Jani Nikula [Fri, 8 Nov 2013 14:48:57 +0000 (16:48 +0200)]
drm/i915: fix gen2-gen3 backlight set
Citing Jani's response to Imre's question in the review discussion:
> According to the gen2/3 bspec I have, the correct mask is
> BACKLIGHT_DUTY_CYCLE_MASK_PNV only in case of IS_PINEVIEW(dev), for
> everything else it's BACKLIGHT_DUTY_CYCLE_MASK.
What you say is correct, but we've treated all gen2/3 similar to PNV
since
drm/i915: Treat pre-gen4 backlight duty cycle value consistently
i.e. we only use the high 15 bits for all gen2/3. For non-PNV this just
means the lowest bit is always zero. For PNV the lowest bit has a
different meaning in both the PWM freq and duty cycle fields.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Make the commit message less empty.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 8 Nov 2013 14:48:56 +0000 (16:48 +0200)]
drm/i915: handle backlight through chip specific functions
The backlight code has grown rather hairy, not least because the
hardware registers and bits have repeatedly been shuffled around. And
this isn't expected to get any easier with new hardware. Make things
easier for our (read: my) poor brains, and split the code up into chip
specific functions.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 8 Nov 2013 14:48:55 +0000 (16:48 +0200)]
drm/i915: make asle notifications update backlight on all connectors
ALthough usually there's only one connector that supports backlight,
this also finds the correct connector. Before, we only updated the
connector on pipe A, which might not be the one with backlight. (This
only made a difference on BYT.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 8 Nov 2013 14:48:54 +0000 (16:48 +0200)]
drm/i915: make backlight info per-connector
Move from dev_priv to connector->panel. We still don't allow multiple
sysfs interfaces, though.
There should be no functional changes, except for a slight reordering of
connector backlight and sysfs destroy calls. (This change happens now
that the backlight device is actually per-connector, even though the
destroy calls became per-connector earlier.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Sun, 10 Nov 2013 21:25:33 +0000 (07:25 +1000)]
Merge branch 'gma500-next' of git://github.com/patjak/drm-gma500 into drm-next
SDVO support for minnowboard
* 'gma500-next' of git://github.com/patjak/drm-gma500:
drm/gma500/mrst: Add SDVO to output init
drm/gma500/mrst: Don't blindly guess a mode for LVDS
drm/gma500/mrst: Setup GMBUS for oaktrail/mrst
drm/gma500/mrst: Replace WMs and chickenbits with values from EMGD
drm/gma500/mrst: Add aux register writes to SDVO
drm/gma500/mrst: Properly route oaktrail hdmi hooks
drm/gma500/mrst: Add aux register writes when programming pipe
drm/gma500/mrst: Add SDVO clock calculation
drm/gma500: Add aux device support for gmbus
drm/gma500: Add support for aux pci vdc device
drm/gma500: Add chip specific sdvo masks
drm/gma500: Add Minnowboard to the IS_MRST() macro
Laurent Pinchart [Mon, 28 Oct 2013 22:49:22 +0000 (23:49 +0100)]
drm: shmob_drm: Convert to clk_prepare/unprepare
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Cc: David Airlie <airlied@linux.ie> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sun, 10 Nov 2013 08:35:33 +0000 (18:35 +1000)]
Merge tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
So here's the Broadwell pull request. From a kernel driver pov there's
two areas with big changes in Broadwell:
- Completely new enumerated interrupt bits. On the plus side it now looks
fairly unform and sane.
- Completely new pagetable layout.
To ensure minimal impact on existing platforms we've refactored both the
irq and low-level gtt handling code a lot in anticipation of the bdw push.
So now bdw enabling in these areas just plugs in a bunch of vfuncs.
Otherwise it's all fairly harmless adjusting of switch cases and
if-ladders to shovel bdw into the right blocks. So minimized impact on
existing platforms. I've also merged the bdw-stage1 branch into our
-nightly integration branch for the past week to make sure we don't break
anything.
