt handlers are always invoked with interrupts disabled, so
remove all uses of the deprecated IRQF_DISABLED flag.
Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Reviewed-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Sun, 7 Apr 2013 09:36:11 +0000 (21:36 +1200)]
alpha: irq: run all handlers with interrupts disabled
Linux has expected that interrupt handlers are executed with local
interrupts disabled for a while now, so ensure that this is the case on
Alpha even for non-device interrupts such as IPIs.
Without this patch, secondary boot results in the following backtrace:
A similar dump occurs if you try to reboot using magic-sysrq.
Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Reviewed-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Sun, 7 Apr 2013 09:36:10 +0000 (21:36 +1200)]
alpha: makefile: don't enforce small data model for kernel builds
Due to all of the goodness being packed into today's kernels, the
resulting image isn't as slim as it once was.
In light of this, don't pass -msmall-data to gcc, which otherwise results
in link failures due to impossible relocations when compiling anything but
the most trivial configurations.
Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Reviewed-by: Matt Turner <mattst88@gmail.com> Tested-by: Thorsten Kranzkowski <dl8bcu@dl8bcu.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Honig [Fri, 29 Mar 2013 16:35:21 +0000 (09:35 -0700)]
KVM: Allow cross page reads and writes from cached translations.
This patch adds support for kvm_gfn_to_hva_cache_init functions for
reads and writes that will cross a page. If the range falls within
the same memslot, then this will be a fast operation. If the range
is split between two memslots, then the slower kvm_read_guest and
kvm_write_guest are used.
Tested: Test against kvm_clock unit tests.
Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Gleb Natapov <gleb@redhat.com>
Merge tag 'dm-3.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper fixes from Alasdair Kergon:
"A pair of patches to fix the writethrough mode of the device-mapper
cache target when the device being cached is not itself wrapped with
device-mapper."
* tag 'dm-3.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm cache: reduce bio front_pad size in writeback mode
dm cache: fix writes to cache device in writethrough mode
Merge tag 'pci-v3.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"PCI updates for v3.9:
ASPM
Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus"
kexec
PCI: Don't try to disable Bus Master on disconnected PCI devices
Platform ROM images
PCI: Add PCI ROM helper for platform-provided ROM images
nouveau: Attempt to use platform-provided ROM image
radeon: Attempt to use platform-provided ROM image
Hotplug
PCI/ACPI: Always resume devices on ACPI wakeup notifications
PCI/PM: Disable runtime PM of PCIe ports
EISA
EISA/PCI: Fix bus res reference
EISA/PCI: Init EISA early, before PNP"
* tag 'pci-v3.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Disable runtime PM of PCIe ports
PCI/ACPI: Always resume devices on ACPI wakeup notifications
PCI: Don't try to disable Bus Master on disconnected PCI devices
Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus"
radeon: Attempt to use platform-provided ROM image
nouveau: Attempt to use platform-provided ROM image
EISA/PCI: Init EISA early, before PNP
EISA/PCI: Fix bus res reference
PCI: Add PCI ROM helper for platform-provided ROM images
1) Fix erroneous sock_orphan() leading to crashes and double
kfree_skb() in NFC protocol. From Thierry Escande and Samuel Ortiz.
2) Fix use after free in remain-on-channel mac80211 code, from Johannes
Berg.
3) nf_reset() needs to reset the NF tracing cookie, otherwise we can
leak it from one namespace into another. Fix from Gao Feng and
Patrick McHardy.
4) Fix overflow in channel scanning array of mwifiex driver, from Stone
Piao.
5) Fix loss of link after suspend/shutdown in r8169, from Hayes Wang.
6) Synchronization of unicast address lists to the undelying device
doesn't work because whether to sync is maintained as a boolean
rather than a true count. Fix from Vlad Yasevich.
7) Fix corruption of TSO packets in atl1e by limiting the segmented
packet length. From Hannes Frederic Sowa.
8) Revert bogus AF_UNIX credential passing change and fix the
coalescing issue properly, from Eric W Biederman.
9) Changes of ipv4 address lifetime settings needs to generate a
notification, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
netfilter: don't reset nf_trace in nf_reset()
net: ipv4: notify when address lifetime changes
ixgbe: fix registration order of driver and DCA nofitication
af_unix: If we don't care about credentials coallesce all messages
Revert "af_unix: dont send SCM_CREDENTIAL when dest socket is NULL"
bonding: remove sysfs before removing devices
atl1e: limit gso segment size to prevent generation of wrong ip length fields
net: count hw_addr syncs so that unsync works properly.
r8169: fix auto speed down issue
netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths
mwifiex: limit channel number not to overflow memory
NFC: microread: Fix build failure due to a new MEI bus API
iwlwifi: dvm: fix the passive-no-RX workaround
netfilter: nf_conntrack: fix error return code
NFC: llcp: Keep the connected socket parent pointer alive
mac80211: fix idle handling sequence
netfilter: nfnetlink_acct: return -EINVAL if object name is empty
netfilter: nfnetlink_queue: fix error return code in nfnetlink_queue_init()
netfilter: reset nf_trace in nf_reset
mac80211: fix remain-on-channel cancel crash
...
