David S. Miller [Thu, 20 Sep 2012 20:39:59 +0000 (16:39 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
1. Extension to PPS/PTP to allow for PHC devices where pulses are
subject to a variable but measurable delay.
2. PPS/PTP/PHC support for Solarflare boards with a timestamping
peripheral.
3. MTD support for updating the timestamping peripheral on those boards.
4. Fix for potential over-length requests to firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Sun, 9 Sep 2012 13:55:26 +0000 (13:55 +0000)]
r8169: use unlimited DMA burst for TX
The r8169 driver currently limits the DMA burst for TX to 1024 bytes. I have
a box where this prevents the interface from using the gigabit line to its full
potential. This patch solves the problem by setting TX_DMA_BURST to unlimited.
The box has an ASRock B75M motherboard with on-board RTL8168evl/8111evl
(XID 0c900880). TSO is enabled.
I used netperf (TCP_STREAM test) to measure the dependency of TX throughput
on MTU. I did it for three different values of TX_DMA_BURST ('5'=512, '6'=1024,
'7'=unlimited). This chart shows the results:
http://michich.fedorapeople.org/r8169/r8169-effects-of-TX_DMA_BURST.png
Interesting points:
- With the current DMA burst limit (1024):
- at the default MTU=1500 I get only 842 Mbit/s.
- when going from small MTU, the performance rises monotonically with
increasing MTU only up to a peak at MTU=1076 (908 MBit/s). Then there's
a sudden drop to 762 MBit/s from which the throughput rises monotonically
again with further MTU increases.
- With a smaller DMA burst limit (512):
- there's a similar peak at MTU=1076 and another one at MTU=564.
- With unlimited DMA burst:
- at the default MTU=1500 I get nice 940 Mbit/s.
- the throughput rises monotonically with increasing MTU with no strange
peaks.
Notice that the peaks occur at MTU sizes that are multiples of the DMA burst
limit plus 52. Why 52? Because:
20 (IP header) + 20 (TCP header) + 12 (TCP options) = 52
The Realtek-provided r8168 driver (v8.032.00) uses unlimited TX DMA burst too,
except for CFG_METHOD_1 where the TX DMA burst is set to 512 bytes.
CFG_METHOD_1 appears to be the oldest MAC version of "RTL8168B/8111B",
i.e. RTL_GIGA_MAC_VER_11 in r8169. Not sure if this MAC version really needs
the smaller burst limit, or if any other versions have similar requirements.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Tue, 18 Sep 2012 16:50:11 +0000 (16:50 +0000)]
ipv6: unify fragment thresh handling code
Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Michal Kubeček <mkubecek@suse.cz> Cc: David Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Tue, 18 Sep 2012 16:50:10 +0000 (16:50 +0000)]
ipv6: make ip6_frag_nqueues() and ip6_frag_mem() static inline
Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Michal Kubeček <mkubecek@suse.cz> Cc: David Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Tue, 18 Sep 2012 16:50:09 +0000 (16:50 +0000)]
ipv6: unify conntrack reassembly expire code with standard one
Two years ago, Shan Wei tried to fix this:
http://patchwork.ozlabs.org/patch/43905/
The problem is that RFC2460 requires an ICMP Time
Exceeded -- Fragment Reassembly Time Exceeded message should be
sent to the source of that fragment, if the defragmentation
times out.
"
If insufficient fragments are received to complete reassembly of a
packet within 60 seconds of the reception of the first-arriving
fragment of that packet, reassembly of that packet must be
abandoned and all the fragments that have been received for that
packet must be discarded. If the first fragment (i.e., the one
with a Fragment Offset of zero) has been received, an ICMP Time
Exceeded -- Fragment Reassembly Time Exceeded message should be
sent to the source of that fragment.
"
As Herbert suggested, we could actually use the standard IPv6
reassembly code which follows RFC2460.
With this patch applied, I can see ICMP Time Exceeded sent
from the receiver when the sender sent out 3/4 fragmented
IPv6 UDP packet.
Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Michal Kubeček <mkubecek@suse.cz> Cc: David Miller <davem@davemloft.net> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: netfilter-devel@vger.kernel.org Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Tue, 18 Sep 2012 16:50:08 +0000 (16:50 +0000)]
ipv6: add a new namespace for nf_conntrack_reasm
As pointed by Michal, it is necessary to add a new
namespace for nf_conntrack_reasm code, this prepares
for the second patch.
Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Michal Kubeček <mkubecek@suse.cz> Cc: David Miller <davem@davemloft.net> Cc: Patrick McHardy <kaber@trash.net> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: netfilter-devel@vger.kernel.org Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Mon, 17 Sep 2012 20:16:31 +0000 (20:16 +0000)]
netpoll: call ->ndo_select_queue() in tx path
In netpoll tx path, we miss the chance of calling ->ndo_select_queue(),
thus could cause problems when bonding is involved.
This patch makes dev_pick_tx() extern (and rename it to netdev_pick_tx())
to let netpoll call it in netpoll_send_skb_on_dev().
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Cong Wang <amwang@redhat.com> Tested-by: Sylvain Munaut <s.munaut@whatever-company.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mika Westerberg [Fri, 14 Sep 2012 00:33:48 +0000 (00:33 +0000)]
i825xx: znet: fix compiler warnings when building a 64-bit kernel
When building 64-bit kernel with this driver we get following warnings from
the compiler:
drivers/net/ethernet/i825xx/znet.c: In function ‘hardware_init’:
drivers/net/ethernet/i825xx/znet.c:863:29: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/net/ethernet/i825xx/znet.c:870:29: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Fix these by calling isa_virt_to_bus() before passing the pointers to
set_dma_addr().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 Sep 2012 09:17:26 +0000 (09:17 +0000)]
net: provide a default dev->ethtool_ops
Instead of forcing device drivers to provide empty ethtool_ops or tweak
net/core/ethtool.c again, we could provide a generic ethtool_ops.
This occurred to me when I wanted to add GSO support to GRE tunnels.
ethtool -k support should be generic for all drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Maciej Żenczykowski <maze@google.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When moving a nic from net namespace A to net namespace B,
in dev_change_net_namesapce,we call __dev_get_by_name to
decide if the netns B has the device has the same name.
if the netns B already has the same named device,we call
dev_get_valid_name to try to get a valid name for this nic in
the netns B,but net_device->nd_net still point to netns A now.
this patch fix it.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Thu, 13 Sep 2012 19:54:57 +0000 (19:54 +0000)]
ipv6: recursive check rt->dst.from when call rt6_check_expired
If dst cache dst_a copies from dst_b, and dst_b copies from dst_c, check
if dst_a is expired or not, we should not end with dst_a->dst.from, dst_b,
we should check dst_c.
CC: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 18 Sep 2012 20:44:49 +0000 (20:44 +0000)]
net: more accurate network taps in transmit path
dev_queue_xmit_nit() should be called right before ndo_start_xmit()
calls or we might give wrong packet contents to taps users :
Packet checksum can be changed, or packet can be linearized or
segmented, and segments partially sent for the later case.
Also a memory allocation can fail and packet never really hit the
driver entry point.
Reported-by: Jamie Gloudon <jamie.gloudon@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MCDI supports requests up to 252 bytes long, which is only enough to
pass 63 RX queue IDs to MC_CMD_FLUSH_RX_QUEUES. However a VF may have
up to 64 RX queues, and if we try to flush them all we will generate
an over-length request and BUG() in efx_mcdi_copyin(). Currently
all VF drivers limit themselves to 32 RX queues, so reducing the
limit to 63 does no harm.
Also add a BUILD_BUG_ON in efx_mcdi_flush_rxqs() so we remember to
deal with the same problem there if EFX_MAX_CHANNELS is increased.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Stuart Hodgson [Mon, 3 Sep 2012 10:09:36 +0000 (11:09 +0100)]
sfc: Add support for IEEE-1588 PTP
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
This work is based on prior code by Andrew Jackson
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh:
- Add byte order conversion in efx_ptp_send_times()
- Simplify conversion of PPS event times
- Add the built-in vs module check to CONFIG_SFC_PTP dependencies] Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Wed, 19 Sep 2012 01:46:37 +0000 (02:46 +0100)]
sfc: Fix maximum array sizes for various MCDI commands
The maximum array sizes have been calculated on the basis of a maximum
SDU size of 255 bytes, whereas the actual maximum is 252 bytes.
