Pekka Enberg [Wed, 14 Jul 2010 10:12:57 +0000 (13:12 +0300)]
[SCSI] aic7xxx: Remove OS utility wrappers
This patch removes malloc(), free(), and printf() wrappers from the aic7xxx
SCSI driver. I didn't use pr_debug for printf because of some 'clever' uses of
printf don't compile with the pr_debug. I didn't fix the overeager uses of
GFP_ATOMIC either because I wanted to keep this patch as simple as possible.
[jejb:fixed up checkpatch errors and fixed up missed conversion] Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Acked-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[SCSI] qla4xxx: unblock iscsi session after setting ddb state online.
Once the device goes *missing*, driver blocks the session
ie iscsi_block_session() to stall the I/O. So after device
comes back *online*, driver needs to unblock the session ie
iscsi_unblock_session(), else I/Os will fail even if
ddb_state is ONLINE.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: Ravi Anand <ravi.anand@qlogic.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add debugfs support to obtain firmware trace, driver trace
and read/write to registers.
- debugfs hierarchy:
/sys/kernel/debug/bfa/host#
where the host number corresponds to the one under /sys/class/scsi_host/host#
- Following are the new debugfs entries added:
drvtrc: collect current driver trace
fwtrc: collect current firmware trace.
fwsave: collect last saved fw trace as a result of firmware crash.
regwr: write one word to chip register
regrd: read one or more words from chip register.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes 3 bugs in vport create/delete.
1) Replace scsi_add_host() with scsi_add_host_with_dma()
2) Fix rmmod hang when there are vports configured. This is due to a race
condition between the workqueue destroy in pci remove context and the vport
delete works being handled. The fix is to use a counter to track the
vport delete work, so that workqueue destroy will not be called until all
configured vports are deleted from workqueue.
3) Fix rmmmod crash when there are PBC vport configured. PBC is not allowed
to be deleted dynamically. However, if someone try to delete it, it leaves the
vport is wrong state. The fix is to restore the vport back to original state
when the attempt to delete pbc vport delete is failed.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
While processing the ioim in callback functions, the ioim is still in io_q.
During this time, if the itnim goes offline, the ioim is requeued from
itnim->io_q into itnim->delay_comp_q although the request is already completed.
This results in requeing the ioim into the callback queue if the ioim is not
freed by the time the ioim is requeued. This results in double completion of
the ioim. To fix this, whenever a response is received from firmware for an
ioim, deque it from io_q and enque to fcpim->comp_q. This will eliminate any
possibility of itnim picking any ioim for which the response is already
received.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the FCoE Linkup event is sent to the host, the link_state
(struct bfa_pport_link_s) structure is copied to the RME buf to be sent to
the host. But the size of this structure(164 bytes) is larger than the
reserved RME buffer size(128 byes). The following changes reduce the size
of the structure to be less than RME buffer size(128 bytes):
- Remove the trunk and loop info from link_state structure, because both trunk
and loop are not supported.
- Combine qos_vc_attr and fcf into an union.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[SCSI] bfa: fix uf post and rport fcpim state machine
BFA UF module did not hold lock when seding uf post buffer message to firmware
causing CPE-Q corruption. Fix is to check present of FCS and if FCS present
hold lock while posting UF buffers.
Handle PRLO with sending acc to it and relogin with rport. Discard fcxp
before any state change.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear PSS memory reset that is set as part of power-on-reset (pci reset).
Complete PMM memory reset before BISTR start. Clear EDRAM BISTR start bit
after fixed delay. BISTR DONE bit status is not getting set. Use a fixed
1ms delay for BISTR now. Expose PMM IT memory definitions to host.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add a max retry limit for PRLI retries. Max retry limit (5) is same as used
in rport PLOGI. Once the retries are exhausted, invoke rport offline so that
existing logic of rport re-discovery can kick-in. Also fixed a bug in rport.c
where one less retry was happening.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a rport goes offline, its speed setting was not reset. Subsequently, if
the rport was not deleted due to it coming back online within rport del
timeout, previously discovered speed would continue to show up. The fix is to
reset the speed when processing rport offline transition.
In rport attributes, rport's with unknown speed were indicated as TRL
enforced. The right thing do to would be to use TRL default speed to
determine if TRL is enforced, when TRL is enabled.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Do not update the coalesce flag of the intr_attr struct in driver config area
on config response. This is to prevent the coalesce flag being reported as on
after an ioc disable/enable even if it was set to off before disable.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[SCSI] bfa: use standards defined timeout for ELS/CT
Use standards defined 2 * RA_TOV as a timeout for ELS Request retries.
