Filesystem shutdown testing on an older distro kernel has uncovered an
imbalanced locking pattern for the inode flush lock in
xfs_reclaim_inode(). Specifically, there is a double unlock sequence
between the call to xfs_iflush_abort() and xfs_reclaim_inode() at the
"reclaim:" label.
This actually does not cause obvious problems on current kernels due to
the current flush lock implementation. Older kernels use a counting
based flush lock mechanism, however, which effectively breaks the lock
indefinitely when an already unlocked flush lock is repeatedly unlocked.
Though this only currently occurs on filesystem shutdown, it has
reproduced the effect of elevating an fs shutdown to a system-wide crash
or hang.
As it turns out, the flush lock is not actually required for the reclaim
logic in xfs_reclaim_inode() because by that time we have already cycled
the flush lock once while holding ILOCK_EXCL. Therefore, remove the
additional flush lock/unlock cycle around the 'reclaim:' label and
update branches into this label to release the flush lock where
appropriate. Add an assert to xfs_ifunlock() to help prevent future
occurences of the same problem.
Reported-by: Zorro Lang <zlang@redhat.com> Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[dchinner: cleaned up XFS_MIN_CRC_BLOCKSIZE check]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
is all over the xfs code; provide a new helper
xfs_iext_count(ifp) to count the number of inline extents
in an inode fork.
[dchinner: pick up several missed conversions]
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've had reports of generic/095 causing XFS to BUG() in
__xfs_get_blocks() due to the existence of delalloc blocks on a
direct I/O read. generic/095 issues a mix of various types of I/O,
including direct and memory mapped I/O to a single file. This is
clearly not supported behavior and is known to lead to such
problems. E.g., the lack of exclusion between the direct I/O and
write fault paths means that a write fault can allocate delalloc
blocks in a region of a file that was previously a hole after the
direct read has attempted to flush/inval the file range, but before
it actually reads the block mapping. In turn, the direct read
discovers a delalloc extent and cannot proceed.
While the appropriate solution here is to not mix direct and memory
mapped I/O to the same regions of the same file, the current
BUG_ON() behavior is probably overkill as it can crash the entire
system. Instead, localize the failure to the I/O in question by
returning an error for a direct I/O that cannot be handled safely
due to delalloc blocks. Be careful to allow the case of a direct
write to post-eof delalloc blocks. This can occur due to speculative
preallocation and is safe as post-eof blocks are not accompanied by
dirty pages in pagecache (conversely, preallocation within eof must
have been zeroed, and thus dirtied, before the inode size could have
been increased beyond said blocks).
Finally, provide an additional warning if a direct I/O write occurs
while the file is memory mapped. This may not catch all problematic
scenarios, but provides a hint that some known-to-be-problematic I/O
methods are in use.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cowblocks background scanner currently clears the cowblocks tag
for inodes without any real allocations in the cow fork. This
excludes inodes with only delalloc blocks in the cow fork. While we
might never expect to clear delalloc blocks from the cow fork in the
background scanner, it is not necessarily correct to clear the
cowblocks tag from such inodes.
For example, if the background scanner happens to process an inode
between a buffered write and writeback, the scanner catches the
inode in a state after delalloc blocks have been allocated to the
cow fork but before the delalloc blocks have been converted to real
blocks by writeback. The background scanner then incorrectly clears
the cowblocks tag, even if part of the aforementioned delalloc
reservation will not be remapped to the data fork (i.e., extra
blocks due to the cowextsize hint). This means that any such
additional blocks in the cow fork might never be reclaimed by the
background scanner and could persist until the inode itself is
reclaimed.
To address this problem, only skip and clear inodes without any cow
fork allocations whatsoever from the background scanner. While we
generally do not want to cancel delalloc reservations from the
background scanner, the pagecache dirty check following the
cowblocks check should prevent that situation. If we do end up with
delalloc cow fork blocks without a dirty address space mapping, this
is probably an indication that something has gone wrong and the
blocks should be reclaimed, as they may never be converted to a real
allocation.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the return value of xfs_trans_reserve_quota_nblks for errors.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel commit 5ef828c4 ("xfs: avoid false quotacheck after unclean
shutdown") made xfs_sb_from_disk() also call xfs_sb_quota_from_disk
by default.
However, when this was merged to libxfs, existing separate
calls to libxfs_sb_quota_from_disk remained, and calling it
twice in a row on a V4 superblock leads to issues, because:
and after the second call, we have set both pquotino and gquotino
to NULLFSINO.
Fix this by making it safe to call twice, and also remove the extra
calls to libxfs_sb_quota_from_disk.
This is only spotted when running xfstests with "-m crc=0" because
the sb_from_disk change came about after V5 became default, and
the above behavior only exists on a V4 superblock.
Reported-by: Eryu Guan <eguan@redhat.com> Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the TPM we're connecting to uses a static burst count, it will report
a burst count of zero throughout the response read. However, get_burstcount
assumes that a response of zero indicates that the TPM is not ready to
receive more data. In this case, it returns a negative error code, which
is passed on to tpm_tis_{write,read}_bytes as a u16, causing
them to read/write far too many bytes.
This patch checks for negative return codes and bails out from recv_data
and tpm_tis_send_data.
