David Howells [Thu, 27 Apr 2017 21:40:23 +0000 (22:40 +0100)]
net: Initialise init_net.count to 1
Initialise init_net.count to 1 for its pointer from init_nsproxy lest
someone tries to do a get_net() and a put_net() in a process in which
current->ns_proxy->net_ns points to the initial network namespace.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
geneve: fix incorrect setting of UDP checksum flag
Creating a geneve link with 'udpcsum' set results in a creation of link
for which UDP checksum will NOT be computed on outbound packets, as can
be seen below.
11: gen0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether c2:85:27:b6:b4:15 brd ff:ff:ff:ff:ff:ff promiscuity 0
geneve id 200 remote 192.168.13.1 dstport 6081 noudpcsum
Similarly, creating a link with 'noudpcsum' set results in a creation
of link for which UDP checksum will be computed on outbound packets.
Fixes: 9b4437a5b870 ("geneve: Unify LWT and netdev handling.") Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: Lance Richardson <lrichard@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The message "Cannot bind port X, err=Y" creates only confusion. In metadata
based mode, failure of IPv6 socket creation is okay if IPv6 is disabled and
no error message should be printed. But when IPv6 tunnel was requested, such
failure is fatal. The vxlan_socket_create does not know when the error is
harmless and when it's not.
Instead of passing such information down to vxlan_socket_create, remove the
message completely. It's not useful. We propagate the error code up to the
user space and the port number comes from the user space. There's nothing in
the message that the process creating vxlan interface does not know.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When IPv6 is compiled but disabled at runtime, __vxlan_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.
Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.
Fixes: b1be00a6c39f ("vxlan: support both IPv4 and IPv6 sockets in a single vxlan device") Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Thu, 27 Apr 2017 13:36:59 +0000 (16:36 +0300)]
bnx2x: Replace custom scnprintf()
Use scnprintf() when printing version instead of custom open coded variants.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The description inside uapi/linux/bpf.h about bpf_get_socket_uid
helper function is no longer valid. It returns overflowuid rather
than 0 when failed.
Signed-off-by: Chenbo Feng <fengc@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
avoid direct access to sk->sk_state when tcp_poll() is called on a socket
using active TCP fastopen with deferred connect. Use local variable
'state', which stores the result of sk_state_load(), like it was done in
commit 00fd38d938db ("tcp: ensure proper barriers in lockless contexts").
Fixes: 19f6d3f3c842 ("net/tcp-fastopen: Add new API support") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 26 Apr 2017 16:09:23 +0000 (09:09 -0700)]
bpf: restore skb->sk before pskb_trim() call
While testing a fix [1] in ___pskb_trim(), addressing the WARN_ON_ONCE()
in skb_try_coalesce() reported by Andrey, I found that we had an skb
with skb->sk set but no skb->destructor.
This invalidated heuristic found in commit 158f323b9868 ("net: adjust
skb->truesize in pskb_expand_head()") and in cited patch.
Considering the BUG_ON(skb->sk) we have in skb_orphan(), we should
restrain the temporary setting to a minimal section.
[1] https://patchwork.ozlabs.org/patch/755570/
net: adjust skb->truesize in ___pskb_trim()
Fixes: 8f917bba0042 ("bpf: pass sk to helper functions") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Andrey Konovalov <andreyknvl@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since 83a77e9ec415, the phydev irq is explicitly set to PHY_POLL when
there is no pdata. It doesn't work on DT enabled platforms because the
phydev irq is already set by libphy before.
Fixes: 83a77e9ec415 ("net: macb: Added PCI wrapper for Platform Driver.") Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 30 Apr 2017 15:33:37 +0000 (11:33 -0400)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-04-30
This series contains updates to i40e and i40evf only.
Jake provides majority of the changes in this series, starting with the
renaming of a flag to avoid confusion. Then renamed a variable to a
more meaningful name to clarify what is actually being done and to
reduce confusion. Amortizes the wait time when initializing or disabling
lots of VFs by using i40e_reset_all_vfs() and
i40e_vsi_stop_rings_no_wait(). Cleaned up a unnecessary delay since
pci_disable_sriov() already has its own delay, so need to add a additional
delay when removing VFs. Avoid using the same name flags for both
vsi->state and pf->state, to make code review easier and assist future
work to use the correct state field when checking bits. Use
DECLARE_BITMAP() to ensure that we always allocate enough space for flags.
Replace hw_disabled_flags with the new _AUTO_DISABLED flags, which are
more readable because we are not setting an *_ENABLED flag to
disable the feature.
Alex corrects a oversight where we were not reprogramming the ports
after a reset, which was causing us to lose all of the receive tunnel
offloads.
