Michal Simek [Tue, 22 Jun 2010 15:46:27 +0000 (17:46 +0200)]
microblaze: Implement clear_ums macro and fix SAVE_STATE macro
VMS is always setup because VM mode was before
exception/syscall/interrupt. Kernel continues in kernel mode
that's why we have to clear UMS bit if kernel comes from
user space.
Michal Simek [Tue, 22 Jun 2010 14:39:56 +0000 (16:39 +0200)]
microblaze: Remove additional setup for kernel_mode
PT_MODE stores information if kernel comes from user
or kernel space. If come from user space, PT_MODE
contains 0. If come from kernel store, PT_MODE contains
non zero value. We don't need to save value 1. I am using
r1 register which contains non zero value.
This change save one additional instruction.
Michal Simek [Tue, 22 Jun 2010 13:25:24 +0000 (15:25 +0200)]
microblaze: Simplify _debug_exception function
Keep together all arguments for send_sig function.
Move returning address to delay slot which is executed.
Remove additional send_sig loading. I am using IMM part of
rtbd instruction with r0.
old solution:
addik r11, r0, send_sig
rtbd r11, 0
nop
Michal Simek [Thu, 17 Jun 2010 14:03:05 +0000 (16:03 +0200)]
microblaze: Optimize SAVE_STATE macro
It is necessary to setup BIP and EE and clear EIP
only for unaligned exception handler. The rest of
hw exception handlers don't require it.
HW exception occured and we are not in virtual mode.
That's why we can do operations protected by EIP.
Interrupt, next hw exception or syscall can't occur.
EIP is cleared by rted.
This change speedup page_fault hw exception handler
which is critical path.
There is also necessary to save R11 content before
flag setup for unaligned exception.
Michal Simek [Tue, 22 Jun 2010 12:05:43 +0000 (14:05 +0200)]
microblaze: Move BIP setup to the end of ret_from_trap/ret_from_exc
We don't need to protect by BIP whole ret_from_trap/ret_from_exc code.
Only restoring from user/hw exception should be covered.
If BIP is setup, IRQ can't occur.
Michal Simek [Tue, 22 Jun 2010 12:00:12 +0000 (14:00 +0200)]
microblaze: Remove PER_CPU(KM) variable
There is a way howto remove Kernel Mode variable. It is easier
to parse UMS bit in MSR to find out if I come from kernel or user
space. Loading MSR content should be in one cycle and loading
PER_CPU variable depends on memory state.
Michal Simek [Tue, 22 Jun 2010 11:27:43 +0000 (13:27 +0200)]
microblaze: Save and restore r3/r4 in SAVE/RESTORE_REGS macros
Save and restore R3/R4 registers in macros. This change
help to cleanup entry.S.
In ret_from_trap function we are saving returning value from
syscall to pt_regs on stack that's why we don't need to save and
restore these values before kernel functions (schedule, do_signal).
Implement intelligent backtracing by searching for stack frame creation,
and emitting only return addresses. Use print_hex_dump() to display the
entire binary kernel stack.
Limitation: MMU kernels are not currently able to trace beyond a system trap
(interrupt, syscall, etc.). It is the intent of this patch to provide
infrastructure that can be extended to add this capability later.
Changes from V1:
* Removed checks in find_frame_creation() that prevented location of the frame
creation instruction in heavily optimized code
* Various formatting/commenting/file location tweaks per review comments
* Dropped Kconfig option to enable STACKTRACE as something logically separate
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Michal Simek [Fri, 4 Jun 2010 11:06:27 +0000 (13:06 +0200)]
microblaze: Fix sys_clone syscall
sys_clone syscall ignored args which this patch mapped to args
which are passing from glibc.
Here is the origin problem description.
"I ran the static libgcc tests (very few of them are there, they are
mostly dynamically linked) and some of them fail with an assertion in
fork() system call (tid != pid), I looked at the microblaze/entry.S
file and it looks suspicious (ignores arguments 3-5)"
Michal Simek [Mon, 24 May 2010 10:13:24 +0000 (12:13 +0200)]
microblaze: Fix copy_to_user_page macro
copy_to_user_page macro is used in mm/memory.c:access_process_vm
function. This function is called from ptrace code (POKETEXT, POKEDATA)
which write data to memory. Microblaze handle physical address for
caches that's why there is virt_to_phys conversion.