Jan Beulich [Wed, 3 Apr 2013 14:47:33 +0000 (15:47 +0100)]
x86: Fix rebuild with EFI_STUB enabled
eboot.o and efi_stub_$(BITS).o didn't get added to "targets", and hence
their .cmd files don't get included by the build machinery, leading to
the files always getting rebuilt.
Rather than adding the two files individually, take the opportunity and
add $(VMLINUX_OBJS) to "targets" instead, thus allowing the assignment
at the top of the file to be shrunk quite a bit.
At the same time, remove a pointless flags override line - the variable
assigned to was misspelled anyway, and the options added are
meaningless for assembly sources.
[ hpa: the patch is not minimal, but I am taking it for -urgent anyway
since the excess impact of the patch seems to be small enough. ]
Patrick McHardy [Fri, 5 Apr 2013 18:42:05 +0000 (20:42 +0200)]
netfilter: don't reset nf_trace in nf_reset()
Commit 130549fe ("netfilter: reset nf_trace in nf_reset") added code
to reset nf_trace in nf_reset(). This is wrong and unnecessary.
nf_reset() is used in the following cases:
- when passing packets up the the socket layer, at which point we want to
release all netfilter references that might keep modules pinned while
the packet is queued. nf_trace doesn't matter anymore at this point.
- when encapsulating or decapsulating IPsec packets. We want to continue
tracing these packets after IPsec processing.
- when passing packets through virtual network devices. Only devices on
that encapsulate in IPv4/v6 matter since otherwise nf_trace is not
used anymore. Its not entirely clear whether those packets should
be traced after that, however we've always done that.
- when passing packets through virtual network devices that make the
packet cross network namespace boundaries. This is the only cases
where we clearly want to reset nf_trace and is also what the
original patch intended to fix.
Add a new function nf_reset_trace() and use it in dev_forward_skb() to
fix this properly.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Fixes for a number of small glitches in various corners of the MIPS
tree. No particular areas is standing out.
With this applied all MIPS defconfigs are building fine. No merge
conflicts are expected."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Delete definition of SA_RESTORER.
MIPS: Fix ISA level which causes secondary cache init bypassing and more
MIPS: Fix build error cavium-octeon without CONFIG_SMP
MIPS: Kconfig: Rename SNIPROM too
MIPS: Alchemy: Fix typo "CONFIG_DEBUG_PCI"
MIPS: Unbreak function tracer for 64-bit kernel.
Pull GFS2 fixes from Steven Whitehouse:
"There are two patches which fix up a couple of minor issues in the DLM
interface code, a missing error path in gfs2_rs_alloc(), one patch
which fixes a problem during "withdraw" and a fix for discards/FITRIM
when using 4k sector sized devices."
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Issue discards in 512b sectors
GFS2: Fix unlock of fcntl locks during withdrawn state
GFS2: return error if malloc failed in gfs2_rs_alloc()
GFS2: use memchr_inv
GFS2: use kmalloc for lvb bitmap
Merge tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi fixes from Mark Brown:
"A bunch of small driver fixes plus a fix for error handling in the
core - nothing too exciting overall."
* tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/mpc512x-psc: optionally keep PSC SS asserted across xfer segmensts
spi: Unlock a spinlock before calling into the controller driver.
spi/s3c64xx: modified error interrupt handling and init
spi/bcm63xx: don't disable non enabled clocks in probe error path
spi/bcm63xx: Remove unused variable
spi: slink-tegra20: move runtime pm calls to transfer_one_message
Bob Peterson [Fri, 22 Mar 2013 14:07:24 +0000 (10:07 -0400)]
GFS2: Issue discards in 512b sectors
This patch changes GFS2's discard issuing code so that it calls
function sb_issue_discard rather than blkdev_issue_discard. The
code was calling blkdev_issue_discard and specifying the correct
sector offset and sector size, but blkdev_issue_discard expects
these values to be in terms of 512 byte sectors, even if the native
sector size for the device is different. Calling sb_issue_discard
with the BLOCK size instead ensures the correct block-to-512b-sector
translation. I verified that "minlen" is specified in blocks, so
comparing it to a number of blocks is correct.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch introduced a few races which cannot be easily fixed with a
small follow-up patch. Furthermore, the SoC with the broken hardware
register, which this patch intended to add support for, can only be used
with device trees, which this driver currently does not support.