And standards defined 3 * RA_TOV as a timeout for FC-CT Request retries.
Also, added a check to send RPSC2 to a Brocade Fabric only.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes the APIs to obtain ioc attributes
- fix API to obtain wwpn, wwnn, and mac.
- add API to get mfg wwpn, wwnn, and mac.
- fix API to obtain wwn of boot target.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Vport state machine does not cleanup associated lport in some states: while
waiting for fdisc response or fdisc failure state. The fixe is to cleanup lport
on vport delete in all states. In fdisc state, discard fdisc response and
delete lport and wait for lport deletecompletion. in error state, delete lport
and wait for delete completion.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch enables creating PBC vport.
During fcs init, fcs will read PBC vport using bfa iocfc API and invoke fcb
callback to add the pbc vport entries into a list. The pbc vport list will be
traversed in the subsequent pci probe process and vport will be created using
fc transport provided vport create function.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The patch includes the driver side changes to enable basic PBC (PreBoot
Configuration) feature.
- Data structure changes and new definitions for PBC.
- APIs to access PBC info.
- Remove unused code.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch enables support of new mezzanine cards for HP and IBM blade server.
- Add new pciids for HP and IBM mezzanine card.
- Add a new firmware image for HP mezzanine card, which is running in
FC only mode. Rename firmware image to reflect the difference. Change the
firmware download code accordingly for the above changes.
Signed-off-by: Jing Huang <huangj@brocade.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Eric Moore [Thu, 8 Jul 2010 20:44:34 +0000 (14:44 -0600)]
[SCSI] mpt2sas: driver fails to recover from injected PCIe bus errors
fixes surrounding PCIe enhanced error handling:
(1) We need to reject all request generated internaly inside the driver as well
as request arriving from the scsi mid layer when PCIe EEH is active. The fix is
to add a per adapter flag called pci_error_recovery which is checked thru out
the driver when request are generated.
(2) We don't need to call the pci_driver->remove directly from the PCIe
callbacks becuase its already called from the PCIe EEH code. In its place we are
shutting down the watchdog timer, and flushing back all pending IO.
(3) We need to save and restore the pci state across PCIe EEH handling.
Signed-off-by: Eric Moore <eric.moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This sysfs attribute is proven to be useful during pivot_root.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Eddie Wai [Thu, 1 Jul 2010 22:34:54 +0000 (15:34 -0700)]
[SCSI] bnx2i: Fixed the TCP graceful termination initiation
In compliance to RFC793, a TCP graceful termination will be used
instead of an abortive termination for the case where the remote
has initiated the close of the connection.
Additionally, a TCP abortive termination will be used to close the
connection when a logout response is not received in time after a
logout request has been initiated.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Eddie Wai [Thu, 1 Jul 2010 22:34:53 +0000 (15:34 -0700)]
[SCSI] bnx2i: Fine tuned conn destroy and context destroy timeout values
Added variables to separate the fine tuned timeout values for
connection destroy and context destroy for both 1g and 10g devices.
v2: Extended the 5771X disconnect timeout from 10s to 20s as the firmware
has a retransmission timeout of 16s. This fixes one of the iscsi_endpoint
leak issues when the target is slow or non-responsive to our TCP FIN.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Eddie Wai [Thu, 1 Jul 2010 22:34:52 +0000 (15:34 -0700)]
[SCSI] bnx2i: Optimized the bnx2i_stop connection clean up procedure
For cases where the iSCSI disconnection procedure times out due to
the iSCSI daemon being slow or unresponsive, the bnx2i_stop routine
will now perform hardware cleanup via bnx2i_hw_ep_disconnect on all
active endpoints so that subsequent operations will perform properly.
Also moved the mutex locks inside ep_connect and ep_disconnect so
that proper exclusivity can resolve simultaneous calls to the
ep_disconnect routine.
