Jacob Keller [Sat, 16 Jun 2012 23:29:00 +0000 (23:29 +0000)]
ixgbe: Fix PHC loophole allowing misconfiguration of increment register
This patch fixes a potential hole when configuring the cycle counter used to
generate the nanosecond time clock. This clock is based off of the SYSTIME
registers along with the TIMINCA registers. The TIMINCA register determines
the increment to be added to the SYSTIME registers every DMA clock tick. This
register needs to be reconfigured whenever the link-speed changes. However,
the value calculated stays the same when link is down and when link is up.
Misconfiguration can occur if the link status changes due to a reset, which
causes the TIMINCA register to be reset. This reset puts the device in an
unstable state where the SYSTIME registers stop incrementing and the PTP
protocol does not function.
The solution is to double check the TIMINCA value and always reset the value
if the register is zero. This prevents a misconfiguration bug that halts the
PHC.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sat, 16 Jun 2012 20:27:14 +0000 (20:27 +0000)]
bnx2x: fix I2C non-respondent issue
When I2C is not responding it's usually due to a previous
unexpected reset during I2C operation. We release it by
powering down and up the SFP+ module.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Thu, 14 Jun 2012 23:00:17 +0000 (23:00 +0000)]
ipv6: Prevent access to uninitialized fib_table_hash via /proc/net/ipv6_route
/proc/net/ipv6_route reflects the contents of fib_table_hash. The proc
handler is installed in ip6_route_net_init() whereas fib_table_hash is
allocated in fib6_net_init() _after_ the proc handler has been installed.
This opens up a short time frame to access fib_table_hash with its pants
down.
fib6_init() as a whole can't be moved to an earlier position as it also
registers the rtnetlink message handlers which should be registered at
the end. Therefore split it into fib6_init() which is run early and
fib6_init_late() to register the rtnetlink message handlers.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Reviewed-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 14 Jun 2012 08:34:24 +0000 (08:34 +0000)]
qlcnic: off by one in qlcnic_init_pci_info()
The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements. We
allocate it that way a few lines earlier in the function. So this test
is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 14 Jun 2012 06:42:44 +0000 (06:42 +0000)]
net: remove skb_orphan_try()
Orphaning skb in dev_hard_start_xmit() makes bonding behavior
unfriendly for applications sending big UDP bursts : Once packets
pass the bonding device and come to real device, they might hit a full
qdisc and be dropped. Without orphaning, the sender is automatically
throttled because sk->sk_wmemalloc reaches sk->sk_sndbuf (assuming
sk_sndbuf is not too big)
We could try to defer the orphaning adding another test in
dev_hard_start_xmit(), but all this seems of little gain,
now that BQL tends to make packets more likely to be parked
in Qdisc queues instead of NIC TX ring, in cases where performance
matters.
Reverts commits : fc6055a5ba31 net: Introduce skb_orphan_try() 87fd308cfc6b net: skb_tx_hash() fix relative to skb_orphan_try()
and removes SKBTX_DRV_NEEDS_SK_REF flag
Reported-and-bisected-by: Jean-Michel Hautbois <jhautbois@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 13 Jun 2012 09:45:16 +0000 (09:45 +0000)]
bnx2x: fix panic when TX ring is full
There is a off by one error in the minimal number of BD in
bnx2x_start_xmit() and bnx2x_tx_int() before stopping/resuming tx queue.
A full size GSO packet, with data included in skb->head really needs
(MAX_SKB_FRAGS + 4) BDs, because of bnx2x_tx_split()
This error triggers if BQL is disabled and heavy TCP transmit traffic
occurs.
bnx2x_tx_split() definitely can be called, remove a wrong comment.
Reported-by: Tomas Hruby <thruby@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eilon Greenstein <eilong@broadcom.com> Cc: Yaniv Rosner <yanivr@broadcom.com> Cc: Merav Sicron <meravs@broadcom.com> Cc: Tom Herbert <therbert@google.com> Cc: Robert Evans <evansr@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 15 Jun 2012 00:20:44 +0000 (00:20 +0000)]
can: c_can: precedence error in c_can_chip_config()
(CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK) is (0x02 & 0x01) which
is zero so the condition is never true. The intent here was to test
that both flags were set.