Arnd Bergmann moves the declaration of a local variable to avoid a
warning seen on architectures with larger pages about an unused variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 30 Apr 2017 15:30:13 +0000 (11:30 -0400)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-04-30
This series contains updates to e1000e only.
Jarod Wilson fixes an issue where the workaround for 82574 & 82583
is needed for i218 as well, so set the appropriate flags.
Sasha adds support for the upcoming new i219 devices for the client
platform (CannonLake), which includes the support for 38.4MHz frequency
to support PTP on CannonLake.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 38.4MHz frequency is required for PTP
on CannonLake. SYSTIM frequency adjustment attributes for TIMINCA are
get/set dependent on the hardware clock frequency for a different
types of adapters. 38.4MHz frequency supported by CannonLake
and active once time synchronisation mechanism was enabled
Changed abbreviation from Hz to HZ to be compliant checkpatch code style
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Raanan Avargil <raanan.avargil@intel.com> Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219 (6) and i219 (7) are the next LOM generations that will be
available on the nextIntel Client platform (CannonLake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Raanan Avargil <raanan.avargil@intel.com> Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jarod Wilson [Tue, 26 Jul 2016 18:25:35 +0000 (14:25 -0400)]
e1000e: fix PTP on e1000_pch_lpt variants
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On architectures with larger pages, we get a warning about an unused variable:
drivers/net/ethernet/intel/i40evf/i40evf_main.c: In function 'i40evf_configure_rx':
drivers/net/ethernet/intel/i40evf/i40evf_main.c:690:21: error: unused variable 'netdev' [-Werror=unused-variable]
This moves the declaration into the #ifdef to avoid the warning.
Fixes: dab86afdbbd1 ("i40e/i40evf: Change the way we limit the maximum frame size for Rx") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 19 Apr 2017 13:25:59 +0000 (09:25 -0400)]
i40evf: allocate queues before we setup the interrupts and q_vectors
This matches the ordering of how we free stuff during reset and remove.
It also makes logical sense because we set the interrupts based on the
number of queues. Currently this doesn't really matter in practice.
However a future patch moves the assignment of num_active_queues into
i40evf_alloc_queues, which is required by
i40evf_set_interrupt_capability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 19 Apr 2017 13:25:58 +0000 (09:25 -0400)]
i40evf: remove I40E_FLAG_FDIR_ATR_ENABLED
The flag used by the common code and PF code is I40E_FLAG_FD_ATR_ENABLED,
not *FDIR*. It turns out none of the txrx code actually shared with the
VF driver actually checks the ATR flag. This is made even more obvious
by the typo in the VF header file.
Let's just remove the flag from the VF driver since it's not needed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 19 Apr 2017 13:25:57 +0000 (09:25 -0400)]
i40e: remove hw_disabled_flags in favor of using separate flag bits
The hw_disabled_flags field was added as a way of signifying that
a feature was automatically or temporarily disabled. However, we
actually only use this for FDir features. Replace its use with new
_AUTO_DISABLED flags instead. This is more readable, because you aren't
setting an *_ENABLED flag to *disable* the feature.
Additionally, clean up a few areas where we used these bits. First, we
don't really need to set the auto-disable flag for ATR if we're fully
disabling the feature via ethtool.
Second, we should always clear the auto-disable bits in case they somehow
got set when the feature was disabled. However, avoid displaying
a message that we've re-enabled the feature.
Third, we shouldn't be re-enabling ATR in the SB ntuple add flow,
because it might have been disabled due to space constraints. Instead,
we should just wait for the fdir_check_and_reenable to be called by the
watchdog.
Overall, this change allows us to simplify some code by removing an
extra field we didn't need, and the result should make it more clear as
to what we're actually doing with these flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 19 Apr 2017 13:25:56 +0000 (09:25 -0400)]
i40evf: remove needless min_t() on num_online_cpus()*2
We already set pairs to the value of adapter->num_active_queues. This
value is limited by vsi_res->num_queue_pairs and num_online_cpus(). This
means that pairs by definition is already smaller than
num_online_cpus()*2, so we don't even need to bother with this check.
Lets just remove it and update the comment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 19 Apr 2017 13:25:55 +0000 (09:25 -0400)]
i40e: use DECLARE_BITMAP for state fields
Instead of assuming our flags fit within an unsigned long, use
DECLARE_BITMAP which will ensure that we always allocate enough space.
Additionally, use __I40E_STATE_SIZE__ markers as the last element of the
enumeration so that the size of the BITMAP is compile-time assigned
rather than programmer-time assigned. This ensures that potential future
flag additions do not actually overrun the array. This is especially
important as 32bit systems would only have 32bit longs instead of 64bit
longs as we generally have assumed in the prior code.