Fixes: 1107d065fdf1 (tpm_tis: Introduce intermediate layer for TPM access) Signed-off-by: Josh Zimmerman <joshz@google.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous spec version said "double Ytile planes minimum lines",
and I interpreted this as referring to what the spec calls "Y tile
minimum", but in fact it was referring to what the spec calls "Minimum
Scanlines for Y tile". I noticed that Mahesh Kumar had a different
interpretation, so I sent and email to the spec authors and got
clarification on the correct meaning. Also, BSpec was updated and
should be clear now.
Fixes: ee3d532fcb64 ("drm/i915/gen9: unconditionally apply the memory bandwidth WA") Cc: stable@vger.kernel.org Cc: Mahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1478636531-6081-1-git-send-email-paulo.r.zanoni@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mahesh Kumar is already working on a proper implementation for the
workaround, but while we still don't have it, let's just
unconditionally apply the workaround for everybody and we hope we can
close all those numerous bugzilla tickets. Also, I'm not sure how easy
it will be to backport the final implementation to the stable Kernels,
and this patch here is probably easier to backport.
At the present moment I still don't have confirmation that this patch
fixes any of the bugs listed below, but we should definitely try
testing all of them again.
v2: s/intel_needs_memory_bw_wa/skl_needs_memory_bw_wa/ (Lyude).
v3: Rebase (dev -> dev_priv change on ilk_wm_max_level).
We've been ignoring the poor bugzilla reporters that say PSR causes
system lockups and all other sorts of problems. The earliest bug
report is from April, so I think we can use the "revert the offending
commit if no fixes are presented within 8 months" rule here.
Fixes: 9b58e352b463 ("drm/i915: Enable PSR by default on Haswell and Broadwell.")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97602
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97515
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96736
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96704
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96569
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95176
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94985 Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Jim Bride <jim.bride@linux.intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1481662664-18986-1-git-send-email-paulo.r.zanoni@intel.com
(cherry picked from commit 2ee7dc497e348eecbb82adbb1ea9e9a7e29fe921) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were storing viewport relative coordinates for AVIVO/DCE display
engines. However, radeon_crtc_cursor_set2 and radeon_cursor_reset pass
radeon_crtc->cursor_x/y as the x/y parameters of
radeon_cursor_move_locked, which would break if the CRTC isn't located
at (0, 0).
Cc: stable@vger.kernel.org Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__s390_dma_map_sg maps a dma-contiguous area. Although we only map
whole pages we have to take into account that the area doesn't start
or stop at a page boundary because we use the dma address to loop
over the individual sg entries. Failing to do that might lead to an
access of the wrong sg entry.
Fixes: ee877b81c6b9 ("s390/pci_dma: improve map_sg") Reported-and-tested-by: Christoph Raisch <raisch@de.ibm.com> Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The s390 specific sched_domain_topology_level should always be used,
not only if the machine provides topology information. Luckily this
odd behaviour, that was by accident introduced with git commit d05d15da18f5 ("s390/topology: delay initialization of topology cpu
masks") has currently no side effect.
Fixes: d05d15da18f5 ("s390/topology: delay initialization of topology cpumasks") Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is at least one Chelsio 10Gb card which uses VPD area to store some
non-standard blocks (example below). However pci_vpd_size() returns the
length of the first block only assuming that there can be only one VPD "End
Tag".
Since 4e1a635552d3 ("vfio/pci: Use kernel VPD access functions"), VFIO
blocks access beyond that offset, which prevents the guest "cxgb3" driver
from probing the device. The host system does not have this problem as its
driver accesses the config space directly without pci_read_vpd().
Add a quirk to override the VPD size to a bigger value. The maximum size
is taken from EEPROMSIZE in drivers/net/ethernet/chelsio/cxgb3/common.h.
We do not read the tag as the cxgb3 driver does as the driver supports
writing to EEPROM/VPD and when it writes, it only checks for 8192 bytes
boundary. The quirk is registered for all devices supported by the cxgb3
driver.
This adds a quirk to the PCI layer (not to the cxgb3 driver) as the cxgb3
driver itself accesses VPD directly and the problem only exists with the
vfio-pci driver (when cxgb3 is not running on the host and may not be even
loaded) which blocks accesses beyond the first block of VPD data. However
vfio-pci itself does not have quirks mechanism so we add it to PCI.
This is the controller:
Ethernet controller [0200]: Chelsio Communications Inc T310 10GbE Single Port Adapter [1425:0030]
This is what I parsed from its VPD:
===
b'\x82*\x0010 Gigabit Ethernet-SR PCI Express Adapter\x90J\x00EC\x07D76809 FN\x0746K'
0000 Large item 42 bytes; name 0x2 Identifier String
b'10 Gigabit Ethernet-SR PCI Express Adapter'
002d Large item 74 bytes; name 0x10
#00 [EC] len=7: b'D76809 '
#0a [FN] len=7: b'46K7897'
#14 [PN] len=7: b'46K7897'
#1e [MN] len=4: b'1037'
#25 [FC] len=4: b'5769'
#2c [SN] len=12: b'YL102035603V'
#3b [NA] len=12: b'00145E992ED1'
007a Small item 1 bytes; name 0xf End Tag
Mellanox devices were marked as having INTx masking ability broken. As a
result, the VFIO driver fails to start when more than one device function
is passed-through to a VM if both have the same INTx pin.