Note that there's still quite a flurry or patches floating around, but
I've figured I'll push this out. I plan to keep the bdw fixes separate
from my usual -fixes stream so that you can reject them easily in case it
still looks like too much churn. Also, bdw is for now hidden behind the
preliminary hw enabling module option. So there's no real pressure to get
follow-up patches all into 3.13.
* tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel: (75 commits)
drm/i915: Mask the vblank interrupt on bdw by default
drm/i915: Wire up cpu fifo underrun reporting support for bdw
drm/i915: Optimize gen8_enable|disable_vblank functions
drm/i915: Wire up pipe CRC support for bdw
drm/i915: Wire up PCH interrupts for bdw
drm/i915: Wire up port A aux channel
drm/i915: Fix up the bdw pipe interrupt enable lists
drm/i915: Optimize pipe irq handling on bdw
drm/i915/bdw: Take render error interrupt out of the mask
drm/i915/bdw: Add BDW PCH check first
drm/i915: Use hsw_crt_get_config on BDW
drm/i915/bdw: Change dp aux timeout to 600us on DDIA
drm/i915/bdw: Enable trickle feed on Broadwell
drm/i915/bdw: WaSingleSubspanDispatchOnAALinesAndPoints
drm/i915/bdw: conservative SBE VUE cache mode
drm/i915/bdw: Limit SDE poly depth FIFO to 2
drm/i915/bdw: Sampler power bypass disable
ddrm/i915/bdw: Disable centroid pixel perf optimization
drm/i915/bdw: BWGTLB clock gate disable
drm/i915/bdw: Implement edp PSR workarounds
...
Dave Airlie [Sun, 10 Nov 2013 08:33:17 +0000 (18:33 +1000)]
Merge branch 'drm-next-3.13' of git://people.freedesktop.org/~agd5f/linux into drm-next
A few more patches for 3.13. The big one here is Hawaii support.
I wanted to get that out sooner, but was sick earlier this week. That
said, it's mostly self contained, so it shouldn't impact other asics.
The rest are just bug fixes and a merge fix.
* 'drm-next-3.13' of git://people.freedesktop.org/~agd5f/linux: (23 commits)
Revert "drm/radeon/audio: don't set speaker allocation on DCE4+"
drm/radeon/audio: improve ACR calculation
drm/radeon/audio: correct ACR table
drm/radeon: fix mismerge of drm-next with 3.12
drm/radeon: add pci ids for hawaii
drm/radeon: fill in radeon_asic_init for hawaii
drm/radeon: modesetting updates for hawaii
drm/radeon: atombios.h updates for hawaii
drm/radeon: update cik_get_csb_buffer for hawaii
drm/radeon: add hawaii dpm support
drm/radeon/cik: add hawaii UVD support
drm/radeon: update firmware loading for hawaii
drm/radeon: update rb setup for hawaii
drm/radeon: add golden register settings for hawaii
drm/radeon: update cik_tiling_mode_table_init() for hawaii
drm/radeon: minor updates to cik.c for hawaii
drm/radeon: update cik_gpu_init() for hawaii
drm/radeon: add Hawaii chip family
drm/radeon: fix-up some float to fixed conversion thinkos
drm/radeon: use HDP_MEM_COHERENCY_FLUSH_CNTL for sdma as well
...
Dave Airlie [Sun, 10 Nov 2013 08:27:31 +0000 (18:27 +1000)]
Merge branch 'msm-next' of git://people.freedesktop.org/~robclark/linux into drm-next
prime support, inactive rework, render nodes
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/msm/mdp4: page_flip cleanups/fixes
drm/msm: EBUSY status handling in msm_gem_fault()
drm/msm: rework inactive-work
drm/msm: add plane support
drm/msm: resync generated headers
drm/msm: support render nodes
drm/msm: prime support
Let's try this again for 3.13. It's required for proper
interaction with alsa. Was disabled previously in 3.12
to be on the safe side since it caused problems on older
asics.
