Laurent Pinchart [Wed, 31 Aug 2011 11:00:56 +0000 (13:00 +0200)]
fbdev: sh_mobile_lcdc: Update fix.line_length in .fb_set_par()
Instead of updating the fixed screen information line length manually
after calling fb_set_var() in sh_mobile_fb_reconfig(), update the field
in the .fb_set_par() operation handler.
Laurent Pinchart [Wed, 31 Aug 2011 11:00:52 +0000 (13:00 +0200)]
sh_mobile_meram: Reset ICBs at unregistration time
When ICBs are unregistered and later reused they need to be reset to
avoid data corruption. Set the WBF, WF and RF bits to make sure ICBs get
reset properly.
Bruno Prémont [Fri, 2 Sep 2011 17:24:03 +0000 (19:24 +0200)]
fb: sh-mobile: Fix deadlock risk between lock_fb_info() and console_lock()
Following on Herton's patch "fb: avoid possible deadlock caused by
fb_set_suspend" which moves lock_fb_info() out of fb_set_suspend()
to its callers, correct sh-mobile's locking around call to
fb_set_suspend() and the same sort of deaklocks with console_lock()
due to order of taking the lock.
console_lock() must be taken while fb_info is already locked and fb_info
must be locked while calling fb_set_suspend().
fb: avoid possible deadlock caused by fb_set_suspend
A lock ordering issue can cause deadlocks: in framebuffer/console code,
all needed struct fb_info locks are taken before acquire_console_sem(),
in places which need to take console semaphore.
But fb_set_suspend is always called with console semaphore held, and
inside it we call lock_fb_info which gets the fb_info lock, inverse
locking order of what the rest of the code does. This causes a real
deadlock issue, when we write to state fb sysfs attribute (which calls
fb_set_suspend) while a framebuffer is being unregistered by
remove_conflicting_framebuffers, as can be shown by following show
blocked state trace on a test program which loads i915 and runs another
forked processes writing to state attribute:
fb-test2 which reproduces above is available on kernel.org bug #26232.
To solve this issue, avoid calling lock_fb_info inside fb_set_suspend,
and move it out to where needed (callers of fb_set_suspend must call
lock_fb_info before if needed). So far, the only place which needs to
call lock_fb_info is store_fbstate, all other places which calls
fb_set_suspend are suspend/resume hooks that should not need the lock as
they should be run only when processes are already frozen in
suspend/resume.
Tomi Valkeinen [Thu, 25 Aug 2011 12:36:40 +0000 (15:36 +0300)]
fbdev: fix parsing of standard timings
The standard timings parses uses 1:1 dimensions when the ratio in the
EDID data is 0. However, for EDID 1.3 and later the dimensions are 16:10
when the ratio is 0.
Pass the version and revision numbers to get_std_timing() which can then
make the right decision about dimensions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Axel Lin [Thu, 1 Sep 2011 00:13:38 +0000 (08:13 +0800)]
video: nuc900fb: remove include of mach/clkdev.h
Since commit aa3831cf9d29cfeaebd8c2169378b74111364487
"ARM: Consolidate the clkdev header files",
the header file arch/arm/mach-nuc93x/include/mach/clkdev.h is removed.
This patch fixes below build error:
drivers/video/nuc900fb.c:42:25: error: mach/clkdev.h: No such file or directory
make[2]: *** [drivers/video/nuc900fb.o] Error 1
make[1]: *** [drivers/video] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Axel Lin [Thu, 1 Sep 2011 00:11:59 +0000 (08:11 +0800)]
video: mxsfb: add missing include of linux/module.h
Include linux/module.h to fix below build error:
from drivers/video/mxsfb.c:42:
arch/arm/mach-mxs/include/mach/memory.h:22:1: warning: this is the location of the previous definition
drivers/video/mxsfb.c:574: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/video/mxsfb.c:893: warning: data definition has no type or storage class
drivers/video/mxsfb.c:893: warning: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/video/mxsfb.c:893: warning: parameter names (without types) in function declaration
drivers/video/mxsfb.c:917: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:917: warning: data definition has no type or storage class
drivers/video/mxsfb.c:917: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/video/mxsfb.c:917: warning: function declaration isn't a prototype
drivers/video/mxsfb.c:918: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:918: warning: data definition has no type or storage class
drivers/video/mxsfb.c:918: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/video/mxsfb.c:918: warning: function declaration isn't a prototype
drivers/video/mxsfb.c:919: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:919: warning: data definition has no type or storage class
drivers/video/mxsfb.c:919: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/video/mxsfb.c:919: warning: function declaration isn't a prototype
make[2]: *** [drivers/video/mxsfb.o] Error 1
make[1]: *** [drivers/video] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Jingoo Han [Mon, 22 Aug 2011 03:16:04 +0000 (12:16 +0900)]
video: s3c-fb: Add support EXYNOS4 FIMD
This patch adds struct s3c_fb_driverdata s3c_fb_data_exynos4 for EXYNOS4
and adds lcd clock gating support.