Prior to Connect-IB, Mellanox devices exposed to the operating system one
PCI function per all ports. Starting from Connect-IB, the devices are
function-per-port. When passing the second function to a VM, VFIO will
fail to start.
Exclude ConnectX-4, ConnectX4-Lx and Connect-IB from the list of Mellanox
devices marked as having broken INTx masking:
- ConnectX-4 and ConnectX4-LX firmware version is checked. If INTx
masking is supported, we unmark the broken INTx masking.
- Connect-IB does not support INTx currently so will not cause any
problem.
[bhelgaas: call pci_disable_device() always, after iounmap()] Fixes: 11e42532ada3 ("PCI: Assume all Mellanox devices have broken INTx masking") Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're trying to mask out bits[23:8] while retaining [32:24, 7:0], but we're
doing the inverse. That doesn't have too much effect, since we're setting
all the [23:8] bits to 1, and the other bits are only relevant for modes
we're currently not using. But we should get this right.
The calculation of negotiated lanes is wrong: it should be shifted by
PCIE_CORE_PL_CONF_LANE_SHIFT, but it is shifted by
PCIE_CORE_PL_CONF_LANE_MASK instead. Let's fix it.
gcc is unsure about the use of last_ofs_in_node, which might happen
without a prior initialization:
fs/f2fs//git/arm-soc/fs/f2fs/data.c: In function ‘f2fs_map_blocks’:
fs/f2fs/data.c:799:54: warning: ‘last_ofs_in_node’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (prealloc && dn.ofs_in_node != last_ofs_in_node + 1) {
As pointed out by Chao Yu, the code is actually correct as 'prealloc'
is only set if the last_ofs_in_node has been set, the two always
get updated together.
This initializes last_ofs_in_node to dn.ofs_in_node for each
new dnode at the start of the 'next_block' loop, which at that
point is a correct initialization as well. I assume that compilers
that correctly track the contents of the variables and do not
warn about the condition also figure out that they can eliminate
the extra assignment here.
Fixes: 46008c6d4232 ("f2fs: support in batch multi blocks preallocation") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
md_open() gets a counted reference on an mddev using mddev_find().
If it ends up returning an error, it must drop this reference.
There are two error paths where the reference is not dropped.
One only happens if the process is signalled and an awkward time,
which is quite unlikely.
The other was introduced recently in commit af8d8e6f0.
Change the code to ensure the drop the reference when returning an error,
and make it harded to re-introduce this sort of bug in the future.
Reported-by: Marc Smith <marc.smith@mcc.edu> Fixes: af8d8e6f0315 ("md: changes for MD_STILL_CLOSED flag") Signed-off-by: NeilBrown <neilb@suse.com> Acked-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core AES cipher implementation that uses ARMv8 Crypto Extensions
instructions erroneously loads the round keys as 64-bit quantities,
which causes the algorithm to fail when built for big endian. In
addition, the key schedule generation routine fails to take endianness
into account as well, when loading the combining the input key with
the round constants. So fix both issues.
Fixes: 12ac3efe74f8 ("arm64/crypto: use crypto instructions to generate AES key schedule") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SHA1 digest is an array of 5 32-bit quantities, so we should refer
to them as such in order for this code to work correctly when built for
big endian. So replace 16 byte scalar loads and stores with 4x4 vector
ones where appropriate.
Fixes: 2c98833a42cd ("arm64/crypto: SHA-1 using ARMv8 Crypto Extensions") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AES implementation using pure NEON instructions relies on the generic
AES key schedule generation routines, which store the round keys as arrays
of 32-bit quantities stored in memory using native endianness. This means
we should refer to these round keys using 4x4 loads rather than 16x1 loads.
In addition, the ShiftRows tables are loading using a single scalar load,
which is also affected by endianness, so emit these tables in the correct
order depending on whether we are building for big endian or not.
Fixes: 49788fe2a128 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AES-CCM implementation that uses ARMv8 Crypto Extensions instructions
refers to the AES round keys as pairs of 64-bit quantities, which causes
failures when building the code for big endian. In addition, it byte swaps
the input counter unconditionally, while this is only required for little
endian builds. So fix both issues.
Fixes: 12ac3efe74f8 ("arm64/crypto: use crypto instructions to generate AES key schedule") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AES key schedule generation is mostly endian agnostic, with the
exception of the rotation and the incorporation of the round constant
at the start of each round. So implement a big endian specific version
of that part to make the whole routine big endian compatible.
Fixes: 86464859cc77 ("crypto: arm - AES in ECB/CBC/CTR/XTS modes using ARMv8 Crypto Extensions") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GHASH key and digest are both pairs of 64-bit quantities, but the
GHASH code does not always refer to them as such, causing failures when
built for big endian. So replace the 16x1 loads and stores with 2x8 ones.
Fixes: b913a6404ce2 ("arm64/crypto: improve performance of GHASH algorithm") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SHA256 digest is an array of 8 32-bit quantities, so we should refer
to them as such in order for this code to work correctly when built for
big endian. So replace 16 byte scalar loads and stores with 4x32 vector
ones where appropriate.
Fixes: 6ba6c74dfc6b ("arm64/crypto: SHA-224/SHA-256 using ARMv8 Crypto Extensions") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We added some new locking but forgot to unlock on error.