There is potential one location which can caused the problem on WB system.
The important is take a look at write PTRACEs requests
(POKE/TEXT, DATA, USR).
Note:
Majority of Microblaze PTRACE code is moved to generic location
in newer kernel version that's why this solution should work on
the newest kernel version too.
Warning message:
arch/microblaze/mm/fault.c: In function 'do_page_fault':
arch/microblaze/mm/fault.c:229: warning: label 'survive' defined but not used
__copy_to/from_user_inatomic should call __copy_to/from_user
because there is not necessary to check access because of kernel function.
might_sleep in copy_to/from_user macros is causing problems
in debug sessions too (CONFIG_DEBUG_SPINLOCK_SLEEP).
BUG: sleeping function called from invalid context at
.../arch/microblaze/include/asm/uaccess.h:388
in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: swapper
1 lock held by swapper/1:
#0: (&p->cred_guard_mutex){......}, at: [<c00d4b90>] prepare_bprm_creds+0x2c/0x88
Kernel Stack:
...
* master.kernel.org:/home/rmk/linux-2.6-arm:
cyber2000fb: fix console in truecolor modes
cyber2000fb: fix machine hang on module load
SA1111: Eliminate use after free
ARM: Fix Versatile/Realview/VExpress MMC card detection sense
ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
ARM: Add barriers to io{read,write}{8,16,32} accessors as well
ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
ARM: 6271/1: Introduce *_relaxed() I/O accessors
ARM: 6275/1: ux500: don't use writeb() in uncompress.h
ARM: 6270/1: clean files in arch/arm/boot/compressed/
ARM: Fix csum_partial_copy_from_user()
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Ensure that writepage respects the nonblock flag
NFS: kswapd must not block in nfs_release_page
nfs: include space for the NUL in root path
Debian's ia64 autobuilders have been seeing kernel freeze or reboot
when running the gdb testsuite (Debian bug 588574): dannf bisected to
2.6.32 62eede62dafb4a6633eae7ffbeb34c60dba5e7b1 "mm: ZERO_PAGE without
PTE_SPECIAL"; and reproduced it with gdb's gcore on a simple target.
I'd missed updating the gate_vma handling in __get_user_pages(): that
happens to use vm_normal_page() (nowadays failing on the zero page),
yet reported success even when it failed to get a page - boom when
access_process_vm() tried to copy that to its intermediate buffer.
Fix this, resisting cleanups: in particular, leave it for now reporting
success when not asked to get any pages - very probably safe to change,
but let's not risk it without testing exposure.
Why did ia64 crash with 16kB pages, but succeed with 64kB pages?
Because setup_gate() pads each 64kB of its gate area with zero pages.
Reported-by: Andreas Barth <aba@not.so.argh.org> Bisected-by: dann frazier <dannf@debian.org> Signed-off-by: Hugh Dickins <hughd@google.com> Tested-by: dann frazier <dannf@dannf.org> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Fri, 30 Jul 2010 14:25:19 +0000 (15:25 +0100)]
CIFS: Remove __exit mark from cifs_exit_dns_resolver()
Remove the __exit mark from cifs_exit_dns_resolver() as it's called by the
module init routine in case of error, and so may have been discarded during
linkage.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ondrej Zary [Thu, 29 Jul 2010 20:40:54 +0000 (22:40 +0200)]
cyber2000fb: fix console in truecolor modes
Return value was not set to 0 in setcolreg() with truecolor modes. This causes
fb_set_cmap() to abort after first color, resulting in blank palette - and
blank console in 24bpp and 32bpp modes.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ondrej Zary [Thu, 29 Jul 2010 20:32:20 +0000 (22:32 +0200)]
cyber2000fb: fix machine hang on module load
I was testing two CyberPro 2000 based PCI cards on x86 and the machine always
hanged completely when the cyber2000fb module was loaded. It seems that the
card hangs when some registers are accessed too quickly after writing RAMDAC
control register. With this patch, both card work.