Pierre Ossman [Wed, 6 Nov 2013 19:09:08 +0000 (20:09 +0100)]
drm/radeon/audio: improve ACR calculation
In order to have any realistic chance of calculating proper
ACR values, we need to be able to calculate both N and CTS,
not just CTS. We still aim for the ideal N as specified in
the HDMI spec though.
Pierre Ossman [Wed, 6 Nov 2013 19:00:32 +0000 (20:00 +0100)]
drm/radeon/audio: correct ACR table
The values were taken from the HDMI spec, but they assumed
exact x/1.001 clocks. Since we round the clocks, we also need
to calculate different N and CTS values.
Note that the N for 25.2/1.001 MHz at 44.1 kHz audio is out of
spec. Hopefully this mode is rarely used and/or HDMI sinks
tolerate overly large values of N.
Ilija Hadzic [Sun, 3 Nov 2013 03:00:20 +0000 (23:00 -0400)]
drm/radeon/kms: add crtc_disable function for legacy crtc
To plug the VRAM memory leak (see previous patch for
details) we must unpin the frame buffer when disabling the
CRTC. This warrants the addition of disable function for legacy
CRTC, which puts the CRTC in DPMS-OFF state and unpins the
frame buffer if there is one associated with the CRTC.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ilija Hadzic [Sun, 3 Nov 2013 03:00:19 +0000 (23:00 -0400)]
drm/radeon/kms: unpin fb in atombios crtc disable
When drm_helper_disable_unused_functions calls disable
function of the CRTC, it also sets the crtc->fb pointer
to NULL. This can later (when the mode on that CRTC is setup
again from user space) cause ***_do_set_base functions to
"think" that there is no old buffer and skip the unpinning
code. Consequently, the buffer that has been NULL-ified in
drm_helper_disable_unused_functions will never be unpinned
causing a leak in VRAM.
This patch plugs the leak by unpinning the frame buffer
in crtc_disable function.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Anssi Hannula [Mon, 28 Oct 2013 23:19:16 +0000 (01:19 +0200)]
drm/radeon/audio: fix missing multichannel PCM SAD in some cases
The current code writing SADs to the audio registers seems to assume
that there is at most a single SAD per audio format.
However, that is not the case. Especially for PCM it is somewhat common
for sinks to have two SADs, one for 8-channel and one for 2-channel
audio, which may have different supported sample rates (i.e. the sink
supports stereo audio at higher sample rates than multichannel audio).
Because of this, only the 2-channel SAD may be used if it appears before
the 8-channel SAD. Unless other SADs require otherwise, this may cause
the ALSA HDA driver to allow stereo playback only.
Fix the code to pick the PCM SAD with the highest number of channels,
while merging the rate masks of PCM SADs with lower amount of channels
into the additional stereo rate mask byte.
Technically there are even more cases to handle (multiple non-PCM SADs
of the same type, more than two PCM SADs with varying channel counts,
etc), but those have not actually been encountered in the field and
handling them would be non-trivial.
Daniel Vetter [Thu, 7 Nov 2013 14:31:52 +0000 (15:31 +0100)]
drm/i915: Mask the vblank interrupt on bdw by default
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 7 Nov 2013 10:05:46 +0000 (11:05 +0100)]
drm/i915: Wire up cpu fifo underrun reporting support for bdw
HW engineers have listened and given us again a real interrupt with
masking and status regs. Yay!
For consistency with other platforms call the #define FIFO_UNDERRUN.