This change also removes a dereference of the state fields throughout
the code, so it does have a bit of code churn. The conversions were
automated using sed replacements with an alternation
For debugfs, we modify the printing so that we can display chunks of the
state value on new lines. This ensures that we can print the entire set
of state values. Additionally, we now print them as 08lx to ensure that
they display nicely.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Fri, 21 Apr 2017 20:38:05 +0000 (13:38 -0700)]
i40e: separate PF and VSI state flags
Avoid using the same named flags for both vsi->state and pf->state. This
makes code review easier, as it is more likely that future authors will
use the correct state field when checking bits. Previous commits already
found issues with at least one check, and possibly others may be
incorrect.
This reduces confusion as it is more clear what each flag represents,
and which flags are valid for which state field.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 19 Apr 2017 13:25:53 +0000 (09:25 -0400)]
i40e: remove unnecessary msleep() delay in i40e_free_vfs
The delay was added because of a desire to ensure that the VF driver can
finish up removing. However, pci_disable_sriov already has its own
ssleep() call that will sleep for an entire second, so there is no
reason to add extra delay on top of this by using msleep here. In
practice, an msleep() won't have a huge impact on timing but there is no
real value in keeping it, so lets just simplify the code and remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 19 Apr 2017 13:25:52 +0000 (09:25 -0400)]
i40e: amortize wait time when disabling lots of VFs
Just as we do in i40e_reset_all_vfs, save some time when freeing VFs by
amortizing the wait time for stopping queues. We can use
i40e_vsi_stop_rings_no_wait() to begin the process of stopping all the
VF rings at once. Then, once we've started the process on each VF we can
begin waiting for the VFs to stop. This helps reduce the total wait time
by a large factor.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 19 Apr 2017 13:25:51 +0000 (09:25 -0400)]
i40e: Reprogram port offloads after reset
This patch corrects a major oversight in that we were not reprogramming the
ports after a reset. As a result we completely lost all of the Rx tunnel
offloads on receive including Rx checksum, RSS on inner headers, and ATR.
The fix for this is pretty standard as all we needed to do is reset the
filter bits to pending for all active filters and schedule the sync event.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 19 Apr 2017 13:25:50 +0000 (09:25 -0400)]
i40e: rename index to port to avoid confusion
The .index field of i40e_udp_port_config represents the udp port number.
Rename this variable to port so that it is more obvious.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 13 Apr 2017 08:45:55 +0000 (04:45 -0400)]
i40e: make use of i40e_reset_all_vfs when initializing new VFs
When allocating a large number of VFs, the driver previously used
i40e_reset_vf in a sequence. Just as when performing a normal reset,
this accumulates a large amount of delay for handling all of the VFs in
sequence. This delay is mainly due to a hardware requirement to wait
after initiating a reset on the VF.
We recently added a new function, i40e_reset_all_vfs() which can be used
to amortize the delay time, by first triggering all VF resets, then
waiting once, and finally cleaning up and allocating the VFs. This is
almost as good as truly running the resets in parallel.
In order to avoid sending a spurious reset message to a client
interface, we have a check to see whether we've assigned
pf->num_alloc_vfs yet. This was originally intended as a way to
distinguish the "initialization" case from the regular reset case.
Unfortunately, this means that we can't directly use i40e_reset_all_vfs
yet. Lets avoid this check of pf->num_alloc_vfs by replacing it with
a proper VSI state bit which we can use instead. This makes the
intention much clearer and allows us to re-use the i40e_reset_all_vfs
function directly.
Change-ID: I694279b37eb6b5a91b6670182d0c15d10244fd6e Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 13 Apr 2017 08:45:54 +0000 (04:45 -0400)]
i40e: properly spell I40E_VF_STATE_* flags
These flags represent the state of the VF at various times. Do not
spell them as _STAT_ which can be confusing to readers who may think
these refer to statistics.
Change-ID: I6bc092cd472e8276896a1fd7498aced2084312df Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Sun, 30 Apr 2017 03:16:20 +0000 (23:16 -0400)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2017-04-29
This series contains updates to ixgbe and ixgbevf only, most notable is
the addition of XDP support to our 10GbE drivers.
Paul fixes ixgbe to acquire the PHY semaphore before accessing PHY
registers when issuing a device reset.
John adds XDP support (yeah!) for ixgbe.
Emil fixes an issue by flushing the MACVLAN filters on VF reset to avoid
conflicts with other VFs that may end up using the same MAC address. Also
fixed a bug where ethtool -S displayed some empty fields for ixgbevf
because it was using ixgbe_stats instead ixgbevf_stats for
IXGBEVF_QUEUE_STATS_LEN.