Constructing a larger SDU will result in a BUG_ON in efx_mcdi_copyin.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Sat, 15 Sep 2012 17:11:40 +0000 (17:11 +0000)]
llc2: Remove explicit indexing of state action arrays
These arrays are accessed by iteration in
llc_exec_station_trans_actions(). There must not be any zero-filled
gaps in them, so the explicit indices are pointless.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 15 Sep 2012 17:11:25 +0000 (17:11 +0000)]
llc2: Collapse the station event receive path
We only ever put one skb on the event queue, and then immediately
process it. Remove the queue and fold together the related functions,
removing several blatantly false comments.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 15 Sep 2012 17:11:18 +0000 (17:11 +0000)]
llc2: Remove dead code for state machine
The initial state is UP and there is no way to enter the other states
as the required event type is never generated. Delete all states,
event types, and other dead code. The only thing left is handling
of the XID and TEST commands.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Vick [Fri, 17 Aug 2012 01:30:37 +0000 (01:30 +0000)]
igb: Add 1588 support to I210/I211.
Previously I210/I211 followed the same code flow as 82580/I350 for 1588.
However, since the register sets have changed, we must update the
implementation to accommodate the register changes.
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Matthew Vick <matthew.vick@intel.com> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Sat, 18 Aug 2012 07:26:33 +0000 (07:26 +0000)]
igb: Prevent dropped Tx timestamps via work items and interrupts.
In rare circumstances, it's possible a descriptor writeback will occur
before a timestamped Tx packet will go out on the wire, leading to the
driver believing the hardware failed to timestamp the packet. Schedule a
work item for 82576 and use the available time sync interrupt registers
on 82580 and above to account for this.
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Fri, 10 Aug 2012 05:40:46 +0000 (05:40 +0000)]
igb: Store the MAC address in the name in the PTP struct.
Change the name of the adapter in the PTP struct to enable easier
correlation between interface and PTP device.
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Matthew Vick <matthew.vick@intel.com> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Tue, 28 Aug 2012 06:33:05 +0000 (06:33 +0000)]
igb: Correct PTP support query from ethtool.
Update ethtool_get_ts_info to not report any supported functionality on
82575 and add support for V2 Sync and V2 Delay packets. In the case
where CONFIG_IGB_PTP is not defined, we should be reporting default
values.
v2: Correct the function to return EOPNOTSUPP when there is no PTP support
or the device does not support PTP. Also fix minor whitespace issue.
Signed-off-by: Matthew Vick <matthew.vick@intel.com> Cc: Richard Cochran <richardcochran@gmail.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Fri, 10 Aug 2012 05:40:44 +0000 (05:40 +0000)]
igb: Update PTP function names/variables and locations.
Where possible, move PTP-related functions into igb_ptp.c and update the
names of functions and variables to match the established coding style
in the files and specify that they are PTP-specific.
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Fri, 10 Aug 2012 05:40:43 +0000 (05:40 +0000)]
igb: Tidy up wrapping for CONFIG_IGB_PTP.
For users without CONFIG_IGB_PTP=y, we should not be compiling any PTP
code into the driver. Tidy up the wrapping in igb to support this.
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Matthew Vick <matthew.vick@intel.com> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Mon, 17 Sep 2012 04:57:32 +0000 (00:57 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
This is another batch of updates intended for the 3.7 stream.
There are not a lot of large items, but iwlwifi, mwifiex, rt2x00,
ath9k, and brcmfmac all get some attention. Wei Yongjun also provides
a series of small maintenance fixes.
This also includes a pull of the wireless tree in order to satisfy
some prerequisites for later patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Rustad [Wed, 18 Jul 2012 06:05:50 +0000 (06:05 +0000)]
ixgbe: Improve statistics accuracy for DDP traffic
Noticed that the byte and packet count statistics are under-
counting traffic handled by the DDP offload when there is more
than one DDP completion processed in a single call to
ixgbe_clean_rx_irq. This patch fixes that.