[ Here is the discussion that led to this "revert" patch:
https://lkml.org/lkml/2013/4/3/176 ]
Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'fbdev-fixes-3.9-rc6' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev fixes from Tomi Valkeinen:
"Fix uvesafb crash bug and typoed flag name in fbmon's new videomode
code"
* tag 'fbdev-fixes-3.9-rc6' of git://gitorious.org/linux-omap-dss2/linux:
video:uvesafb: Fix dereference NULL pointer code path
fbmon: use VESA_DMT_VSYNC_HIGH to fix typo
Merge tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains slightly more volumes than usual at this stage, mostly
because of my vacation in the last week. Nothing to scare, all small
and/or trivial fixes:
- Fix loop path handling in ASoC DAPM
- Some memory handling fixes in ASoC core
- Fix spear_pcm to adapt to the updated API
- HD-audio HDMI ELD handling fixes
- Fix for CM6331 USB-audio SRC change bugs
- Revert power_save_controller option change due to user-space usage
- A few other small ASoC and HD-audio fixes"
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/generic - fix uninitialized variable
Revert "ALSA: hda - Allow power_save_controller option override DCAPS"
ALSA: hda - fix typo in proc output
ALSA: hda - Enabling Realtek ALC 671 codec
ALSA: usb: Work around CM6631 sample rate change bug
ALSA: hda - bug fix on HDMI ELD debug message
ALSA: hda - bug fix on return value when getting HDMI ELD info
ASoC: dma-sh7760: Fix compile error
ASoC: core: fix invalid free of devm_ allocated data
ASoC: spear_pcm: Update to new pcm_new() API
ASoC:: max98090: Remove executable bit
ASoC: dapm: Fix pointer dereference in is_connected_output_ep()
ASoC: pcm030 audio fabric: remove __init from probe
ASoC: imx-ssi: Fix occasional AC97 reset failure
ASoC: core: fix possible memory leak in snd_soc_bytes_put()
ASoC: wm_adsp: fix possible memory leak in wm_adsp_load_coeff()
ASoC: dapm: Fix handling of loops
ASoC: si476x: Add missing break for SNDRV_PCM_FORMAT_S8 switch case
Mike Snitzer [Fri, 5 Apr 2013 14:36:34 +0000 (15:36 +0100)]
dm cache: reduce bio front_pad size in writeback mode
A recent patch to fix the dm cache target's writethrough mode extended
the bio's front_pad to include a 1056-byte struct dm_bio_details.
Writeback mode doesn't need this, so this patch reduces the
per_bio_data_size to 16 bytes in this case instead of 1096.
The dm_bio_details structure was added in "dm cache: fix writes to
cache device in writethrough mode" which fixed commit e2e74d617e ("dm
cache: fix race in writethrough implementation"). In writeback mode
we avoid allocating the writethrough-specific members of the
per_bio_data structure (the dm_bio_details structure included).
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Darrick J. Wong [Fri, 5 Apr 2013 14:36:32 +0000 (15:36 +0100)]
dm cache: fix writes to cache device in writethrough mode
The dm-cache writethrough strategy introduced by commit e2e74d617eadc15
("dm cache: fix race in writethrough implementation") issues a bio to
the origin device, remaps and then issues the bio to the cache device.
This more conservative in-series approach was selected to favor
correctness over performance (of the previous parallel writethrough).
However, this in-series implementation that reuses the same bio to write
both the origin and cache device didn't take into account that the block
layer's req_bio_endio() modifies a completing bio's bi_sector and
bi_size. So the new writethrough strategy needs to preserve these bio
fields, and restore them before submission to the cache device,
otherwise nothing gets written to the cache (because bi_size is 0).
This patch adds a struct dm_bio_details field to struct per_bio_data,
and uses dm_bio_record() and dm_bio_restore() to ensure the bio is
restored before reissuing to the cache device. Adding such a large
structure to the per_bio_data is not ideal but we can improve this
later, for now correctness is the important thing.
This problem initially went unnoticed because the dm-cache test-suite
uses a linear DM device for the dm-cache device's origin device.
Writethrough worked as expected because DM submits a *clone* of the
original bio, so the original bio which was reused for the cache was
never touched.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Ralf Baechle [Mon, 25 Mar 2013 12:43:14 +0000 (13:43 +0100)]
MIPS: Delete definition of SA_RESTORER.
SA_RESTORER used to be defined as 0x04000000 but only the O32 ABI ever
supported its use and no libc was using it, so the entire sa-restorer
functionality was removed with lmo commit 39bffc12c3580ab [Zap sa_restorer.]
for 2.5.48 retaining only the SA_RESTORER definition as a reminder to avoid
accidental reuse of the mask bit.
Upstream cdef9602fbf1871a43f0f1b5cea10dd0f275167d [signal: always clear
sa_restorer on execve] adds code that assumes sa_sigaction has an
sa_restorer field, if SA_RESTORER is defined which would break MIPS.
So remove the SA_RESTORER definition before the v3.8.4 merge.
MIPS: Fix ISA level which causes secondary cache init bypassing and more
The commit a96102be70 introduced set_isa() where compatible ISA info is
also set aside from the one gets passed in. It means, for example, 1004K
will have MIPS_CPU_ISA_M32R2/M32R1/II/I flags. This leads to things like
the following inappropriate:
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Bolle [Thu, 4 Apr 2013 12:47:01 +0000 (12:47 +0000)]
MIPS: Alchemy: Fix typo "CONFIG_DEBUG_PCI"
Commit 7517de348663b08a808aff44b5300e817157a568 ("MIPS: Alchemy: Redo
PCI as platform driver") added a reference to CONFIG_DEBUG_PCI. Change
it to CONFIG_PCI_DEBUG, as that is a valid Kconfig macro.
Also add a newline to a debugging printk that this fix enables.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 2 Apr 2013 22:59:29 +0000 (22:59 +0000)]
MIPS: Unbreak function tracer for 64-bit kernel.
Commit 58b69401c797 [MIPS: Function tracer: Fix broken function tracing]
completely broke the function tracer for 64-bit kernels. The symptom is
a system hang very early in the boot process.
The fix: Remove/fix $sp adjustments for 64-bit case.