Fixes: 57127645d79d ("s390/zcrypt: Introduce new SHA-512 based Pseudo Random Generator.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit bda807d44454 ("mm: migrate: support non-lru movable page
migration") isolate_migratepages_block) can isolate !PageLRU pages which
would acct_isolated account as NR_ISOLATED_*. Accounting these non-lru
pages NR_ISOLATED_{ANON,FILE} doesn't make any sense and it can misguide
heuristics based on those counters such as pgdat_reclaimable_pages resp.
too_many_isolated which would lead to unexpected stalls during the
direct reclaim without any good reason. Note that
__alloc_contig_migrate_range can isolate a lot of pages at once.
On mobile devices such as 512M ram android Phone, it may use a big zram
swap. In some cases zram(zsmalloc) uses too many non-lru but
migratedable pages, such as:
MemTotal: 468148 kB
Normal free:5620kB
Free swap:4736kB
Total swap:409596kB
ZRAM: 164616kB(zsmalloc non-lru pages)
active_anon:60700kB
inactive_anon:60744kB
active_file:34420kB
inactive_file:37532kB
Fix this by only accounting lru pages to NR_ISOLATED_* in
isolate_migratepages_block right after they were isolated and we still
know they were on LRU. Drop acct_isolated because it is called after
the fact and we've lost that information. Batching per-cpu counter
doesn't make much improvement anyway. Also make sure that we uncharge
only LRU pages when putting them back on the LRU in
putback_movable_pages resp. when unmap_and_move migrates the page.
[mhocko@suse.com: replace acct_isolated() with direct counting] Fixes: bda807d44454 ("mm: migrate: support non-lru movable page migration") Link: http://lkml.kernel.org/r/20161019080240.9682-1-mhocko@kernel.org Signed-off-by: Ming Ling <ming.ling@spreadtrum.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Minchan Kim <minchan@kernel.org> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The radix tree counts valid entries in each tree node. Entries stored
in the tree cannot be removed by simpling storing NULL in the slot or
the internal counters will be off and the node never gets freed again.
When collapsing a shmem page fails, restore the holes that were filled
with radix_tree_insert() with a proper radix tree deletion.
Fixes: f3f0e1d2150b ("khugepaged: add support of collapse for tmpfs/shmem pages") Link: http://lkml.kernel.org/r/20161117191138.22769-3-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Jan Kara <jack@suse.cz> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Matthew Wilcox <mawilcox@linuxonhyperv.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "mm: workingset: radix tree subtleties & single-page file
refaults", v3.
This is another revision of the radix tree / workingset patches based on
feedback from Jan and Kirill.
This is a follow-up to d3798ae8c6f3 ("mm: filemap: don't plant shadow
entries without radix tree node"). That patch fixed an issue that was
caused mainly by the page cache sneaking special shadow page entries
into the radix tree and relying on subtleties in the radix tree code to
make that work. The fix also had to stop tracking refaults for
single-page files because shadow pages stored as direct pointers in
radix_tree_root->rnode weren't properly handled during tree extension.
These patches make the radix tree code explicitely support and track
such special entries, to eliminate the subtleties and to restore the
thrash detection for single-page files.
This patch (of 9):
When a radix tree iteration drops the tree lock, another thread might
swoop in and free the node holding the current slot. The iteration
needs to do another tree lookup from the current index to continue.
[kirill.shutemov@linux.intel.com: re-lookup for replacement] Fixes: f3f0e1d2150b ("khugepaged: add support of collapse for tmpfs/shmem pages") Link: http://lkml.kernel.org/r/20161117191138.22769-2-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Matthew Wilcox <mawilcox@linuxonhyperv.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PDF build on Kernel 4.9-rc? returns an error with Sphinx 1.3.x
and Sphinx 1.4.x, when trying to solve some cross-references.
The solution is to redefine the \DURole macro.
However, this is redefined too late. Move such redefinition to
LaTeX preamble and bind it to just the Sphinx versions where the
error is known to be present.
Tested by building the documentation on interactive mode:
make PDFLATEX=xelatex -C Documentation/output/./latex
Fixes: e61a39baf74d ("[media] index.rst: Fix LaTeX error in interactive mode on Sphinx 1.4.x") Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot use the pte value used in set_pte_at for pte_same comparison,
because archs like ppc64, filter/add new pte flag in set_pte_at.
Instead fetch the pte value inside hugetlb_cow. We are comparing pte
value to make sure the pte didn't change since we dropped the page table
lock. hugetlb_cow get called with page table lock held, and we can take
a copy of the pte value before we drop the page table lock.
With hugetlbfs, we optimize the MAP_PRIVATE write fault path with no
previous mapping (huge_pte_none entries), by forcing a cow in the fault
path. This avoid take an addition fault to covert a read-only mapping
to read/write. Here we were comparing a recently instantiated pte (via
set_pte_at) to the pte values from linux page table. As explained above
on ppc64 such pte_same check returned wrong result, resulting in us
taking an additional fault on ppc64.
Fixes: 6a119eae942c ("powerpc/mm: Add a _PAGE_PTE bit") Link: http://lkml.kernel.org/r/20161018154245.18023-1-aneesh.kumar@linux.vnet.ibm.com Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Reported-by: Jan Stancek <jstancek@redhat.com> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 34c3d9819fda ("genirq/affinity: Provide smarter irq spreading
infrastructure") introduced a better IRQ spreading mechanism, taking
account of the available NUMA nodes in the machine.
