Documentation: mfd: s2mps11: Describe S5M8767 and S2MPS14 clocks
Add bindings documentation for clocks on S5M8767 and S2MPS14 devices.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Axel Lin [Sat, 15 Mar 2014 01:24:50 +0000 (09:24 +0800)]
mfd: bcm590xx: Fix type argument for module device table
This fixes below build error.
FATAL: drivers/mfd/bcm590xx: sizeof(struct i2c_device_id)=24 is not a modulo of the size of section __mod_i2c_device_table=392.
Fix definition of struct i2c_device_id in mod_devicetable.h
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Peter Tyser [Mon, 10 Mar 2014 21:34:57 +0000 (16:34 -0500)]
mfd: lpc_ich: Add support for NM10 GPIO
The NM10's GPIO is compatible with ICH v7 GPIO.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Dan Weinlader <danw@vs-networks.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Peter Tyser [Mon, 10 Mar 2014 21:34:56 +0000 (16:34 -0500)]
mfd: lpc_ich: Change Avoton to iTCO v3
The register layout of the Avoton is compatible with the iTCO v3
register layout.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Rajat Jain <rajatjain@juniper.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Peter Tyser [Mon, 10 Mar 2014 21:34:55 +0000 (16:34 -0500)]
watchdog: iTCO_wdt: Add support for v3 silicon
Some new Atom's, eg Avoton and Bay Trail, have slightly different iTCO
functionality:
- The watchdog timer ticks at 1 second instead of .6 seconds
- Some 8 and 16-bit registers were combined into 32-bit registers
- Some registers were removed (DAT_IN, DAT_OUT, MESSAGE)
- The BOOT_STS field in TCO_STS was removed
- The NO_REBOOT bit is in the PMC area instead of GCS
Update the driver to support the above changes and bump the version to
1.11.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Rajat Jain <rajatjain@juniper.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Peter Tyser [Mon, 10 Mar 2014 21:34:54 +0000 (16:34 -0500)]
mfd: lpc_ich: Add support for iTCO v3
Some newer Atom CPUs, eg Avoton and Bay Trail, use slightly different
register layouts for the iTCO than the current v1 and v2 iTCO.
Differences from previous iTCO versions include:
- The ACPI space is enabled in the "ACPI base address" register instead
of the "ACPI control register"
- The "no reboot" functionality is set in the "Power Management
Configuration" register instead of the "General Control and Status"
(GCS) register or PCI configuration space.
- The "ACPI Control Register" is not present on v3. The "Power
Management Configuration Base Address" register resides at the same
address is Avoton/Bay Trail.
To differentiate these newer chipsets create a new v3 iTCO version and
update the MFD driver to support them.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Rajat Jain <rajatjain@juniper.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Peter Tyser [Mon, 10 Mar 2014 21:34:53 +0000 (16:34 -0500)]
mfd: lpc_ich: Remove lpc_ich_cfg struct use
Future chipsets will use different register layouts that don't map
cleanly to the lpc_ich_cfg fields. Remove the lpc_ich_cfg struct and
add explicit fields to the higher level lpc_ich_priv structure.
This change should have no functional impact.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Rajat Jain <rajatjain@juniper.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Peter Tyser [Mon, 10 Mar 2014 21:34:52 +0000 (16:34 -0500)]
mfd: lpc_ich: Only configure watchdog or GPIO when present
Some chipsets don't currently have GPIO support enabled. For these
chipsets don't go through the process of initializing the GPIO region.
Make the same change for the watchdog initialization for chipsets which
may not enable the WDT in the future.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Rajat Jain <rajatjain@juniper.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Peter Tyser [Mon, 10 Mar 2014 21:34:51 +0000 (16:34 -0500)]
mfd: lpc_ich: Fix ACPI enable bitmask
The original bitmask of 0x10 was incorrect and would result in a write
to a reserved read-only bit instead of enabling the ACPI I/O
region. Update it to the proper value of 0x80.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Rajat Jain <rajatjain@juniper.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Matt Porter [Tue, 11 Mar 2014 23:33:54 +0000 (19:33 -0400)]
mfd: Add bcm590xx pmu driver
Add a driver for the BCM590xx PMU multi-function devices. The driver
initially supports regmap initialization and instantiation of the
voltage regulator device function of the PMU.