FIMD driver needs two clocks for FIMD IP and LCD pixel clock. Previously,
both clocks are provided by using bus clock such as HCLK. However, EXYNOS4
can not select HCLK for LCD pixel clock because the EXYNOS4 FIMD IP does not
have the CLKSEL bit of VIDCON0. So, FIMD driver should provide the lcd clock
using SCLK_FIMD as LCD pixel clock for EXYNOS4.
The driver selects enabling lcd clock according to has_clksel which means
the CLKSEL bit of VIDCON0. If there is has_clksel, the driver will not
enable the lcd clock using SCLK_FIMD because bus clock using HCLK is used
a LCD pixel clock.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Bernie Thompson [Sun, 21 Aug 2011 20:35:38 +0000 (13:35 -0700)]
udlfb: Enable fb_defio by default
Enables page fault based detection of mmap writes to the framebuffer,
which allows standard fbdev apps (like the generic fbdev xorg driver)
to work on DisplayLink devices.
Not all bugs are shaken out of the fb_defio path of udlfb, but it's
tantalizingly close, so this seems a good time to enable by default.
Alternatively, option can be disabled when running with an xorg driver
that can more directly communicate damaged regions of the framebuffer
via IOCTL. This is a simpler, higher perf option, when available.
Stuart Hopkins [Sun, 21 Aug 2011 20:34:17 +0000 (13:34 -0700)]
udlfb: Add module option to do without shadow framebuffer
By default, udlfb allocates a 2nd buffer to shadow what's across
the bus on the USB device. It can operate without this shadow,
but then it cannot tell which pixels have changed, and must send all.
Saves host memory, but worsens the USB 2.0 bus bottleneck.
This option allows users in very low memory situations (e.g.
bifferboard) to optionally turn off this shadow framebuffer.
udlfb: fix issues found with Sparse static analysis
Add __user casting, a missing copy_from_user, and proper boolean
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Signed-off-by: Bernie Thompson <bernie@plugable.com> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Andrew Kephart [Sun, 21 Aug 2011 20:34:13 +0000 (13:34 -0700)]
udlfb: Search config descriptor if not at device level
For at least one DisplayLink device, the vendor-specific information can
be found in the config descriptor instead of as a separate, device-level
descriptor. This patch searches the current interface (of the current
config descriptor) for the DL vendor-specific descriptor.
Bernie Thompson [Sun, 21 Aug 2011 20:34:11 +0000 (13:34 -0700)]
udlfb: add more comprehensive support for DPMS FB_BLANK_* modes
Fixes earlier problems where monitor would not return from blank
Test with any DisplayLink-based USB 2.0 graphics adapter
sudo nano /sys/class/graphics/fb?/blank
and write out single digit FB_BLANK_* code from include/linux/fb.h
Supports on (0), blank (1), suspend (2,3), powerdown (4)
Linus Torvalds [Mon, 22 Aug 2011 18:25:44 +0000 (11:25 -0700)]
Merge branch 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/tracing: Fix tracing config option properly
xen: Do not enable PV IPIs when vector callback not present
xen/x86: replace order-based range checking of M2P table by linear one
xen: xen-selfballoon.c needs more header files
This change replaced the SMP operations with event based handlers without
taking into account that this only works when the hypervisor supports
callback vectors. This causes unexplainable hangs early on boot for
HVM guests with more than one CPU.
BugLink: http://bugs.launchpad.net/bugs/791850 CC: stable@kernel.org Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Tested-and-Reported-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Josef Bacik [Sat, 20 Aug 2011 12:29:51 +0000 (08:29 -0400)]
Btrfs: fix 64 bit divide problem
This fixes a regression introduced by commit cdcb725c05fe ("Btrfs: check
if there is enough space for balancing smarter"). We can't do 64-bit
divides on 32-bit architectures.
In cases where we need to divide/multiply by 2 we should just left/right
shift respectively, and in cases where theres N number of devices use
do_div. Also make the counters u64 to match up with rw_devices.
