Enable the SD-Card interface on multiple Option 3G sticks.
The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an interface
driver.
Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add FTDI device IDs for several ELV devices and NXTCam of Lego Mindstorms NXT
- add hopefully helpful new_id comment
- remove less helpful "Due to many user requests for multiple ELV devices we enable
them by default." comment (we simply add _all_ known devices - an
enduser shouldn't have to fiddle with obscure module parameters...).
- add myself to DRIVER_AUTHOR
The missing NXTCam ID has been found at
http://www.unixboard.de/vb3/showthread.php?t=44155
, ELV devices taken from ELV Windows .inf file.
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c
AD4USB measuring converter is a 4-input A/D converter which enables the
user to measure to four current inputs ranging from 0(4) to 20 mA or
voltage between 0 and 10 V. The measured values are then transferred to
a superior system in digital form. The AD4USB communicates via USB.
Powered is also via USB. datasheet in english is here:
http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdf
This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).
Compile-tested, based on latest mainline git.
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. Open a USB device through devio.
2. Remove the hcd module in the host kernel.
3. Close the devio file descriptor.
The problem is that closing the file descriptor does usb_release_dev
as it is the last reference. usb_release_dev then tries to invoke
the hcd free_dev function (or rather dereferencing the hcd driver
struct). This causes an oops as the hcd driver has already been
unloaded so the struct is gone.
This patch tries to fix this by bringing the free_dev call earlier
and into usb_disconnect. I have verified that repeating the
above steps no longer crashes with this patch applied.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When hardware is removed on a Stratus, the system may crash like this:
ACPI: PCI interrupt for device 0000:7c:00.1 disabled
Trying to free nonexistent resource <00000000a8000000-00000000afffffff>
Trying to free nonexistent resource <00000000a4800000-00000000a480ffff>
uhci_hcd 0000:7e:1d.0: remove, state 1
usb usb2: USB disconnect, address 1
usb 2-1: USB disconnect, address 2
Unable to handle kernel paging request at 0000000000100100 RIP:
[<ffffffff88021950>] :uhci_hcd:uhci_scan_schedule+0xa2/0x89c
This occurs because an interrupt scans uhci->skelqh, which is
being freed. We do the right thing: disable the interrupts in the
device, and do not do any processing if the interrupt is shared
with other source, but it's possible that another CPU gets
delayed somewhere (e.g. loops) until we started freeing.
The agreed-upon solution is to wait for interrupts to play out
before proceeding. No other bareers are neceesary.
A backport of this patch was tested on a 2.6.18 based kernel.
Testing of 2.6.32-based kernels is under way, but it takes us
forever (months) to turn this around. So I think it's a good
patch and we should keep it.
Tracked in RH bz#516851
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According "5.3.6 Capability Parameters (HCCPARAMS)" of xHCI rev0.96 spec,
value of xECP register indicates a relative offset, in 32-bit words,
from Base to the beginning of the first extended capability.
The wrong calculation will cause BIOS handoff fail (not handoff from BIOS)
in some platform with BIOS USB legacy sup support.
Signed-off-by: Edward Shao <laface.tw@gmail.com> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Renninger <trenn@suse.de> reported on IBM x3330
booting a latest kernel on this machine results in:
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0
ACPI: SCI (IRQ30) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20090903/evevent-161)
ACPI: Unable to start the ACPI Interpreter
x86/pci: update pirq_enable_irq() to setup io apic routing
it turns out we need to set irq routing for the sci on ioapic1 early.
-v2: make it work without sparseirq too.