Signed-off-by: Matt Porter <mporter@linaro.org> Reviewed-by: Tim Kryger <tim.kryger@linaro.org> Reviewed-by: Markus Mayer <markus.mayer@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Matt Porter [Wed, 12 Mar 2014 14:07:13 +0000 (10:07 -0400)]
mfd: Add bcm590xx pmu DT binding
Add a DT binding for the BCM590xx PMUs. The binding inherits from
the generic regulator bindings.
Signed-off-by: Matt Porter <mporter@linaro.org> Reviewed-by: Tim Kryger <tim.kryger@linaro.org> Reviewed-by: Markus Mayer <markus.mayer@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tomas Novotny [Mon, 10 Mar 2014 18:12:50 +0000 (19:12 +0100)]
mfd: twl-core: Fix accessibility of some twl4030 audio registers
There are some unused registers in twl4030 at I2C address 0x49 and function
twl4030_49_nop_reg() is used to check accessibility of that registers. These
registers are written in decimal format but the values are correct in
hexadecimal format. (It can be checked few lines above the patched code -
these registers are marked as unused there.)
As a consequence three registers of audio submodule are treated as
inaccessible (preamplifier carkit right and both handsfree registers).
Cc: stable@vger.kernel.org Signed-off-by: Tomas Novotny <tomas@novotny.cz> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: da9063: Upgrade of register definitions to support production silicon
This patch updates the register definitions for DA9063 to support the
production silicon variant code ID (0x5). These changes are not backwards
compatible with the previous register definitions and can only be used
with the production variant of DA9063.
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Alexander Shiyan [Mon, 10 Mar 2014 10:57:33 +0000 (14:57 +0400)]
mfd: syscon: Simplify syscon_match_pdevname()
Since we do not want to add new platform IDs for the syscon driver,
there is no reason to iterate over IDs. This patch simplifies
syscon_match_pdevname() function to remove such iteration.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adam Thomson [Wed, 5 Mar 2014 14:18:37 +0000 (14:18 +0000)]
mfd: da9055: Add DT binding documentation for PMIC
Acked-by: Mark Brown <broonie@kernel.org> Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stephen Warren [Tue, 4 Mar 2014 16:50:32 +0000 (09:50 -0700)]
mfd: as3722: Make FUSE7_REG readable
The FUSE7_REG register is not currently marked readable. This causes
as3722_sd0_is_low_voltage() to emit an error during boot, and assume
the range of the SD0 regulator:
Fixes: d4807ad2c4c0 ("regmap: Check readable regs in _regmap_read")
[exposed the bug, by checking for readability] Fixes: 762a8ee80897 ("regulator: as3722: detect SD0 low-voltage mode")
[left out this register from the readable list]
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stephen Boyd [Tue, 4 Mar 2014 18:48:52 +0000 (10:48 -0800)]
mfd: pm8921: Use IRQCHIP_SKIP_SET_WAKE
We don't need to implement a dummy irq_set_wake op if we just set
IRQCHIP_SKIP_SET_WAKE.
Suggested-by: Josh Cartwright <joshc@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: timberdale: Use pci_enable_msix_exact() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
PM8921 and PM8058 are PMICs found paired with MSM8960 and MSM8660
devices respectively. They contain subdevices such as keypads,
RTC, regulators, clocks, etc.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stephen Boyd [Wed, 26 Feb 2014 18:59:20 +0000 (10:59 -0800)]
mfd: pm8921: Update for genirq changes
Since this code has been marked broken for some time a few genirq
tree wide changes weren't made. set_irq_wake() was renamed to
irq_set_irq_wake() in commit a0cd9ca2b (genirq: Namespace
cleanup, 2011-02-10) and commit 10a8c383 (irq: introduce entry
and exit functions for chained handlers) introduced the chained
irq functions but this driver wasn't updated to use them. Fix
these problems and remove the BROKEN marking on this driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stephen Boyd [Wed, 26 Feb 2014 18:59:19 +0000 (10:59 -0800)]
mfd: pm8xxx: Move pm8xxx-irq.c contents into only driver that uses it
The pm8xxx-irq.c code is practically mandatory given that the
pm8921-core driver will WARN about it missing and the Kconfig
marks it as default y when a PM8xxx chips is enabled. The only
reason the file was split out was because we planned to support
other pm8xxx chips with different pm8xxx-core.c files. Now that
we have DT on ARM this isn't necessary because we should be able
to support all the ssbi based PM8xxx chips in one driver and one
file with no data bloat. Let's move this code into the only
driver that uses it right now (pm8921) so that it's always compiled when
needed. In the future we can rename pm8921-core.c to something
more generic.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Florian Vaussard [Tue, 25 Feb 2014 13:28:19 +0000 (14:28 +0100)]
mfd: twl6040: Check for error when reading revision register
We may have an error when reading the revision register, so check for
the returned value.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Florian Vaussard [Tue, 25 Feb 2014 13:28:20 +0000 (14:28 +0100)]
mfd: twl6040: Remove duplicate register write
When probing, regmap_register_patch() will bypass the cache and perform
i2c writes for the given patches. It is thus unnecessary to manually set
the TWL6040_REG_ACCCTL register just before, as it will be done when
registering the twl6040_patch.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Michael Brunner [Mon, 24 Feb 2014 07:53:46 +0000 (08:53 +0100)]
mfd: kempld: Add support for COMe-mBT10, COMe-cBT6 and COMe-cHL6 to Kontron PLD driver
This patch adds DMI system IDs for the Kontron modules COMe-mBT10, COMe-cBT6
and COMe-cHL6 to the Kontron PLD driver. The list of supported products in
the module description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com> Acked-by: Christian Rauch <christian.rauch@kontron.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for Atom C2000 series (Avoton and Rangeley). And has
the following options:
- New addresses register.