Add delay after RAMDAC control register write to prevent hangs on module load.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Julia Lawall [Fri, 30 Jul 2010 15:17:28 +0000 (17:17 +0200)]
SA1111: Eliminate use after free
__sa1111_remove always frees its argument, so the subsequent reference to
sachip->saved_state represents a use after free. __sa1111_remove does not
appear to use the saved_state field, so the patch simply frees it first.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
__sa1111_remove(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 29 Jul 2010 14:58:59 +0000 (15:58 +0100)]
ARM: Fix Versatile/Realview/VExpress MMC card detection sense
The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards. Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gary King [Thu, 29 Jul 2010 16:37:20 +0000 (17:37 +0100)]
ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
smp_processor_id() must not be called from a preemptible context (this
is checked by CONFIG_DEBUG_PREEMPT). kmap_high_l1_vipt() was doing so.
This lead to a problem where the wrong per_cpu kmap_high_l1_vipt_depth
could be incremented, causing a BUG_ON(*depth <= 0); in
kunmap_high_l1_vipt().
The solution is to move the call to smp_processor_id() after the call
to preempt_disable().
Originally by: Andrew Howe <ahowe@nvidia.com>
Signed-off-by: Gary King <gking@nvidia.com> Acked-by: Nicolas Pitre <nico.as.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
See https://bugzilla.kernel.org/show_bug.cgi?id=16056
If other processes are blocked waiting for kswapd to free up some memory so
that they can make progress, then we cannot allow kswapd to block on those
processes.
Dan Carpenter [Tue, 13 Jul 2010 11:34:59 +0000 (13:34 +0200)]
nfs: include space for the NUL in root path
In root_nfs_name() it does the following:
if (strlen(buf) + strlen(cp) > NFS_MAXPATHLEN) {
printk(KERN_ERR "Root-NFS: Pathname for remote directory too long.\n");
return -1;
}
sprintf(nfs_export_path, buf, cp);
In the original code if (strlen(buf) + strlen(cp) == NFS_MAXPATHLEN)
then the sprintf() would lead to an overflow. Generally the rest of the
code assumes that the path can have NFS_MAXPATHLEN (1024) characters and
a NUL terminator so the fix is to add space to the nfs_export_path[]
buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Merge branch 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add a PC-beep workaround for ASUS P5-V
ALSA: hda - Assume PC-beep as default for Realtek
ALSA: hda - Don't register beep input device when no beep is available
ALSA: hda - Fix pin-detection of Nvidia HDMI
David Howells [Thu, 29 Jul 2010 11:45:55 +0000 (12:45 +0100)]
CRED: Fix __task_cred()'s lockdep check and banner comment
Fix __task_cred()'s lockdep check by removing the following validation
condition:
lockdep_tasklist_lock_is_held()
as commit_creds() does not take the tasklist_lock, and nor do most of the
functions that call it, so this check is pointless and it can prevent
detection of the RCU lock not being held if the tasklist_lock is held.
Instead, add the following validation condition:
task->exit_state >= 0
to permit the access if the target task is dead and therefore unable to change
its own credentials.
Fix __task_cred()'s comment to:
(1) discard the bit that says that the caller must prevent the target task
from being deleted. That shouldn't need saying.
(2) Add a comment indicating the result of __task_cred() should not be passed
directly to get_cred(), but rather than get_task_cred() should be used
instead.
Also put a note into the documentation to enforce this point there too.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 29 Jul 2010 11:45:49 +0000 (12:45 +0100)]
CRED: Fix get_task_cred() and task_state() to not resurrect dead credentials
It's possible for get_task_cred() as it currently stands to 'corrupt' a set of
credentials by incrementing their usage count after their replacement by the
task being accessed.
What happens is that get_task_cred() can race with commit_creds():
However, since a tasks credentials are generally not changed very often, we can
reasonably make use of a loop involving reading the creds pointer and using
atomic_inc_not_zero() to attempt to increment it if it hasn't already hit zero.
If successful, we can safely return the credentials in the knowledge that, even
if the task we're accessing has released them, they haven't gone to the RCU
cleanup code.
