James Smart [Thu, 17 Aug 2006 12:00:43 +0000 (08:00 -0400)]
[SCSI] fc transport: add fc_host system_hostname attribute and u64_to_wwn()
This patch updates the fc transport for the following:
- Addition of a new attribute "system_hostname" which can be
used to set the fully qualified hostname that the fc_host
is attached to. The fc_host can then register this string
as the FDMI-based host name attribute.
Note: for NPIV, a fc_host could be associated with a system which
is not the local system.
- Add the inline function u64_to_wwn(), which is the inverse of the
existing wwn_to_u64() function.
- Slight reorg, just to keep dynamic attributes with each other, etc
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Randy Dunlap [Tue, 15 Aug 2006 06:09:23 +0000 (23:09 -0700)]
[SCSI] aic7*: cleanup MODULE_PARM_DESC strings
Modify beginning string to be more readable. Remove one trailing newline.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] Don't add scsi_device for devices that return PQ=1, PDT=0x1f
Some targets may return slight variations of PQ and PDT to indicate
no LUN mapped. USB UFI setting PDT=0x1f but having reserved bits for
PQ is one example, and NetApp targets returning PQ=1 and PDT=0x1f is
another. Both instances seem like reasonable responses according to
SPC-3 and UFI specs.
The current scsi_probe_and_add_lun() code adds a scsi_device
for targets that return PQ=1 and PDT=0x1f. This causes LUNs of type
"UNKNOWN" to show up in /proc/scsi/scsi when no LUNs are mapped.
In addition, subsequent rescans fail to recognize LUNs that may be
added on the target, unless preceded by a write to the delete attribute
of the "UNKNOWN" LUN.
This patch addresses this problem by skipping over the scsi_add_lun()
when PQ=1,PDT=0x1f is encountered, and just returns
SCSI_SCAN_TARGET_PRESENT.
Signed-off-by: Dave Wysochanski <davidw@netapp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Thu, 3 Aug 2006 15:03:30 +0000 (08:03 -0700)]
[SCSI] aacraid: Reset adapter in recovery timeout
Received from Mark Salyzyn
If the adapter is in blinkled (Firmware Assert) when error recovery
timeout actions have been triggered, perform an adapter warm reset and
restart the initialization.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Tue, 8 Aug 2006 15:52:14 +0000 (08:52 -0700)]
[SCSI] aacraid: Restart adapter on firmware assert (Update 2)
Received from Mark Salyzyn
If the adapter should be in a blinkled (Firmware Assert) state when the
driver loads, we will perform a warm restart of the Adapter Firmware to
see if we can rescue the adapter. Possible causes of a blinkled can
occur on some early release motherboard BIOSes, transitory PCI bus
problems on embedded systems or non-x86 based architectures, transitory
startup failures of early release drives or transitory hardware
failures; some of which can bite the adapter later at runtime. Future
enhancements will include recovery during runtime.
Fixed extra whitespace space issue.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Thu, 3 Aug 2006 15:02:24 +0000 (08:02 -0700)]
[SCSI] aacraid: interruptible ioctl
Received from Mark Salyzyn
This patch allows the FSACTL_SEND_LARGE_FIB, FSACTL_SENDFIB and
FSACTL_SEND_RAW_SRB ioctl calls into the aacraid driver to be
interruptible. Only necessary if the adapter and/or the management
software has gone into some sort of misbehavior and the system is being
rebooted, thus permitting the user management software applications to
be killed relatively cleanly. The FIB queue resource is held out of the
free queue until the adapter finally, if ever, completes the command.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This stack overflow occurred during tests on s390 using zfcp.
Recursion depth for this panic was 19.
Usually recursion between blk_run_queue and a request_fn is avoided
using QUEUE_FLAG_REENTER. But this does not help if the scsi stack
tries to flush the starved_list of a scsi_host.