Tony adds the ability to specify a zero MAC address in order to clear the
VF's MAC address from the RAR table. Also adds support for a new
1000Base-T device based on x550EM_X MAC type. Fixed an issue where the
RSS key specified by the user would be over-written with a pre-existing
value, so change the rss_key to a pointer so we can check to see if the
key has a value set before attempting to set it. Fixed the logic for
mailbox support for getting RETA and RSS values, which are only supported
by 82599 and x540 devices.
v2: fixed up patches #2 and #3 based on feedback from Jakub and to
address build issues when page sizes are larger than 4k
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen [Thu, 13 Apr 2017 14:26:07 +0000 (07:26 -0700)]
ixgbevf: Check for RSS key before setting value
The RSS key is being repopulated every time the interface is brought up
regardless of whether there is an existing value. If the user sets the RSS
key and the interface is brought up (e.g. reset), the user specified RSS
key will be overwritten.
This patch changes the rss_key to a pointer so we can check to see if the
key has been populated and preserve it accordingly.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Nguyen [Thu, 13 Apr 2017 14:26:06 +0000 (07:26 -0700)]
ixgbevf: Fix errors in retrieving RETA and RSS from PF
Mailbox support for getting RETA and RSS is available for only 82599 and
x540; a previous patch reversed the logic and these adapters were
returning not supported.
Also, the NACK check in ixgbevf_get_rss_key_locked() was checking for the
command IXGBE_VF_GET_RETA instead of IXGBE_VF_GET_RSS_KEY.
This patch corrects both issues by correcting the logic and checking for
the right command.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Nguyen [Thu, 13 Apr 2017 14:26:05 +0000 (07:26 -0700)]
ixgbe: Check for RSS key before setting value
The RSS key is being repopulated every time the interface is brought up
regardless of whether there is an existing value. If the user sets the RSS
key and the interface is brought up (e.g. reset), the user specified RSS
key will be overwritten.
This patch changes the rss_key to a pointer so we can check to see if the
key has been populated and preserve it accordingly.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Nguyen [Wed, 12 Apr 2017 20:35:22 +0000 (13:35 -0700)]
ixgbe: Allow setting zero MAC address for VF
Currently, there is no logic that allows a VF's MAC address to be removed
from the RAR table.
Allow the user to specify a zero MAC address in order to clear the VF's
MAC address from the RAR table. This functionality is also utilized by
libvirt when removing VFs.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Fri, 31 Mar 2017 03:49:02 +0000 (20:49 -0700)]
ixgbevf: fix size of queue stats length
IXGBEVF_QUEUE_STATS_LEN is based on ixgebvf_stats, not ixgbe_stats.
This change fixes a bug where ethtool -S displayed some empty fields.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Tue, 28 Mar 2017 16:47:03 +0000 (09:47 -0700)]
ixgbe: delay tail write to every 'n' packets
Current XDP implementation hits the tail on every XDP_TX return
code. This patch changes driver behavior to only hit the tail after
packet processing is complete.
With this patch I can run XDP drop programs @ 14+Mpps and XDP_TX
programs are at ~13.5Mpps.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Mon, 24 Apr 2017 10:30:18 +0000 (03:30 -0700)]
ixgbe: add support for XDP_TX action
A couple design choices were made here. First I use a new ring
pointer structure xdp_ring[] in the adapter struct instead of
pushing the newly allocated XDP TX rings into the tx_ring[]
structure. This means we have to duplicate loops around rings
in places we want to initialize both TX rings and XDP rings.
But by making it explicit it is obvious when we are using XDP
rings and when we are using TX rings. Further we don't have
to do ring arithmatic which is error prone. As a proof point
for doing this my first patches used only a single ring structure
and introduced bugs in FCoE code and macvlan code paths.
Second I am aware this is not the most optimized version of
this code possible. I want to get baseline support in using
the most readable format possible and then once this series
is included I will optimize the TX path in another series
of patches.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Mon, 24 Apr 2017 10:30:17 +0000 (03:30 -0700)]
ixgbe: add XDP support for pass and drop actions
Basic XDP drop support for ixgbe. Uses READ_ONCE/xchg semantics on XDP
programs instead of RCU primitives as suggested by Daniel Borkmann and
Alex Duyck.
v2: fix the build issues seen w/ XDP when page sizes are larger than 4K
and made minor fixes based on feedback from Jakub Kicinski
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Paul Greenwalt [Mon, 13 Mar 2017 09:47:56 +0000 (05:47 -0400)]
ixgbe: Acquire PHY semaphore before device reset
A recent firmware change fixed an issue to acquire the PHY semaphore before
accessing PHY registers. This led to a case where SW can issue a device
reset clearing the MDIO registers. This patch makes SW acquire the PHY
semaphore before issuing a device reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Fri, 28 Apr 2017 19:48:16 +0000 (15:48 -0400)]
Merge branch 'bpf-misc-next'
Daniel Borkmann says:
====================
Misc BPF updates
This set cleans up ldimm64 leftovers from early eBPF days and
adds couple of test cases related to this to the verifier test
suite. It also cleans up the kallsyms spinlock (had same patch
also in queue) by relaxing it through switching to _bh variant.