Cc: <stable@kernel.org> # 2.6.39+ Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 14 Jun 2012 12:43:32 +0000 (15:43 +0300)]
Merge tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- section markup fixes
- clk_prepare() fix to conform to the clk API
- memory leaks
- incorrect debug messages
- bad errorpaths
- typos
* tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinctrl-mxs: set platform driver data to NULL at errpath and at unregister
pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails
pinctrl: pinctrl-imx: fix incorrect debug message of maps
pinctrl: pinctrl-imx: free if of_get_parent fails to get the parent node
pinctrl: pinctrl-imx: free allocated pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP
pinctrl: nomadik: fix up typo
pinctrl: nomadik: add clk_prepare() call
pinctrl: fix a minor harmless typo
pinctrl: sirf: mark of_device_id match table as __devinitconst
Linus Torvalds [Thu, 14 Jun 2012 12:38:48 +0000 (15:38 +0300)]
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make
it into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't forget to call init verbs added by fixup list
ALSA: HDA: Pin fixup for Zotac Z68 motherboard
ALSA: compress_core: cleanup pointers on stop
ALSA: compress_core: don't wake up on pause
ALSA: hda - Fix detection of Creative SoundCore3D controllers
vga_switcheroo: Enable/disable audio clients at the right time
ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO
ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
vga_switcheroo: Add a helper function to get the client state
ALSA: usb-audio: Fix substream assignments
ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub
ASoC: wm2000: Always use a 4s timeout for the firmware
ASoC: dapm: Fix input list to use source widgets
ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE
ASoC: wm8994: Apply volume updates with clocks enabled
ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants
ASoC: imx-audmux: add pinctrl support
ASoC: dapm: Fix connected widget capture path query.
This has the fix for the wireless issues I ran into the other week as
well as:
1) Fix CAN c_can driver transmit handling resulting in BUG check
triggers, from AnilKumar Ch.
2) Fix packet drop monitor sleeping in atomic context, from Eric
Dumazet.
3) Fix mv643xx_eth driver build regression, from Andrew Lunn.
4) Inetpeer freeing needs an RCU grace period in order to avoid races
during tree invalidation. From Eric Dumazet.
5) Fix endianness bugs in xt_HMARK netfilter module, from Hans
Schillstrom.
6) Add proper module refcounting to l2tp_eth to avoid crash on module
unload, from Eric Dumazet.
7) Fix truncation of neighbour entry dumps due to logic errors in
neigh_dump_info() and friends, from Eric Dumazet.
8) The conversion of fib6_age() to dst_neigh_lookup() accidently
reversed the logic of a flags test, fix from Thomas Graf.
9) Fix checksum configuration in newer sky2 chips, from Stephen
Hemminger.
10) Revert BQL support in NIU driver, doesn't work.
11) l2tp_ip_sendmsg() illegally uses a route without a proper reference.
From Eric Dumazet.
12) be2net driver references an SKB after it's potentially been freed,
also from Eric Dumazet.
13) Fix RCU stalls in dummy net driver init. Also from Eric Dumazet.
14) lpc_eth has several bugs in it's transmit engine leading to packet
leaks and improper queue wakes, from Eric Dumazet.
15) Apply short DMA workaround to more tg3 chips, from Matt Carlson.
16) Add tilegx network driver.
17) Bonding queue mapping for a packet can get corrupted, fix from Eric
Dumazet.
18) Fix bug in netpoll_send_udp() SKB management that can leave garbage
in the payload in certain situations. From Eric Dumazet.
19) bnx2x driver interprets chip RX checksum offload incorrectly in
encapsulation situations. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
bnx2x: fix checksum validation
netpoll: fix netpoll_send_udp() bugs
bonding: Fix corrupted queue_mapping
bonding:record primary when modify it via sysfs
tilegx network driver: initial support
tg3: Apply short DMA frag workaround to 5906
net: stmmac: Fix clock en-/disable calls
lpc_eth: fix tx completion
lpc_eth: add missing ndo_change_mtu()
dummy: fix rcu_sched self-detected stalls
net: Reorder initialization in ip_route_output to fix gcc warning
virtio-net: fix a race on 32bit arches
r8169: avoid NAPI scheduling delay.
net: Make linux/tcp.h C++ friendly (trivial)
netdev: fix drivers/net/phy/ kernel-doc warnings
net/core: fix kernel-doc warnings
be2net: fix a race in be_xmit()
l2tp: fix a race in l2tp_ip_sendmsg()
mac80211: add back channel change flag
NFC: Fix possible NULL ptr deref when getting the name of a socket
...
Eric Dumazet [Tue, 12 Jun 2012 23:50:04 +0000 (23:50 +0000)]
bnx2x: fix checksum validation
bnx2x driver incorrectly sets ip_summed to CHECKSUM_UNNECESSARY on
encapsulated segments. TCP stack happily accepts frames with bad
checksums, if they are inside a GRE or IPIP encapsulation.
Our understanding is that if no IP or L4 csum validation was done by the
hardware, we should leave ip_summed as is (CHECKSUM_NONE), since
hardware doesn't provide CHECKSUM_COMPLETE support in its cqe.
Then, if IP/L4 checksumming was done by the hardware, set
CHECKSUM_UNNECESSARY if no error was flagged.
Patch based on findings and analysis from Robert Evans
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eilon Greenstein <eilong@broadcom.com> Cc: Yaniv Rosner <yanivr@broadcom.com> Cc: Merav Sicron <meravs@broadcom.com> Cc: Tom Herbert <therbert@google.com> Cc: Robert Evans <evansr@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 12 Jun 2012 19:30:21 +0000 (19:30 +0000)]
netpoll: fix netpoll_send_udp() bugs
Bogdan Hamciuc diagnosed and fixed following bug in netpoll_send_udp() :
"skb->len += len;" instead of "skb_put(skb, len);"
Meaning that _if_ a network driver needs to call skb_realloc_headroom(),
only packet headers would be copied, leaving garbage in the payload.