Signed-off-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: Al Cooper <alcooperx@gmail.com> Cc: viric@viric.name Cc: stable@vger.kernel.org # 3.8.x Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jakub Kicinski [Wed, 3 Apr 2013 16:50:54 +0000 (16:50 +0000)]
ixgbe: fix registration order of driver and DCA nofitication
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: If we don't care about credentials coallesce all messages
It was reported that the following LSB test case failed
https://lsbbugs.linuxfoundation.org/attachment.cgi?id=2144 because we
were not coallescing unix stream messages when the application was
expecting us to.
The problem was that the first send was before the socket was accepted
and thus sock->sk_socket was NULL in maybe_add_creds, and the second
send after the socket was accepted had a non-NULL value for sk->socket
and thus we could tell the credentials were not needed so we did not
bother.
The unnecessary credentials on the first message cause
unix_stream_recvmsg to start verifying that all messages had the same
credentials before coallescing and then the coallescing failed because
the second message had no credentials.
Ignoring credentials when we don't care in unix_stream_recvmsg fixes a
long standing pessimization which would fail to coallesce messages when
reading from a unix stream socket if the senders were different even if
we did not care about their credentials.
I have tested this and verified that the in the LSB test case mentioned
above that the messages do coallesce now, while the were failing to
coallesce without this change.
Reported-by: Karel Srot <ksrot@redhat.com> Reported-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The problem that the above patch was meant to address is that af_unix
messages are not being coallesced because we are sending unnecesarry
credentials. Not sending credentials in maybe_add_creds totally
breaks unconnected unix domain sockets that wish to send credentails
to other sockets.
In practice this break some versions of udev because they receive a
message and the sending uid is bogus so they drop the message.
Reported-by: Sven Joachim <svenjoac@gmx.de> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We have a race condition if we try to rmmod bonding and simultaneously add
a bond master through sysfs. In bonding_exit() we first remove the devices
(through rtnl_link_unregister() ) and only after that we remove the sysfs.
If we manage to add a device through sysfs after that the devices were
removed - we'll end up with that device/sysfs structure and with the module
unloaded.
Fix this by first removing the sysfs and only after that calling
rtnl_link_unregister().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atl1e: limit gso segment size to prevent generation of wrong ip length fields
The limit of 0x3c00 is taken from the windows driver.
Suggested-by: Huang, Xiong <xiong@qca.qualcomm.com> Cc: Huang, Xiong <xiong@qca.qualcomm.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: count hw_addr syncs so that unsync works properly.
A few drivers use dev_uc_sync/unsync to synchronize the
address lists from master down to slave/lower devices. In
some cases (bond/team) a single address list is synched down
to multiple devices. At the time of unsync, we have a leak
in these lower devices, because "synced" is treated as a
boolean and the address will not be unsynced for anything after
the first device/call.
Treat "synced" as a count (same as refcount) and allow all
unsync calls to work.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'pm+acpi-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Revert of a recent cpuidle change that caused Nehalem machines to
hang on boot from Alex Shi.
- USB power management fix addressing a crash in the port device
object's release routine from Rafael J Wysocki.
- Device PM QoS fix for a potential deadlock related to sysfs interface
from Rafael J Wysocki.
- Fix for a cpufreq crash when the /cpus Device Tree node is missing
from Paolo Pisati.
- Fix for a build issue on ia64 related to the Boot Graphics Resource
Table (BGRT) from Tony Luck.
- Two fixes for ACPI handles being set incorrectly for device objects
that don't correspond to any ACPI namespace nodes in the I2C and SPI
subsystems from Rafael J Wysocki.
- Fix for compiler warnings related to CONFIG_PM_DEVFREQ being unset
from Rajagopal Venkat.
- Fix for a symbol definition typo in cpufreq_governor.h from Borislav
Petkov.
* tag 'pm+acpi-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / BGRT: Don't let users configure BGRT on non X86 systems
cpuidle / ACPI: recover percpu ACPI processor cstate
ACPI / I2C: Use parent's ACPI_HANDLE() in acpi_i2c_register_devices()
cpufreq: Correct header guards typo
ACPI / SPI: Use parent's ACPI_HANDLE() in acpi_register_spi_devices()
cpufreq: check OF node /cpus presence before dereferencing it
PM / devfreq: Fix compiler warnings for CONFIG_PM_DEVFREQ unset
PM / QoS: Avoid possible deadlock related to sysfs access
USB / PM: Don't try to hide PM QoS flags from usb_port_device_release()
hayeswang [Sun, 31 Mar 2013 17:02:04 +0000 (17:02 +0000)]
r8169: fix auto speed down issue
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Apr 2013 21:39:06 +0000 (17:39 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into wireless
John W. Linville says:
====================
Here are some more fixes intended for the 3.9 stream...
Regarding the mac80211 bits, Johannes says:
"I had changed the idle handling to simplify it, but broken the
sequencing of commands, at least for ath9k-htc, one patch restores the
sequence. The other patch fixes a crash Jouni found while stress-testing
the remain-on-channel code, when an item is deleted the work struct can
run twice and crash the second time."
As for the iwlwifi bits, Johannes says:
"The only fix here is to the passive-no-RX firmware regulatory
enforcement driver support code to not drop auth frames in quick
succession, leading to not being able to connect to APs on passive
channels in certain circumstances."