-v3: fix checkpatch.pl warning, and cc to stable
Reported-by: Thomas Renninger <trenn@suse.de> Bisected-by: Thomas Renninger <trenn@suse.de> Tested-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-2-git-send-email-yinghai@kernel.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When two drivers are setting up MSI-X at the same time via
pci_enable_msix() there is a race. See this dmesg excerpt:
[ 85.170610] ixgbe 0000:02:00.1: irq 97 for MSI/MSI-X
[ 85.170611] alloc irq_desc for 99 on node -1
[ 85.170613] igb 0000:08:00.1: irq 98 for MSI/MSI-X
[ 85.170614] alloc kstat_irqs on node -1
[ 85.170616] alloc irq_2_iommu on node -1
[ 85.170617] alloc irq_desc for 100 on node -1
[ 85.170619] alloc kstat_irqs on node -1
[ 85.170621] alloc irq_2_iommu on node -1
[ 85.170625] ixgbe 0000:02:00.1: irq 99 for MSI/MSI-X
[ 85.170626] alloc irq_desc for 101 on node -1
[ 85.170628] igb 0000:08:00.1: irq 100 for MSI/MSI-X
[ 85.170630] alloc kstat_irqs on node -1
[ 85.170631] alloc irq_2_iommu on node -1
[ 85.170635] alloc irq_desc for 102 on node -1
[ 85.170636] alloc kstat_irqs on node -1
[ 85.170639] alloc irq_2_iommu on node -1
[ 85.170646] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000088
As you can see igb and ixgbe are both alternating on create_irq_nr()
via pci_enable_msix() in their probe function.
ixgbe: While looping through irq_desc_ptrs[] via create_irq_nr() ixgbe
choses irq_desc_ptrs[102] and exits the loop, drops vector_lock and
calls dynamic_irq_init. Then it sets irq_desc_ptrs[102]->chip_data =
NULL via dynamic_irq_init().
igb: Grabs the vector_lock now and starts looping over irq_desc_ptrs[]
via create_irq_nr(). It gets to irq_desc_ptrs[102] and does this:
cfg_new = irq_desc_ptrs[102]->chip_data;
if (cfg_new->vector != 0)
continue;
This hits the NULL deref.
Another possible race exists via pci_disable_msix() in a driver or in
the number of error paths that call free_msi_irqs():
There's a path in the pagefault code where the kernel deliberately
breaks its own locking rules by kmapping a high pte page without
holding the pagetable lock (in at least page_check_address). This
breaks Xen's ability to track the pinned/unpinned state of the
page. There does not appear to be a viable workaround for this
behaviour so simply disable HIGHPTE for all Xen guests.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
LKML-Reference: <1267204562-11844-1-git-send-email-ian.campbell@citrix.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Pasi Kärkkäinen <pasik@iki.fi> Cc: <xen-devel@lists.xensource.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not set current->mm->mmap to NULL in 32-bit emulation on 64-bit
load_aout_binary after flush_old_exec as it would destroy already
set brpm mapping with arguments.
Studying the DSDTs of various thinkpads, it looks like bit 3 of the
argument to SBDC and SWAN is not "set radio to last state on resume".
Rather, it seems to be "if this bit is set, enable radio on resume,
otherwise disable it on resume".
So, the proper way to prepare the radios for S3 suspend is: disable
radio and clear bit 3 on the SBDC/SWAN call to to resume with radio
disabled, and enable radio and set bit 3 on the SBDC/SWAN call to
resume with the radio enabled.
Also, for persistent devices, the rfkill core does not restore state,
so we really need to get the firmware to do the right thing.
We don't sync the radio state on suspend, instead we trust the BIOS to
not do anything weird if we never touched the radio state since boot.
Time will tell if that's a wise way of doing things...
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Brightness notification does not work until the user writes to
hotkey_mask attribute. That's because the polling thread will only run
if hotkey_user_mask is set and someone is reading the input device or
if hotkey_driver_mask is set. In this second case, this condition is
not tested after the mask is changed, because the brightness and
volume drivers are started after the hotkey drivers.
Fix tpacpi_hotkey_driver_mask_set() to call hotkey_poll_setup(), so
that the poller kthread will be started when needed.
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Tested-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Event 0x3006 is used to help power management of the ODD in the
UltraBay. The EC generates this event when the ODD eject button is
pressed (even if the bay is powered down).
Normally, Linux doesn't need this as we keep the SATA link powered
up (which wastes power). The EC powers up the bay by itself when the
ODD eject button is pressed, and the SATA PHY reports the hotplug.