However the skb_realloc_headroom() must be avoided as much as possible
since it requires memory and netpoll tries hard to work even if memory
is exhausted (using a pool of preallocated skbs)
It appears netpoll_send_udp() reserved 16 bytes for the ethernet header,
which happens to work for typicall drivers but not all.
Right thing is to use LL_RESERVED_SPACE(dev)
(And also add dev->needed_tailroom of tailroom)
This patch combines both fixes.
Many thanks to Bogdan for raising this issue.
Reported-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Neil Horman <nhorman@tuxdriver.com> Reviewed-by: Neil Horman <nhorman@tuxdriver.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 13 Jun 2012 20:19:34 +0000 (23:19 +0300)]
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Kill off additional asm-generic wrappers.
sh: Setup CROSS_COMPILE at the top
sh: Fix up link time defsym warnings.
sh: use the new generic strnlen_user() function
sh: switch to generic strncpy_from_user().
sh: Kill off last dead UBC header
serial: sh-sci: Make probe fail for ports that exceed the maximum count
serial: sh-sci: Fix probe error paths
clocksource: sh_tmu: Use clockevents_config_and_register().
clocksource: sh_tmu: Convert timer lock to raw spinlock.
clocksource: sh_mtu2: Convert timer lock to raw spinlock.
clocksource: sh_cmt: Convert timer lock to raw spinlock.
bug.h: need linux/kernel.h for TAINT_WARN.
sh: convert to kbuild asm-generic support.
sh64: Fix up fallout from generic init_task conversion.
sh: arch/sh/kernel/process.c needs asm/fpu.h for unlazy_fpu().
Linus Torvalds [Wed, 13 Jun 2012 20:18:41 +0000 (23:18 +0300)]
Merge branch 'fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull led fixes from Bryan Wu.
* 'fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Make LEDS_ASIC3 and LEDS_RENESAS_TPU depend on LEDS_CLASS=y
leds: fixed a coding style issue.
leds: don't disable blinking when writing the same value to delay_on or delay_off
Linus Torvalds [Wed, 13 Jun 2012 20:17:12 +0000 (23:17 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k update from Geert Uytterhoeven.
This makes m68k use the generic library functions for the user-space
strn[cpy|len] functions.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Use generic strncpy_from_user(), strlen_user(), and strnlen_user()
Linus Torvalds [Wed, 13 Jun 2012 14:57:30 +0000 (17:57 +0300)]
Merge tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss build problem fix from Tomi Valkeinen:
"Small fixes for omapdss driver. Most importantly, fixes a build
problem when debugfs or omapdss debug support is turned off, and fixes
a suspend related crash."
This has apparently been annoying rmk for a while..
* tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: fix registration of DPI and SDI devices
OMAPDSS: DSI: Fix bug when calculating LP command interleaving parameters
OMAPDSS: fix bogus WARN_ON in dss_runtime_put()
OMAPDSS: Taal: fix compilation warning
OMAPDSS: fix build when DEBUG_FS or DSS_DEBUG_SUPPORT disabled
CROSS_COMPILE must be setup before using e.g. cc-option (and a few other
as-*, cc-*, ld-* macros), else they will check against the wrong compiler
when cross-compiling, and may invoke the cross compiler with wrong or
suboptimal compiler options.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: linux-sh@vger.kernel.org Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Fri, 25 May 2012 04:02:48 +0000 (13:02 +0900)]
sh: switch to generic strncpy_from_user().
This kills off the special sh32/64 versions and adopts the generic
version. It should be possible to optimize this for SH-4A unaligned
loads, but this is a corner case that can be supported incrementally.
Paul Bolle [Fri, 8 Jun 2012 20:49:17 +0000 (22:49 +0200)]
sh: Kill off last dead UBC header
Commit 7025bec9125b0a02edcaf22c2dce753bf2c95480 ("sh: Kill off dead UBC
headers.") skipped arch/sh/include/cpu-sh2a/cpu/ubc.h. Since nothing is
using that header either, kill it off too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Laurent Pinchart [Tue, 12 Jun 2012 22:28:24 +0000 (00:28 +0200)]
serial: sh-sci: Make probe fail for ports that exceed the maximum count
The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.
This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Eric Dumazet [Tue, 12 Jun 2012 06:03:51 +0000 (06:03 +0000)]
bonding: Fix corrupted queue_mapping
In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping. This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.
When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit. In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.
Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping. In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.
If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)
This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :
netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.
Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.
Based on a previous patch from Tom Herbert.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Tom Herbert <therbert@google.com> Cc: John Fastabend <john.r.fastabend@intel.com> Cc: Roland Dreier <roland@kernel.org> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Weiping Pan [Sun, 10 Jun 2012 23:00:20 +0000 (23:00 +0000)]
bonding:record primary when modify it via sysfs
If we modify primary via sysfs and it is not a valid slave,
we should record it for future use, and this behavior is the same with
bond_check_params().