Limit recursion depth when flushing the starved_list
of a scsi_host.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Matthew Wilcox [Tue, 4 Jul 2006 18:15:20 +0000 (12:15 -0600)]
[SCSI] Improve inquiry printing
- Replace scsi_device_types array API with scsi_device_type function API.
Gets rid of a lot of common code, as well as being easier to use.
- Add the new device types in SPC4 r05a, and rename some of the older ones.
- Reformat the printing of inquiry data; now fits on one line and
includes PQ.
I think I've addressed all the feedback from the previous versions. My
current test box prints:
scsi 2:0:1:0: Direct access HP 18.2G ATLAS10K3_18_SCA HP05 PQ: 0 ANSI: 2
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Michael Reed [Mon, 31 Jul 2006 17:19:30 +0000 (12:19 -0500)]
[SCSI] mptfc: add additional fc transport attributes
Add host_supported_speeds, host_maxframe_size, host_speed, host_fabric_name,
host_port_type, host_port_state, and host_symbolic_name transport attributes
to fusion fibre channel.
Signed-off-by: Michael Reed <mdr@sgi.com> Acked-by: Moore, Eric <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Thu, 3 Aug 2006 18:54:59 +0000 (13:54 -0500)]
[SCSI] DAC960: PCI id table fixup
The PCI ID table in the DAC960 driver conflicts with some devices
that use the ipr driver. All ipr adapters that use this chip
have an IBM subvendor ID and all DAC960 adapters that use this
chip have a Mylex subvendor id.
Signed-off-by: Brian King <brking@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Dave Jones [Wed, 2 Aug 2006 21:11:49 +0000 (17:11 -0400)]
[SCSI] advansys pci tweaks.
Remove a lot of duplicate #defines from the advansys driver,
and make them look like PCI IDs as defined elsewhere in the kernel.
Also add a module table so that it automatically gets picked up
by tools relying on modinfo output (like say, distro installers).
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Fri, 28 Jul 2006 22:36:46 +0000 (17:36 -0500)]
[SCSI] arcmsr: fix up sysfs values
The sysfs files in arcmsr are non-standard in that they aren't simple
filename value pairs, the values actually contain preceeding text which
would have to be parsed. The idea of sysfs files is that the file name
is the description and the contents is a simple value.
Fix up arcmsr to conform to this standard.
Acked-By: Erich Chen <erich@areca.com.tw> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Andrew Morton [Sat, 29 Jul 2006 18:14:08 +0000 (11:14 -0700)]
[SCSI] areca sysfs fix
Remove sysfs_remove_bin_file() return-value checking from the areca driver.
There's nothing a driver can do if sysfs file removal fails, so we'll soon be
changing sysfs_remove_bin_file() to internally print a diagnostic and to
return void.
Cc: Erich Chen <erich@areca.com.tw> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Erich Chen [Wed, 12 Jul 2006 15:59:32 +0000 (08:59 -0700)]
[SCSI] arcmsr: initial driver, version 1.20.00.13
arcmsr is a driver for the Areca Raid controller, a host based RAID
subsystem that speaks SCSI at the firmware level.
This patch is quite a clean up over the initial submission with
contributions from:
Randy Dunlap <rdunlap@xenotime.net>
Christoph Hellwig <hch@lst.de>
Matthew Wilcox <matthew@wil.cx>
Adrian Bunk <bunk@stusta.de>
Signed-off-by: Erich Chen <erich@areca.com.tw> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[PATCH] fix compile regression for a few scsi drivers
This fixes three drivers to compile again after my patch that removes
the data_cmnd member from struct scsi_cmnd.
The fas216 change is trivial, it should have been using ->cmnd all the
time.
NCR53C9 (which seem to be mostly duplicate driver with esp.c!) is doing
something odd, it should only have looked at ->cmnd before not the saved
copy that is kept for the error handlers sake. Note that it really
should deal with the sync setting themselves but use the generic domain
validation code that get this right - but that's for later let's push
this simple compile fix for now.
And sorry for the late fix for this, I have been busy with OLS and
associated activities last week.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SCSI] esp: Fix build.