I tried to optimize the setting of the rss value so that it
only would have to be computed once, and only when there is
a DDP completion present.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added the reg_ops file to debugfs with commands to read and write
a register to give users the ability to read and write individual
registers on the fly.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added the netdev_ops file to debugfs with a command to call the
ndo_tx_timeout function to give users the ability to simulate a
tx_timeout call made by the kernel.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 8 Aug 2012 06:28:37 +0000 (06:28 +0000)]
ixgbe: fix reporting of spoofed packets
Use %u instead of %d to display u32 variable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Robert Garrett <RobertX.Garrett@intel.com> Tested-by: Robert Garrett <RobertX.Garrett@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 20 Jul 2012 08:09:06 +0000 (08:09 +0000)]
ixgbe: Fix VF rate limiting to correctly account for more queues per VF
This change fixes the assumptions of the rate limiting code that previously
assumed that each VF would only ever have 2 queues. This update makes it
so that we now use a queues per pool value that is determined based on the
VMDq feature mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-By: John Fastabend <john.r.fastabend@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Robert Garrett <RobertX.Garrett@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 23 May 2012 05:39:25 +0000 (05:39 +0000)]
ixgbe: Fix ordering of things so that PF correctly configures its VLANs
The PF was not correctly registering any of its VLANs. As a result any
VLAN tagged traffic from the VF would not be delivered to the PF because
the VLAN was never assigned to the PF pool.
In addition the VF was not allowed to receive traffic from VLAN 0 if it was
allowed to receive untagged frames. This change corrects that so that it
will correctly receive traffic from VLAN 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Otto Estuardo Solares Cabrera <solca@galileo.edu> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather easy conflict resolution, the 'net' tree had bug fixes to make
sure we checked if a socket is a time-wait one or not and elide the
logging code if so.
Whereas on the 'net-next' side we are calculating the UID and GID from
the creds using different interfaces due to the user namespace changes
from Eric Biederman.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull GFS2 fixes from Steven Whitehouse:
"Here are three GFS2 fixes for the current kernel tree. These are all
related to the block reservation code which was added at the merge
window. That code will be getting an update at the forthcoming merge
window too. In the mean time though there are a few smaller issues
which should be fixed.
The first patch resolves an issue with write sizes of greater than 32
bits with the size hinting code. The second ensures that the
allocation data structure is initialised when using xattrs and the
third takes into account allocations which may have been made by other
nodes which affect a reservation on the local node."
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Take account of blockages when using reserved blocks
GFS2: Fix missing allocation data for set/remove xattr
GFS2: Make write size hinting code common
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"A few small updates for 3.6 - a trivial regression fix and a couple of
conformance updates for the gmux driver, plus some tiny fixes for
asus-wmi, eeepc-laptop and thinkpad_acpi."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
thinkpad_acpi: buffer overflow in fan_get_status()
eeepc-laptop: fix device reference count leakage in eeepc_rfkill_hotplug()
platform/x86: fix asus_laptop.wled_type description
asus-laptop: HRWS/HWRS typo
drivers-platform-x86: remove useless #ifdef CONFIG_ACPI_VIDEO
apple-gmux: Fix port address calculation in gmux_pio_write32()
apple-gmux: Fix index read functions
apple-gmux: Obtain version info from indexed gmux
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
"The last bunch of (typical) i2c-embedded driver fixes for 3.6.
Also update the MAINTAINERS file to point to my tree since people keep
asking where to find their patches."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: algo: pca: Fix mode selection for PCA9665
MAINTAINERS: fix tree for current i2c-embedded development
i2c: mxs: correctly setup speed for non devicetree
i2c: pnx: Fix read transactions of >= 2 bytes
i2c: pnx: Fix bit definitions
Merge tag 'ecryptfs-3.6-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
- Fixes a regression, introduced in 3.6-rc1, when a file is closed
before its shared memory mapping is dirtied and unmapped. The lower
file was being released when the eCryptfs file was closed and the
dirtied pages could not be written out.
- Adds a call to the lower filesystem's ->flush() from
ecryptfs_flush().
- Fixes a regression, introduced in 2.6.39, when a file is renamed on
top of another file. The target file's inode was not being evicted
and the space taken by the file was not reclaimed until eCryptfs was
unmounted.
* tag 'ecryptfs-3.6-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Copy up attributes of the lower target inode after rename
eCryptfs: Call lower ->flush() from ecryptfs_flush()
eCryptfs: Write out all dirty pages just before releasing the lower file
Merge branch 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull one more DMA-mapping fix from Marek Szyprowski:
"This patch fixes very subtle bug (typical off-by-one error) which
might appear in very rare circumstances."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: mm: fix DMA pool affiliation check
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix word size register read and write operations in ina2xx driver, and
initialize uninitialized structure elements in twl4030-madc-hwmon
driver."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ina2xx) Fix word size register read and write operations
hwmon: (twl4030-madc-hwmon) Initialize uninitialized structure elements
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I realise this a bit bigger than I would want at this point.