Thanks,
Linus Torvalds [Sun, 21 Aug 2011 13:59:41 +0000 (06:59 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: flush any pending end_io requests before DIO reads w/dioread_nolock
ext4: fix nomblk_io_submit option so it correctly converts uninit blocks
ext4: Resolve the hang of direct i/o read in handling EXT4_IO_END_UNWRITTEN.
ext4: call ext4_ioend_wait and ext4_flush_completed_IO in ext4_evict_inode
ext4: Fix ext4_should_writeback_data() for no-journal mode
Linus Torvalds [Sun, 21 Aug 2011 13:59:02 +0000 (06:59 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/aoa/fabrics/layout.c: remove unneeded kfree
ALSA: hda - Fix error check from snd_hda_get_conn_index() in patch_cirrus.c
ALSA: hda - Don't spew too many ELD errors
ALSA: usb-audio - Fix missing mixer dB information
ALSA: hda - Add "PCM" volume to vmaster slave list
ALSA: hda - Fix duplicated capture-volume creation for ALC268 models
ALSA: ac97: Add HP Compaq dc5100 SFF(PT003AW) to Headphone Jack Sense whitelist
ALSA: snd_usb_caiaq: track submitted output urbs
Randy Dunlap [Sat, 20 Aug 2011 18:49:43 +0000 (11:49 -0700)]
pci: fix new kernel-doc warning in pci.c
Fix new kernel-doc warning in pci.c:
Warning(drivers/pci/pci.c:3259): No description found for parameter 'mps'
Warning(drivers/pci/pci.c:3259): Excess function parameter 'rq' description in 'pcie_set_mps'
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Sat, 20 Aug 2011 07:14:45 +0000 (09:14 +0200)]
ALSA: hda - Don't spew too many ELD errors
Currently HD-audio driver shows the all error ELD byte as an error
in the kernel message. This is annoying when the video driver doesn't
set the correct ELD from the beginning. e.g. radeon sends a zero-byte
data, but we still check ELD with the fixed 128 byte as a workaround
for some broken devices, it spews 128-times errors.
For avoiding this, the driver aborts reading when the first byte is
invalid. In such a case, the whole data is certainly invalid.
Linus Torvalds [Sat, 20 Aug 2011 06:07:08 +0000 (23:07 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Jiaying Zhang [Fri, 19 Aug 2011 23:13:32 +0000 (19:13 -0400)]
ext4: flush any pending end_io requests before DIO reads w/dioread_nolock
There is a race between ext4 buffer write and direct_IO read with
dioread_nolock mount option enabled. The problem is that we clear
PageWriteback flag during end_io time but will do
uninitialized-to-initialized extent conversion later with dioread_nolock.
If an O_direct read request comes in during this period, ext4 will return
zero instead of the recently written data.
This patch checks whether there are any pending uninitialized-to-initialized
extent conversion requests before doing O_direct read to close the race.
Note that this is just a bandaid fix. The fundamental issue is that we
clear PageWriteback flag before we really complete an IO, which is
problem-prone. To fix the fundamental issue, we may need to implement an
extent tree cache that we can use to look up pending to-be-converted extents.
Jesse Barnes [Fri, 12 Aug 2011 22:28:32 +0000 (15:28 -0700)]
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command. However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL. Since we're not doing that yet, go
back to the old default so things work.
v2: don't forget to actually *clear* the new bit
Reviewed-by: Eric Anholt <eric@anholt.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Linus Torvalds [Fri, 19 Aug 2011 17:47:07 +0000 (10:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block: (23 commits)
Revert "cfq: Remove special treatment for metadata rqs."
block: fix flush machinery for stacking drivers with differring flush flags
block: improve rq_affinity placement
blktrace: add FLUSH/FUA support
Move some REQ flags to the common bio/request area
allow blk_flush_policy to return REQ_FSEQ_DATA independent of *FLUSH
xen/blkback: Make description more obvious.
cfq-iosched: Add documentation about idling
block: Make rq_affinity = 1 work as expected
block: swim3: fix unterminated of_device_id table
block/genhd.c: remove useless cast in diskstats_show()
drivers/cdrom/cdrom.c: relax check on dvd manufacturer value
drivers/block/drbd/drbd_nl.c: use bitmap_parse instead of __bitmap_parse
bsg-lib: add module.h include
cfq-iosched: Reduce linked group count upon group destruction
blk-throttle: correctly determine sync bio
loop: fix deadlock when sysfs and LOOP_CLR_FD race against each other
loop: add BLK_DEV_LOOP_MIN_COUNT=%i to allow distros 0 pre-allocated loop devices
loop: add management interface for on-demand device allocation
loop: replace linked list of allocated devices with an idr index
...