[SPARC]: Fix SA_STATIC_ALLOC value.
[SPARC64]: Explicitly print return PC when the kernel fault PC is bogus.
Arjan van de Ven [Wed, 26 Jul 2006 13:40:07 +0000 (15:40 +0200)]
[PATCH] Reorganize the cpufreq cpu hotplug locking to not be totally bizare
The patch below moves the cpu hotplugging higher up in the cpufreq
layering; this is needed to avoid recursive taking of the cpu hotplug
lock and to otherwise detangle the mess.
The new rules are:
1. you must do lock_cpu_hotplug() around the following functions:
__cpufreq_driver_target
__cpufreq_governor (for CPUFREQ_GOV_LIMITS operation only)
__cpufreq_set_policy
2. governer methods (.governer) must NOT take the lock_cpu_hotplug()
lock in any way; they are called with the lock taken already
3. if your governer spawns a thread that does things, like calling
__cpufreq_driver_target, your thread must honor rule #1.
4. the policy lock and other cpufreq internal locks nest within
the lock_cpu_hotplug() lock.
I'm not entirely happy about how the __cpufreq_governor rule ended up
(conditional locking rule depending on the argument) but basically all
callers pass this as a constant so it's not too horrible.
The patch also removes the cpufreq_governor() function since during the
locking audit it turned out to be entirely unused (so no need to fix it)
The patch works on my testbox, but it could use more testing
(otoh... it can't be much worse than the current code)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recvmsg() for raw socket seems to return random u16 value
from the kernel stack memory since port field is not initialized.
But I'm not sure this patch is correct.
Does raw socket return any information stored in port field?
[ BSD defines RAW IP recvmsg to return a sin_port value of zero.
This is described in Steven's TCP/IP Illustrated Volume 2 on
page 1055, which is discussing the BSD rip_input() implementation. ]
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
IP multicast route code was reusing an skb which causes use after free
and double free.
From: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Note, it is real skb_clone(), not alloc_skb(). Equeued skb contains
the whole half-prepared netlink message plus room for the rest.
It could be also skb_copy(), if we want to be puristic about mangling
cloned data, but original copy is really not going to be used.
Acked-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] cciss: fix stall with softirq handling and CFQ
We need to postpone the queue startup until after the softirq
handler has actually finished some requests, otherwise we could
be racing with cciss_softirq_done() and not actually restart
the queue handling.
Patrick McHardy [Tue, 25 Jul 2006 05:54:55 +0000 (22:54 -0700)]
[NETFILTER]: bridge netfilter: add deferred output hooks to feature-removal-schedule
Add bridge netfilter deferred output hooks to feature-removal-schedule
and disable them by default. Until their removal they will be
activated by the physdev match when needed.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Oester [Tue, 25 Jul 2006 05:54:14 +0000 (22:54 -0700)]
[NETFILTER]: xt_pkttype: fix mismatches on locally generated packets
Locally generated broadcast and multicast packets have pkttype set to
PACKET_LOOPBACK instead of PACKET_BROADCAST or PACKET_MULTICAST. This
causes the pkttype match to fail to match packets of either type.
The below patch remedies this by using the daddr as a hint as to
broadcast|multicast. While not pretty, this seems like the only way
to solve the problem short of just noting this as a limitation of the
match.
This resolves netfilter bugzilla #484
Signed-off-by: Phil Oester <kernel@linuxace.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 25 Jul 2006 05:52:47 +0000 (22:52 -0700)]
[NETFILTER]: nf_queue: handle NF_STOP and unknown verdicts in nf_reinject
In case of an unknown verdict or NF_STOP the packet leaks. Unknown verdicts
can happen when userspace is buggy. Reinject the packet in case of NF_STOP,
drop on unknown verdicts.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 25 Jul 2006 05:47:14 +0000 (22:47 -0700)]
[SCSI] esp: Fix build.
The data_cmd[] member got deleted, so do not use it any more. Scsi
commands do not have their ->cmd[] overwritten temporary to probe for
status after an error before retrying.
