ath10k: remove shadow copy of CE descriptors for source ring
For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: remove send completion validation in diag read/write
CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: use local memory instead of shadow descriptor in ce_send
Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Maharaja [Wed, 21 Oct 2015 08:49:18 +0000 (11:49 +0300)]
ath10k: enable adaptive CCA
European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.
Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.
The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com> Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rafał Miłecki [Thu, 15 Oct 2015 05:23:25 +0000 (07:23 +0200)]
ssb: pick PCMCIA host code support from b43 driver
ssb bus can be found on various "host" devices like PCI/PCMCIA/SDIO.
Every ssb bus contains cores AKA devices.
The main idea is to have ssb driver scan/initialize bus and register
ready-to-use cores. This way ssb drivers can operate on a single core
mostly ignoring underlaying details.
For some reason PCMCIA support was split between ssb and b43. We got
PCMCIA host device probing in b43, then bus scanning in ssb and then
wireless core probing back in b43. The truth is it's very unlikely we
will ever see PCMCIA ssb device with no 802.11 core but I still don't
see any advantage of the current architecture.
With proposed change we get the same functionality with a simpler
architecture, less Kconfig symbols, one killed EXPORT and hopefully
cleaner b43. Since b43 supports both: ssb & bcma I prefer to keep ssb
specific code in ssb driver.
This mostly moves code from b43's pcmcia.c to bridge_pcmcia_80211.c. We
already use similar solution with b43_pci_bridge.c. I didn't use "b43"
in name of this new file as in theory any driver can operate on wireless
core.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marty Faltesek [Mon, 26 Oct 2015 05:54:01 +0000 (22:54 -0700)]
mwifiex: toggle carrier state in start_ap/stop_ap.
In uap mode the carrier is not enabled until after the first STA joins.
The carrier triggers the bridge to start its state machine, and if STP
is enabled, it takes 4 seconds as it transitions from disabled to
forwarding. During this time the bridge drops all traffic, and the EAPOL
handshake times out after 3 seconds, preventing stations from joining.
Follow the logic used in mac80211 and start the carrier in start_ap
and disable it in stop_ap. This has a nice benefit of allowing the
first station connection time to be reduced by up to 75% when STP is
in use.
Signed-off-by: Martin Faltesek <mfaltesek@google.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bob Copeland [Sat, 24 Oct 2015 17:42:15 +0000 (13:42 -0400)]
wcn36xx: introduce per-channel ring buffer locks
wcn36xx implements a ring buffer for transmitted frames for each
(high and low priority) DMA channel. The ring buffers are lockless:
new frames are inserted at the head of the queue, while finished
packets are reaped from the tail.
Unfortunately, the list manipulations are missing any kind of barriers
so are susceptible to various races: for example, a TX completion
handler might read an updated desc->ctrl before the head has actually
advanced, and then null out the ctl->skb pointer while it is still
being used in the TX path.
Simplify things here by adding a spin lock when traversing the ring.
This change increased stability for me without adding any noticeable
overhead on my platform (xperia z).
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zefir Kurtisi [Tue, 20 Oct 2015 12:19:26 +0000 (14:19 +0200)]
ath9k: fix phyerror codes
Some of the ath9k_phyerr enums were wrong from the
beginning (and even before). Most of the time the
codes were used for counters to be displayed over
debugfs, which made this a non-functional issue.
Some (e.g. ATH9K_PHYERR_FALSE_RADAR_EXT) are used
for radar detection and require the correct code
to work as intended.
John Linville [Mon, 19 Oct 2015 15:15:00 +0000 (11:15 -0400)]
orinoco_usb: return error in ezusb_probe when alloc_orinocodev fails
The current code exits after alloc_orinocodev, but fails to change the
return value to something that indicates the failure. This patch
changes the return value to -ENOMEM.
Ondrej Zary [Fri, 16 Oct 2015 19:04:13 +0000 (21:04 +0200)]
airo: Track APList_rid in struct airo_info
Instead of dynamically allocating APList, make it a member of struct
airo_info to always track state of APList_rid.