Don't forget the NFC bits, about which Samuel says:
"This time we have:
- A crash fix for when a DGRAM LLCP socket is listening while the NFC adapter
is physically removed.
- A potential double skb free when the LLCP socket receive queue is full.
- A fix for properly handling multiple and consecutive LLCP connections, and
not trash the socket ack log.
- A build failure for the MEI microread physical layer, now that the MEI bus
APIs have been merged into char-misc-next."
On top of that, Stone Piao provides an mwifiex fix to avoid accessing
beyond the end of a buffer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Stancek [Thu, 4 Apr 2013 18:35:10 +0000 (11:35 -0700)]
mm: prevent mmap_cache race in find_vma()
find_vma() can be called by multiple threads with read lock
held on mm->mmap_sem and any of them can update mm->mmap_cache.
Prevent compiler from re-fetching mm->mmap_cache, because other
readers could update it in the meantime:
thread 1 thread 2
|
find_vma() | find_vma()
struct vm_area_struct *vma = NULL; |
vma = mm->mmap_cache; |
if (!(vma && vma->vm_end > addr |
&& vma->vm_start <= addr)) { |
| mm->mmap_cache = vma;
return vma; |
^^ compiler may optimize this |
local variable out and re-read |
mm->mmap_cache |
This issue can be reproduced with gcc-4.8.0-1 on s390x by running
mallocstress testcase from LTP, which triggers:
Merge tag 'upstream-3.9-rc6' of git://git.infradead.org/linux-ubifs
Pull UBIFS fix from Artem Bityutskiy:
"Make the space fixup feature work in the case when the file-system is
first mounted R/O and then remounted R/W."
* tag 'upstream-3.9-rc6' of git://git.infradead.org/linux-ubifs:
UBIFS: make space fixup work in the remount case
* pm-fixes:
cpufreq: Correct header guards typo
cpufreq: check OF node /cpus presence before dereferencing it
PM / devfreq: Fix compiler warnings for CONFIG_PM_DEVFREQ unset
PM / QoS: Avoid possible deadlock related to sysfs access
USB / PM: Don't try to hide PM QoS flags from usb_port_device_release()
* acpi-fixes:
ACPI / BGRT: Don't let users configure BGRT on non X86 systems
cpuidle / ACPI: recover percpu ACPI processor cstate
ACPI / I2C: Use parent's ACPI_HANDLE() in acpi_i2c_register_devices()
ACPI / SPI: Use parent's ACPI_HANDLE() in acpi_register_spi_devices()
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- Workaround for device ID conflict between Masterkit MA901 usb radio
device and Atmel V-USB devices, to avoid regressions from older
kernels, by Alexey Klimov
- fix for possible race during input device registration in magicmouse
driver, by Benjamin Tissoires
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: magicmouse: fix race between input_register() and probe()
media: radio-ma901: return ENODEV in probe if usb_device doesn't match
HID: fix Masterkit MA901 hid quirks
Merge tag 'gpio-fixes-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes for the v3.9 series:
- Fix erroneous return value in the ICH driver
- Make the STMPE driver proper properly on device tree boots"
* tag 'gpio-fixes-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: stmpe: pass DT node to irqdomain
gpio-ich: Fix value returned by ichx_gpio_request
The commit [6ab317419c: ALSA: hda - Allow power_save_controller option
override DCAPS] changed the behavior of power_save_controller so that
it can override the driver capability. This assumed that this option
is rarely changed dynamically unlike power_save option. Too naive.
It turned out that the user-space power-management tool tries to set
power_save_controller option to 1 together with power_save option
without knowing what's actually doing. This enabled forcibly the
runtime PM of the controller, which is known to be broken om many
chips thus disabled as default.
So, the only sane fix is to revert this commit again. It was intended
to ease debugging/testing for runtime PM enablement, but obviously we
need another way for it.
GFS2: Fix unlock of fcntl locks during withdrawn state
When withdraw occurs, we need to continue to allow unlocks of fcntl
locks to occur, however these will only be local, since the node has
withdrawn from the cluster. This prevents triggering a VFS level
bug trap due to locks remaining when a file is closed.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
HID: magicmouse: fix race between input_register() and probe()
Since kernel 3.7, it appears that the input registration occured before
the end of magicmouse_setup_input(). This is shown by receiving a lot of
"EV_SYN SYN_REPORT 1" instead of normal "EV_SYN SYN_REPORT 0".
This value means that the output buffer is full, and the user space
is loosing events.
Using .input_configured guarantees that the race is not occuring, and that
the call of "input_set_events_per_packet(input, 60)" is taken into account
by input_register().
* Added the device ID to the modalias list and assinged ALC662 patches
for it
* Added 4 port support for the device ID 0671 in alc662_parse_auto_config
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Another round of ARM fixes, which include:
- Fixing a problem with LPAE mapping sections
- Reporting of some hwcaps on Krait CPUs
- Avoiding repetitive warnings in the breakpoint code
- Fixing a build error noticed on Dove platforms with PJ4 CPUs
- Fix masking of level 2 cache revision.