v2: Removed the unnecessary read lock in the bnx2i_stop
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Eddie Wai [Thu, 1 Jul 2010 22:34:51 +0000 (15:34 -0700)]
[SCSI] bnx2i: Created an active linklist which holds bnx2i endpoints
This introduces a new active linklist which would link up all active
bnx2i_endpoints. This will be used by subsequent patches that
follows.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Eddie Wai [Thu, 1 Jul 2010 22:34:50 +0000 (15:34 -0700)]
[SCSI] bnx2i: Separated the hardware's cleanup procedure from ep_disconnect
This patch introduces a new bnx2i_hw_ep_disconnect routine which
contains all chip related disconnect and clean up procedure of
iSCSI offload connections. This separation is intended as a
preparation for the subsequent bnx2i_stop patch.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[SCSI] scsi:hosts.c Fix warning: variable 'rval' set but not used
The below patch fixes a warning message generated by gcc 4.6.0
CC drivers/scsi/hosts.o
drivers/scsi/hosts.c: In function 'scsi_host_alloc':
drivers/scsi/hosts.c:328:6: warning: variable 'rval' set but not used
Fix this by removing the rval but placing a printk warning where it
would have been set.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Christie [Sun, 25 Apr 2010 12:03:57 +0000 (07:03 -0500)]
[SCSI] Log msg when getting Unit Attention
If the user accidentally changes LUN mappings or it occurs
due to a bug, then it can cause data corruption that can take
months and months to track down. This patch adds a log
message when getting REPORT_LUNS_DATA_CHANGED and it adds
a generic message for other Unit Attentions with asc == 0x3f.
We are working on adding support for handling of these errors,
but I think until then we should at least log a message so
tracking down problems as a result of one of these changes
is a little easier.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
if ((mptsas_find_vtarget(ioc, channel, id)) && !ioc->fw_events_off)
mptsas_queue_device_delete(...);
mptsas_queue_device_delete(), which must be called for
hot-removal, never gets called because mptsas_find_vtarget()
always returns 0 here. At that time, the vtarget has already
been freed in mptsas_target_destroy(), and also the scsi_device
has been marked as SDEV_DEL.
As a result of the issue, port deletion functions won't get
called and the device ends up being in an incomplete state.
(Some data structures and sysfs entries, which should be
removed in hot-removal, remain.) One side effect of this is
that a hot-addition of the device (bringing the device back
on) fails.
This patch just removes mptsas_find_vtarget() from the if-state
condition.
Wayne Boyer [Thu, 17 Jun 2010 18:51:40 +0000 (11:51 -0700)]
[SCSI] ipr: add MMIO write to perform BIST for 64 bit adapters
The 64 bit chip used in new adapters does not properly support the BIST register
in PCI config space. This patch implements an alternative MMIO write reset
method.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Nick Cheng [Tue, 13 Jul 2010 12:03:04 +0000 (20:03 +0800)]
[SCSI] SCSI: Support Type C RAID controller
1. To support Type C RAID controller, ACB_ADAPTER_TYPE_C, i.e. PCI device
ID: 0x1880. Signed-off-by: Nick Cheng< nick.cheng@areca.com.tw > Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Brian King [Thu, 17 Jun 2010 18:56:03 +0000 (13:56 -0500)]
[SCSI] ibmvscsi: Fix possible request_limit issue
If we encounter an error when sending a management datagram (i.e. non
SCSI command, such as virtual adapter initialization command), we
end up incrementing the request_limit, even though we don't decrement
it for these commands. Fix this up by doing this increment in
the error path for SRP commands only.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Brian King [Thu, 17 Jun 2010 18:56:02 +0000 (13:56 -0500)]
[SCSI] ibmvscsi: Fix error path deadlock
Fixes a deadlock that can occur if we hit a command timeout
during the virtual adapter initialization. The event done
functions are written with the assumption that no locks are held,
however, when purging requests this is not true. Fix up the
purge function to drop the lock so that the done function
is not called with the lock held, which can cause a deadlock.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Brian King [Thu, 17 Jun 2010 18:56:00 +0000 (13:56 -0500)]
[SCSI] ibmvscsi: Fix softlockup on resume
This fixes a softlockup seen on resume. During resume, the CRQ
must be reenabled. However, the H_ENABLE_CRQ hcall used to do
this may return H_BUSY or H_LONG_BUSY. When this happens, the
caller is expected to retry later. This patch changes a simple
loop, which was causing the softlockup, to a loop at task level
which sleeps between retries rather than simply spinning.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Brian King [Thu, 17 Jun 2010 18:55:13 +0000 (13:55 -0500)]
[SCSI] ibmvfc: Fix soft lockup on resume
This fixes a softlockup seen on resume. During resume, the CRQ
must be reenabled. However, the H_ENABLE_CRQ hcall used to do
this may return H_BUSY or H_LONG_BUSY. When this happens, the
caller is expected to retry later. Normally the H_ENABLE_CRQ
succeeds relatively soon. However, we have seen cases where
this can take long enough to see softlockup warnings.