Linus Torvalds [Fri, 19 Aug 2011 17:02:37 +0000 (10:02 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: OF: Don't crash when bridge parent is NULL.
PCI: export pcie_bus_configure_settings symbol
PCI: code and comments cleanup
PCI: make cardbus-bridge resources optional
PCI: make SRIOV resources optional
PCI : ability to relocate assigned pci-resources
PCI: honor child buses add_size in hot plug configuration
PCI: Set PCI-E Max Payload Size on fabric
Laurent Pinchart [Wed, 25 May 2011 09:34:52 +0000 (11:34 +0200)]
savagefb: use display information in info not in var for panning
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it. Also use the
aligned fix.line_length and not the (possible) unaligned xres_virtual.
Laurent Pinchart [Wed, 25 May 2011 09:34:52 +0000 (11:34 +0200)]
mx3fb: use display information in info not in var for panning
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it. Also use the
aligned fix.line_length and not the (possible) unaligned xres_virtual.
Laurent Pinchart [Wed, 25 May 2011 09:34:52 +0000 (11:34 +0200)]
radeonfb: use display information in info not in var for panning
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it. Also use the
aligned fix.line_length and not the (possible) unaligned xres_virtual.
Jens Axboe [Fri, 19 Aug 2011 06:34:48 +0000 (08:34 +0200)]
Revert "cfq: Remove special treatment for metadata rqs."
We have a kernel build regression since 3.1-rc1, which is about 10%
regression. The kernel source is in an ext3 filesystem.
Alex Shi bisect it to commit:
commit a07405b7802691d29ab3b23bdc76ee6d006aad0b
Author: Justin TerAvest <teravest@google.com>
Date: Sun Jul 10 22:09:19 2011 +0200
cfq: Remove special treatment for metadata rqs.
Apparently this is caused by lack metadata preemption, where ext3/ext4
do use READ_META. I didn't see a way to fix the issue, so suggest
reverting the patch.
The drivers/video/sh_mobile_meram.h header contains unused definitions
and declarations. Move the only used macro to sh_mobile_meram.c, and
remove the header.
fbdev: sh_mobile_meram: Replace hardcoded register values with macros
Instead of hardcoding register values through the driver, define macros
for individual register bits using the register name and the bit name,
and use the macros.
fbdev: sh_mobile_lcdc: Restart LCDC in runtime PM resume handler
Instead of restoring registers blindly, restart the LCDC by going
through the startup sequence when resuming from runtime PM suspend. All
registers are now correctly initialized in the right order.
As a side effect, this also gets rid fo a possible panning restore issue
caused by always saving the frame buffer base address registers from set
A instead of the currently active set.
fbdev: sh_mobile_lcdc: Store the frame buffer base address when panning
When the frame buffer base address is changed by a panning operation,
store it in the channel structure. It will be reused when runtime PM
code will use __sh_mobile_lcdc_start().
fbdev: sh_mobile_lcdc: Compute clock pattern using divider denominator
The clock divider pattern is computed based on the dot clock register
value which stores the divider denumerator. However, when using a 1:1
divider ratio, the register is programmed with a value that must not be
interpreted as a denominator. This results in a shift left operation
with a value of 32, which produces undefined behaviour.
Compute the clock pattern using the divider denominator, not the dot
clock register value.
The LDINTR register caries both interrupt enable and interrupt status
bits. When setting or clearing interrupt enable bits, write all status
bits to 1 to avoid acknowledging interrupts by mistake.
When acknowledging interrupts, write 1 to all non-triggered interrupt
bits to avoid losing interrupts.
fbdev: sh_mobile_lcdc: Replace hardcoded register values with macros
Instead of hardcoding register values through the driver, define macros
for individual register bits using the register name and the bit name,
and use the macros.
Takashi Iwai [Fri, 19 Aug 2011 05:55:10 +0000 (07:55 +0200)]
ALSA: usb-audio - Fix missing mixer dB information
The recent fix for testing dB range at the mixer creation time seems
to cause regressions in some devices. In such devices, reading the dB
info at probing time gives an error, thus both dBmin and dBmax are still
zero, and TLV flag isn't set although the later read of dB info succeeds.