Eventually we also might need to have some enable/disable functions
for bdw display interrupts, but for now open-coding seems to be good
enough.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's cache the IMR value like on other platforms. This is needed to
implement the underrun reporting since then we'll have two places that
change the same register at runtime.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 7 Nov 2013 10:05:43 +0000 (11:05 +0100)]
drm/i915: Wire up PCH interrupts for bdw
Gives us hotplug, gmbus, dp aux and south errors (underrun
reporting!).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 7 Nov 2013 13:49:55 +0000 (14:49 +0100)]
drm/i915: Wire up port A aux channel
Useful for dp aux to work better. Also stop enabling the port A
hotplug event - eDP panels are expected to fire that interupt and
we're not really ready to deal with them. This is consistent with how
we handle port A on ilk-hsw.
The more important bit is that we must delay the enabling of hotplug
interrupts until all the encoders are fully set up. But we need irq
support earlier than that, hence hotplug interrupts can only be
enabled in the ->hpd_irq_setup callback.
v2: Drop the _HOTPLUG, it isn't (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 7 Nov 2013 13:49:24 +0000 (14:49 +0100)]
drm/i915: Fix up the bdw pipe interrupt enable lists
- Pipe underrun can't just be enabled, we need some support code like
on ilk-hsw to make this happen. So drop it for now.
- CRC error is a special mode of the CRC hardware that we don't use,
so again drop it. Real CRC support for bdw will be added later.
- All the other error bits are about faults, so rename the #define and
adjust the output.
v2: Use pipe_name as pointed out by Ville. Ville's comment was on a
previous patch, but it was easier to squash in here.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 7 Nov 2013 10:05:40 +0000 (11:05 +0100)]
drm/i915: Optimize pipe irq handling on bdw
We have a per-pipe bit in the master irq control register, so use it.
This allows us to drop the masks for aggregate interrupt bits and be a
bit more explicit in the code. It also removes one indentation level.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v3: Update with workaround names.
Use for_each_pipe() and CHICKEN_PIPESL_1(pipe) macro (Ville)
Cc: Art Runyan <arthur.j.runyan@intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
[danvet: Kill redundant IS_BDW check and remove the copious amount of
uneeded lines added.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:52 +0000 (21:07 -0700)]
drm/i915/bdw: Create a separate BDW rps enable
This is mostly what we have for HSW with the exceptions of:
no writes:
GEN6_RC1_WAKE_RATE_LIMIT
GEN6_RC6pp_WAKE_RATE_LIMIT
GEN6_RC1e_THRESHOLD
GEN6_RC6p_THRESHOLD
GEN6_RC6pp_THRESHOLD
GEN6_RP_DOWN_TIMEOUT - use 1s instead of 1.28s
Don't try to overclock, or program ring/IA frequency tables since we
don't quite have sufficient docs yet.
NOTE: These values do not reflect the changes made recently by Chris.
Since we have no evidence yet what the proper way to tweak for this
platform is, I think it is good to go, and can be optimized by Chris, or
whomever, later.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Drop spurious hunk and drop TODO - having per-platform rps
register frobbing code is in my opinion preferred, now that all the
infrastructure functions are extracted.] Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:50 +0000 (21:07 -0700)]
drm/i915/bdw: Don't wait for c0 threads on forcewake
It's no longer a required workaround on BDW.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Move compile fix from a later patch to this one.] Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:49 +0000 (21:07 -0700)]
drm/i915/bdw: Use HSW formula for ring freq scaling
The current formula we use for HSW is not what is in current docs.
However, changing to the HSW formula on my HSW does not improve power
usage, and decreases performance by about 5% in limited xonotic testing.
For gen8, until we know otherwise, or run experiments, let's use
the HSW formula - which should be the same used in the Windows driver
(and thus help make an apples-applies comparison) on gen8.
v2: Use >= 8 instead of > 7 to be consistent with all other gen
checks.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 5 Nov 2013 06:45:05 +0000 (22:45 -0800)]
drm/i915/bdw: Support eDP PSR
Broadwell PSR support is a superset of Haswell. With this simple
register base calculation, everything that worked on HSW for eDP PSR
should work on BDW.