Exynos is a large chunk, I got them to half what they wanted already,
and hey its ARM based, so not going to hurt many people.
Radeon has only two fixes, but the PLL fixes were a bit bigger, but
required for a lot of scenarios, the fence fix is really urgent.
vmwgfx: I've pulled in a dumb ioctl support patch that I was going to
shove in later and cc stable, but we need it asap, its mainly to stop
mesa growing a really ugly dependency in userspace to run stuff on
vmware, and if I don't stick it in the kernel now, everyone will have
to ship ugly userspace libs to workaround it.
nouveau: single urgent fix found in F18 testing, causes X to not start
properly when f18 plymouth is used
i915: smattering of fixes and debug quieting
gma500: single regression fix
So as I said a bit large, but its fairly well scattered and its all
stuff I'll be shipping in F18's 3.6 kernel."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (26 commits)
drm/nouveau: fix booting with plymouth + dumb support
drm/radeon: make 64bit fences more robust v3
drm/radeon: rework pll selection (v3)
drm: Drop the NV12M and YUV420M formats
drm/exynos: remove DRM_FORMAT_NV12M from plane module
drm/exynos: fix double call of drm_prime_(init/destroy)_file_private
drm/exynos: add dummy support for dmabuf-mmap
drm/exynos: Add missing braces around sizeof in exynos_mixer.c
drm/exynos: Add missing braces around sizeof in exynos_hdmi.c
drm/exynos: Make g2d_pm_ops static
drm/exynos: Add dependency for G2D in Kconfig
drm/exynos: fixed page align bug.
drm/exynos: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/exynos: Use devm_* functions in exynos_drm_g2d.c file
drm/exynos: Use devm_kzalloc in exynos_drm_hdmi.c file
drm/exynos: Use devm_kzalloc in exynos_drm_vidi.c file
drm/exynos: Remove redundant check in exynos_drm_fimd.c file
drm/exynos: Remove redundant check in exynos_hdmi.c file
vmwgfx: add dumb ioctl support
gma500: Fix regression on Oaktrail devices
...
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This tree includes various fixes"
Ingo really needs to improve on the whole "explain git pull" part.
"Various fixes" indeed.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/hwpb: Invoke __perf_event_disable() if interrupts are already disabled
perf/x86: Enable Intel Cedarview Atom suppport
perf_event: Switch to internal refcount, fix race with close()
oprofile, s390: Fix uninitialized memory access when writing to oprofilefs
perf/x86: Fix microcode revision check for SNB-PEBS
Merge tag 'usb-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are a number of USB patches, a bit more than I normally like this
late in the -rc series, but given people's vacations (myself
included), and the kernel summit, it seems to have happened this way.
All are tiny, but they add up. A number of gadget and xhci fixes, and
a few new device ids. All have been tested in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: don't stall endpoint if request list is empty in isr_tr_complete_low
usb: chipidea: cleanup dma_pool if udc_start() fails
usb: chipidea: udc: fix error path in udc_start()
usb: chipidea: udc: add pullup fuction, needed by the uvc gadget
usb: chipidea: udc: fix setup of endpoint maxpacket size
USB: option: replace ZTE K5006-Z entry with vendor class rule
EHCI: Update qTD next pointer in QH overlay region during unlink
USB: cdc-wdm: fix wdm_find_device* return value
USB: ftdi_sio: do not claim CDC ACM function
usb: dwc3: gadget: fix pending isoc handling
usb: renesas_usbhs: fixup DMA transport data alignment
usb: gadget: at91udc: Don't check for ep->ep.desc
usb: gadget: at91udc: don't overwrite driver data
usb: dwc3: core: fix incorrect usage of resource pointer
usb: musb: musbhsdma: fix IRQ check
usb: musb: tusb6010: fix error path in tusb_probe()
usb: musb: host: fix for musb_start_urb Oops
usb: gadget: dummy_hcd: add support for USB_DT_BOS on rh
usb: gadget: dummy_hcd: fixup error probe path
usb: gadget: s3c-hsotg.c: fix error return code
...