- Fixing timer-based udelay()
- A larger fix for an erratum causing people major grief with Cortex
A15 CPUs"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7690/1: mm: fix CONFIG_LPAE typos
ARM: 7689/1: add unwind annotations to ftrace asm
ARM: 7685/1: delay: use private ticks_per_jiffy field for timer-based delay ops
ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)
ARM: 7682/1: cache-l2x0: fix masking of RTL revision numbering and set_debug init
ARM: iWMMXt: always enable iWMMXt support with PJ4 CPUs
ARM: 7681/1: hw_breakpoint: use warn_once to avoid spam from reset_ctrl_regs()
ARM: 7678/1: Work around faulty ISAR0 register in some Krait CPUs
ARM: 7680/1: Detect support for SDIV/UDIV from ISAR0 register
ARM: 7679/1: Clear IDIVT hwcap if CONFIG_ARM_THUMB=n
ARM: 7677/1: LPAE: Fix mapping in alloc_init_section for unaligned addresses
ARM: KVM: vgic: take distributor lock on sync_hwstate path
ARM: KVM: vgic: force EOIed LRs to the empty state
The runtime PM of PCIe ports turns out to be quite fragile, as in
some cases things work while in some other cases they don't and we
don't seem to have a good way to determine whether or not they are
going to work in advance.
For this reason, avoid enabling runtime PM for PCIe ports by
keeping their runtime PM reference counters always above 0 for the
time being.
When a PCIe port is suspended, it can no longer report events like
hotplug, so hotplug below the port may not work, as in the bug
report below.
[bhelgaas: changelog, stable]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53811 Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.6+
PCI/ACPI: Always resume devices on ACPI wakeup notifications
It turns out that the _Lxx control methods provided by some BIOSes
clear the PME Status bit of PCI devices they handle, which means that
pci_acpi_wake_dev() cannot really use that bit to check whether or
not the device has signalled wakeup.
One symptom of the problem is, for example, that when an affected PCI
USB controller is runtime-suspended, then plugging in a new USB device
into one of the controller's ports will not wake up the controller,
which should happen.
For this reason, make pci_acpi_wake_dev() always attempt to resume
the device it is called for regardless of the device's PME Status bit
value (that bit still has to be cleared if set at this point,
though).
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Matthew Garrett <mjg59@srcf.ucam.org> CC: stable@vger.kernel.org # v3.7+
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Unfortunately, we introduced some big-endian bugs during the last
merge window. Fortunately, Cai and Christian noticed before 3.9
shipped."
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix big-endian bugs which could cause fs corruptions
Zheng Liu [Wed, 3 Apr 2013 16:27:18 +0000 (12:27 -0400)]
ext4: fix big-endian bugs which could cause fs corruptions
When an extent was zeroed out, we forgot to do convert from cpu to le16.
It could make us hit a BUG_ON when we try to write dirty pages out. So
fix it.
[ Also fix a bug found by Dmitry Monakhov where we were missing
le32_to_cpu() calls in the new indirect punch hole code.
There are a number of other big endian warnings found by static code
analyzers, but we'll wait for the next merge window to fix them all
up. These fixes are designed to be Obviously Correct by code
inspection, and easy to demonstrate that it won't make any
difference (and hence, won't introduce any bugs) on little endian
architectures such as x86. --tytso ]
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reported-by: CAI Qian <caiqian@redhat.com> Reported-by: Christian Kujau <lists@nerdbynature.de> Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Paul Bolle [Wed, 3 Apr 2013 11:24:45 +0000 (12:24 +0100)]
ARM: 7690/1: mm: fix CONFIG_LPAE typos
CONFIG_LPAE doesn't exist: the correct option is CONFIG_ARM_LPAE, so fix
up the two typos under arch/arm/.
The fix to head.S is slightly scary, but this is just for setting up
an early io-mapping for the serial port when running on a big-endian,
LPAE system. Since these systems don't exist in the wild (at least, I
have no access to one outside of kvmtool, which doesn't provide a serial
port suitable for earlyprintk), then we can revisit the code later if it
causes any problems.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rabin Vincent [Tue, 2 Apr 2013 21:11:46 +0000 (22:11 +0100)]
ARM: 7689/1: add unwind annotations to ftrace asm
Add unwind annotations to the ftrace assembly code so that the function
tracer's stacktracing options (func_stack_trace, etc.) work when
CONFIG_ARM_UNWIND is enabled.
Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 28 Mar 2013 10:17:55 +0000 (11:17 +0100)]
ARM: 7685/1: delay: use private ticks_per_jiffy field for timer-based delay ops
Commit 70264367a243 ("ARM: 7653/2: do not scale loops_per_jiffy when
using a constant delay clock") fixed a problem with our timer-based
delay loop, where loops_per_jiffy is scaled by cpufreq yet used directly
by the timer delay ops.
This patch fixes the problem in a more elegant way by keeping a private
ticks_per_jiffy field in the delay ops, independent of loops_per_jiffy
and therefore not subject to scaling. The loop-based delay continues to
use loops_per_jiffy directly, as it should.
Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Tue, 26 Mar 2013 22:35:04 +0000 (23:35 +0100)]
ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)
On Cortex-A15 (r0p0..r3p2) the TLBI/DSB are not adequately shooting down
all use of the old entries. This patch implements the erratum workaround
which consists of:
1. Dummy TLBIMVAIS and DSB on the CPU doing the TLBI operation.
2. Send IPI to the CPUs that are running the same mm (and ASID) as the
one being invalidated (or all the online CPUs for global pages).