Note that Broadwell provides additional PSR support. This is not
addressed at this time.
v2: Make the HAS_PSR include BDW
v3: Use the correct offset (I had incorrectly used one from my faulty
brain) (Art!)
v4: It helps if you git add
v5: Be explicit about not setting min link entry time for BDW. This
should be no functional change over v4 (Jani)
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:47 +0000 (21:07 -0700)]
drm/i915/bdw: Use The GT mailbox for IPS enable/disable
v2: Squash in fixup from Ben to synchronize the GT mailbox commands.
CC: Art Runyan <arthur.j.runyan@intel.com> Reviewed-by: Art Runyan <arthur.j.runyan@intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Sun, 3 Nov 2013 04:07:46 +0000 (21:07 -0700)]
drm/i915/bdw: Add Broadwell display FIFO limits
Broadwell has bigger display FIFOs than Haswell. Otherwise the
two are very similar.
v2: Fix FBC WM_LP shift for BDW
v3: Rebase on top of the big Haswell wm rework.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2) Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:45 +0000 (21:07 -0700)]
drm/i915/bdw: check DPD on port D when setting the DDI buffers
Use the eDP values on platforms where port D is eDP. This doesn't
affect Haswell since it uses the same DDI buffer values for eDP and
DP.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:44 +0000 (21:07 -0700)]
drm/i915/bdw: BDW also has only 2 FDI lanes
So treat it like Haswell.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:42 +0000 (21:07 -0700)]
drm/i915/bdw: add BDW DDI buf translations for eDP
Broadwell has different DDI buffer translations for eDP and DP, so add
support for the missing eDP and keep Haswell the same.
A future patch addresses the suggestion from Art to check for eDP on
port D and use the eDP values there, too.
v2: Make checkpatch happy.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1) Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many of the DDI buffer translation values have changed for BDW.
Add new translation tables and selection between HSW and BDW.
v2: s/BUG/WARN/ to avoid breaking future GENs.
v3: Rebase on top of the hdmi translation table changes.
v4: Fix up the multiline comment while at it.
Signed-off-by: Art Runyan <arthur.j.runyan@intel.com> (v2) Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a generic comment that we need to recheck all these w/a.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Sun, 3 Nov 2013 04:07:39 +0000 (21:07 -0700)]
drm/i915/bdw: Use pipe CSC on Broadwell
Route cursor and sprite data through the pipe CSC unit on BDW.
Primary plane data is already sent through the pipe CSC.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:36 +0000 (21:07 -0700)]
drm/i915/bdw: get the correct LCPLL frequency on Broadwell
v2: Rebased onto Paulo's MHz->kHz change.
v3: Rebased on top of the Haswell pc8+ adjustements.
v4: Use the exact 337.5MHz clock, should have been done as part of v2.
Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:38 +0000 (21:07 -0700)]
drm/i915/bdw: Broadwell has PIPEMISC
And it inherits some bits from the previous TRANS_CONF (aka PIPE_CONF
on previous gens).
v2: Rebase on to of the pipe config bpp handling rework.
v3: Rebased on top of the pipe_config->dither refactoring.
v4: Drop the read-modify-write cycle for PIPEMISC, similarly to how we
now also build up PIPECONF completely ourselves - keeping around
random stuff set by the BIOS just isn't a good idea. I've checked BDW
BSpec and we already set all relevant bits.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:37 +0000 (21:07 -0700)]
drm/i915/bdw: on Broadwell, the panel fitter is on the pipe
So you can use the panel fitter while the power well is disabled and
you also don't need to set the "pipe" bit.
v2: Rebased on top of Jesse's pfit refactor, which moved pfit state
into the pipe_config.
v3: Rebase on top of the latest Haswell/panel fitter rework, which
neatly resolves a FIXME we have in this patch here:
v4: Rebase on top of the new power domain framework.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:35 +0000 (21:07 -0700)]
drm/i915/bdw: pretend we have LPT LP on Broadwell
The platforms we currently have all have LPT LP on them. As such, we
have no way to identify the new WPT PCH that will ship with Broadwell.