We then change task_state() in procfs to use get_task_cred() rather than
calling get_cred() on the result of __task_cred(), as that suffers from the
same problem.
Without this change, a BUG_ON in __put_cred() or in put_cred_rcu() can be
tripped when it is noticed that the usage count is not zero as it ought to be,
for example:
ALSA: hda - Add a PC-beep workaround for ASUS P5-V
ASUS P5-V provides a SSID that unexpectedly matches with the value
compilant with Realtek's specification. Thus the driver interprets
it badly, resulting in non-working PC beep.
This patch adds a white-list for such a case; a white-list of known
devices with working PC beep.
Russell King [Thu, 29 Jul 2010 10:38:05 +0000 (11:38 +0100)]
ARM: Add barriers to io{read,write}{8,16,32} accessors as well
The ioread/iowrite accessors also need barriers as they're used in
place of readl/writel et.al. in portable drivers. Create __iormb()
and __iowmb() which are conditionally defined to be barriers dependent
on ARM_DMA_MEM_BUFFERABLE, and always use these macros in the accessors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
When the coherent DMA buffers are mapped as Normal Non-cacheable
(ARM_DMA_MEM_BUFFERABLE enabled), buffer accesses are no longer ordered
with Device memory accesses causing failures in device drivers that do
not use the mandatory memory barriers before starting a DMA transfer.
LKML discussions led to the conclusion that such barriers have to be
added to the I/O accessors:
This patch introduces a wmb() barrier to the write*() I/O accessors to
handle the situations where Normal Non-cacheable writes are still in the
processor (or L2 cache controller) write buffer before a DMA transfer
command is issued. For the read*() accessors, a rmb() is introduced
after the I/O to avoid speculative loads where the driver polls for a
DMA transfer ready bit.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
This patch is in preparation for a subsequent patch which adds barriers
to the I/O accessors. Since the mandatory barriers may do an L2 cache
sync, this patch avoids a recursive call into l2x0_cache_sync() via the
write*() accessors and wmb() and a call into l2x0_cache_sync() with the
l2x0_lock held.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces readl*_relaxed()/write*_relaxed() as the main I/O
accessors (when __mem_pci is defined). The standard read*()/write*()
macros are now based on the relaxed accessors.
This patch is in preparation for a subsequent patch which adds barriers
to the I/O accessors.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rabin Vincent [Thu, 29 Jul 2010 11:13:18 +0000 (12:13 +0100)]
ARM: 6275/1: ux500: don't use writeb() in uncompress.h
Don't use writeb() in uncompress.h, to avoid the following build errors
when the "Add barriers to the I/O accessors" series is applied. Use
__raw_writeb() instead.
arch/arm/boot/compressed/misc.o: In function `putc':
arch/arm/mach-ux500/include/mach/uncompress.h:41:
undefined reference to `outer_cache'
Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drm/radeon/kms: fix radeon mid power profile reporting
Fix incorrectly reporting 'default' power profile, when it is set to 'mid'.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com> Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
[SCSI] zfcp: Update status read mempool
[SCSI] zfcp: Do not wait for SBALs on stopped queue
[SCSI] zfcp: Fix check whether unchained ct_els is possible
[SCSI] ipr: fix resource path display and formatting
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
wm8350-regulator: fix wm8350_register_regulator error handling
ab3100: fix off-by-one value range checking for voltage selector
Andre Osterhues [Tue, 13 Jul 2010 20:59:17 +0000 (15:59 -0500)]
ecryptfs: Bugfix for error related to ecryptfs_hash_buckets
The function ecryptfs_uid_hash wrongly assumes that the
second parameter to hash_long() is the number of hash
buckets instead of the number of hash bits.
This patch fixes that and renames the variable
ecryptfs_hash_buckets to ecryptfs_hash_bits to make it
clearer.
Jason Wessel [Thu, 29 Jul 2010 00:10:30 +0000 (19:10 -0500)]
x86,kgdb: Fix hw breakpoint regression
HW breakpoints events stopped working correctly with kgdb
as a result of commit: 018cbffe6819f6f8db20a0a3acd9bab9bfd667e4
(Merge commit 'v2.6.33' into perf/core).