However, we could also power that SATA link down (and for that matter,
also power down the Ultrabay) if the ODD is left idle for a while with
no disk inside, and use event 0x3006 to know when we need that SATA link
powered back up.
For now, just stop asking for more information when event 0x3006 is
seen, there is no point in pestering users about it anymore.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intergraph bought 3D Labs and some XVR-500 chips have Intergraph's
vendor id.
Reported-by: Jurij Smakov <jurij@wooyd.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
e->index overflows e->stamps[] every ip_pkt_list_tot packets.
Consider the case when ip_pkt_list_tot==1; the first packet received is stored
in e->stamps[0] and e->index is initialized to 1. The next received packet
timestamp is then stored at e->stamps[1] in recent_entry_update(),
a buffer overflow because the maximum e->stamps[] index is 0.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If b43 or b43legacy are deauthenticated or disconnected, there is a
possibility that a reconnection is tried with the queues stopped in
mac80211. To prevent this, start the queues before setting
STAT_INITIALIZED.
In b43, a similar change has been in place (twice) in the
wireless_core_init() routine. Remove the duplicate and add similar
code to b43legacy.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hardware needs to know what type of frames are being
sent in order to fill in various fields, for example the
timestamp in probe responses (before this patch, it was
always 0). Set it correctly when initializing the TX
descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While ath9k does not support RIFS yet, the ability to receive RIFS
frames is currently enabled for most chipsets in the initvals.
This is causing baseband related issues on AR9160 and AR9130 based
chipsets, which can lock up under certain conditions.
This patch fixes these issues by overriding the initvals, effectively
disabling RIFS for all affected chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When selecting the tx fallback rate, rc.c used a separate variable
'nrix' for storing the next rate index, however it did not use that as
reference for further rate index lowering. Because of that, it ended up
reusing the same rate for multiple multi-rate retry stages, thus
decreasing delivery probability under changing link conditions.
This patch removes the separate (unnecessary) variable and fixes
fallback the way it was intended to work.
This should result in increased throughput and better link stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In AP mode, ath_beacon_config_ap only restarts the timer if a TSF
restart is requested. Apparently this was added, because this function
unconditionally sets the flag for TSF reset.
The problem with this is, that ath9k_hw_reset() clobbers the timer
registers (specified in the initvals), thus effectively disabling the
SWBA interrupt whenever a card reset without TSF reset is issued
(happens in a few places in the code).
This patch fixes ath_beacon_config_ap to only issue the TSF reset flag
when necessary, but reinitialize the timer unconditionally. Tests show,
that this is enough to keep the SWBA interrupt going after a call to
ath_reset()
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We use scm_send and scm_recv on both unix domain and
netlink sockets, but only unix domain sockets support
everything required for file descriptor passing,
so error if someone attempts to pass file descriptors
over netlink sockets.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The UltraDMA Tss timing must be stretched with ATA clock of 66 MHz, but the
driver only does this when PCI clock is 66 MHz, whereas it always programs
DPLL clock (which is used as the ATA clock) to 66 MHz.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An off-by-one error caused some inputs to not be created by the driver
when they should. TMP421 gets only one input instead of two, TMP422
gets two instead of three, etc. Fix the bug by listing explicitly the
number of inputs each device has.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Andre Prendel <andre.prendel@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
wm831x_gpio_direction_output() ignored the state passed into it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds error-paths to handle pci_dma_mapping errors.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A crash has been reported with sierra driver on disconnect with
Ubuntu/Lucid distribution based on kernel-2.6.32.
The cause of the crash was determined as "NULL tty pointer was being
referenced" and the NULL pointer was passed by sierra_indat_callback().
This patch modifies sierra_indat_callback() function to check for NULL
tty structure pointer. This modification prevents a crash from happening
when the device is disconnected.
This patch fixes the bug reported in Launchpad:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/511157
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The platform code doesn't have to provide platform data to get sensible
default behaviour from the imx serial driver.