This simplifies suspend/resume and allows removal of readAPListRid.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Wed, 28 Oct 2015 18:48:26 +0000 (20:48 +0200)]
Merge tag 'iwlwifi-next-for-kalle-2015-10-25' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* bug fix for TDLS
* fixes and cleanups in scan
* support of several scan plans
* improvements in FTM
* fixes in FW API
* improvements in the failure paths when the bus is dead
* other various small things here and there
yankejian [Tue, 27 Oct 2015 11:16:34 +0000 (19:16 +0800)]
net: hisilicon: updates HNS config and documents
updates the bindings documents and dtsi file according to the review
comments[https://lkml.org/lkml/2015/9/21/670] from Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: yankejian <yankejian@huawei.com> Signed-off-by: huangdaode <huangdaode@hisilicon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li Peng [Tue, 27 Oct 2015 09:17:40 +0000 (17:17 +0800)]
net: hns: fixes the bug tested XGE by ethtool -p
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com> Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by: yankejian <yankejian@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:56:56 +0000 (19:56 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2015-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tycho Andersen [Tue, 27 Oct 2015 00:23:59 +0000 (09:23 +0900)]
seccomp, ptrace: add support for dumping seccomp filters
This patch adds support for dumping a process' (classic BPF) seccomp
filters via ptrace.
PTRACE_SECCOMP_GET_FILTER allows the tracer to dump the user's classic BPF
seccomp filters. addr should be an integer which represents the ith seccomp
filter (0 is the most recently installed filter). data should be a struct
sock_filter * with enough room for the ith filter, or NULL, in which case
the filter is not saved. The return value for this command is the number of
BPF instructions the program represents, or negative in the case of errors.
Command specific errors are ENOENT: which indicates that there is no ith
filter in this seccomp tree, and EMEDIUMTYPE, which indicates that the ith
filter was not installed as a classic BPF filter.
A caveat with this approach is that there is no way to get explicitly at
the heirarchy of seccomp filters, and users need to memcmp() filters to
decide which are inherited. This means that a task which installs two of
the same filter can potentially confuse users of this interface.
v2: * make save_orig const
* check that the orig_prog exists (not necessary right now, but when
grows eBPF support it will be)
* s/n/filter_off and make it an unsigned long to match ptrace
* count "down" the tree instead of "up" when passing a filter offset
v3: * don't take the current task's lock for inspecting its seccomp mode
* use a 0x42** constant for the ptrace command value
v4: * don't copy to userspace while holding spinlocks
v5: * add another condition to WARN_ON
v6: * rebase on net-next
Signed-off-by: Tycho Andersen <tycho.andersen@canonical.com> Acked-by: Kees Cook <keescook@chromium.org> CC: Will Drewry <wad@chromium.org> Reviewed-by: Oleg Nesterov <oleg@redhat.com> CC: Andy Lutomirski <luto@amacapital.net> CC: Pavel Emelyanov <xemul@parallels.com> CC: Serge E. Hallyn <serge.hallyn@ubuntu.com> CC: Alexei Starovoitov <ast@kernel.org> CC: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:53:04 +0000 (19:53 -0700)]
Merge branch 'mpls-multipath-improvements'
Robert Shearman says:
====================
mpls: mulipath improvements
Two improvements to the recently added mpls multipath support. The
first is a fix for missing initialisation the nexthop address length
for the v4 and v6 explicit null label routes, and the second is to
reduce the amount of memory used by mpls routes by changing the way
the via addresses are stored.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Tue, 27 Oct 2015 00:37:36 +0000 (00:37 +0000)]
mpls: reduce memory usage of routes
Nexthops for MPLS routes have a via address field sized for the
largest via address that is expected, which is 32 bytes. This means
that in the most common case of having ipv4 via addresses, 28 bytes of
memory more than required are used per nexthop. In the other common
case of an ipv6 nexthop then 16 bytes more than required are
used. With large numbers of MPLS routes this extra memory usage could
start to become significant.
To avoid allocating memory for a maximum length via address when not
all of it is required and to allow for ease of iterating over
nexthops, then the via addresses are changed to be stored in the same
memory block as the route and nexthops, but in an array after the end
of the array of nexthops. New accessors are provided to retrieve a
pointer to the via address.
To allow for O(1) access without having to store a pointer or offset
per nh, the via address for each nexthop is sized according to the
maximum via address for any nexthop in the route, which is stored in a
new route field, rt_max_alen, but this is in an existing hole in
struct mpls_route so it doesn't increase the size of the
structure. Each via address is ensured to be aligned to VIA_ALEN_ALIGN
to account for architectures that don't allow unaligned accesses.
Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Tue, 27 Oct 2015 00:37:35 +0000 (00:37 +0000)]
mpls: fix forwarding using v4/v6 explicit null
Fill in the via address length for the predefined IPv4 and IPv6
explicit-null label routes.
Fixes: f8efb73c97e2 ("mpls: multipath route support") Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Mon, 26 Oct 2015 14:23:42 +0000 (14:23 +0000)]
sfc: replace spinlocks with bit ops for busy poll locking
This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netstamp_needed is toggled for all socket families if they request
timestamping. But some protocols don't need the lower-layer timestamping
code at all. This patch starts disabling it for af-unix.
E.g. systemd enables timestamping during boot-up on the journald af-unix
sockets, thus causing the system to globally enable timestamping in the
lower networking stack. Still, it is very probable that timestamping
gets activated, by e.g. dhclient or various NTP implementations.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:35:01 +0000 (19:35 -0700)]
Merge branch 'qed-driver'
Ariel Elior says:
====================
Add new drivers: qed & qede
This series implements the driver set for Qlogic's new QL4xxx series.
These are 10/20/25/40/50/100 Gig capable converged nics, supporting
ethernet (obviously), iscsi, fcoe, roce and iwarp protocols.
The overall driver design includes a common module ('qed') and protocol
specific dependent modules for ethernet ('qede'), fcoe ('qedf'),
iscsi ('qedi') and roce ('qedr').
The common module contains all of the common logic, e.g. initialization,
cleanup, infrastructure for interrupt handling, link management, slowpath
etc. as well as protocol agnostic features, and supplying an abstraction
layer for other modules.
The protocol specific modules can be compiled and operated independently
of each other, with the exception of the rdma modules which are dependent
on the ethernet module, in accordance with the kernel rdma stack design.
This series only adds the core and ethernet modules, with basic L2
capabilities. Future series will add the rest of the modules and enhance
the L2 functionality.
Ths patch series is constructed of the following patches:
qed: Add module with basic common support
qed: Add basic L2 interface
qede: Add basic Network driver
qed: Add slowpath L2 support
qede: Add basic network device support
qede: Add classification configuration
qed: Add link support
qede: Add support for link
qed: Add statistics support
qede: Add basic ethtool support
This project is a team effort, thanks go to Yuval Mintz, Dmitry Kravkov,
Michal Kalderon, Tomer Tayar, Manish Chopra, Sudarsana Kalluru,
Rajesh Borundia, Sony Chacko, Artum Zolotushko, Harish Patil, Rasesh Mody,
Sergey Ukhterov and Elad Manela, as well as former team members,
Eilon Greenstein and Shmulik Ravid.
Changes from previos version:
-----------------------------
From Version 7:
- Various small fixes according to Dave's suggestions; Largest change
[code-wise] - don't use tabs for indenting function arguments.
From Version 6:
- Reduced the number of arguments for functions with exceptionally
high number of parameters.
From Version 5:
- Style change and fixes [mostly in 1, 4 and 7].
Thanks go to Francois Romieu, a mere mortal. ;-)
From Version 4:
- Drop dependency for x86_64.
From Version 3:
- Limit support of initial submission to x86_64.
- Fix endian problems appearing via sparse [although no BE support yet].
- Fix small issues suggested by the kbuild test robot.
From Version 2:
- Removed U64_{HI,LO}; Using {upper,lower}_32_bits instead.
- Use regular napi weight definition.
- [We still use the __le variants for variables, since we didn't get
a reply regarding the change into non-user API types].
From Version 1:
- Removed private license file; Instead revised comments at source headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 26 Oct 2015 09:02:33 +0000 (11:02 +0200)]
qed: Add statistics support
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:31 +0000 (11:02 +0200)]
qed: Add link support
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:29 +0000 (11:02 +0200)]
qede: Add basic network device support
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 26 Oct 2015 09:02:28 +0000 (11:02 +0200)]
qed: Add slowpath L2 support
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:27 +0000 (11:02 +0200)]
qede: Add basic Network driver
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:26 +0000 (11:02 +0200)]
qed: Add basic L2 interface
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:25 +0000 (11:02 +0200)]
qed: Add module with basic common support
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adding IPv6 for the TSO helper API is trivial:
* Don't play with the id (which doesn't exist in IPv6)
* Correctly update the payload_len (don't include the
length of the IP header itself)
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 27 Oct 2015 05:16:02 +0000 (22:16 -0700)]
Merge tag 'arcnet-for-4.4-rc1' of git://git.pengutronix.de/git/mgr/linux
Michael Grzeschik says:
====================
This series includes code simplifaction. The main changes are the correct
xceiver handling (enable/disable) of the com20020 cards. The driver now handles
link status change detection. The EAE PCI-ARCNET cards now make use of the
rotary encoded subdevice indexing and got support for led triggers on transmit
and reconnection events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
exported perf symbols are GPL only, mark eBPF helper functions
used in tracing as GPL only as well.