The regression occurred because the behavior changed for setting
NOTIFY_STOP as the return value to the die notifier if the breakpoint
was known to the HW breakpoint API. Because kgdb is using the HW
breakpoint API to register HW breakpoints slots, it must also now
implement the overflow_handler call back else kgdb does not get to see
the events from the die notifier.
The kgdb_ll_trap function will be changed to be general purpose code
which can allow an easy way to implement the hw_breakpoint API
overflow call back.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Acked-by: Dongdong Deng <dongdong.deng@windriver.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
If we don't need a huge amount of memory in ->readdir() then
we can use kmalloc rather than vmalloc to allocate it. This
should cut down on the greater overheads associated with
vmalloc for smaller directories.
We may be able to eliminate vmalloc entirely at some stage,
but this is easy to do right away.
Also using GFP_NOFS to avoid any issues wrt to deleting inodes
while under a glock, and suggestion from Linus to factor out
the alloc/dealloc.
I've given this a test with a variety of different sized
directories and it seems to work ok.
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Nick Piggin <npiggin@suse.de> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable PC-beep as default for hardwares that aren't compliant with the
SSID value Realtek requires. In such a case, better to enable the beep
to avoid a regression.
ALSA: hda - Don't register beep input device when no beep is available
We check now the availability of PC beep and skip the build of beep
mixers, but the driver still registers the input device. This should
be checked as well.
Sekhar Nori [Mon, 12 Jul 2010 12:26:21 +0000 (17:56 +0530)]
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
Per the da850/omap-l138 Beta EVM SOM schematic, the DEFDCDC2 and DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.
Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In TPS6507x, depending on the status of DEFDCDC{2,3} pin either DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.
The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).
Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.
The behavior of Nvidia HDMI codec regarding the pin-detection unsol events
is based on the old HD-audio spec, i.e. PD bit indicates only the update
and doesn't show the current state. Since the current code assumes the
new behavior, the pin-detection doesn't work relialby with these h/w.
This patch adds a flag for indicating the old spec, and fixes the issue
by checking the pin-detection explicitly for such hardware.
Tested-by: Wei Ni <wni@nvidia.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
The MPC85xx EDAC driver is missing module device aliases, so the driver
won't load automatically on boot. This patch fixes the issue by adding
proper MODULE_DEVICE_TABLE() macros.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Cc: Doug Thompson <dougthompson@xmission.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Dave Jiang <djiang@mvista.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rudolf Marek [Tue, 27 Jul 2010 20:18:02 +0000 (13:18 -0700)]
drivers/rtc/rtc-rx8581.c: fix setdatetime
Fix the logic while writing new date/time to the chip. The driver
incorrectly wrote back register values to different registers and even
with wrong mask. The patch adds clearing of the VLF register, which
should be cleared if all date/time values are set.
Signed-off-by: Rudolf Marek <rudolf.marek@sysgo.com> Acked-by: Wan ZongShun <mcuos.com@gmail.com> Cc: Martyn Welch <martyn.welch@gefanuc.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the call to ddebug_remove_module() down into free_module(). In this
way it should be called from all error paths. Currently, we are missing
the remove if the module init routine fails.
Signed-off-by: Jason Baron <jbaron@redhat.com> Reported-by: Thomas Renninger <trenn@suse.de> Tested-by: Thomas Renninger <trenn@suse.de> Cc: <stable@kernel.org> [2.6.32+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes an issue triggered by running concurrent syncs. One of the syncs
would go through while the other would just hang indefinitely. In any case, we
never actually want to wake a single waiter, so the *_all functions should
be used.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net> Signed-off-by: Sage Weil <sage@newdream.net>
The etr events switch-to-local and sync-check disable the synchronous clock
and schedule a work queue that tries to get the clock back into sync.