It fixes up test_progs in relation to htons/ntohs and adds
accessor macros for the percpu tests in test_maps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 26 Apr 2017 23:39:35 +0000 (01:39 +0200)]
bpf: provide a generic macro for percpu values for selftests
To overcome bugs as described and fixed in 89087c456fb5 ("bpf: Fix
values type used in test_maps"), provide a generic BPF_DECLARE_PERCPU()
and bpf_percpu() accessor macro for all percpu map values used in
tests.
Declaring variables works as follows (also works for structs):
BPF_DECLARE_PERCPU(uint32_t, my_value);
They can then be accessed normally as uint32_t type through:
bpf_percpu(my_value, <cpu_nr>)
For example:
bpf_percpu(my_value, 0)++;
Implicitly, we make sure that the passed type is allocated and aligned
by gcc at least on a 8-byte boundary, so that it works together with
the map lookup/update syscall for percpu maps. We use it as a usage
example in test_maps, so that others are free to adapt this into their
code when necessary.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
... in test_progs that causes this. Make use of asm/byteorder.h
and use __constant_htons() where possible and only perform the
bswap16 when on little endian in non-constant case.
Fixes: 6882804c916b ("selftests/bpf: add a test for overlapping packet range checks") Fixes: 37821613626e ("selftests/bpf: add l4 load balancer test based on sched_cls") Reported-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
bpf: bpf_lock on kallsysms doesn't need to be irqsave
Hannes rightfully spotted that the bpf_lock doesn't need to be
irqsave variant. We never perform any such updates where this
would be necessary (neither right now nor in future), therefore
relax this further.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 26 Apr 2017 23:39:32 +0000 (01:39 +0200)]
bpf: add various test cases to verifier selftests
Add several test cases around ldimm64, fp arithmetic and direct
packet access.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 26 Apr 2017 23:39:31 +0000 (01:39 +0200)]
bpf, x86_64/arm64: remove old ldimm64 artifacts from jits
For both cases, the verifier is already rejecting such invalid
formed instructions. Thus, remove these artifacts from old times
and align it with ppc64, sparc64 and s390x JITs that don't have
them in the first place.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 28 Apr 2017 18:41:15 +0000 (14:41 -0400)]
Merge tag 'mac80211-next-for-davem-2017-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of patches for -next:
* API support for concurrent scheduled scan requests
* API changes for roaming reporting
* BSS max idle support in mac80211
* API changes for TX status reporting in mac80211
* API changes for RX rate reporting in mac80211
* rewrite monitor logic to prepare for BPF filters
* bugfix for rare devices without 2.4 GHz support
* a bugfix for recent DFS changes
* some further cleanups
The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 28 Apr 2017 06:10:48 +0000 (14:10 +0800)]
rhashtable: Do not lower max_elems when max_size is zero
The commit 6d684e54690c ("rhashtable: Cap total number of entries
to 2^31") breaks rhashtable users that do not set max_size. This
is because when max_size is zero max_elems is also incorrectly set
to zero instead of 2^31.
This patch fixes it by only lowering max_elems when max_size is not
zero.
Fixes: 6d684e54690c ("rhashtable: Cap total number of entries to 2^31") Reported-by: Florian Fainelli <f.fainelli@gmail.com> Reported-by: kernel test robot <fengguang.wu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
cfg80211: add request id to cfg80211_sched_scan_*() api
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: Add support for BSS max idle period element
Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.
The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
cfg80211: unify cfg80211_roamed() and cfg80211_roamed_bss()
cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.
Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly] Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: Fix possible sband related NULL pointer de-reference
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Wed, 26 Apr 2017 15:11:37 +0000 (17:11 +0200)]
mac80211: add ieee80211_tx_status_ext
This allows the driver to pass in struct ieee80211_tx_status directly.
Make ieee80211_tx_status_noskb a wrapper around it.
As with ieee80211_tx_status_noskb, there is no _ni variant of this call,
because it probably won't be needed.