3. CPU receiving the IPI executes a DMB and CLREX (part of the exception
return code already).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rob Herring [Mon, 25 Mar 2013 16:02:48 +0000 (17:02 +0100)]
ARM: 7682/1: cache-l2x0: fix masking of RTL revision numbering and set_debug init
Commit b8db6b8 (ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache
ctrl) moved the masking of the part ID which caused the RTL version to be
lost. Commit 6248d06 (ARM: 7545/1: cache-l2x0: make outer_cache_fns a
field of l2x0_of_data) changed how .set_debug is initialized. Both commits
break commit 74ddcdb (ARM: 7608/1: l2x0: Only set .set_debug
on PL310 r3p0 and earlier) which uses the RTL version to conditionally set
.set_debug function pointer. Commit b8db6b8 also caused the printed cache
ID to be missing the version information.
Fix this by reverting how the part number is masked so the RTL version
info is maintained. The cache-id-part DT property does not set the RTL
bits so masking them should have no effect. Also, re-arrange the order
of the function pointer init so the .set_debug function can be overridden.
Reported-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Yehuda Yitschak <yehuday@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 3 Apr 2013 15:33:26 +0000 (16:33 +0100)]
ARM: iWMMXt: always enable iWMMXt support with PJ4 CPUs
Jason Cooper reports these build errors:
arch/arm/kernel/built-in.o: In function `iwmmxt_do':
/.../arch/arm/kernel/pj4-cp0.c:36: undefined reference to `iwmmxt_task_release'
/.../arch/arm/kernel/pj4-cp0.c:40: undefined reference to `iwmmxt_task_switch'
make: *** [vmlinux] Error 1
This is caused because the PJ4 code explicitly references the iWMMXt
code, but doesn't require it to be built. Fix this by ensuring that
iWMMXt is always enabled with PJ4.
Reported-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Torstein Hegge [Tue, 26 Mar 2013 21:10:05 +0000 (22:10 +0100)]
ALSA: usb: Work around CM6631 sample rate change bug
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Tony Luck [Wed, 3 Apr 2013 11:17:20 +0000 (13:17 +0200)]
ACPI / BGRT: Don't let users configure BGRT on non X86 systems
Fengguang Wu's 0-Day kernel build testing backend found the
following build error for an allmodconfig build on ia64:
drivers/built-in.o: In function `show_yoffset':
>> bgrt.c:(.text+0xe5a71): undefined reference to `bgrt_tab'
>> bgrt.c:(.text+0xe5a91): undefined reference to `bgrt_tab'
drivers/built-in.o: In function `show_xoffset':
>> bgrt.c:(.text+0xe5b51): undefined reference to `bgrt_tab'
>> bgrt.c:(.text+0xe5b71): undefined reference to `bgrt_tab'
drivers/built-in.o: In function `show_type':
>> bgrt.c:(.text+0xe5c31): undefined reference to `bgrt_tab'
drivers/built-in.o:bgrt.c:(.text+0xe5c51): more undefined references to `bgrt_tab' follow
drivers/built-in.o: In function `bgrt_init':
bgrt.c:(.init.text+0x8931): undefined reference to `bgrt_image'
bgrt.c:(.init.text+0x8932): undefined reference to `bgrt_image_size'
bgrt.c:(.init.text+0x8950): undefined reference to `bgrt_image'
bgrt.c:(.init.text+0x8960): undefined reference to `bgrt_image_size'
The problem is that all these undefined names are provided by
arch/x86/platform/efi/efi-bgrt.c - which is obviously not available
to the ia64 build.
It doesn't seem useful to provide the BGRT support for Itanium
(many systems are headless and have no graphics at all). So
just don't let users configure this driver on non-X86 machines.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths
The bitmask used for the prefix mangling was being calculated
incorrectly, leading to the wrong part of the address being replaced
when the prefix length wasn't a multiple of 32.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
1) Fix VSOCK layer handling of context ID changes, from Reilly Grant.
2) Now that we have a synchronize_net() in netdev_rx_handler_unregister(),
we can't let any call sites hold locks. Unfortunately bonding does,
so we have to drop the rwlock there a little bit earlier, fix from
Veaceslav Falico.
3) MAC address setting loop exits one iteration too early in mlx4
driver, from Yan Burman.
4) Restore ipv6 routes properly upon ifdown/ifup of loopback, from
Balakumaran Kannan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
VSOCK: Handle changes to the VMCI context ID.
net IPv6 : Fix broken IPv6 routing table after loopback down-up
cbq: incorrect processing of high limits
net/mlx4_en: Fix setting initial MAC address
bonding: get netdev_rx_handler_unregister out of locks
Merge tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A small collection of fixes. The most important ones are those from
Stephen and Lars-Peter both of which fix cache issues that have been
lurking for a while but not manifesting noticably enough for anyone to
report them."
* tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: async: Add missing return
regmap: don't corrupt work buffer in _regmap_raw_write()
regmap: cache Fix regcache-rbtree sync
regmap: Initialize `map->debugfs' before regcache
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull DRM fixes from Dave Airlie:
"Two core fixes, both regressions, along with some intel and some
nouveau fixes for regressions and oopses"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: correctly restore mappings if drm_open fails
drm/nouveau: fix NULL ptr dereference from nv50_disp_intr()
drm/nouveau: fix handling empty channel list in ioctl's
drm: don't unlock in the addfb error paths
drm/i915: Fix build failure
drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
drm/i915: duct-tape locking when eDP init fails
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A collection of fixes pretty much across the MIPS code. Even the
change to include/linux/signal.h by David Howells' 2a1486981c13 ("Fix
breakage in MIPS siginfo handling") should be considered MIPS-specific
as it touches an ifdefed segment that is only relevant to MIPS and
which unfortunately can't be made to go away entirely."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Fix breakage in MIPS siginfo handling
Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()"
MIPS: BCM63XX: Make nvram checksum failure non fatal
MIPS: Fix code generation for non-DSP capable CPUs
MIPS: Fix inconsistent formatting inside /proc/cpuinfo
MIPS: SEAD3: Enable LL/SC.
MIPS: Get rid of CONFIG_CPU_HAS_LLSC again
MIPS: Add dependencies for HAVE_ARCH_TRANSPARENT_HUGEPAGE
MIPS: VR4133: Fix probe for LL/SC.
MIPS: Fix logic errors in bitops.c
MIPS: Use CONFIG_CPU_MIPSR2 in csum_partial.S
MIPS: compat: Return same error ENOSYS as native for invalid operation.
PCI: Don't try to disable Bus Master on disconnected PCI devices
This is a fix for commit 7897e60227 ("PCI: Disable Bus Master
unconditionally in pci_device_shutdown()"). Vivek reported that
with this commit, kexec failed because none of his SATA disks
came up.
A ->shutdown() callback might put the device in D3cold, which means config
space is no longer available.
[bhelgaas: changelog] Link: https://lkml.org/lkml/2013/3/12/529 Reported-and-Tested-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit broke some pre-1.1 PCIe devices by leaving them with
ASPM enabled. Previously, we had disabled ASPM on these devices
because many of them don't implement it correctly (per 149e1637).
Requesting _OSC control early means that aspm_disabled may be set
before we scan the PCI bus and configure link ASPM state. But the
ASPM configuration currently skips the check for pre-PCIe 1.1 devices
when aspm_disabled is set, like this:
acpi_pci_root_add
acpi_pci_osc_support
if (flags != base_flags)
pcie_no_aspm
aspm_disabled = 1
pci_acpi_scan_root
...
pcie_aspm_init_link_state
pcie_aspm_sanity_check
if (!aspm_disabled)
/* check for pre-PCIe 1.1 device */
Therefore, setting aspm_disabled early means that we leave ASPM enabled
on these pre-PCIe 1.1 devices, which is a regression for some devices.
The best fix would be to clean up the ASPM init so we can evaluate
_OSC before scanning the bug (that way boot-time and hot-add discovery
will work the same), but that requires significant rework.
For now, we'll just revert the _OSC change as the lowest-risk fix.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=55211 Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> CC: stable@vger.kernel.org # v3.8+
Paul Moore [Fri, 15 Feb 2013 17:21:43 +0000 (12:21 -0500)]
x86: remove the x32 syscall bitmask from syscall_get_nr()
Commit fca460f95e928bae373daa8295877b6905bc62b8 simplified the x32
implementation by creating a syscall bitmask, equal to 0x40000000, that
could be applied to x32 syscalls such that the masked syscall number
would be the same as a x86_64 syscall. While that patch was a nice
way to simplify the code, it went a bit too far by adding the mask to
syscall_get_nr(); returning the masked syscall numbers can cause
confusion with callers that expect syscall numbers matching the x32
ABI, e.g. unmasked syscall numbers.
This patch fixes this by simply removing the mask from syscall_get_nr()
while preserving the other changes from the original commit. While
there are several syscall_get_nr() callers in the kernel, most simply
check that the syscall number is greater than zero, in this case this
patch will have no effect. Of those remaining callers, they appear
to be few, seccomp and ftrace, and from my testing of seccomp without
this patch the original commit definitely breaks things; the seccomp
filter does not correctly filter the syscalls due to the difference in
syscall numbers in the BPF filter and the value from syscall_get_nr().
Applying this patch restores the seccomp BPF filter functionality on
x32.
I've tested this patch with the seccomp BPF filters as well as ftrace
and everything looks reasonable to me; needless to say general usage
seemed fine as well.
Signed-off-by: Paul Moore <pmoore@redhat.com> Link: http://lkml.kernel.org/r/20130215172143.12549.10292.stgit@localhost Cc: <stable@vger.kernel.org> Cc: Will Drewry <wad@chromium.org> Cc: H. Peter Anvin <hpa@zytor.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If first drm_open fails, the error-handling path will
incorrectly restore inode's mapping to NULL. This can
cause the crash later on. Fix by separately storing
away mapping pointers that drm_open can touch and
restore each from its own respective variable if the
call fails.
Fixes: https://bugzilla.novell.com/show_bug.cgi?id=807850
(thanks to Michal Hocko for investigating investigating and
finding the root cause of the bug)
projects / linux-beck.git / log