This patch adds a workaround for such a case by assuming that the later
read will succeed. In future, a similar test should be performed in a
case where a wrong dB range is seen even in the later read.
Linus Torvalds [Fri, 19 Aug 2011 05:47:13 +0000 (22:47 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Return NFS4ERR_BADSESSION to callbacks during session resets
NFSv4.1: Fix the callback 'highest_used_slotid' behaviour
pnfs-obj: Fix the comp_index != 0 case
pnfs-obj: Bug when we are running out of bio
nfs: add missing prefetch.h include
Ian Campbell [Wed, 17 Aug 2011 22:14:57 +0000 (22:14 +0000)]
sparc: fix array bounds error setting up PCIC NMI trap
CC arch/sparc/kernel/pcic.o
arch/sparc/kernel/pcic.c: In function 'pcic_probe':
arch/sparc/kernel/pcic.c:359:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:359:8: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:360:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:360:8: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:361:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:361:8: error: array subscript is above array bounds [-Werror=array-bounds]
cc1: all warnings being treated as errors
I'm not particularly familiar with sparc but t_nmi (defined in head_32.S via
the TRAP_ENTRY macro) and pcic_nmi_trap_patch (defined in entry.S) both appear
to be 4 instructions long and I presume from the usage that instructions are
int sized.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Mon, 8 Aug 2011 11:17:57 +0000 (13:17 +0200)]
drivers/ata/sata_dwc_460ex.c: add missing kfree
Currently, error handling code in this function calls the function
sata_dwc_port_stop, but this function has essentially no effect if hsdevp
has not been stored in ap, which is the case throughout this function. The
only effect is to print a debugging message including ap->print_id.
The code is rewritten to not call sata_dwc_port_stop, but instead to jump
to a local label that prints the original error message and the print_id
information. In the case where hsdevp has been already allocated (but not
yet stored in ap), this value is freed as well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add basic support for pata on iMX. It has been tested only on imx51.
SDMA support will probably be added later so this version supports only
PIO.
v2:
- enable only when needed IORDY
- use dev_get_drvdata
v3:
- add missing clk_put() calls
- use platform_get_irq()
- fix resume code to avoid disabling IORDY on resume
v4:
- Remove EXPERIMENTAL and switch to depends on ARCH_MXC
- Use devm_kzalloc()
- make clock a must-have
- Use only 1 ioremap
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 4 Aug 2011 09:15:07 +0000 (11:15 +0200)]
pata_via: disable ATAPI DMA on AVERATEC 3200
On AVERATEC 3200, pata_via causes memory corruption with ATAPI DMA,
which often leads to random kernel oops. The cause of the problem is
not well understood yet and only small subset of machines using the
controller seem affected. Blacklist ATAPI DMA on the machine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=11426 Reported-and-tested-by: Jim Bray <jimsantelmo@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff Garzik [Fri, 19 Aug 2011 03:52:36 +0000 (23:52 -0400)]
[libata] sata_sil: fix used-uninit warning
Init 'serror' to silence the following warning:
drivers/ata/sata_sil.c: In function ‘sil_interrupt’:
drivers/ata/sata_sil.c:453:14: warning: ‘serror’ may be used uninitialized in
this function [-Wuninitialized]
This is not a 'can never happen' but is nonetheless extremely unlikely.
The easiest and cleanest warning fix is simply to init the var,
rather than worry about marking the var uninit-ok.
Linus Torvalds [Thu, 18 Aug 2011 21:20:00 +0000 (14:20 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: set i_size properly when fallocating and we already
btrfs: unlock on error in btrfs_file_llseek()
btrfs: btrfs_permission's RO check shouldn't apply to device nodes
Btrfs: truncate pages from clone ioctl target range
Btrfs: fix uninitialized sync_pending
Btrfs: fix wrong free space information
btrfs: memory leak in btrfs_add_inode_defrag()
Btrfs: use plain page_address() in header fields setget functions
Btrfs: forced readonly when btrfs_drop_snapshot() fails
Btrfs: check if there is enough space for balancing smarter
Btrfs: fix a bug of balance on full multi-disk partitions
Btrfs: fix an oops of log replay
Btrfs: detect wether a device supports discard
Btrfs: force unplugs when switching from high to regular priority bios
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
update cifs version to 1.75
[CIFS] possible memory corruption on mount
cifs: demote cERROR in build_path_from_dentry to cFYI
projects / mv-sheeva.git / log