NOTE: For all purposes relevant to the driver that this point, LPT and
WPT are equivalent. Therefore there should be no need to actually change
this for some time.
v2: Don't assign dev_priv->num_pch_pll any more.
v3: Rebase on top of the PCH detection changes for virtualized
enviroments.
v4: Wrote commit message
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v3) Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:34 +0000 (21:07 -0700)]
drm/i915/bdw: Broadwell also has the "power down well"
Just like Haswell, but with the small twist that the panel fitter for pipe A is
now also in the always-on power well.
v2: Use the new HAS_POWER_WELL macro.
v3: Rebase on top of intel_using_power_well patches.
v4: This time actually update the PFIT check correctly so that the
pipe A pfit is in the always-on domain.
v5: Rebase on top of the VGA power domain addition.
v6: Rebase on top of the new power domain infrastructure. Also pimp the commit
message a bit while at it.
v7: Use IS_BROADWELL instead of IS_GEN8 (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just make Broadwell follow the same code paths as Haswell here,
instead of running code for the even-older platforms.
v2: Shuffle around Ben's vma prep work.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Sun, 3 Nov 2013 04:07:31 +0000 (21:07 -0700)]
drm/i915/bdw: add IS_BROADWELL macro
For now it's just equivalent to IS_GEN8, but in the future we might
want to change that (e.g., on Gen 7 we have IS_VALLEYVIEW,
IS_IVYBRIDGE and IS_HASWELL).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Sun, 3 Nov 2013 04:07:29 +0000 (21:07 -0700)]
drm/i915/bdw: Don't muck with gtt_size on Gen8 when PPGTT setup fails
v2: Resolve rebase conflicts and switch to gen < 8 color for GenX
checking.
v3: Rebase on top of the address space refactoring.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:27 +0000 (21:07 -0700)]
drm/i915/bdw: Render ring flushing
PIPE_CONTROL added the high address dword. I'm not sure how the
simulator let me get away with this. I've explicitly left out all the
workarounds from Gen7 because in the minimal digging that I did, most
don't seem necessary, and the simulator doesn't complain without them
Note that BLT and BSD ring commands had already been updated previously.
Just render/pipe_control should have been broken.
v2: Squash in a fixup from Ville to follow the recent IVB PIPE_CONTROL
updates: "BDW uses the IVB PIPE_CONTROL style for specifying GTT vs.
PPGTT for the PIPE_CONTROL QW/DW write."
v3: Rebase on top of Chris' cleanup to have an explicit ring->scratch
buffer object instead of an opaque ring->private where everyone stores
the same stuff inside.
Reported-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (for the fixup) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:26 +0000 (21:07 -0700)]
drm/i915/bdw: unleash PPGTT
v2: Squash in fix from Ben: Set PPGTT batches as necessary
This fixes the regression in the last couple of days when we enabled
PPGTT.
v3: Squash in fixup to still use GTT for secure batches from Ville:
BDW doesn't have a separate secure vs. non-secure bit in
MI_BATCH_BUFFER_START. So for secure batches we have to simply
leave the PPGTT bit unset. Fortunately older generations (except
HSW) had similar limitations so execbuffer already creates a GTT
mapping for all secure batches.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 5 Nov 2013 06:29:36 +0000 (22:29 -0800)]
drm/i915/bdw: Implement PPGTT enable
Legacy PPGTT on GEN8 requires programming 4 PDP registers per ring.
Since all rings are using the same address space with the current code
the logic is simply to program all the tables we've setup for the PPGTT.
v2: Turn on PPGTT in GFX_MODE
v3: v2 was the wrong patch
v4: Resolve conflicts due to patch series reordering.
v5: Squash in fixup from Ben: Use LRI to write PDPs
The docs (and simulator seems to back up) suggest that we can only
program legacy PPGTT PDPs with LRI commands.
v6: Rebase around context differences conflicts.
v7: Use #defines for per ring PDPs. (Damien)
v8: Don't use typede'f private_t.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (up to v3 and v7) Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 5 Nov 2013 05:20:14 +0000 (21:20 -0800)]
drm/i915/bdw: Initialize the PDEs
The upcoming clear and insert routines will expect that PDEs all point
to valid Page Directories. Doing that lazily doesn't really buy us
anything.