Even if the driver won't provide any extra status info other than what's
in struct ieee80211_tx_info already, it can optimize status reporting
this way by passing in the station pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[use C99 initializers] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Thu, 27 Apr 2017 20:51:35 +0000 (16:51 -0400)]
Merge branch 'qed-ptp-enhancements'
Sudarsana Reddy Kalluru says:
====================
qed*: PTP enhancements.
The patch series contains set of enhancements for qed/qede ptp
implementation.
Patches (1)-(3) adds resource locking implementation to allow
PTP functionality only on the first detected ethernet PF of the port.
The change is required as the adapter currently supports only one
instance of the PTP client on a given port.
Patch (4) removes the un-needed header file.
Patch (5) moves the ptt-lock get/release logic to the ptp specific
code.
Please consider applying this series to "net-next" branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Acquire/release ptt_ptp lock when enabling/disabling PTP.
Move the code for acquiring/releasing ptt_ptp lock to ptp specific
implementations i.e., ptp_enable()/disable() respectively.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch deletes the qed_ptp.h file which is not required.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds necessary changes to the driver to use qed resource
locking functionality. Currently the ptp initialization is spread
between driver probe/open implementations, associated APIs are
qede_ptp_register_phc()/qede_ptp_start(). Clubbed this functionality
into single API qed_ptp_enable() to simplify the usage of qed resource
locking implementation. The new API will be invoked in the probe path.
Similarly the ptp clean-up code is moved to qede_ptp_disable() which
gets invoked in the driver unload path.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for per-port resource lock in favour of PTP.
PTP module acquires/releases the MFW resource lock while enabling/
disabling the PTP on the interface. The PF instance which has the
ownership of this resource lock will get the exclusive access to the
PTP clock functionality on the port.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds API for default initialization of the MFW resource
locking.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 26 Apr 2017 14:58:22 +0000 (07:58 -0700)]
net: vrf: Do not allow looback to be moved to a VRF
Moving the loopback into a VRF breaks networking for the default VRF.
Since the VRF device is the loopback for VRF domains, there is no
reason to move the loopback. Given the repercussions, block attempts
to set lo into a VRF.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -EINVAL from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 622ec2c9d524 ("net: core: add UID to flows, rules, and routes") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Wed, 26 Apr 2017 13:48:09 +0000 (14:48 +0100)]
bridge: add per-port broadcast flood flag
Support for l2 multicast flood control was added in commit b6cb5ac8331b
("net: bridge: add per-port multicast flood flag"). It allows broadcast
as it was introduced specifically for unknown multicast flood control.
But as broadcast is a special case of multicast, this may also need to
be disabled. For this purpose, introduce a flag to disable the flooding
of received l2 broadcasts. This approach is backwards compatible and
provides flexibility in filtering for the desired packet types.
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Mike Manning <mmanning@brocade.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp: remove useless device duplication test in l2tp_eth_create()
There's no need to verify that cfg->ifname is unique at this point.
register_netdev() will return -EEXIST if asked to create a device with
a name that's alrealy in use.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 27 Apr 2017 16:11:13 +0000 (09:11 -0700)]
samples/bpf: Add support for SKB_MODE to xdp1 and xdp_tx_iptunnel
Add option to xdp1 and xdp_tx_iptunnel to insert xdp program in
SKB_MODE:
- update set_link_xdp_fd to take a flags argument that is added to the
RTM_SETLINK message
- Add -S option to xdp1 and xdp_tx_iptunnel user code. When passed in
XDP_FLAGS_SKB_MODE is set in the flags arg passed to set_link_xdp_fd
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Thu, 27 Apr 2017 05:44:51 +0000 (13:44 +0800)]
rhashtable: Cap total number of entries to 2^31
When max_size is not set or if it set to a sufficiently large
value, the nelems counter can overflow. This would cause havoc
with the automatic shrinking as it would then attempt to fit a
huge number of entries into a tiny hash table.
This patch fixes this by adding max_elems to struct rhashtable
to cap the number of elements. This is set to 2^31 as nelems is
not a precise count. This is sufficiently smaller than UINT_MAX
that it should be safe.
When max_size is set max_elems will be lowered to at most twice
max_size as is the status quo.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 27 Apr 2017 04:10:55 +0000 (21:10 -0700)]
tcp: tcp_rack_reo_timeout() must update tp->tcp_mstamp
I wrongly assumed tp->tcp_mstamp was up to date at the time
tcp_rack_reo_timeout() was called.