- Caching output levels (see Intel external design spec, table 48-29)
- No hardware blink.
Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch allows GPIO driver to cache GPIO_LVL output registers. The aim is to
support chipsets on which GPIO_LVL value can't be read for output pins.
Caching output levels implies the first output values reading as 0. The driver
so can't be aware of set values GPIOs by bootloader or BIOS.
Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
gpio: ich: Add support for multiple register addresses
This patch introduces regs and reglen pointers which allow a chipset to have
register addresses differing from ICH ones.
Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch allows gpio_ich driver to be aware of non blink capable chipsets.
Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: da9063: Add support for production silicon variant code
Add the correct silicon variant code ID (0x5) to the driver. This
new code is the 'production' variant code ID for DA9063.
This patch will remove the older variant code ID which matches the
pre-production silicon ID (0x3) for the DA9063 chip.
There is also some small amount of correction done in this patch:
it splits the revision code and correctly names it according to
the hardware specification and moves the dev_info() call before
the variant ID test.
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Roger Tseng [Wed, 12 Feb 2014 10:00:36 +0000 (18:00 +0800)]
mfd: Add realtek USB card reader driver
Realtek USB card reader provides a channel to transfer command or data to flash
memory cards. This driver exports host instances for mmc and memstick subsystems
and handles basic works.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Roger Tseng <rogerable@realtek.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: 88pm800: Fix I2C device resource leak if probe fails
During probe the driver allocates two dummy I2C devices for subchips in
function pm800_pages_init(). Additionally this function allocates
regmaps for these subchips. If any of these steps fail then these dummy
I2C devices are not freed and resources leak.
On pm800_pages_init() fail the driver must call pm800_pages_exit() to
unregister dummy I2C devices.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Jingoo Han [Wed, 12 Feb 2014 05:31:49 +0000 (14:31 +0900)]
mfd: ti_am335x_tscadc: Use devm_ioremap_resource()
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Three of the PMIC registers have some bits that are changed
autonomously by the PMIC itself (some time) after being set
by some component driver of the DA9052 PMIC and hence they
need to be marked as volatile so that the regmap API will
not cache their values.
Acked-by: David Dajun Chen <david.chen@diasemi.com> Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: max77693: Fix possible NULL pointer dereference on i2c_new_dummy error
During probe the driver allocates dummy I2C devices for MUIC and haptic
with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by devm_regmap_init_i2c() and i2c_unregister_device().
If i2c_new_dummy() fails for MUIC or haptic devices, fail also the probe
for main MFD driver.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: 88pm860x: Fix possible NULL pointer dereference on i2c_new_dummy error
During probe the driver allocates dummy I2C device for companion chip
with i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by regmap_init_i2c().
If i2c_new_dummy() fails for companion device, fail also the probe for
main MFD driver.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
During probe the driver allocates dummy I2C device for companion chip
and then allocates a regmap for it. If regmap_init_i2c() fails then the
I2C driver (allocated with i2c_new_dummy()) is not freed and this
resource leaks.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: max8925: Fix possible NULL pointer dereference on i2c_new_dummy error
During probe the driver allocates dummy I2C devices for RTC and ADC
with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC or ADC devices, fail also the probe
for main MFD driver.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: max8998: Fix possible NULL pointer dereference on i2c_new_dummy error
During probe the driver allocates dummy I2C device for RTC with i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for
main MFD driver.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: max77686: Fix possible NULL pointer dereference on i2c_new_dummy error
During probe the driver allocates dummy I2C device for RTC with
i2c_new_dummy() but it does not check the return value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: max8997: Fix possible NULL pointer dereference on i2c_new_dummy error
During probe the driver allocates dummy I2C devices for RTC, haptic and
MUIC with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().