Suggested-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix safety checks for bpf_perf_event_read():
- only non-inherited events can be added to perf_event_array map
(do this check statically at map insertion time)
- dynamically check that event is local and !pmu->count
Otherwise buggy bpf program can cause kernel splat.
Also fix error path after perf_event_attrs()
and remove redundant 'extern'.
Fixes: 35578d798400 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Tested-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 23 Oct 2015 19:11:08 +0000 (12:11 -0700)]
net: dsa: bcm_sf2: Unhardcode port numbers
While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.
Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 23 Oct 2015 18:38:07 +0000 (11:38 -0700)]
net: dsa: bcm_sf2: Implement FDB operations
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8xxxu.c:5786:32: warning: ‘rtl8192cu_fops’ defined but not used [-Wunused-variable]
Fix it by adding temporary ifdefs around the static functions.
Fixes: 033695bdf6d7 ("rtl8xxxu: move devices supported by rtlwifi under UNTESTED config") Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The arcnet device has no interrupt to detect if the link has changed
from disconnected to connected. This patch adds an timer to toggle the
link detection. The timer will get retriggered as long as the
reconnection interrupts accure. If the recon interrupts hold off
for >1s we define the connection stable again.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has special leds on the the main io pci resource
bar. This patch adds support to trigger the conflict and data leds with
the packages.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has a special rotary encoder
to configure the address of every card individually.
We take this information for the initial setup of
the cards dev_id.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
arcnet: com20020: add enable and disable device on open/close
This patch changes the driver to properly work with the linux netif
interface. The controller gets enabled on open and disabled on close.
Therefor it removes every bogus start of the xceiver. It only gets
enabled on com20020_open and disabled on com20020_close.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Michael Chan [Mon, 26 Oct 2015 02:27:57 +0000 (22:27 -0400)]
bnxt_en: Fix compile warnings when CONFIG_INET is not set.
bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Ringle [Thu, 22 Oct 2015 19:09:04 +0000 (15:09 -0400)]
net: encx24j600: Fix mask to update LED configuration
This fixes the mask used to update the LED configuration so that it clears
the necessary bits as well as setting the bits according to the mask.
Also reverse the LED configuration to show the Link state + collisions in
LEDA and the Link state + TX/RX events in LEDB.
Signed-off-by: Jon Ringle <jringle@gridpoint.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 26 Oct 2015 01:20:41 +0000 (18:20 -0700)]
Merge branch 'mvneta-ethtool-stats'
Russell King says:
====================
mvneta ethtool statistics
Sorry for v3 - I forgot to update the commit message on patch 1 as
requested by Marcin.
This short series adds ethtool statistics reporting to mvneta. Having
discussed with Andrew on IRC, we decided I'd pick up his patch into my
series.
My change for patch 1 compared to the previous RFC splits out the
reading of the statistics from the hardware into a separate function,
in order to facilitate work going on elsewhere to arrange for the
statistics to be preserved across a suspend/resume cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 22 Oct 2015 17:37:36 +0000 (18:37 +0100)]
net: mvneta: Fix clearing of MIB statistics
The existing function to clear the MIB statatistics was using the
wrong address for the registers. Also, the counters would of been
cleared when the interface was brought up, not during the
probe. Fix both of these.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 23 Oct 2015 17:59:16 +0000 (10:59 -0700)]
af_unix: do not report POLLOUT on listeners
poll(POLLOUT) on a listener should not report fd is ready for
a write().