Problem is that the algorithm of retrieving the nodemask iterates
"linearly" based on the number of online nodes - some architectures
present non-linear node distribution among the nodemask, like PowerPC.
If this is the case, the algorithm lead to a wrong node count number
and therefore to a bad/incomplete IRQ affinity distribution.
For example, this problem were found in a machine with 128 CPUs and two
nodes, namely nodes 0 and 8 (instead of 0 and 1, if it was linearly
distributed). This led to a wrong affinity distribution which then led to
a bad mq allocation for nvme driver.
Finally, we take the opportunity to fix a comment regarding the affinity
distribution when we have _more_ nodes than vectors.
Fixes: 34c3d9819fda ("genirq/affinity: Provide smarter irq spreading infrastructure") Reported-by: Gabriel Krisman Bertazi <gabriel@krisman.be> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Gabriel Krisman Bertazi <gabriel@krisman.be> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Cc: linux-pci@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: hch@lst.de Link: http://lkml.kernel.org/r/1481738472-2671-1-git-send-email-gpiccoli@linux.vnet.ibm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed some wakeirq flakeyness with consumer drivers not using
autosuspend. For drivers not using autosuspend, the wakeirq may never
get unmasked in rpm_suspend() because of irq desc->depth.
We are configuring dedicated wakeirqs to start with IRQ_NOAUTOEN as we
naturally don't want them running until rpm_suspend() is called.
However, when a consumer driver initially calls pm_runtime_get(), we
now wrongly start with disable_irq_nosync() call on the dedicated
wakeirq that is disabled to start with.
This causes desc->depth to toggle between 1 and 2 instead of the usual
0 and 1. This can prevent enable_irq() from unmasking the wakeirq as
that only happens at desc->depth 1.
This does not necessarily show up with drivers using autosuspend as
there is time for disable_irq_nosync() before rpm_suspend() gets called
after the autosuspend timeout.
Let's fix the issue by adding wirq->status that lazily gets set on
the first rpm_suspend(). We also need PM runtime core private functions
for dev_pm_enable_wake_irq_check() and dev_pm_disable_wake_irq_check()
so we can enable the dedicated wakeirq on the first rpm_suspend().
While at it, let's also fix the comments for dev_pm_enable_wake_irq()
and dev_pm_disable_wake_irq(). Those can still be used by the consumer
drivers as needed because the IRQ core manages the interrupt usecount
for us.
Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling) Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We did not implement an irq_cpu_offline callback for our irqchip, yet we
support setting a given IRQ's affinity. This resulted in interrupts
whose affinity mask included CPUs being taken offline not to work
correctly once the CPU had been put offline.
When the "policy" securityfs file is opened for read, it is opened as a
sequential file. However, when it is eventually released, there is no
cleanup for the sequential file, therefore some memory is leaked.
This patch adds a call to seq_release() in ima_release_policy() to clean up
the memory when the file is opened for read.
Fixes: 80eae209d63a IMA: allow reading back the current policy Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com> Tested-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complains that we started using the array offset before we
checked that it was valid.
Fixes: 017c59c042d0 ('relay: Use per CPU constructs for the relay channel buffer pointers') Link: http://lkml.kernel.org/r/20161013084947.GC16198@mwanda Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This iscsit_tpg_add_portal_group() function is only called from
lio_target_tiqn_addtpg(). Both functions free the "tpg" pointer on
error so it's a double free bug. The memory is allocated in the caller
so it should be freed in the caller and not here.
Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: David Disseldorp <ddiss@suse.de>
[ bvanassche: Added "Fix" at start of patch title ] Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-7 notices that the condition in mvs_94xx_command_active looks
suspicious:
drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active':
drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
This was introduced when the mv_printk() statement got added, and leads
to the condition being ignored. This is probably harmless.
Changing '&&' to '&' makes the code look reasonable, as we check the
command bit before setting and printing it.
Fixes: a4632aae8b66 ("[SCSI] mvsas: Add new macros and functions") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a SW-configurable card is specified but not found, the driver
releases wrong region, causing the following message in kernel log:
Trying to free nonexistent resource <0000000000000000-000000000000000f>
Fix it by assigning base earlier.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Fixes: a8cfbcaec0c1 ("scsi: g_NCR5380: Stop using scsi_module.c") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately, I seem to have missed a case where an IRQ safe spinlock was
required, in samsung_i2s_dai_remove, when I fixed up the other calls in
this patch:
316fa9e09ad7 ("ASoC: samsung: Use IRQ safe spin lock calls")
This causes a lockdep warning when unbinding and rebinding the audio card:
Fixes: ce8bcdbb61d9 ("ASoC: samsung: i2s: Protect more registers with a spinlock") Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cht_bsw_rt5645 driver allocates the own codec_id string but doesn't
release it. For simplicity, put the string in cht_mc_private; then
the string is allocated in a shot and released altogether.
Fixes: c8560b7c917f ("ASoC: cht_bsw_rt5645: Fix writing to string literal") Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bugfix accidentally removed the implicit initialization of the
dma channel number, causing undefined behavior when
v->alloc_dma_channel is NULL:
sound/soc/qcom/lpass-platform.c: In function ‘lpass_platform_pcmops_open’:
sound/soc/qcom/lpass-platform.c:83:29: error: ‘dma_ch’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds back an explicit initialization to zero, restoring the
previous behavior for that case.