If i2c_new_dummy() fails for RTC, haptic or MUIC devices, fail also the
probe for main MFD driver.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Paul Gortmaker [Tue, 21 Jan 2014 21:23:01 +0000 (16:23 -0500)]
mfd: Delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Linus Walleij [Thu, 23 Jan 2014 12:43:28 +0000 (13:43 +0100)]
mfd: tc3589x: Reform device tree probing
This changes the following mechanisms in the TC3589x device tree
probing path:
- Use the .of_match_table in struct device_driver to match the
device in the device tree.
- Add matches for the proper compatible strings "toshiba,..."
and all sub-variants, just as is done for the .id matches.
- Move over all the allocation of platform data etc to the
tc3589x_of_probe() function and follow the pattern of passing
a platform data pointer back, or an error pointer on error,
as found in the STMPE driver.
- Match the new (proper) compatible strings for the GPIO and
keypad MFD cells.
- Use of_device_is_compatible() rather than just !strcmp()
to discover which cells to instantiate.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: max14577: Add of_compatible to extcon mfd_cell
Add of_compatible ("maxim,max14577-muic") to the mfd_cell for extcon
driver. If entry with such compatible is present in the DTS, the extcon
driver will have of_node set.
This may be useful for extcon consumers and it is documented in
bindings documentation.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Linus Walleij [Wed, 29 Jan 2014 10:09:53 +0000 (11:09 +0100)]
mfd: Include all drivers in subsystem menu
It is currently not possible to select the SA1100 or Vexpress
drivers in the MFD subsystem, because the menu for the entire
subsystem ends before these options are presented.
Move the main menu closing and the endif for HAS_IOMEM to the
end of the file so these are selectable again.
Cc: stable@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: sec-core: Fix possible NULL pointer dereference when i2c_new_dummy error
During probe the sec-core driver allocates dummy I2C device for RTC with
i2c_new_dummy() but return value is not checked. In case of error
(i2c_new_device(): memory allocation failure or I2C address cannot be
used) this function returns NULL which is later used by
devm_regmap_init_i2c() or i2c_unregister_device().
If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.
Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for S2MPS14 PMIC device to the MFD sec-core driver.
The S2MPS14 is similar to S2MPS11 but it has fewer regulators, two
clocks instead of three and a little different registers layout.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: sec-irq: Use consistent S2MPS11 RTC alarm interrupt indexes
The S2MPS11 RTC has two alarms: alarm0 and alarm1 (corresponding
interrupts are named similarly). Use consistent names for interrupts to
limit possible errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: twl4030-madc: Use twl_i2c_read/write_u16 for 16 bit registers
Simplify reading and writing of 16 bit TWL registers in the
driver by using twl_i2c_read_u16 and twl_i2c_write_u16.
Signed-off-by: Sebastian Reichel <sre@debian.org> Acked-by: Jonathan Cameron <jic23@kernel.org> Tested-by: Marek Belisko <marek@goldelico.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a simple twl_i2c_read/write_u16 wrapper over
the twl_i2c_read/write, which is similar to the
twl_i2c_read/write_u8 wrapper.
Signed-off-by: Sebastian Reichel <sre@debian.org> Acked-by: Jonathan Cameron <jic23@kernel.org> Tested-by: Marek Belisko <marek@goldelico.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reported-by: Jonathan Cameron <jic23@kernel.org> Reported-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sebastian Reichel <sre@debian.org> Acked-by: Jonathan Cameron <jic23@kernel.org> Tested-by: Marek Belisko <marek@goldelico.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: twl4030-madc: Add DT support and convert to IIO framework
This converts twl4030-madc module to use the Industrial IO ADC
framework and adds device tree support.
Signed-off-by: Sebastian Reichel <sre@debian.org> Tested-by: Marek Belisko <marek@goldelico.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update twl4030-madc driver to use managed resources.
Signed-off-by: Sebastian Reichel <sre@debian.org> Acked-by: Jonathan Cameron <jic23@kernel.org> Tested-by: Marek Belisko <marek@goldelico.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>