This would break some applications using poll() and pfd.events = -1,
as they would not block in poll()
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Alan Burlison <Alan.Burlison@oracle.com> Tested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wu Fengguang [Sat, 24 Oct 2015 14:56:01 +0000 (22:56 +0800)]
tipc: link_is_bc_sndlink() can be static
TO: "David S. Miller" <davem@davemloft.net> CC: netdev@vger.kernel.org CC: Jon Maloy <jon.maloy@ericsson.com> CC: Ying Xue <ying.xue@windriver.com> CC: tipc-discussion@lists.sourceforge.net CC: linux-kernel@vger.kernel.org Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi: nvm: free old section data when reading nvm file
When reading external NVM file, if a section exists both in OTP
and in the external file, the memory that was allocated at OTP
reading is not freed.
This is possible only on systems that have an external NVM
file which is typically the case on embedded systems.
Arik Nemtsov [Mon, 12 Oct 2015 11:47:11 +0000 (14:47 +0300)]
iwlwifi: mvm: disable TDLS ac queues correctly
The iwl_mvm_disable_queue function requires the TID to be set to
IWL_MAX_TID_COUNT when disabling an AC queue. Call it correctly for TDLS
scenarios.
Fixes: 4ecafae9e568 ("iwlwifi: mvm: support using multiple ACs on single HW queue") Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: mvm: Implement per vif frame registration API
Implement config_iface_filter() driver op. Currently support only
probe request registration for p2p client vifs, by setting
MAC_FILTER_IN_PROBE_REQUEST flag in MAC_CONTEXT_CMD.
This is needed since WFDS spec and certification require a P2P client
to be discoverable on its operating channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: avoid read/write operations if the bus is dead
Recovery takes too much time if the bus is dead (each timeout
is 2000ms, etc.).
Explicitly skip fw dump in this case, as it will result in
garbage data (and might take signifcant time)
Avraham Stern [Wed, 19 Aug 2015 09:46:12 +0000 (12:46 +0300)]
iwlwifi: mvm: Add support for two scheduled scan plans
Add support for two scan plans for scheduled scan. The first plan
will run for a limited number of iterations, then the second plan
will run infinitely.
Luca Coelho [Tue, 6 Oct 2015 06:54:57 +0000 (09:54 +0300)]
iwlwifi: mvm: let any command flag be passed to iwl_mvm_flushtx_path()
Instead of only allowing the caller to decide whether the CMD_ASYNC
flag is set, let it pass the entire flags bitmask. This allows more
flexibility and will be needed when we call this function in the
suspend flow (where other flags are needed).
Johannes Berg [Tue, 6 Oct 2015 12:07:44 +0000 (14:07 +0200)]
iwlwifi: mvm: use short timeouts in P2P low latency if supported
Those timeouts are used for AM-to-PSM transition.
We already have those pairs defined for default and WOWLAN use cases.
We expect that by using shorter threshold for low latency P2P,
e.g. for Miracast video scenario, we might save a considerable amount of power.
Arik Nemtsov [Tue, 6 Oct 2015 09:22:47 +0000 (12:22 +0300)]
iwlwifi: mvm: correctly request DTS-measure for new cards
Since the 8000 series, the DTS measurement request command has been
changed. Use an ucode capability flag to determine which version is
supported and send the extended command when needed.
The hardware bug in the commit mentioned below forces us
not to re-enable the clock gating in the Host Cluster.
The impact on the power consumption is minimal and it allows
the WAKE_ME interrupt to propagate.
The TIPC broadcast link implementation is currently complex and hard to
follow. It also incurs some amount of code and structure duplication,
something that can be reduced significantly with a little effort.
This commit series introduces a number of improvements which address
both the locking structure, the code/structure duplication issue, and
the overall readbility of the code.
The series consists of three main parts:
1-7: Adaptation to the new link structure, and preparation for the next
step. In particular, we want the broadcast transmission link to
have a life cycle that is longer than any of its potential (unicast
and broadcast receive links) users. This eliminates the need to
always test for the presence of this link before accessing it.
8-10: This is what is really new in this series. Commit #9 is by far
the largest and most important one, because it moves most of
the broadcast functionality into link.c, partially reusing the
fields and functionality of the unicast link. The removal of
the "node_map" infrastructure in commit #10 is also an important
achievement.
11-16: Some improvements leveraging the changes made in the previous
commits.