Merge tag 'driver-core-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg Kroah-Hartman:
"Here is one fix for 3.6-rc6 for the kobject.h file.
It fixes a reported oops if CONFIG_HOTPLUG is disabled. It's been in
the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: fix oops with "input0: bad kobj_uevent_env content in show_uevent()"
vfs: make O_PATH file descriptors usable for 'fstat()'
We already use them for openat() and friends, but fstat() also wants to
be able to use O_PATH file descriptors. This should make it more
directly comparable to the O_SEARCH of Solaris.
Note that you could already do the same thing with "fstatat()" and an
empty path, but just doing "fstat()" directly is simpler and faster, so
there is no reason not to just allow it directly.
See also commit 332a2e1244bd, which did the same thing for fchdir, for
the same reasons.
Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org # O_PATH introduced in 3.0+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eCryptfs: Copy up attributes of the lower target inode after rename
After calling into the lower filesystem to do a rename, the lower target
inode's attributes were not copied up to the eCryptfs target inode. This
resulted in the eCryptfs target inode staying around, rather than being
evicted, because i_nlink was not updated for the eCryptfs inode. This
also meant that eCryptfs didn't do the final iput() on the lower target
inode so it stayed around, as well. This would result in a failure to
free up space occupied by the target file in the rename() operation.
Both target inodes would eventually be evicted when the eCryptfs
filesystem was unmounted.
This patch calls fsstack_copy_attr_all() after the lower filesystem
does its ->rename() so that important inode attributes, such as i_nlink,
are updated at the eCryptfs layer. ecryptfs_evict_inode() is now called
and eCryptfs can drop its final reference on the lower inode.
http://launchpad.net/bugs/561129
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Tested-by: Colin Ian King <colin.king@canonical.com> Cc: <stable@vger.kernel.org> [2.6.39+]
eCryptfs: Call lower ->flush() from ecryptfs_flush()
Since eCryptfs only calls fput() on the lower file in
ecryptfs_release(), eCryptfs should call the lower filesystem's
->flush() from ecryptfs_flush().
If the lower filesystem implements ->flush(), then eCryptfs should try
to flush out any dirty pages prior to calling the lower ->flush(). If
the lower filesystem does not implement ->flush(), then eCryptfs has no
need to do anything in ecryptfs_flush() since dirty pages are now
written out to the lower filesystem in ecryptfs_release().
eCryptfs: Write out all dirty pages just before releasing the lower file
Fixes a regression caused by:
821f749 eCryptfs: Revert to a writethrough cache model
That patch reverted some code (specifically, 32001d6f) that was
necessary to properly handle open() -> mmap() -> close() -> dirty pages
-> munmap(), because the lower file could be closed before the dirty
pages are written out.
Rather than reapplying 32001d6f, this approach is a better way of
ensuring that the lower file is still open in order to handle writing
out the dirty pages. It is called from ecryptfs_release(), while we have
a lock on the lower file pointer, just before the lower file gets the
final fput() and we overwrite the pointer.
Thomas Kavanagh [Thu, 13 Sep 2012 15:16:55 +0000 (08:16 -0700)]
i2c: algo: pca: Fix mode selection for PCA9665
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net> Signed-off-by: Guenter Roeck <groeck@juniper.net> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Dave Airlie [Fri, 14 Sep 2012 01:20:46 +0000 (11:20 +1000)]
Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex writes:
This is the current set of radeon fixes for 3.6. Two small fixes:
- fix the fence issues introduced in 3.5 with 64-bit fences
- PLL fix for multiple DP heads
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: make 64bit fences more robust v3
drm/radeon: rework pll selection (v3)
pktgen: fix crash with vlan and packet size less than 46
If vlan option is being specified in the pktgen and packet size
being requested is less than 46 bytes, despite being illogical
request, pktgen should not crash the kernel.
The root cause of why pktgen is not able to handle this case is due
to comparison of signed (datalen) and unsigned data (sizeof), which
eventually passes a huge number to skb_put().