Signed-off-by: Weiping Pan <wpan@redhat.com> Acked-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pin 0x1b was connected to the front panel connector, which according to
the HDA standard should contain a mic and a headphone. In this case,
the headphone was listed as "line out" by BIOS.
Linus Torvalds [Tue, 12 Jun 2012 15:48:17 +0000 (18:48 +0300)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"As per your -rc2 announce, this is small and urgent only,
The radeon one is for a regression in 3.4 so we need this one in your
tree so we can send the stable one out, code in 3.4 broke some old
userspaces. The max props increase fixes spew being seen on a few
machines. And a ttm regression to fix some accounting issues that
affect vmwgfx."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: Fix buffer object metadata accounting regression v2
drm: increase DRM_OBJECT_MAX_PROPERTY to 24
drm/radeon: fix tiling and command stream checking on evergreen v3
A regression was introduced in the 3.3 rc series, commit
"drm/ttm: simplify memory accounting for ttm user v2",
causing the metadata of buffer objects created using the ttm_bo_create()
function to be accounted twice.
That causes massive leaks with the vmwgfx driver running for example
SpecViewperf Catia-03 test 2, eventually killing the app.
Furthermore, the same commit introduces a regression where
metadata accounting is leaked if a buffer object is
initialized with an illegal size. This is also fixed with this commit.
v2: Fixed an error path and removed an unused variable.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Paulo Zanoni [Tue, 12 Jun 2012 14:27:01 +0000 (11:27 -0300)]
drm: increase DRM_OBJECT_MAX_PROPERTY to 24
Before Kernel 3.5, no one was checking for the return value of
drm_connector_attach_property, so we never noticed that we were unable
to create some properties. Commit "drm: WARN() when
drm_connector_attach_property fails" added a WARN when we fail to
create a property, and the transition from "connector properties" to
"object properties" changed the warning message a little bit.
On i915 machines with many TV connectors we hit the maximum number of
properties (since each TV connector uses a lot of properties), so we
get a few backtraces in our logs. This commit increases the maximum
number of properties to 24 hoping we'll have enough room for
everybody.
Chris suggested that we convert this code to "lists", but I believe
this conversion can come after we make sure people's dmesgs are not
spammed by our driver.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reported-by: Dave Jones <davej@redhat.com> Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dong Aisheng [Fri, 8 Jun 2012 13:33:12 +0000 (21:33 +0800)]
pinctrl: pinctrl-imx: fix incorrect debug message of maps
After create config map, the new_map pointer becomes point to
PIN_MAP_TYPE_CONFIGS_PIN map rather than PIN_MAP_TYPE_MUX_GROUP map any more.
Thus using new_map pointer to display the MUX_GROUP info is not correct.
Using map pointer instead to show the correct MUX_GROUP map info.
Original the debug message is:
imx6q-pinctrl 20e0000.iomuxc: maps: function Yp group MX6Q_PAD_SD3_CMD num 12
After fix it is:
imx6q-pinctrl 20e0000.iomuxc: maps: function usdhc3 group usdhc3grp-1 num 11
Devendra Naga [Fri, 8 Jun 2012 19:22:11 +0000 (00:52 +0530)]
pinctrl: pinctrl-imx: free allocated pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP
a) as we allocate the pinctrl_map structure at imx_dt_node_to_map at line 167, anyway
if its an element, or a num_elements * (sizeof(type)) elements allocated to one single
pointer must be freed only once.
CASE. A)
as new_map is not moved and allocated like,
for (i = 0; i < MAX_ELEMS; i++) {
new_map[i] = kmalloc(numelems * size, GFP_KERNEL);
}
its freed as
for (i = 0; i < MAX_ELEMS; i++) {
kfree(new_map[i]);
}
CASE. B)
and its allocated like
new_map = kmalloc(numelems * size, GFP_KERNEL);
it just needs kfree not as case A's.
b) use KERN_DEBUG facility for the IMX_PMX_DUMP macro.
Linus Walleij [Tue, 12 Jun 2012 10:43:06 +0000 (12:43 +0200)]
pinctrl: nomadik: fix up typo
Commit a60b57eddaa8af6c02cf7bbeb58ebf82881f08ac
"drivers/gpio: gpio-nomadik: Add support for irqdomains"
changed GPIO offset calculations to have this form:
(gpio % NMK_GPIO_PER_CHIP) except in this one place for
setting sleep mode, where the conversion was all wrong, and
instead mod:ing the GPIO with the IRQ base which does not
make any sense.
So fix this up so we can use sleepmode.