This patch changes a simple loop, which was causing the
softlockup, to a loop at task level which sleeps between
retries rather than simply spinning.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Bandan Das [Wed, 16 Jun 2010 17:39:42 +0000 (13:39 -0400)]
[SCSI] mpt fusion: Cleanup some duplicate calls in mptbase.c
In mpt_detach, call to pci_set_drvdata is redundant because it
has already been called in mpt_adapter_disable. In mpt_attach,
ioc->pcidev is set to pdev two times.
Signed-off-by: Bandan Das <bandan.das@stratus.com> Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 09:11:48 +0000 (14:41 +0530)]
[SCSI] mptfusion: Added code for occationally SATA hotplug failure.
Issue: SATA hotplug does not work sometimes.
At the time of ADD device/ADD phys disk, drive may fail to add SATA device
due to temporary SAS Address for SATA device generated by firmware. Final
SAS address for SATA driver will be generated only after disk spinup is
done. This may take some times for slow spining SATA drives.
At phy link up driver gets attached device sas address and stores into
phyinfo. At the time of ADD event driver will read sas device page0 using
channel and FW ID provided in ADD Device event. Here in case of SATA drives,
driver will see miss match in phyinfo->sas_address and latest sas address
read from SAS DEVICE PAGE0 and eventually device won't be added to OS.
Fix:
When Driver read SAS DEVICE PAGE0, it can identify Device type looking at
device_info. If device is SATA drive and sas address mismatch happens,
Driver will do same stuffs which happened at the time of LINK UP to get
correct piece of information from Pages. ( Find parent device and refresh
parent device phys either HBA refresh/Exp refresh)
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 09:10:56 +0000 (14:40 +0530)]
[SCSI] mptfusion: schedule_target_reset from all Reset context
Issue:
target reset will be queued to driver's internal queue to get schedule
later. When driver add target into internal target_reset queue we will block IOs
on those target using scsi midlayer API. Now due to some cause driver is not
executing those target_reset list and it is always in block state.
Changes:
now we are clearing target_reset queue from all other Callback context
instead of only DeviceReset context.Now wherever driver is clearing
taskmgmt_in_progress flag it is considering target_reset queue cleanup
also.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 09:10:10 +0000 (14:40 +0530)]
[SCSI] mptfusion: Added sanity to check B_T mapping for device before adding to OS
Added sanity check before treating any device is a valid device.
It is possible that firmware can have device page0 in its table, but that
devicemay not be available in topology. Device will be available in topology
only if there is Bus Target mapping is done in firmware. Driver will always
check B_T mapping of firmware before reporting device to upper layer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 09:07:25 +0000 (14:37 +0530)]
[SCSI] mptfusion: Use DID_TRANSPORT_DISRUPTED instead of DID_BUS_BUSY
Changed the return value for Nexus Loss IOs to be DID_TRANSPORT_DISRUPTED.
What this will allow is the multi-path driver to delay the fail over
process. They would like the path to keep up as long as the nexus loss
Loginfo is return from firmware. With DID_BUS_BUSY the path fails over
immediately.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 09:05:46 +0000 (14:35 +0530)]
[SCSI] mptfusion: Set fw_events_off to 1 at driver load time.
fw_events_off is flag checking for driver to do Event handling or not.
Normally it should be OFF at the time of initialization. Only enable it at
the time of INTR enable of device first time. This will always occur only
after resource allocation.
ioc->fw_events_off = 1 is set in mpt_attach()
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:20:11 +0000 (13:50 +0530)]
[SCSI] mpt2sas: Copy message frame before releasing to free pool to have a local reference.
Current driver is not clearing the per device tm_busy flag
following the Task Mangement request completion from the IOCTL path.
When this flag is set, the IO queues are frozen. The reason the flag
didn't get cleared is becuase the driver is referencing
memory associated to the mpi request following the completion, when
the memory had been reallocated for a new request. When the memory
was reallocated, the driver didn't clear the flag becuase it was
expecting a task managment reqeust, and the reallocated request was
for SCSI_IO. To fix the problem the driver needs to have a cached
backup copy of the original reqeust.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:19:28 +0000 (13:49 +0530)]
[SCSI] mpt2sas: Copy sense buffer instead of working on direct memory location
(1) driver was not setting the sense data size prior to sending SCSI_IO,
resulting in the 0x31190000 loginfo
(2) The driver needs to copy the sense data to local buffer prior
to releasing the request message frame. If not, the sense buffer gets
overwritten by the next SCSI_IO request.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:18:46 +0000 (13:48 +0530)]
[SCSI] mpt2sas: Adding additional message to error escalation callback
Adding additional messages to the error escallation callbacks which
displays the wwid, sas address, handle, phy number, enclosure logical id,
and slot. In the same eh callbacks, routines, the printks were converted
to sdev_printks, which displays the bus target mapping. These additional
modifications help better identify the device which is in recovery.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:18:10 +0000 (13:48 +0530)]
[SCSI] mpt2sas: Add additional check for responding volumes after Host Reset
ISSUE DESCRIPTION:
This test case involves creating two RAID1 volumes, then
simultaneiously issue host reset and pull all the drives associated to
the 1st raid volume. The observed behavour is the physical drives are
removed, however the volume remains. The expected behavour is the
volume as well as physical drives should be removed from OS.