This patch does not handle NULL dereference in the IrDA case, which still
requires a valid platform data pointer (in imx_startup()/imx_shutdown()),
since I don't know whether there is a sensible default behaviour, or
should the operation just fail cleanly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Alan Cox <alan@linux.intel.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Oskar Schirmer <os@emlix.com> Cc: Fabian Godehardt <fg@emlix.com> Cc: Daniel Glöckner <dg@emlix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was noticed by Matthias Urlichs and he proposed a fix. This patch
does the fixing a different way to avoid introducing several new race
conditions into the code.
The problem case is TTY_DRIVER_RESET_TERMIOS = 0. In that case while we
abort the ldisc change, the hangup processing has not cleaned up and restarted
the ldisc either.
We can't restart the ldisc stuff in the set_ldisc as we don't know what
the hangup did and may touch stuff we shouldn't as we are no longer
supposed to influence the tty at that point in case it has been re-opened
before we get rescheduled.
Instead do it the simple way. Always re-init the ldisc on the hangup, but
use TTY_DRIVER_RESET_TERMIOS to indicate that we should force N_TTY.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before unlinking the inode, reset the current permissions of possible
references like hardlinks, so granted permissions can not be retained
across the device lifetime by creating hardlinks, in the unusual case
that there is a user-writable directory on the same filesystem.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The problem is that kobject_add_internal() first adds a kobject to the
kset and then try to create sysfs directory for it. If the creation
fails, it remove the kobject from the kset. get_device_parent()
accesses class_dirs kset while only holding class_dirs.list_lock to
see whether the cuse class dir exists. But when it exists, it may not
have finished initialization yet or may fail and get removed soon. In
the above case, the former happened so the second one ends up trying
to create subdirectory under NULL sysfs_dirent.
Fix it by grabbing a mutex in get_device_parent().
Don't touch the variable 'reg' to construct the value for the actual SPI
transport. This variable is again used to access the driver's register
cache, and so random memory is overwritten.
Compute the value in-place instead.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a patch that adds MIDI support through USB for one of the Access
Music synths, the VirusTI.
The synth uses standard USBMIDI protocol on its USB interface 3, although
it does signal "vendor specific" class. A magic string has to be sent on
interface 3 to enable the sending of MIDI from the synth (this string was
found by sniffing usb communication of the Windows driver). This is all
my patch does, and it works on my computer.
Please note that the synth can also do standard usb audio I/O on its
interfaces 2&3, which already works with the current snd-usb-audio driver,
except for the audio input from the synth. I'm going to work on it when I
have some time.
Signed-off-by: Sebastien Alaiwan <sebastien.alaiwan@gmail.com> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a headphones-only quirk for the Fujitsu Siemens D1289.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: Marc Haber <mh+alsa201002@zugschlus.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://bugs.launchpad.net/bugs/524948
The OR has verified that the existing model=laptop-eapd quirk does not
function correctly but instead needs model=3stack. Make this change
so that manual corrections to module-init-tools file(s) are not
required.
Reported-by: Lasse Havelund <lasse@havelund.org> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During switching virtual counters there is access to perfctr msrs. If
the counter is not available this fails due to an invalid
address. This patch fixes this.
Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Standard AMD systems have the same number of nodes as there are
northbridge devices. However, there may kernel configurations
(especially for 32 bit) or system setups exist, where the node number
is different or it can not be detected properly. Thus the check is not
reliable and may fail though IBS setup was fine. For this reason it is
better to remove the check.
Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Multiple virtual counters share one physical counter. The reservation
of virtual counters fails due to duplicate allocation of the same
counter. The counters are already reserved. Thus, virtual counter
reservation may removed at all. This also makes the code easier.
Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some code that is in ams_exit() (the module exit code) should instead
be called when the device (not module) is removed. It probably doesn't
make much of a difference in the PMU case, but in the I2C case it does
matter.
I make no guarantee that my fix isn't racy, I'm not familiar enough
with the ams driver code to tell for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Christian Kujau <lists@nerdbynature.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Stelian Pop <stelian@popies.net> Cc: Michael Hanselmann <linux-kernel@hansmi.ch> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looking at drivers/macintosh/therm_adt746x.c, the sysfs files are
created in thermostat_init() and removed in thermostat_exit(), which
are the driver's init and exit functions. These files are backed-up by
a per-device structure, so it looks like the wrong thing to do: the
sysfs files have a lifetime longer than the data structure that is
backing it up.