It is not true, since we only update tcp->tcp_mstamp when receiving
a packet (as initially done in commit 69e996c58a35 ("tcp: add
tp->tcp_mstamp field")
tcp_rack_reo_timeout() being called by a timer and not an incoming
packet, we need to refresh tp->tcp_mstamp
Fixes: 7c1c7308592f ("tcp: do not pass timestamp to tcp_rack_detect_loss()") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Wed, 26 Apr 2017 18:14:34 +0000 (20:14 +0200)]
can: fix CAN BCM build with CONFIG_PROC_FS disabled
The introduced namespace support moved the BCM variables for procfs into a
per-net data structure. This leads to a build failure with disabled procfs:
on x86_64:
when CONFIG_PROC_FS is not enabled:
../net/can/bcm.c:1541:14: error: 'struct netns_can' has no member named 'bcmproc_dir'
../net/can/bcm.c:1601:14: error: 'struct netns_can' has no member named 'bcmproc_dir'
../net/can/bcm.c:1696:11: error: 'struct netns_can' has no member named 'bcmproc_dir'
../net/can/bcm.c:1707:15: error: 'struct netns_can' has no member named 'bcmproc_dir'
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David Howells [Wed, 26 Apr 2017 21:15:55 +0000 (22:15 +0100)]
statx: Kill fd-with-NULL-path support in favour of AT_EMPTY_PATH
With the new statx() syscall, the following both allow the attributes of
the file attached to a file descriptor to be retrieved:
statx(dfd, NULL, 0, ...);
and:
statx(dfd, "", AT_EMPTY_PATH, ...);
Change the code to reject the first option, though this means copying
the path and engaging pathwalk for the fstat() equivalent. dfd can be a
non-directory provided path is "".
[ The timing of this isn't wonderful, but applying this now before we
have statx() in any released kernel, before anybody starts using the
NULL special case. - Linus ]
Fixes: a528d35e8bfc ("statx: Add a system call to make enhanced file info available") Reported-by: Michael Kerrisk <mtk.manpages@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Sandeen <sandeen@sandeen.net>
cc: fstests@vger.kernel.org
cc: linux-api@vger.kernel.org
cc: linux-man@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Wed, 26 Apr 2017 07:58:53 +0000 (10:58 +0300)]
mac80211: disentangle iflist_mtx and chanctx_mtx
At least on iwlwifi, sometimes lockdep complains that we can
lock
chanctx_mtx -> mvm.mutex -> iflist_mtx
(due to iterate_interfaces)
and
iflist_mtx -> chanctx_mtx
Remove the latter dependency in mac80211 by using the RTNL
that we already hold in one case, and can relatively easily
achieve in the other case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: don't parse encrypted management frames in ieee80211_frame_acked
ieee80211_frame_acked is called when a frame is acked by
the peer. In case this is a management frame, we check
if this an SMPS frame, in which case we can update our
antenna configuration.
When we parse the management frame we look at the category
in case it is an action frame. That byte sits after the IV
in case the frame was encrypted. This means that if the
frame was encrypted, we basically look at the IV instead
of looking at the category. It is then theorically
possible that we think that an SMPS action frame was acked
where really we had another frame that was encrypted.
Since the only management frame whose ack needs to be
tracked is the SMPS action frame, and that frame is not
a robust management frame, it will never be encrypted.
The easiest way to fix this problem is then to not look
at frames that were encrypted.
cfg80211: add request id parameter to .sched_scan_stop() signature
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211: allow multiple active scheduled scan requests
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to allocate a portid structure and then, for
each of those, walk the interfaces - we can just add a flag
to each interface and walk those directly. Due to padding in
the struct, we can even do it without any memory cost, and
it even simplifies the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) MLX5 bug fixes from Saeed Mahameed et al:
- released wrong resources when firmware timeout happens
- fix wrong check for encapsulation size limits
- UAR memory leak
- ETHTOOL_GRXCLSRLALL failed to fill in info->data
2) Don't cache l3mdev on mis-matches local route, causes net devices to
leak refs. From Robert Shearman.
3) Handle fragmented SKBs properly in macsec driver, the problem is
that we were mis-sizing the sgvec table. From Jason A. Donenfeld.
4) We cannot have checksum offload enabled for inner UDP tunneled
packet during IPSEC, from Ansis Atteka.
5) Fix double SKB free in ravb driver, from Dan Carpenter.
6) Fix CPU port handling in b53 DSA driver, from Florian Dainelli.
7) Don't use on-stack buffers for usb_control_msg() in CAN usb driver,
from Maksim Salau.
8) Fix device leak in macvlan driver, from Herbert Xu. We have to purge
the broadcast queue properly on port destroy.
9) Fix tx ring entry limit on EF10 devices in sfc driver. From Bert
Kenward.
10) Fix memory leaks in team driver, from Pan Bian.
11) Don't setup ipv6_stub before it can be actually used, from Paolo
Abeni.
12) Fix tipc socket flow control accounting, from Parthasarathy
Bhuvaragan.