Reviewed-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Linus Torvalds [Tue, 12 Jun 2012 04:39:58 +0000 (07:39 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu from Greg Ungerer:
"This contains five fixes. Four fix build problems introduced by
recent clean up and merging of the m68k timer and ptrace code. The
other fixes the 528x ColdFire CPU QSPI base address definition, missed
in the ColdFire QSPI cleanup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: make syscall_trace_enter/leave exist for non-MMU classic m68k types
m68knommu: fix 68360 local setting of timer interrupt handler
m68knommu: fix 68328 local setting of timer interrupt handler
m68k: fix inclusion of arch_gettimeoffset for non-MMU 68k classic CPU types
m68knommu: m528x qspi definition fix
Axel Lin [Fri, 8 Jun 2012 23:41:42 +0000 (07:41 +0800)]
leds: Make LEDS_ASIC3 and LEDS_RENESAS_TPU depend on LEDS_CLASS=y
Otherwise, I got below build error when CONFIG_LEDS_CLASS=m.
LD init/built-in.o
drivers/built-in.o: In function `asic3_led_probe':
clkdev.c:(.devinit.text+0x4680): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `r_tpu_probe':
clkdev.c:(.devinit.text+0x4838): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `asic3_led_remove':
clkdev.c:(.devexit.text+0x564): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `r_tpu_remove':
clkdev.c:(.devexit.text+0x5a0): undefined reference to `led_classdev_unregister'
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Rafal Prylowski [Mon, 28 May 2012 15:35:54 +0000 (23:35 +0800)]
leds: don't disable blinking when writing the same value to delay_on or delay_off
Function led_set_software_blink() assumes that blink timer is still running,
but commit 488bc35bf40df89d37486c1826b178a2fba36ce7 introduced disabling
of blink timer before each call to led_set_software_blink().
Correct led_software_blink():
1) remove protection against reprogramming blink timer to the same values,
because it only disables blinking now,
2) remove unnecessary call to led_stop_software_blink().
Greg Ungerer [Wed, 23 May 2012 03:43:52 +0000 (13:43 +1000)]
m68k: make syscall_trace_enter/leave exist for non-MMU classic m68k types
The assembler entry code calls directly to the syscall_trace_enter() and
syscall_trace_leave() functions. But currently they are conditionaly
compiled out for the non-MMU classic m68k CPU types (so 68328 for example),
resulting in a link error:
LD vmlinux
arch/m68k/platform/68328/built-in.o: In function `do_trace':
(.text+0x1c): undefined reference to `syscall_trace_enter'
arch/m68k/platform/68328/built-in.o: In function `do_trace':
(.text+0x4c): undefined reference to `syscall_trace_leave'
Change the conditional check that includes these functions to be true for
the !defined(CONFIG_MMU) case as well.
Greg Ungerer [Wed, 23 May 2012 03:32:55 +0000 (13:32 +1000)]
m68knommu: fix 68360 local setting of timer interrupt handler
Compiling for 68360 based targets fails with:
arch/m68k/platform/68360/config.c: In function ‘hw_tick’:
arch/m68k/platform/68360/config.c:55:2: error: implicit declaration of function ‘arch_timer_interrupt’
arch/m68k/platform/68360/config.c: At top level:
arch/m68k/platform/68360/config.c:64:6: error: conflicting types for ‘hw_timer_init’
arch/m68k/include/asm/machdep.h:36:13: note: previous declaration of ‘hw_timer_init’ was here
Changes made to hw_timer_init() didn't get updated in the 68328 timer code.
So process and call the "handler" arg that is now passed into that
hw_timer_init() function.
Greg Ungerer [Wed, 23 May 2012 03:27:18 +0000 (13:27 +1000)]
m68knommu: fix 68328 local setting of timer interrupt handler
Compiling for 68328 based targets fails with:
arch/m68k/platform/68328/timers.c: In function ‘hw_tick’:
arch/m68k/platform/68328/timers.c:65:2: error: implicit declaration of function ‘arch_timer_interrupt’
arch/m68k/platform/68328/timers.c: At top level:
arch/m68k/platform/68328/timers.c:102:6: error: conflicting types for ‘hw_timer_init’
arch/m68k/include/asm/machdep.h:36:13: note: previous declaration of ‘hw_timer_init’ was here
Changes made to hw_timer_init() didn't get updated in the 68328 timer code.
So process and call the "handler" arg that is now passed into that
hw_timer_init() function.
Greg Ungerer [Wed, 23 May 2012 01:32:45 +0000 (11:32 +1000)]
m68k: fix inclusion of arch_gettimeoffset for non-MMU 68k classic CPU types
When building for non-MMU based classic 68k CPU types (like the 68328 for
example) you get a compilation error:
CC arch/m68k/kernel/time.o
arch/m68k/kernel/time.c:91:5: error: redefinition of ‘arch_gettimeoffset’
include/linux/time.h:145:19: note: previous definition of ‘arch_gettimeoffset’ was here
The arch_gettimeoffset() code is included when building for these CPU types,
but it shouldn't be. Those machine types do not have
CONFIG_ARCH_USES_GETTIMEOFFSET set.
The fix is simply to conditionally include the arch_gettimeoffset() code on
that same config setting that specifies its use or not.