I think that sysfs files creation should be moved to the end of
probe_thermostat() and sysfs files removal should be moved to the
beginning of remove_thermostat().
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Christian Kujau <lists@nerdbynature.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Colin Leroy <colin@colino.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hibernate memory preallocation code allocates memory to push some
user space data out of physical RAM, so that the hibernation image is
not too large. It allocates more memory than necessary for creating
the image, so it has to release some pages to make room for
allocations made while suspending devices and disabling nonboot CPUs,
or the system will hang due to the lack of free pages to allocate
from. Unfortunately, the function used for freeing these pages,
free_unnecessary_pages(), contains a bug that prevents it from doing
the job on all systems without highmem.
Fix this problem, which is a regression from the 2.6.30 kernel, by
using the right condition for the termination of the loop in
free_unnecessary_pages().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
has a bug that causes endless loop when Payload Pointer of MPEG2-TS
frame is 182 or 183. Anyone who sends malicious MPEG2-TS frame will
cause the receiver of ULE SNDU to go into endless loop.
This patch was generated and tested against linux-2.6.32.9 and should
apply cleanly to linux-2.6.33 as well because there was only one typo
fix to dvb_net.c since v2.6.32.
This bug was brought to you by modern day Santa Claus who decided to
shower the satellite dish at Keio University with heavy snow causing
huge burst of errors. We, receiver end, received Santa Claus's gift in
the form of kernel bug.
Care has been taken not to introduce more bug by fixing this bug, but
please scrutinize the code for I always produces buggy code.
Signed-off-by: Ang Way Chuang <wcang79@gmail.com> Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that Mimio has a userspace solution for this product using
libusb, and the in-kernel driver is just getting in the way now and
causing problems. So they have asked that the in-kernel driver be
removed. As the staging driver wasn't quite working anyway, and Mimio
supports their libusb solution for all distros, I am removing the
in-kernel driver.
The libusb solution can be downloaded from:
http://www.mimio.com/downloads/mimio_studio_software/linux.asp
Cc: <mwilder@cs.nmsu.edu> Cc: Phil Hannent <phil@hannent.co.uk> Cc: Marc Rousseau <Marc.Rousseau@mimio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The HV core mucks around with specific irqs and other low-level stuff
and takes forever to determine that it really shouldn't be running on a
machine. So instead, trigger off of the DMI system information and
error out much sooner. This also allows the module loading tools to
recognize that this code should be loaded on this type of system.
All of the SH clocksource drivers follow the scheme that the IRQ is setup
prior to registering the clockevent. The interrupt handler in the
clockevent cases looks to the event handler function pointer being filled
in by the registration code, permitting us to get in to situations where
asserted IRQs step in to the handler before registration has had a chance
to complete and hitting a NULL pointer deref.
In practice this is not an issue for most platforms, but some of them
with fairly special loaders (or that are chain-loading from another
kernel) may enter in to this situation. This fixes up the oops reported
by Rafael on hp6xx.
Reported-and-tested-by: Rafael Ignacio Zurita <rafaelignacio.zurita@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are BUGs "scheduling while atomic" triggered by the timer
rhine_tx_timeout(). They are caused by calling napi_disable() (with
msleep()). This patch fixes it by moving most of the timer content to
the workqueue function (similarly to other drivers, like tg3), with
spin_lock() changed to BH version.
Additionally, there is spin_lock_irq() moved in rhine_close() to
exclude napi_disable() etc., also tg3's way.
Reported-by: Andrey Rahmatullin <wrar@altlinux.org> Tested-by: Andrey Rahmatullin <wrar@altlinux.org> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stall workaround doesn't work with bcm4320a devices like with bcm4320b.
This workaround actually causes more stalls/device freeze on bcm4320a.