FIX:
Add support in the post host reset device scan logic for raid volumes
where the driver will have an additional check for responding raid
volume where the status should be either online, optimal, or degraded.
So for voluemes that have a status of missing or failed, the driver
will mark them for deletion.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:17:29 +0000 (13:47 +0530)]
[SCSI] mpt2sas: Added -ENOMEM return type when allocation fails
In the driver mpt2sas_base_attach subroutine, we need to add
support to return the proper error code when there are memory allocation
failures, e.g. returning -ENOMEM.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:16:13 +0000 (13:46 +0530)]
[SCSI] mpt2sas: Redesign Raid devices event handling using pd_handles per HBA
Actual problem :
Driver may receiving the top level expander
removal event prior to all the individual PD removal events, hence the
driver is breaking down all the PDs in advanced to the actaul PD UNHIDE
event. Driver sends multiple
Target Resets to the same volume handle for each individual PD removal.
FIX DESCRIPTION:
To fix this issue, the entire PD device handshake protocal has to be
moved to interrupt context so the breakdown occurs immediately after the
actual UNHIDE event arrives. The driver will only issue one Target Reset to
the volume handle, occurring after the FAILED or MISSING volume status
event arrives from interrupt context. For the PD UNHIDE event, the driver
will issue target resets to the PD handles, followed by OP_REMOVE. The
driver will set the "deteleted" flag during interrupt context. A "pd_handle"
bitmask was introduced so the driver has a list of known pds during entire
life of the PD; this replaces the "hidden_raid_component" flag handle in
the sas_device object. Each bit in the bitmask represents a device handle.
The bit in the bitmask would be toggled ON/OFF when the HIDE/UNHIDE
events arrive; also this pd_handle bitmask would bould be refreshed
across host resets.
Here we kept older behavior of sending target reset to volume when there is
a single drive pull, wait for the reply, then send target resets
to the PDs. We kept this behavior so the driver will
behave the same for older versions of firmware.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:15:17 +0000 (13:45 +0530)]
[SCSI] mpt2sas: Tie a log info message to a specific PHY.
Add support to display additional debug info for SCSI_IO and
RAID_SCSI_IO_PASSTHROUGH sent from the normal entry queued entry
point, as well as internal generated commands, and IOCTLS. The
additional debug info included the phy number, as well as the
sas address, enclosure logical id, and slot number. This debug info
has to be enabled thru the logging_level command line option, by
default this will not be displayed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:13:17 +0000 (13:43 +0530)]
[SCSI] mpt2sas: Added sysfs support for trace buffer
Added support so the diag ring buffer can be pulled via sysfs
Added three new shost attributes: host_trace_buffer,
host_trace_buffer_enable, and host_trace_buffer_size. The
host_trace_buffer_enable attribute is used to either post or release
the trace buffers. The host_trace_buffer_size attribute contains
the size of the trace buffer. The host_trace_buffer atttribute contains
a maximum 4KB window of the buffer. In order to read the entire host buffer,
you will need to write the offset to host_trace_buffer prior to reading
it. release the host buffer, then write the entire host buffer contents to
a file.
In addition to this enhancement, we moved the automatic posting of host buffers
at driver load time to be called prior to port_enable, instead of after.
That way discovery is available in the host buffer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:04:31 +0000 (13:34 +0530)]
[SCSI] mpt2sas: Added expander phy control support
Added support to send link resets, hard resets, enable/disable phys, and
changing link rates for for expanders. This will be exported to
attributes within the sas transport layer. A new wrapper function was
added for sending SMP passthru to expanders for phy control.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Thu, 17 Jun 2010 08:02:54 +0000 (13:32 +0530)]
[SCSI] mpt2sas: Added expander phy counter support
Added support to retrieve the invalid_dword_count,
running_disparity_error_count, loss_of_dword_sync_count, and
phy_reset_problem_count for expanders. This will be exported to
attributes within the sas transport layer. A new wrapper function was
added for sending SMP passthru to retrieve the expander phy error log.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
projects / linux-beck.git / log