The page allocation is done regardless earlier in init so it shouldn't
hurt set the PDEs.
v2: Squash in patches to implement fixed PDE write function:
- If I had done this in the first place, the bug that's going to be
fixed in an upcoming patch would have been much easier to find.
- Use WB for PDEs.
The PAT bit is used for page size. 2ME PDEs aren't even supported in
BDW, so this was completely invalid. The solution is to make our
PDEs WB+LLC instead of the pervious WB+eLLC. As far as I can guess,
this change won't matter for performance.
Thanks to Ville for the quick correction when discussing on IRC.
v3: Return the pde type for pde encoding (Damien)
Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 5 Nov 2013 04:47:32 +0000 (20:47 -0800)]
drm/i915/bdw: PPGTT init & cleanup
Aside from the potential size increase of the PPGTT, the primary
difference from previous hardware is the Page Directories are no longer
carved out of the Global GTT.
Note that the PDE allocation is done as a 8MB contiguous allocation,
this needs to be eventually fixed (since driver reloading will be a
pain otherwise). Also, this will be a no-go for real PPGTT support.
v2: Move vtable initialization
v3: Resolve conflicts due to patch series reordering.
v4: Rebase on top of the address space refactoring of the PPGTT
support. Drop Imre's r-b tag for v2, too outdated by now.
v5: Free the correct amount of memory, "get_order takes size not a page
count." (Imre)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 5 Nov 2013 03:56:49 +0000 (19:56 -0800)]
drm/i915/bdw: Support BDW caching
BDW caching works differently than the previous generations. Instead of
having bits in the PTE which directly control how the page is cached,
the 3 PTE bits PWT PCD and PAT provide an index into a PAT defined by
register 0x40e0. This style of caching is functionally equivalent to how
it works on HSW and before.
v2: Tiny bikeshed as discussed on internal irc.
v3: Squash in patch from Ville to mirror the x86 PAT setup more like
in arch/x86/mm/pat.c. Primarily, the 0th index will be WB, and not
uncached.
v4: Comment for reason to not use a 64b write on the PPAT.
v5: Add a FIXME comment that the caching bits in the PAT registers
might be wrong due to doc confusion.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1) Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 5 Nov 2013 03:32:22 +0000 (19:32 -0800)]
drm/i915/bdw: Make gen8_gmch_probe
Probing gen8 is similar to gen6. To make the code cleaner and more
maintainable however we can use the probe functions to split it out.
v2: Rebased on top of update gtt probe infrastructure.
v3: Rebased on top of Kenneth' Graunke's ->pte_encode refactoring.
V4: Resolve conflicts with Ben's latest ppgtt patches, also switch to
gen < 8 testing instead of gen <= 7.
v5: Resolve conflicts with address space vfunc changes in upstream.
v6: Use 39b DMA mask. At least, for this mode, it is the correct mask.
(Imre)
Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:15 +0000 (21:07 -0700)]
drm/i915/bdw: Update relevant error state
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:14 +0000 (21:07 -0700)]
drm/i915/bdw: debugfs updates
All the gen8 debugfs stuff I wasn't too lazy to update. We'll need more
later, I am certain.
v2: Fix up the register name in the debugfs output as suggested by
Paulo.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1) Reviewed-by: Paulo Zanoni <przanoni@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sun, 3 Nov 2013 04:07:13 +0000 (21:07 -0700)]
drm/i915/bdw: Update MI_FLUSH_DW
The code is more verbose than necessary for the reader's sake, hopefully
the compiler optimizes away the if.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / linux-beck.git / log