Therefore disable stall workaround by default.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rndis_query_oid overwrites *len which stores buffer size to return full size
of received command and then uses *len with memcpy to fill buffer with
command.
Ofcourse memcpy should be done before replacing buffer size.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rndis_wlan didn't know about NL80211_AUTHTYPE_AUTOMATIC and simple
setup with 'iwconfig wlan essid no-encrypt' would fail (ENOSUPP).
v2: use NDIS_80211_AUTH_AUTO_SWITCH instead of _OPEN.
This will make device try shared key auth first, then open.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some newer Lenovo models are shipped with a TPM that doesn't seem to set the TPM_STS_DATA_EXPECT status bit
when sending it a burst of data, so the code understands it as a failure and doesn't proceed sending the chip
the intended data. In this patch we bypass this bit check in case the itpm module parameter was set.
As we removed TV hotplug, don't check its status ever.
Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Somehow the case for G33 got dropped while porting from ums code.
This made a 400MHz chip into a 133MHz one which resulted in the
unnecessary enabling of double wide pipe mode which in turn
screwed up the overlay code.
Nothing else (than the overlay code) seems to be affected.
This fixes fdo.org bug #24835
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original code incorrectly assumed only status-type-0
IOCBs would be queued to the response-queue, and thus all
entries would safely reference a VHA from the IOCB
'handle.'
This patch workaround a possible security issue which can allow
user to abuse drm on r6xx/r7xx hw to access any system ram memory.
This patch doesn't break userspace, it detect "valid" old use of
CB_COLOR[0-7]_FRAG & CB_COLOR[0-7]_TILE registers and overwritte
the address these registers are pointing to with the one of the
last color buffer. This workaround will work for old mesa &
xf86-video-ati and any old user which did use similar register
programming pattern as those (we expect that there is no others
user of those ioctl except possibly a malicious one). This patch
add a warning if it detects such usage, warning encourage people
to update their mesa & xf86-video-ati. New userspace will submit
proper relocation.
Fix for xf86-video-ati / mesa (this kernel patch is enough to
prevent abuse, fix for userspace are to set proper cs stream and
avoid kernel warning) :
http://cgit.freedesktop.org/xorg/driver/xf86-video-ati/commit/?id=95d63e408cc88b6934bec84a0b1ef94dfe8bee7b
http://cgit.freedesktop.org/mesa/mesa/commit/?id=46dc6fd3ed5ef96cda53641a97bc68c3bc104a9f
Abusing this register to perform system ram memory is not easy,
here is outline on how it could be achieve. First attacker must
have access to the drm device and be able to submit command stream
throught cs ioctl. Then attacker must build a proper command stream
for r6xx/r7xx hw which will abuse the FRAG or TILE buffer to
overwrite the GPU GART which is in VRAM. To achieve so attacker
as to setup CB_COLOR[0-7]_FRAG or CB_COLOR[0-7]_TILE to point
to the GPU GART, then it has to find a way to write predictable
value into those buffer (with little cleverness i believe this
can be done but this is an hard task). Once attacker have such
program it can overwritte GPU GART to program GPU gart to point
anywhere in system memory. It then can reusse same method as he
used to reprogram GART to overwritte the system ram through the
GART mapping. In the process the attacker has to be carefull to
not overwritte any sensitive area of the GART table, like ring
or IB gart entry as it will more then likely lead to GPU lockup.
Bottom line is that i think it's very hard to use this flaw
to get system ram access but in theory one can achieve so.
Side note: I am not aware of anyone ever using the GPU as an
attack vector, nevertheless we take great care in the opensource
driver to try to detect and forbid malicious use of GPU. I don't
think the closed source driver are as cautious as we are.
[bwh: Adjusted context for 2.6.32] Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@linux.ie> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will avoid oops if at later point the fb is use. Trying to create
a framebuffer with no valid GEM object is bogus and should be forbidden
as this patch does.
The book keeping structure for transmit always had the flags value
cleared so transmit DMA maps were never released correctly.
Based on patch by Jarek Poplawski, problem observed by Michael Breuer.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I fix a bug in ks8851_mll driver, which has existed since 2.6.32-rc6.