Chris Metcalf [Thu, 7 Jun 2012 10:45:02 +0000 (10:45 +0000)]
tilegx network driver: initial support
This change adds support for the tilegx network driver based on the
GXIO IORPC support in the tilegx software stack, using the on-chip
mPIPE packet processing engine.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 7 Jun 2012 12:56:54 +0000 (12:56 +0000)]
tg3: Apply short DMA frag workaround to 5906
5906 devices also need the short DMA fragment workaround. This patch
makes the necessary change.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Tested-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Roese [Thu, 7 Jun 2012 23:21:05 +0000 (23:21 +0000)]
net: stmmac: Fix clock en-/disable calls
clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Viresh Kumar <viresh.linux@gmail.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 11 Jun 2012 07:21:36 +0000 (07:21 +0000)]
lpc_eth: fix tx completion
__lpc_handle_xmit() has two bugs :
1) It can leak skbs in case TXSTATUS_ERROR is set
2) It can wake up txqueue while no slot was freed.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Roland Stigge <stigge@antcom.de> Tested-by: Roland Stigge <stigge@antcom.de> Cc: Kevin Wells <kevin.wells@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
One way to get bigger skbs is to allow MTU changes above the 1500 limit.
Calling eth_change_mtu() in ndo_change_mtu() makes sure this cannot
happen.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Roland Stigge <stigge@antcom.de> Cc: Kevin Wells <kevin.wells@nxp.com> Acked-by: Roland Stigge <stigge@antcom.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mundt [Mon, 11 Jun 2012 08:10:16 +0000 (17:10 +0900)]
clocksource: sh_tmu: Use clockevents_config_and_register().
This switches over to the now exported clockevents_config() and
clockevents_config_and_register() helpers. This knocks off a
long-standing TMU TODO item.
Roland Dreier [Sun, 10 Jun 2012 20:05:24 +0000 (20:05 +0000)]
net: Reorder initialization in ip_route_output to fix gcc warning
If I build with W=1, for every file that includes <net/route.h>, I get the warning
include/net/route.h: In function 'ip_route_output':
include/net/route.h:135:3: warning: initialized field overwritten [-Woverride-init]
include/net/route.h:135:3: warning: (near initialization for 'fl4') [-Woverride-init]
(This is with "gcc (Debian 4.6.3-1) 4.6.3")
A fix seems pretty trivial: move the initialization of .flowi4_tos
earlier. As far as I can tell, this has no effect on code generation.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mundt [Mon, 11 Jun 2012 05:29:58 +0000 (14:29 +0900)]
bug.h: need linux/kernel.h for TAINT_WARN.
asm-generic/bug.h uses taint flags that are only defined in
linux/kernel.h, resulting in build failures on platforms that
don't include linux/kernel.h some other way:
arch/sh/include/asm/thread_info.h:172:2: error: 'TAINT_WARN' undeclared (first use in this function)
Caused by commit edd63a2763bd ("set_restore_sigmask() is never called
without SIGPENDING (and never should be)").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds [Mon, 11 Jun 2012 03:57:43 +0000 (06:57 +0300)]
Merge tag 'regmap-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Nothing too exciting - a cleanup for debugfs in error handling and a
fix for the padding (which has only just acquired real use) and
exporting a function that's supposed to be usable by drivers."
* tag 'regmap-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Export regmap_reinit_cache()
regmap: Fix the size calculation for map->format.buf_size
regmap: clean up debugfs if regmap_init fails
Linus Torvalds [Mon, 11 Jun 2012 03:53:48 +0000 (06:53 +0300)]
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small fixes, plus larger fixes for the gpio-regulator
driver the most recent changes for which had apparently not been
tested at all in -next (or elsewhere from the looks of it)."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Properly handle the case min_uV < rdev->desc->min_uV in map_voltage_linear
regulator: max8649: fix missing regmap in rdev
regulator: gpio-regulator: populate selector from set_voltage
regulator: gpio-regulator: Fix finding of smallest value
regulator: gpio-regulator: do not pass drvdata pointer as reference
regulator: anatop: Use correct __devexit_p annotation
regulator: palmas: Fix wrong kfree calls
Eric Dumazet [Tue, 5 Jun 2012 22:35:24 +0000 (22:35 +0000)]
virtio-net: fix a race on 32bit arches
commit 3fa2a1df909 (virtio-net: per cpu 64 bit stats (v2)) added a race
on 32bit arches.
We must use separate syncp for rx and tx path as they can be run at the
same time on different cpus. Thus one sequence increment can be lost and
readers spin forever.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Sat, 9 Jun 2012 10:53:16 +0000 (10:53 +0000)]
r8169: avoid NAPI scheduling delay.
While reworking the r8169 driver a few months ago to perform the
smallest amount of work in the irq handler, I took care of avoiding
any irq mask register operation in the slow work dedicated user
context thread. The slow work thread scheduled an extra round of NAPI
work which would ultimately set the irq mask register as required,
thus keeping such irq mask operations in the NAPI handler.
It would eventually race with the irq handler and delay NAPI execution
for - assuming no further irq - a whole ksoftirqd period. Mildly a
problem for rare link changes or corner case PCI events.
The race was always lost after the last bh disabling lock had been
removed from the work thread and people started wondering where those
pesky "NOHZ: local_softirq_pending 08" messages came from.