Fixes: 022d00ee0b55 ("ASoC: lpass-platform: Fix broken pcm data usage") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Kenneth Westfield <kwestfie@codeaurora.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We met the DMAR fault both on hpsa P420i and P421 SmartArray controllers
under kdump, it can be steadily reproduced on several different machines,
the dmesg log is like:
HP HPSA Driver (v 3.4.16-0)
hpsa 0000:02:00.0: using doorbell to reset controller
hpsa 0000:02:00.0: board ready after hard reset.
hpsa 0000:02:00.0: Waiting for controller to respond to no-op
DMAR: Setting identity map for device 0000:02:00.0 [0xe8000 - 0xe8fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xf4000 - 0xf4fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6e000 - 0xbdf6efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6f000 - 0xbdf7efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf7f000 - 0xbdf82fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf83000 - 0xbdf84fff]
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [02:00.0] fault addr fffff000 [fault reason 06] PTE Read access is not set
hpsa 0000:02:00.0: controller message 03:00 timed out
hpsa 0000:02:00.0: no-op failed; re-trying
After some debugging, we found that the fault addr is from DMA initiated at
the driver probe stage after reset(not in-flight DMA), and the corresponding
pte entry value is correct, the fault is likely due to the old iommu caches
of the in-flight DMA before it.
Thus we need to flush the old cache after context mapping is setup for the
device, where the device is supposed to finish reset at its driver probe
stage and no in-flight DMA exists hereafter.
I'm not sure if the hardware is responsible for invalidating all the related
caches allocated in the iommu hardware before, but seems not the case for hpsa,
actually many device drivers have problems in properly resetting the hardware.
Anyway flushing (again) by software in kdump kernel when the device gets context
mapped which is a quite infrequent operation does little harm.
With this patch, the problematic machine can survive the kdump tests.
CC: Myron Stowe <myron.stowe@gmail.com> CC: Joseph Szczypek <jszczype@redhat.com> CC: Don Brace <don.brace@microsemi.com> CC: Baoquan He <bhe@redhat.com> CC: Dave Young <dyoung@redhat.com> Fixes: 091d42e43d21 ("iommu/vt-d: Copy translation tables from old kernel") Fixes: dbcd861f252d ("iommu/vt-d: Do not re-use domain-ids from the old kernel") Fixes: cf484d0e6939 ("iommu/vt-d: Mark copied context entries") Signed-off-by: Xunlei Pang <xlpang@redhat.com> Tested-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Different encodings are used to represent supported PASID bits
and number of PASID table entries.
The current code assigns ecap_pss directly to extended context
table entry PTS which is wrong and could result in writing
non-zero bits to the reserved fields. IOMMU fault reason
11 will be reported when reserved bits are nonzero.
This patch converts ecap_pss to extend context entry pts encoding
based on VT-d spec. Chapter 9.4 as follows:
- number of PASID bits = ecap_pss + 1
- number of PASID table entries = 2^(pts + 5)
Software assigned limit of pasid_max value is also respected to
match the allocation limitation of PASID table.
cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
cc: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Tested-by: Mika Kuoppala <mika.kuoppala@intel.com> Fixes: 2f26e0a9c9860 ('iommu/vt-d: Add basic SVM PASID support') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic command buffer entry is 128 bits (16 bytes), so the offset
of tail and head pointer should be 16 bytes aligned and increased with
0x10 per command.
When cmd buf is full, head = (tail + 0x10) % CMD_BUFFER_SIZE.
So when left space of cmd buf should be able to store only two
command, we should be issued one COMPLETE_WAIT additionally to wait
all older commands completed. Then the left space should be increased
after IOMMU fetching from cmd buf.
So left check value should be left <= 0x20 (two commands).
The RZ/A1 is different than the other Renesas SOCs because the MSTP
registers are 8-bit instead of 32-bit and if you try writing values as
32-bit nothing happens...meaning this driver never worked for r7s72100.
Function mx31_clocks_init() is called during clock intialization on
legacy boards with reference clock frequency passed as its input
argument, this can be verified by examination of the function
declaration found in arch/arm/mach-imx/common.h and actual function
users which include that header file.
Inside CCF driver the function ignores its input argument, by chance
the used value in the function body is the same as input arguments on
side of all callers.
Fixes: d9388c843237 ("clk: imx31: Do not call mxc_timer_init twice when booting with DT") Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The audio module clocks are supposed to be set according to the sample
rate of the audio stream. The audio PLL provides the clock signal for
these module clocks, and only it is freely tunable.
Set CLK_SET_RATE_PARENT for the audio module clocks so their users can
properly tune the clock rate.
The audio module clocks are supposed to be set according to the sample
rate of the audio stream. The audio PLL provides the clock signal for
these module clocks, and only it is freely tunable.
Set CLK_SET_RATE_PARENT for the audio module clocks so their users can
properly tune the clock rate.
Fix bug https://bugzilla.kernel.org/show_bug.cgi?id=188561. Function
wm831x_clkout_is_prepared() returns "true" when it fails to read
CLOCK_CONTROL_1. "true" means the device is already prepared. So
return "true" on the read failure seems improper.
Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Fixes: f05259a6ffa4 ("clk: wm831x: Add initial WM831x clock driver") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks on these boards run at 25 MHz, not 19.2 and 27 like
other platforms. Unfortunately I copy/pasted from other similar
SoCs but forgot this one is different. Fix it.
Fixes: a085f877a882 ("clk: qcom: Move cxo/pxo/xo into dt files") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit commit eb1c8f4325d5 ("hwmon: (lm90) Convert to use new hwmon
registration API") the temp1_max_alarm and temp1_crit_alarm attributes are
mapped to the same alarm bit. Fix the typo.
Fixes: eb1c8f4325d5 ("hwmon: (lm90) Convert to use new hwmon registration API") Signed-off-by: Micehael Walle <michael@walle.cc> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix overflows seen when writing into fan speed limit attributes.
Also fix crash due to division by zero, seen when certain very
large values (such as 2147483648, or 0x80000000) are written
into fan speed limit attributes.
Fixes: 594fbe713bf60 ("Add support for GMT G762/G763 PWM fan controllers") Cc: Arnaud Ebalard <arno@natisbad.org> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix overflows seen when writing voltage and temperature limit attributes.
The value passed to DIV_ROUND_CLOSEST() needs to be clamped, and the
value parameter passed to nct7802_write_fan_min() is an unsigned long.
Also, writing values larger than 2700000 into a fan limit attribute results
in writing 0 into the chip's limit registers. The exact behavior when
writing this value is unspecified. For consistency, report a limit of 1350000 if the chip register reads 0. This may be wrong, and the chip
behavior should be verified with the actual chip, but it is better than
reporting a value of 0 (which, when written, results in writing a value
of 0x1fff into the chip register).
Fixes: 3434f3783580 ("hwmon: Driver for Nuvoton NCT7802Y") Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Converts the unsigned temperature values from the i2c read
to be sign extended as defined in the datasheet so that
negative temperatures are properly read.
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
$
After this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
alias: of:N*T*Carm,scpi-sensorsC*
alias: of:N*T*Carm,scpi-sensors
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Fixes: ea98b29a05e9c ("hwmon: Support sensors exported via ARM SCP interface") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All LED-setting functions in fujitsu-laptop are currently assigned to
the brightness_set callback, which is incorrect because they can sleep
(due to their use of call_fext_func(), which in turn issues ACPI calls)
and the documentation (in include/linux/leds.h) clearly states they must
not. Assign them to brightness_set_blocking instead and change them to
match the expected function prototype.
This change makes it possible to use Fujitsu-specific LEDs with "heavy"
triggers, like disk-activity or phy0rx.
Fixes: 3a407086090b ("fujitsu-laptop: Add BL power, LED control and radio state information") Fixes: 4f62568c1fcf ("fujitsu-laptop: Support radio LED") Fixes: d6b88f64b0d4 ("fujitsu-laptop: Add support for eco LED") Signed-off-by: Michał Kępień <kernel@kempniu.pl> Acked-by: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A typo (or mis-merge?) resulted in leaf 6 only being probed if
cpuid_level >= 7.
Fixes: 2ccd71f1b278 ("x86/cpufeature: Move some of the scattered feature bits to x86_capability") Signed-off-by: Andy Lutomirski <luto@kernel.org> Acked-by: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Link: http://lkml.kernel.org/r/6ea30c0e9daec21e488b54761881a6dfcf3e04d0.1481825597.git.luto@kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The slp_s0_residency_usec debugfs file currently uses
DEFINE_DEBUGFS_ATTRIBUTE(), but that macro cannot really be used to
define files outside of the debugfs code, as it has no reference to
the get/set functions if CONFIG_DEBUG_FS is not defined:
drivers/platform/x86/intel_pmc_core.c:80:12: error: ‘pmc_core_dev_state_get’ defined but not used [-Werror=unused-function]
This fixes the macro to always contain the reference, and instead rely
on the stubbed-out debugfs_create_file to not actually refer to
its arguments so the compiler can still drop the reference.
This works because the attribute definition is always 'static',
and the dead-code removal silently drops all static symbols
that are not used.
Fixes: c64688081490 ("debugfs: add support for self-protecting attribute file fops") Fixes: df2294fb6428 ("intel_pmc_core: Convert to DEFINE_DEBUGFS_ATTRIBUTE") Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[nicstange@gmail.com: Add dummy implementations of debugfs_attr_read() and
debugfs_attr_write() in order to protect against possibly broken dead
code elimination and to improve readability.
Correct CONFIG_DEBUGFS_FS -> CONFIG_DEBUG_FS typo in changelog.] Signed-off-by: Nicolai Stange <nicstange@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_ETRAX_AXISFLASHMAP is not configured, the flash rescue image
object file is empty. With recent versions of binutils, this results
in the following build error.
cris-linux-objcopy: error:
the input file 'arch/cris/boot/rescue/rescue.o' has no sections
This is seen, for example, when trying to build cris:allnoconfig
with recently generated toolchains.
Since it does not make sense to build a flash rescue image if there is
no flash, only build it if CONFIG_ETRAX_AXISFLASHMAP is enabled.
TPS65217 IRQ domain should be removed and initialised as NULL when the
module is unloaded for the next use. When tps65217.ko is loaded again,
it causes the page fault. This patch fixes the error below.