>From : David J. Choi <david.choi@micrel.com>
Fix a bug that the data pointers in the interrupt handler are set wrong, which is related with the 5th parameter of request_irq().
Signed-off-by: David J. Choi <david.choi@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit 0b5ccb2(title:ipv6: reassembly: use seperate reassembly queues for
conntrack and local delivery) has broken the saddr&&daddr member of
nf_ct_frag6_queue when creating new queue. And then hash value
generated by nf_hashfn() was not equal with that generated by fq_find().
So, a new received fragment can't be inserted to right queue.
The patch fixes the bug with adding member of user to nf_ct_frag6_queue structure.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently we treat IGMPv3 reports as if it were an IGMPv2/v1 report.
This is broken as IGMPv3 reports are formatted differently. So we
end up suppressing a bogus multicast group (which should be harmless
as long as the leading reserved field is zero).
In fact, IGMPv3 does not allow membership report suppression so
we should simply ignore IGMPv3 membership reports as a host.
This patch does exactly that. I kept the case statement for it
so people won't accidentally add it back thinking that we overlooked
this case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.
I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.
CC: Herbert Xu <herbert@gondor.apana.org.au> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wireless sysfs methods like the rest of the networking sysfs
methods are removed with the rtnl_lock held and block until
the existing methods stop executing. So use rtnl_trylock
and restart_syscall so that the code continues to work.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Yuck. It turns out that when we restart sysctls we were restarting
with the values already changed. Which unfortunately meant that
the second time through we thought there was no change and skipped
all kinds of work, despite the fact that there was indeed a change.
I have fixed this the simplest way possible by restoring the changed
values when we restart the sysctl write.
One of my coworkers spotted this bug when after disabling forwarding
on an interface pings were still forwarded.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TSB I-tlb load code tries to use andcc to check the _PAGE_EXEC_4U bit,
but that's bit 12 so it gets sign extended all the way up to bit 63
and the test nearly always passes as a result.
Use sethi to fix the bug.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Accidently changed the struct stat uid/gid members
to uid_t and gid_t, but those get set to
__kernel_uid32_t and __kernel_gid32_t respectively.
Those are of type 'int' but the structure is meant
to have 'short'. So use uid16_t and gid16_t to
correct this.
Reported-by: Rob Landley <rob@landley.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It doesn't account for phys_base like it should, fix by using
page_to_pfn().
While we're here, make virt_to_page() use pfn_to_page() as well, so we
consistently use the asm/memory-model.h abstractions instead of
open-coding memory model assumptions.
Tested-by: Kristoffer Glembo <kristoffer@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* pa[idp->layers] should be cleared even if it's not used by
sub_alloc() because it's used by mark idr_mark_full().
* The original condition check also assigned pa[l] to p which the new
code didn't do thus leaving p pointing at the wrong layer.
Both problems have been fixed and the idr code has received good amount
testing using userland testing setup where simple bitmap allocator is
run parallel to verify the result of idr allocation.
The bug this patch fixes is caused by sub_alloc() optimization path
bypassing out-of-room condition check and restarting allocation loop
with starting value higher than maximum allowed value. For detailed
description, please read commit message of 859ddf09.
Signed-off-by: Tejun Heo <tj@kernel.org>
Based-on-patch-from: Eric Paris <eparis@redhat.com> Reported-by: Eric Paris <eparis@redhat.com> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Serge Hallyn <serue@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch prevents call set_wep_key() with zero key length. That fix long
standing regression since commit c0380693520b1a1e4f756799a0edc379378b462a
"airo: clean up WEP key operations". Additionally print call trace when
someone will try to use improper parameters, and remove key.len = 0
assignment, because it is in not possible code path.
Reported-by: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu> Bisected-by: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu> Tested-by: Chris Siebenmann <cks@cs.toronto.edu> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices do not react to a control request (seen on APC UPS's) resulting in
a slow stream of messages, "generic-usb ... control queue full". Therefore
request needs a timeout.
Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David Fries <david@fries.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>