Actually the irq mask register _can_ be set up directly in the slow
work thread.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Reported-by: Dave Jones <davej@redhat.com> Tested-by: Marc Dionne <marc.c.dionne@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jerome Glisse [Sat, 9 Jun 2012 14:57:41 +0000 (10:57 -0400)]
drm/radeon: fix tiling and command stream checking on evergreen v3
Fix regresson since the introduction of command stream checking on
evergreen (thread referenced below). Issue is cause by ddx allocating
bo with formula width*height*bpp while programming the GPU command
stream with ALIGN(height, 8). In some case (where page alignment does
not hide the extra size bo should be according to height alignment)
the kernel will reject the command stream.
This patch reprogram the command stream to slice - 1 (slice is
a derivative value from height) which avoid rejecting the command
stream while keeping the value of command stream checking from a
security point of view.
This patch also fix wrong computation of layer size for 2D tiled
surface. Which should fix issue when 2D color tiling is enabled.
This dump the radeon KMS_DRIVER_MINOR so userspace can know if
they are on a fixed kernel or not.
Paul Pluzhnikov [Sat, 9 Jun 2012 14:53:03 +0000 (07:53 -0700)]
net: Make linux/tcp.h C++ friendly (trivial)
I originally sent this patch to <trivial@kernel.org>, but Jiri Kosina did
not feel that this is fully appropriate for the trivial tree.
Using linux/tcp.h from C++ results in:
cat t.cc
#include <linux/tcp.h>
int main() { }
g++ -c t.cc
In file included from t.cc:1:
/usr/include/linux/tcp.h:72: error: '__u32 __fswab32(__u32)' cannot appear in a constant-expression
/usr/include/linux/tcp.h:72: error: a function call cannot appear in a constant-expression
...
Attached trivial patch fixes this problem.
Tested:
- the t.cc above compiles with g++ and
- the following program generates the same output before/after
the patch:
#include <linux/tcp.h>
#include <stdio.h>
int main ()
{
#define P(a) printf("%s: %08x\n", #a, (int)a)
P(TCP_FLAG_CWR);
P(TCP_FLAG_ECE);
P(TCP_FLAG_URG);
P(TCP_FLAG_ACK);
P(TCP_FLAG_PSH);
P(TCP_FLAG_RST);
P(TCP_FLAG_SYN);
P(TCP_FLAG_FIN);
P(TCP_RESERVED_BITS);
P(TCP_DATA_OFFSET);
#undef P
return 0;
}
Signed-off-by: Paul Pluzhnikov <ppluzhnikov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Sat, 9 Jun 2012 06:46:42 +0000 (08:46 +0200)]
vga_switcheroo: Enable/disable audio clients at the right time
The audio clients have to be disabled before disabling the VGA and
switching. Similarly, enabling the audio client should be done at
last. Otherwise the audio-side operation stalls, eventually leading
to Oops or lockups.
Randy Dunlap [Fri, 8 Jun 2012 14:07:19 +0000 (14:07 +0000)]
netdev: fix drivers/net/phy/ kernel-doc warnings
Fix kernel-doc warnings in drivers/net/phy:
Warning(drivers/net/phy/mdio_bus.c:109): No description found for parameter 'mdio_bus_np'
Warning(drivers/net/phy/mdio_bus.c:109): Excess function parameter 'mdio_np' description in 'of_mdio_find_bus'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Fri, 8 Jun 2012 14:01:44 +0000 (14:01 +0000)]
net/core: fix kernel-doc warnings
Fix kernel-doc warnings in net/core:
Warning(net/core/skbuff.c:3368): No description found for parameter 'delta_truesize'
Warning(net/core/filter.c:628): No description found for parameter 'pfp'
Warning(net/core/filter.c:628): Excess function parameter 'sk' description in 'sk_unattached_filter_create'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Kara [Fri, 8 Jun 2012 15:07:36 +0000 (17:07 +0200)]
writeback: Fix lock imbalance in writeback_sb_inodes()
Fix bug introduced by 169ebd90. We have to have wb_list_lock locked when
restarting writeback loop after having waited for inode writeback.
Bug description by Ted Tso:
I can reproduce this fairly easily by using ext4 w/o a journal, running
under KVM with 1024megs memory, with fsstress (xfstests #13):
[ 45.153294] =====================================
[ 45.154784] [ BUG: bad unlock balance detected! ]
[ 45.155591] 3.5.0-rc1-00002-gb22b1f1 #124 Not tainted
[ 45.155591] -------------------------------------
[ 45.155591] flush-254:16/2499 is trying to release lock (&(&wb->list_lock)->rlock) at:
[ 45.155591] [<c022c3da>] writeback_sb_inodes+0x160/0x327
[ 45.155591] but there are no more locks to release!
Reported-by: Theodore Ts'o <tytso@mit.edu> Tested-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
David Rientjes [Fri, 8 Jun 2012 20:21:26 +0000 (13:21 -0700)]
mm, oom: fix badness score underflow
If the privileges given to root threads (3% of allowable memory) or a
negative value of /proc/pid/oom_score_adj happen to exceed the amount of
rss of a thread, its badness score overflows as a result of commit a7f638f999ff ("mm, oom: normalize oom scores to oom_score_adj scale only
for userspace").