Signed-off-by: David S. Miller <davem@davemloft.net>
skbuff.h has an #ifndef CONFIG_HAVE_ARCH_DEV_ALLOC_SKB to allow
architectures to reimplement __dev_alloc_skb. It's not set on any
architecture and now that we have an architecture-overrideable
NET_SKB_PAD there is not point at all to have one either.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Rompf [Mon, 24 Jul 2006 20:52:13 +0000 (13:52 -0700)]
[VLAN]: Fix link state propagation
When the queue of the underlying device is stopped at initialization time
or the device is marked "not present", the state will be propagated to the
vlan device and never change. Based on an analysis by Patrick McHardy.
Signed-off-by: Stefan Rompf <stefan@loplof.de> ACKed-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Jul 2006 20:49:06 +0000 (13:49 -0700)]
[IPV6] xfrm6_tunnel: Delete debugging code.
It doesn't compile, and it's dubious in several regards:
1) is enabled by non-Kconfig controlled CONFIG_* value
(noted by Randy Dunlap)
2) XFRM6_TUNNEL_SPI_MAGIC is defined after it's first use
3) the debugging messages print object pointer addresses
which have no meaning without context
So let's just get rid of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
[Bluetooth] Enable SCO support for Broadcom HID proxy dongle
The Broadcom dongles with HID proxy support actually support SCO over
HCI if the SCO buffer size values are corrected. So instead of disabling
the SCO support, mark this dongle with the quirk for the Bluetooth core
to correct the wrong buffer size values.
[Bluetooth] Add quirk for another broken RTX Telecom based dongle
This patch disables the ISOC transfers for another broken RTX Telecom
based USB dongle. Starting the USB ISOC transfers only ends in a burst
of error messages for invalid SCO packets on connection handle 0.
[Bluetooth] Correct SCO buffer size for Belkin devices
The Belkin F8T012 and F8T013 devices are both based on a Bluetooth chip
from Broadcom and their SCO buffer size values are wrong. The Bluetooth
core should correct these values.
[Bluetooth] Correct SCO buffer size for another Broadcom chip
The SCO buffer size values on IBM/Lenovo ThinkPad laptops with a
Bluetooth chip from Broadcom are wrong. The USB Bluetooth driver
has to set a quirk to correct the SCO buffer size values.
[Bluetooth] Correct RFCOMM channel MTU for broken implementations
Some Bluetooth RFCOMM implementations try to negotiate a bigger channel
MTU than we can support for a particular session. The maximum MTU for
a RFCOMM session is limited through the L2CAP layer. So if the other
side proposes a channel MTU that is bigger than the underlying L2CAP
MTU, we should reduce it to the L2CAP MTU of the session minus five
bytes for the RFCOMM headers.
In PSCHED_TADD and PSCHED_TADD2, if delta is less than tv.tv_usec (so,
less than USEC_PER_SEC too) then tv_res will be smaller than tv. The
affectation "(tv_res).tv_usec = __delta;" is wrong. The fix is to
revert to the original code before 4ee303dfeac6451b402e3d8512723d3a0f861857 and change the 'if' in
'while'.
I went to alter the default sysctl and it didn't take for new sockets.
Below patch fixes this.
I think the default is too low but it is what the DCCP spec specifies.
As a side effect of this my rx speed using iperf goes from about 2.8 Mbits/sec
to 3.5. This is still far too slow but it is a step in the right direction.
Compile tested only for IPv6 but not particularly complex change.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
IB/ipoib: Fix packet loss after hardware address update
The neighbour ha field may get updated without destroying the
neighbour. In this case, the ha field gets out of sync with the
address handle stored in ipoib_neigh->ah, with the result that
the ah field would point to an incorrect path, resulting in all
packets being lost.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sean Hefty [Thu, 20 Jul 2006 08:25:50 +0000 (11:25 +0300)]
IB/mad: Validate MADs for spec compliance
Validate MADs sent by userspace clients for spec compliance with
C13-18.1.1 (prevent duplicate requests and responses sent on the
same port). Without this, RMPP transactions get aborted because
of duplicate packets.