The series needs commit 53387c4e22ac ("tipc: extend broadcast link window size")
and commit e53567948f82 ("tipc: conditionally expand buffer headroom over udp tunnel")
which are both present in 'net' but not yet in 'net-next', to apply cleanly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:47 +0000 (08:51 -0400)]
tipc: ensure binding table initial distribution is sent via first link
Correct synchronization of the broadcast link at first contact between
two nodes is dependent on the assumption that the binding table "bulk"
update passes via the same link as the initial broadcast syncronization
message, i.e., via the first link that is established.
This is not guaranteed in the current implementation. If two link
come up very close to each other in time, the "bulk" may quite well
pass via the second link, and hence void the guarantee of a correct
initial synchronization before the broadcast link is opened.
This commit makes two small changes to strengthen this guarantee.
1) We let the second established link occupy slot 1 of the
"active_links" array, while the first link will retain slot 0.
(This is in reality a cosmetic change, we could just as well keep
the current, opposite order)
2) We let the name distributor always use link selector/slot 0 when
it sends it binding table updates.
The extra traffic bias on the first link caused by this change should
be negligible, since binding table updates constitutes a very small
fraction of the total traffic.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:46 +0000 (08:51 -0400)]
tipc: eliminate link's reference to owner node
With the recent commit series, we have established a one-way dependency
between the link aggregation (struct tipc_node) instances and their
pertaining tipc_link instances. This has enabled quite significant code
and structure simplifications.
In this commit, we eliminate the field 'owner', which points to an
instance of struct tipc_node, from struct tipc_link, and replace it with
a pointer to struct net, which is the only external reference now needed
by a link instance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:45 +0000 (08:51 -0400)]
tipc: eliminate redundant buffer cloning at transmission
Since all packet transmitters (link, bcast, discovery) are now sending
consumable buffer clones to the bearer layer, we can remove the
redundant buffer cloning that is perfomed in the lower level functions
tipc_l2_send_msg() and tipc_udp_send_msg().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:44 +0000 (08:51 -0400)]
tipc: let neighbor discoverer tranmsit consumable buffers
The neighbor discovery function currently uses the function
tipc_bearer_send() for transmitting packets, assuming that the
sent buffers are not consumed by the called function.
We want to change this, in order to avoid unnecessary buffer cloning
elswhere in the code.
This commit introduces a new function tipc_bearer_skb() which consumes
the sent buffers, and let the discoverer functions use this new call
instead. The discoverer does now itself perform the cloning when
that is necessary.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:42 +0000 (08:51 -0400)]
tipc: simplify bearer level broadcast
Until now, we have been keeping track of the exact set of broadcast
destinations though the help structure tipc_node_map. This leads us to
have to maintain a whole infrastructure for supporting this, including
a pseudo-bearer and a number of functions to manipulate both the bearers
and the node map correctly. Apart from the complexity, this approach is
also limiting, as struct tipc_node_map only can support cluster local
broadcast if we want to avoid it becoming excessively large. We want to
eliminate this limitation, in order to enable introduction of scoped
multicast in the future.
A closer analysis reveals that it is unnecessary maintaining this "full
set" overview; it is sufficient to keep a counter per bearer, indicating
how many nodes can be reached via this bearer at the moment. The protocol
is now robust enough to handle transitional discrepancies between the
nominal number of reachable destinations, as expected by the broadcast
protocol itself, and the number which is actually reachable at the
moment. The initial broadcast synchronization, in conjunction with the
retransmission mechanism, ensures that all packets will eventually be
acknowledged by the correct set of destinations.
This commit introduces these changes.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:41 +0000 (08:51 -0400)]
tipc: let broadcast packet reception use new link receive function
The code path for receiving broadcast packets is currently distinct
from the unicast path. This leads to unnecessary code and data
duplication, something that can be avoided with some effort.
We now introduce separate per-peer tipc_link instances for handling
broadcast packet reception. Each receive link keeps a pointer to the
common, single, broadcast link instance, and can hence handle release
and retransmission of send buffers as if they belonged to the own
instance.
Furthermore, we let each unicast link instance keep a reference to both
the pertaining broadcast receive link, and to the common send link.