Fix this by making the type signed and return 1, meaning the thread is
still eligible for kill, if the value is negative.
Reported-by: Dave Jones <davej@redhat.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 8 Jun 2012 20:18:33 +0000 (13:18 -0700)]
sched/fair: fix lots of kernel-doc warnings
Fix lots of new kernel-doc warnings in kernel/sched/fair.c:
Warning(kernel/sched/fair.c:3625): No description found for parameter 'env'
Warning(kernel/sched/fair.c:3625): Excess function parameter 'sd' description in 'update_sg_lb_stats'
Warning(kernel/sched/fair.c:3735): No description found for parameter 'env'
Warning(kernel/sched/fair.c:3735): Excess function parameter 'sd' description in 'update_sd_pick_busiest'
Warning(kernel/sched/fair.c:3735): Excess function parameter 'this_cpu' description in 'update_sd_pick_busiest'
.. more warnings
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It incorrectly finds VGA connectors where none are attached, apparently
not noticing that nothing replied to the EDID queries, and happily using
the default EDID modes that have nothing to do with actual hardware.
That in turn then causes X to fall down to the lowest common
denominator, which is usually the default 1024x768 mode that is in the
default EDID and pretty much anything supports).
I'd suggest that if not relying on the HDP pin, the code should at least
check whether it gets valid EDID data back, rather than just assume
there's something on the VGA connector.
Cc: Dave Airlie <airlied@linux.ie> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Fri, 8 Jun 2012 06:25:00 +0000 (06:25 +0000)]
l2tp: fix a race in l2tp_ip_sendmsg()
Commit 081b1b1bb27f (l2tp: fix l2tp_ip_sendmsg() route handling) added
a race, in case IP route cache is disabled.
In this case, we should not do the dst_release(&rt->dst), since it'll
free the dst immediately, instead of waiting a RCU grace period.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: James Chapman <jchapman@katalix.com> Cc: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 8 Jun 2012 18:15:31 +0000 (11:15 -0700)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Theodore Ts'o:
"This update contains two bug fixes, both destined for the stable tree.
Perhaps the most important is one which fixes ext4 when used with file
systems originally formatted for use with ext3, but then later
converted to take advantage of ext4."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: don't set i_flags in EXT4_IOC_SETFLAGS
ext4: fix the free blocks calculation for ext3 file systems w/ uninit_bg
Linus Torvalds [Fri, 8 Jun 2012 18:06:01 +0000 (11:06 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
Pull powerpc fixes from Paul Mackerras:
"Two small fixes for powerpc:
- a fix for a regression since 3.2 that causes 4-second (or longer)
pauses
- a fix for a potential oops when loading kernel modules on 32-bit
embedded systems."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix kernel panic during kernel module load
powerpc/time: Sanity check of decrementer expiration is necessary
Linus Torvalds [Fri, 8 Jun 2012 18:04:06 +0000 (11:04 -0700)]
Merge tag 'upstream-3.5-rc2' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS fixes from Artem Bityutskiy:
"Fix UBI and UBIFS - they refuse to work without debugfs. This was
broken by the 3.5-rc1 UBI/UBIFS changes when we removed the debugging
Kconfig switches.
Also, correct locking in 'ubi_wl_flush()' - it was extended to support
flushing a specific LEB in 3.5-rc1, and the locking was sub-optimal."
* tag 'upstream-3.5-rc2' of git://git.infradead.org/linux-ubifs:
UBI: correct ubi_wl_flush locking
UBIFS: fix debugfs-less systems support
UBI: fix debugfs-less systems support
removed IEEE80211_CONF_CHANGE_CHANNEL argument from ieee80211_hw_config,
which is required by iwl4965 driver, otherwise that driver does not
configure channel properly and is not able to associate.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sasha Levin [Wed, 6 Jun 2012 21:02:55 +0000 (23:02 +0200)]
NFC: Fix possible NULL ptr deref when getting the name of a socket
llcp_sock_getname() might get called before the LLCP socket was created.
This condition isn't checked, and llcp_sock_getname will simply deref a
NULL ptr in that case.
This exists starting with d646960 ("NFC: Initial LLCP support").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: disable the buggy chain extension feature in HW
This feature has been reported to be buggy and enabled by
default. We therefore need to disable it manually.
Cc: stable@vger.kernel.org Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: don't mess up the SCD when removing a key
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Cc: stable@vger.kernel.org [2.6.27+] Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Tue, 5 Jun 2012 18:58:20 +0000 (20:58 +0200)]
bcma: fix null pointer in bcma_core_pci_irq_ctl
pc could be null if hosttype != BCMA_HOSTTYPE_PCI.
If we are on a device without a pci core this function is called with
pc = null by b43 and brcmsmac. If the host type is PCI we have a pci
core as well and pc can not be null.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log