13) Fix crash on module unload in hso driver, from Andreas Kemnade.
14) Fix purging of bridge multicast entries, the problem is that if we
don't defer it to ndo_uninit it's possible for new entries to get
added after we purge. Fix from Xin Long.
15) Don't return garbage for PACKET_HDRLEN getsockopt, from Alexander
Potapenko.
16) Fix autoneg stall properly in PHY layer, and revert micrel driver
change that was papering over it. From Alexander Kochetkov.
17) Don't dereference an ipv4 route as an ipv6 one in the ip6_tunnnel
code, from Cong Wang.
18) Clear out the congestion control private of the TCP socket in all of
the right places, from Wei Wang.
19) rawv6_ioctl measures SKB length incorrectly, fix from Jamie
Bainbridge.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ipv6: check raw payload size correctly in ioctl
tcp: memset ca_priv data to 0 properly
ipv6: check skb->protocol before lookup for nexthop
net: core: Prevent from dereferencing null pointer when releasing SKB
macsec: dynamically allocate space for sglist
Revert "phy: micrel: Disable auto negotiation on startup"
net: phy: fix auto-negotiation stall due to unavailable interrupt
net/packet: check length in getsockopt() called with PACKET_HDRLEN
net: ipv6: regenerate host route if moved to gc list
bridge: move bridge multicast cleanup to ndo_uninit
ipv6: fix source routing
qed: Fix error in the dcbx app meta data initialization.
netvsc: fix calculation of available send sections
net: hso: fix module unloading
tipc: fix socket flow control accounting error at tipc_recv_stream
tipc: fix socket flow control accounting error at tipc_send_stream
ipv6: move stub initialization after ipv6 setup completion
team: fix memory leaks
sfc: tx ring can only have 2048 entries for all EF10 NICs
macvlan: Fix device ref leak when purging bc_queue
...
In situations where an skb is paged, the transport header pointer and
tail pointer can be the same because the skb contents are in frags.
This results in ioctl(SIOCINQ/FIONREAD) incorrectly returning a
length of 0 when the length to receive is actually greater than zero.
skb->len is already correctly set in ip6_input_finish() with
pskb_pull(), so use skb->len as it always returns the correct result
for both linear and paged data.
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Wed, 26 Apr 2017 00:38:02 +0000 (17:38 -0700)]
tcp: memset ca_priv data to 0 properly
Always zero out ca_priv data in tcp_assign_congestion_control() so that
ca_priv data is cleared out during socket creation.
Also always zero out ca_priv data in tcp_reinit_congestion_control() so
that when cc algorithm is changed, ca_priv data is cleared out as well.
We should still zero out ca_priv data even in TCP_CLOSE state because
user could call connect() on AF_UNSPEC to disconnect the socket and
leave it in TCP_CLOSE state and later call setsockopt() to switch cc
algorithm on this socket.
Fixes: 2b0a8c9ee ("tcp: add CDG congestion control") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Tue, 25 Apr 2017 21:37:15 +0000 (14:37 -0700)]
ipv6: check skb->protocol before lookup for nexthop
Andrey reported a out-of-bound access in ip6_tnl_xmit(), this
is because we use an ipv4 dst in ip6_tnl_xmit() and cast an IPv4
neigh key as an IPv6 address:
neigh = dst_neigh_lookup(skb_dst(skb),
&ipv6_hdr(skb)->daddr);
if (!neigh)
goto tx_err_link_failure;
if (addr_type == IPV6_ADDR_ANY)
addr6 = &ipv6_hdr(skb)->daddr;
memcpy(&fl6->daddr, addr6, sizeof(fl6->daddr));
Also the network header of the skb at this point should be still IPv4
for 4in6 tunnels, we shold not just use it as IPv6 header.
This patch fixes it by checking if skb->protocol is ETH_P_IPV6: if it
is, we are safe to do the nexthop lookup using skb_dst() and
ipv6_hdr(skb)->daddr; if not (aka IPv4), we have no clue about which
dest address we can pick here, we have to rely on callers to fill it
from tunnel config, so just fall to ip6_route_output() to make the
decision.
Fixes: ea3dc9601bda ("ip6_tunnel: Add support for wildcard tunnel endpoints.") Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Tue, 25 Apr 2017 19:59:17 +0000 (15:59 -0400)]
virtio-net: on tx, only call napi_disable if tx napi is on
As of tx napi, device down (`ip link set dev $dev down`) hangs unless
tx napi is enabled. Else napi_enable is not called, so napi_disable
will spin on test_and_set_bit NAPI_STATE_SCHED.
Only call napi_disable if tx napi is enabled.
Fixes: 5a719c2552ca ("virtio-net: transmit napi") Reported-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log