This makes it possible for the unicast links to easily access data for
broadcast link synchronization, as well as for carrying acknowledges for
received broadcast packets.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:40 +0000 (08:51 -0400)]
tipc: introduce capability bit for broadcast synchronization
Until now, we have tried to support both the newer, dedicated broadcast
synchronization mechanism along with the older, less safe, RESET_MSG/
ACTIVATE_MSG based one. The latter method has turned out to be a hazard
in a highly dynamic cluster, so we find it safer to disable it completely
when we find that the former mechanism is supported by the peer node.
For this purpose, we now introduce a new capabability bit,
TIPC_BCAST_SYNCH, to inform any peer nodes that dedicated broadcast
syncronization is supported by the present node. The new bit is conveyed
between peers in the 'capabilities' field of neighbor discovery messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:39 +0000 (08:51 -0400)]
tipc: let broadcast transmission use new link transmit function
This commit simplifies the broadcast link transmission function, by
leveraging previous changes to the link transmission function and the
broadcast transmission link life cycle.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:38 +0000 (08:51 -0400)]
tipc: make struct tipc_link generic to support broadcast
Realizing that unicast is just a special case of broadcast, we also see
that we can go in the other direction, i.e., that modest changes to the
current unicast link can make it generic enough to support broadcast.
The following changes are introduced here:
- A new counter ("ackers") in struct tipc_link, to indicate how many
peers need to ack a packet before it can be released.
- A corresponding counter in the skb user area, to keep track of how
many peers a are left to ack before a buffer can be released.
- A new counter ("acked"), to keep persistent track of how far a peer
has acked at the moment, i.e., where in the transmission queue to
start updating buffers when the next ack arrives. This is to avoid
double acknowledgements from a peer, with inadvertent relase of
packets as a result.
- A more generic tipc_link_retrans() function, where retransmit starts
from a given sequence number, instead of the first packet in the
transmision queue. This is to minimize the number of retransmitted
packets on the broadcast media.
When the new functionality is taken into use in the next commits,
we expect it to have minimal effect on unicast mode performance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:37 +0000 (08:51 -0400)]
tipc: use explicit allocation of broadcast send link
The broadcast link instance (struct tipc_link) used for sending is
currently aggregated into struct tipc_bclink. This means that we cannot
use the regular tipc_link_create() function for initiating the link, but
do instead have to initiate numerous fields directly from the
bcast_init() function.
We want to reduce dependencies between the broadcast functionality
and the inner workings of tipc_link. In this commit, we introduce
a new function tipc_bclink_create() to link.c, and allocate the
instance of the link separately using this function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:36 +0000 (08:51 -0400)]
tipc: make link implementation independent from struct tipc_bearer
In reality, the link implementation is already independent from
struct tipc_bearer, in that it doesn't store any reference to it.
However, we still pass on a pointer to a bearer instance in the
function tipc_link_create(), just to have it extract some
initialization information from it.
I later commits, we need to create instances of tipc_link without
having any associated struct tipc_bearer. To facilitate this, we
want to extract the initialization data already in the creator
function in node.c, before calling tipc_link_create(), and pass
this info on as individual parameters in the call.
This commit introduces this change.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:35 +0000 (08:51 -0400)]
tipc: create broadcast transmission link at namespace init
The broadcast transmission link is currently instantiated when the
network subsystem is started, i.e., on order from user space via netlink.
This forces the broadcast transmission code to do unnecessary tests for
the existence of the transmission link, as well in single mode node as
in network mode.
In this commit, we do instead create the link during initialization of
the name space, and remove it when it is stopped. The fact that the
transmission link now has a guaranteed longer life cycle than any of its
potential clients paves the way for further code simplifcations
and optimizations.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:34 +0000 (08:51 -0400)]
tipc: move broadcast link lock to struct tipc_net
The broadcast lock will need to be acquired outside bcast.c in a later
commit. For this reason, we move the lock to struct tipc_net. Consistent
with the changes in the previous commit, we also introducee two new
functions tipc_bcast_lock() and tipc_bcast_unlock(). The code that is
currently using tipc_bclink_lock()/unlock() will be phased out during
the coming commits in this series.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 22 Oct 2015 12:51:33 +0000 (08:51 -0400)]
tipc: move bcast definitions to bcast.c
Currently, a number of structure and function definitions related
to the broadcast functionality are unnecessarily exposed in the file
bcast.h. This obscures the fact that the external interface towards
the broadcast link in fact is very narrow, and causes unnecessary
recompilations of other files when anything changes in those
definitions.