Fixes: 6556bdacf646 ("mfd: tps65217: Add support for IRQs") Signed-off-by: Milo Kim <woogyom.kim@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This partially reverts 'commit 2cdce425aa33
("ath10k: Fix broken NULL func data frame status for 10.4")'
Unfortunately this breaks sending NULL func and the existing
issue of obtaining proper tx status for NULL function will be
fixed. Also update the comments for feature flag added to be
useless and not working
Fixes: 2cdce425aa33 "ath10k: Fix broken NULL func data frame status for
10.4" Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NL80211_ATTR_MAC was used to set both the specific BSSID to be scanned
and the random MAC address to be used when privacy is enabled. When both
the features are enabled, both the BSSID and the local MAC address were
getting same value causing Probe Request frames to go with unintended
DA. Hence, this has been fixed by using a different NL80211_ATTR_BSSID
attribute to set the specific BSSID (which was the more recent addition
in cfg80211) for a scan.
Backwards compatibility with old userspace software is maintained to
some extent by allowing NL80211_ATTR_MAC to be used to set the specific
BSSID when scanning without enabling random MAC address use.
Scanning with random source MAC address was introduced by commit ad2b26abc157 ("cfg80211: allow drivers to support random MAC addresses
for scan") and the issue was introduced with the addition of the second
user for the same attribute in commit 818965d39177 ("cfg80211: Allow a
scan request for a specific BSSID").
Fixes: 818965d39177 ("cfg80211: Allow a scan request for a specific BSSID") Signed-off-by: Vamsi Krishna <vamsin@qti.qualcomm.com> Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On drivers setting the SUPPORTS_REORDERING_BUFFER hardware flag,
we crash when the peer sends an AddBA request while we already
have a session open on the seame TID; this is because on those
drivers, the tid_agg_rx is left NULL even though the session is
valid, and the agg_session_valid bit is set.
To fix this, store the dialog tokens outside the tid_agg_rx to
be able to compare them to the received AddBA request.
It's been unfixed since a while and no one is immediately working on
this. And we have the FIXME already. And now also a task in the DP
team's backlog.
Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@vger.kernel.org Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: https://lists.freedesktop.org/archives/intel-gfx/2016-July/101951.html Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Adjust comment per Ville's feedback.] Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161213195414.28923-1-daniel.vetter@ffwll.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 2dd85aeb5bc99e3763dd192cdb95ff405a102c8a) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently it's entirely possible to go through the link training step
without first determining the lane_count, which is silly since we end up
doing a bunch of aux transfers of size = 0, as highlighted by
WARN_ON(!msg->buffer != !msg->size), and can only ever result in a
'failed to update link training' message. This can be observed during
intel_dp_long_pulse where we can do the link training step, but before
we have had a chance to set the link params. To avoid this we add an
extra check for the lane_count in intel_dp_check_link_status, which
should prevent us from doing the link training step prematurely.
v2: add WARN_ON_ONCE and FIXME comment (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=97344 Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1476912593-10019-1-git-send-email-matthew.auld@intel.com Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0416e494ce7d ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.
Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.
Fixes: 0416e494ce7d ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") Cc: <stable@vger.kernel.org> Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com> Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For now this is just a cleanup patch, no functional
changes. We will be using the new function to fix a
bug introduced long ago by commit 0416e494ce7d
("usb: dwc3: ep0: correct cache sync issue in case
of ep0_bounced") and further worsened by commit c0bd5456a470 ("usb: dwc3: ep0: handle non maxpacket
aligned transfers > 512")
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Which is because we read a raw value for 1g as 64 which is
the nominal 1024 for 1g shifted 4 bits to the left by being
right-aligned rather than left aligned.
Since all other sensors are left aligned, add some code to
set the special DAS (data alignment setting) bit to 1 so that
the right value is now read like this:
The scaling was weird as well: we have a gain of 1000 for 1g
and 3000 for 6g. I don't even remember how I came up with the
old values but they are wrong.
Fixes: 3acddf74f807 ("iio: st-sensors: add support for lis3lv02d accelerometer") Cc: Lorenzo Bianconi <lorenzo.bianconi@st.com> Cc: Giuseppe Barba <giuseppe.barba@st.com> Cc: Denis Ciocca <denis.ciocca@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The oversampling ratio is controlled using the oversampling pins,
OS [2:0] with OS2 being the MSB control bit, and OS0 the LSB control
bit.
The gpio connected to the OS2 pin is not being set correctly, only OS0
and OS1 pins are being set. Fix the typo to allow proper control of the
oversampling pins.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com> Fixes: b9618c0 ("staging: IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4") Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The credentials handling was pushed to the write handlers
but error handling wasn't done properly.
Move write callbacks to completion queue to destroy them
and to notify a blocked writer about the failure
Fixes: 136698e535cd1 (mei: push credentials inside the irq write handler) Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: d49dc5e76fc9 (mei: bus: use mei_cldev_ prefix for the API functions) Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bind to the interface, but do not register any ports, after having
downloaded the firmware. The device will still disconnect and
re-enumerate, but this way we avoid an error messages from being logged
as part of the process:
io_ti: probe of 1-1.3:1.0 failed with error -5
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2 USB host ports are directly tied to the 2 USB hosts in the SoC.
The 2 host pairs were already enabled, but the USB PHY wasn't.
VBUS on the 2 ports are always on.
Enable the USB PHY.
Fixes: 04c85ecad32a ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus
board") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-beck.git / log