Signed-off-by: Nishank Trivedi <nistrive@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Acked-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Tue, 11 Sep 2012 21:59:01 +0000 (21:59 +0000)]
ipv6: replace write lock with read lock when get route info
geting route info does not write rt->rt6i_table, so replace
write lock with read lock
Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Sat, 1 Sep 2012 19:54:07 +0000 (12:54 -0700)]
thinkpad_acpi: buffer overflow in fan_get_status()
The acpi_evalf() function modifies four bytes of data but in
fan_get_status() we pass a pointer to u8. I have modified the
function to use type checking now.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Matthew Garrett <mjg@redhat.com>
Bernhard Froemel [Sat, 25 Aug 2012 08:30:48 +0000 (10:30 +0200)]
apple-gmux: Fix index read functions
Study of Apple's binary driver revealed that the GMUX_READ_PORT should
be written between calls to gmux_index_wait_ready and
gmux_index_wait_complete (i.e., the new index protocol must be
followed). If this is not done correctly, the indexed
gmux device only partially accepts writes which lead to problems
concerning GPU switching. Special thanks to Seth Forshee who helped
greatly with identifying unnecessary changes.
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at> Signed-off-by: Matthew Garrett <mjg@redhat.com>
Commit a334872224a67b614dc888460377862621f3dac7 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).
This patch adds the missing segments, fixing said issues.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: correct advertisement of pause capabilities
This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.
This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Add labels for site-local and 6bone testing addresses (RFC6724)
Added labels for site-local addresses (fec0::/10) and 6bone testing
addresses (3ffe::/16) in order to depreference them.
Note that the RFC introduced new rows for Teredo, ULA and 6to4 addresses
in the default policy table. Some of them have different labels from ours.
For backward compatibility, we do not change the "default" labels.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The scsi netlink code confuses the netlink port id with a process id,
going so far as to read NETLINK_CREDS(skb)->pid instead of the correct
NETLINK_CB(skb).pid. Fortunately it does not matter because nothing
registers to respond to scsi netlink requests.
The only interesting use of the scsi_netlink interface is
fc_host_post_vendor_event which sends a netlink multicast message.
Since nothing registers to handle scsi netlink messages kill all of the
registration logic, while retaining the same error handling behavior
preserving the userspace visible behavior and removing all of the
confused code that thought a netlink port id was a process id.
This was tested with a kernel allyesconfig build which had no problems.
Cc: James Bottomley <James.Bottomley@parallels.com> Cc: James Smart <James.Smart@Emulex.Com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netprio_cgroup: Remove update_netdev_tables() since it is unnecessary
The update_netdev_tables() function appears to be unnecessary, since the
write_update_netdev_table() function will adjust the priomaps as and when
required anyway. So drop the usage of update_netdev_tables() entirely.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Christian König [Thu, 13 Sep 2012 08:33:47 +0000 (10:33 +0200)]
drm/radeon: make 64bit fences more robust v3
Only increase the higher 32bits if we really detect a wrap around.
v2: instead of increasing the higher 32bits just use the higher
32bits from the last emitted fence.
v3: also use last emitted fence value as upper limit.
The intention of this patch is to make fences as robust as
they where before introducing 64bit fences. This is
necessary because on older systems it looks like the fence
value gets corrupted on initialization.
Should also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=54129
https://bugs.freedesktop.org/show_bug.cgi?id=54662
https://bugzilla.redhat.com/show_bug.cgi?id=846505
https://bugzilla.redhat.com/show_bug.cgi?id=845639
3.5 needs a separate patch due to changes in the
fence code. Will send that out separately.
Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 31 Aug 2012 15:56:50 +0000 (11:56 -0400)]
drm/radeon: rework pll selection (v3)
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
net: qmi_wwan: call subdriver with control intf only
This fixes a hang on suspend due to calling wdm_suspend on
the unregistered data interface. The hang should have been
a NULL pointer reference had it not been for a logic error
in the cdc_wdm code.
commit 230718bd net: qmi_wwan: bind to both control and data interface
changed qmi_wwan to use cdc_wdm as a subdriver for devices with
a two-interface QMI/wwan function. The commit failed to update
qmi_wwan_suspend and qmi_wwan_resume, which were written to handle
either a single combined interface function, or no subdriver at all.
The result was that we called into the subdriver both when the
control interface was suspended and when the data interface was
suspended. Calling the subdriver suspend function with an
unregistered interface is not supported and will make the
subdriver bug out.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log