In this commit, we move as many of those definitions as is currently
possible to the file bcast.c.
We also rename the structure 'tipc_bclink' to 'tipc_bc_base', both
since the name does not correctly describe the contents of this
struct, and will do so even less in the future, and because we want
to use the term 'link' more appropriately in the functionality
introduced later in this series.
Finally, we rename a couple of functions, such as tipc_bclink_xmit()
and others that will be kept in the future, to include the term 'bcast'
instead.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's probably the last bluetooth-next pull request for 4.4. Among
several other changes it contains the rest of the fixes & cleanups from
the Bluetooth UnplugFest (that didn't need to be hurried to 4.3).
- Refactoring & cleanups to 6lowpan code
- New USB ids for two Atheros controllers and BCM43142A0 from Broadcom
- Fix (quirk) for broken Broadcom BCM2045 controllers
- Support for latest Apple controllers
- Improvements to the vendor diagnostic message support
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo [Fri, 23 Oct 2015 17:27:58 +0000 (20:27 +0300)]
rtl8xxxu: move devices supported by rtlwifi under UNTESTED config
There are still four devices which are currently supported both by the new
rtl8xxxu driver and rtlwifi. To not break existing setups enable the support
for these four devices only when CONFIG_RTL8XXXU_UNTESTED is turned on.
Once rtl8xxxu support is found to be good enough the devices can be removed
from rtlwifi and enabled by default in rtl8xxxu.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Michael Chan [Fri, 23 Oct 2015 19:06:19 +0000 (15:06 -0400)]
bnxt_en: Fix compile errors when CONFIG_BNXT_SRIOV is not set.
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac()
to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV.
Reported-by: Jim Hull <jim.hull@hpe.com> Tested-by: Jim Hull <jim.hull@hpe.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 23 Oct 2015 13:58:09 +0000 (06:58 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-23
This series contains updates to i40e, i40evf, if_link, ixgbe and ixgbevf.
Anjali adds a workaround to drop any flow control frames from being
transmitted from any VSI, so that a malicious VF cannot send flow control
or PFC packets out on the wire. Also fixed a bug in debugfs by grabbing
the filter list lock before adding or deleting a filter.
Akeem fixes an issue where we were unconditionally returning VEB bridge
mode before allowing LB in the add VSI routine, resolve by checking if
the bridge is actually in VEB mode first.
Mitch fixed an issue where the incorrect structure was being used for
VLAN filter list, which meant the VLAN filter list did not get
processed correctly and VLAN filters would not be re-enabled after any
kind of reset.
Helin fixed a problem of possibly getting inconsistent flow control
status after a PF reset. The issue was requested_mode was being set
with a default value during probe, but the hardware state could be a
different value from this mode.
Carolyn fixed a problem where the driver output of the OEM version
string varied from the other tools.
Jean Sacren fixes up kernel documentation by fixing function header
comments to match actual variables used in the functions. Also
cleaned up variable initialization, when the variable would be
over-written immediately.
Hiroshi Shimanoto provides three patches to add "trusted" VF by adding
netlink directives and an NDO entry. Then implement these new controls
in ixgbe and ixgbevf. This series has gone through several iterations
to address all the suggested community changes and concerns.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 23 Oct 2015 13:26:50 +0000 (06:26 -0700)]
Merge branch 'mpls_multipath'
Roopa Prabhu says:
====================
mpls: multipath support
This patch adds support for MPLS multipath routes.
Includes following changes to support multipath:
- splits struct mpls_route into 'struct mpls_route + struct mpls_nh'.
- struct mpls_nh represents a mpls nexthop label forwarding entry
- Adds support to parse/fill RTA_MULTIPATH netlink attribute for
multipath routes similar to ipv4/v6 fib
- In the process of restructuring, this patch also consistently changes all
labels to u8
$ip -f mpls route add 100 nexthop as 200 via inet 10.1.1.2 dev swp1 \
nexthop as 700 via inet 10.1.1.6 dev swp2 \
nexthop as 800 via inet 40.1.1.2 dev swp3
$ip -f mpls route show
100
nexthop as to 200 via inet 10.1.1.2 dev swp1
nexthop as to 700 via inet 10.1.1.6 dev swp2
nexthop as to 800 via inet 40.1.1.2 dev swp3
====================
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log