If another switch-to-local or sync-check event occurs while the work queue
function etr_work_fn still runs the eacr.es bit and the clock_sync_word can
become inconsistent because check_sync_clock only uses the clock_sync_word
to determine if the clock is in sync or not. The second pass of the
etr_work_fn will reset the eacr.es bit but will leave the clock_sync_word
intact. Fix this race by moving the reset of the eacr.es bit into the
switch-to-local and sync-check functions and by checking the eacr.es bit
as well to decide if the clock needs to be synced.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case user space is single stepped (PER) the program check handler
claims too early that IRQs are enabled on the return path.
Subsequent checks will notice that the IRQ mask in the PSW and
what lockdep thinks the IRQ mask should be do not correlate and
therefore will print a warning to the console and disable lockdep.
Fix this by doing all the work within the correct context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
srp_task needs to be setup before request_irq. The patch below fixes the oops.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
s2io: fixing DBG_PRINT() macro
ath9k: fix dma direction for map/unmap in ath_rx_tasklet
net: dev_forward_skb should call nf_reset
net sched: fix race in mirred device removal
tun: avoid BUG, dump packet on GSO errors
bonding: set device in RLB ARP packet handler
wimax/i2400m: Add PID & VID for Intel WiMAX 6250
ipv6: Don't add routes to ipv6 disabled interfaces.
net: Fix skb_copy_expand() handling of ->csum_start
net: Fix corruption of skb csum field in pskb_expand_head() of net/core/skbuff.c
macvtap: Limit packet queue length
ixgbe/igb: catch invalid VF settings
bnx2x: Advance a module version
bnx2x: Protect statistics ramrod and sequence number
bnx2x: Protect a SM state change
wireless: use netif_rx_ni in ieee80211_send_layer2_update
Peter Zijlstra [Fri, 9 Jul 2010 08:21:21 +0000 (10:21 +0200)]
perf, powerpc: Use perf_sample_data_init() for the FSL code
We should use perf_sample_data_init() to initialize struct
perf_sample_data. As explained in the description of commit dc1d628a
("perf: Provide generic perf_sample_data initialization"), it is
possible for userspace to get the kernel to dereference data.raw,
so if it is not initialized, that means that unprivileged userspace
can possibly oops the kernel. Using perf_sample_data_init makes sure
it gets initialized to NULL.
This conversion should have been included in commit dc1d628a, but it
got missed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Kumar Gala <kumar.gala@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
In the case of platform_device_add() fail, we should call
platform_device_put() instead of platform_device_del()
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Axel Lin [Mon, 26 Jul 2010 07:34:14 +0000 (15:34 +0800)]
ab3100: fix off-by-one value range checking for voltage selector
We use voltage selector as an array index for typ_voltages.
Thus the valid range for voltage selector should be 0..voltages_len-1.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Do not try to disable hpet if it hasn't been initialized before
x86, i8259: Only register sysdev if we have a real 8259 PIC
Patch 9e39f7c5b311a306977c5471f9e2ce4c456aa038 changed the
DBG_PRINT() macro and the if clause was wrongly changed. It means
that currently all the DBG_PRINT are being printed, flooding the
kernel log buffer with things like:
s2io: eth6: Next block at: c0000000b9c90000
s2io: eth6: In Neterion Tx routine
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Set io_map_base for several PCI bridges lacking it
MIPS: Alchemy: Define eth platform devices in the correct order
MIPS: BCM63xx: Prevent second enet registration on BCM6338
MIPS: Quit using undefined behavior of ADDU in 64-bit atomic operations.
MIPS: N32: Define getdents64.
MIPS: MTX-1: Fix PCI on the MeshCube and related boards
MIPS: Make init_vdso a subsys_initcall.
MIPS: "Fix" useless 'init_vdso successfully' message.
MIPS: PowerTV: Move register setup to before reading registers.
SOUND: Au1000: Fix section mismatch
VIDEO: Au1100fb: Fix section mismatch
VIDEO: PMAGB-B: Fix section mismatch
VIDEO: PMAG-BA: Fix section mismatch
NET: declance: Fix section mismatches
VIDEO. gbefb: Fix section mismatches.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
sysfs: allow creating symlinks from untagged to tagged directories
sysfs: sysfs_delete_link handle symlinks from untagged to tagged directories.
sysfs: Don't allow the creation of symlinks we can't remove
projects / linux-beck.git / log