This patch is similar to that provided by Jack Morgenstein.
Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell [Tue, 18 Jul 2006 01:21:24 +0000 (18:21 -0700)]
IB/ipath: ipath_skip_sge() can break if num_sge > 1
ipath_skip_sge() doesn't exactly duplicate the side effects of
ipath_copy_sge() if num_sge > 1 since it doesn't decrement ss->num_sge.
This could result in the sg_list being accessed out of bounds.
Since ipath_skip_sge() is almost always called with num_sge == 1,
the original "optimization" is almost never used.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell [Tue, 18 Jul 2006 01:19:54 +0000 (18:19 -0700)]
IB/ipath: Fix ib_ipath driver to work with SRP
I am still working on a proposal to remove the phys_to_virt() calls
in the ib_ipath driver. In the mean time, this patch allows SRP
to work by fixing the R_Key check and conversion from IB address
to kernel virtual address. It also returns the correct page size
for FMRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell [Tue, 18 Jul 2006 01:18:36 +0000 (18:18 -0700)]
IB/ipath: Fix a data corruption
This patch fixes a problem where certain error packets are passed
to the InfiniBand layer for processing even though the packet
actually was received with an error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mem-free HCAs always keep one spare SRQ WQE, so the SRQ limit cannot
be set beyond srq->max - 1.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il> Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier [Sun, 23 Jul 2006 22:16:04 +0000 (15:16 -0700)]
IB/uverbs: Fix lockdep warnings
Lockdep warns because uverbs is trying to take uobj->mutex when it
already holds that lock. This is because there are really multiple
types of uobjs even though all of their locks are initialized in
common code.
ib_uverbs_create_ah() and ib_uverbs_create_srq() did not release the
PD's read lock in their error paths, which lead to deadlock when
destroying the PD.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Paul Jackson [Sun, 23 Jul 2006 18:36:08 +0000 (11:36 -0700)]
[PATCH] Cpuset: fix ABBA deadlock with cpu hotplug lock
Fix ABBA deadlock between lock_cpu_hotplug() and the cpuset
callback_mutex lock.
It only happens on cpu_exclusive cpusets, due to the dynamic
sched domain code trying to take the cpu hotplug lock inside
the cpuset callback_mutex lock.
This bug has apparently been here for several months, but didn't
get hit until the right customer load on a large system.
This fix appears right from inspection, but it will take a few
more days running it on that customers workload to be confident
we nailed it. We don't have any other reproducible test case.
The cpu_hotplug_lock() tends to cover large runs of code.
The other places that hold both that lock and the cpuset callback
mutex lock always nest the cpuset lock inside the hotplug lock.
This place tries to do the reverse, risking an ABBA deadlock.
This is in the cpuset_rmdir() code, where we:
* take the callback_mutex lock
* mark the cpuset CS_REMOVED
* call update_cpu_domains for cpu_exclusive cpusets
* in that call, take the cpu_hotplug lock if the
cpuset is marked for removal.
Thanks to Jack Steiner for identifying this deadlock.
The fix is to tear down the dynamic sched domain before we grab
the cpuset callback_mutex lock. This way, the two locks are
serialized, with the hotplug lock taken and released before
trying for the cpuset lock.
I suspect that this bug was introduced when I changed the
cpuset locking from one lock to two. The dynamic sched domain
dependency on cpu_exclusive cpusets and its hotplug hooks were
added to this code earlier, when cpusets had only a single lock.
It may well have been fine then.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CPU hotplug locking was quite messy, with a recursive lock to
handle the fact that both the actual up/down sequence wanted to
protect itself from being re-entered, but the callbacks that it
called also tended to want to protect themselves from CPU events.
This splits the lock into two (one to serialize the whole hotplug
sequence, the other to protect against the CPU present bitmaps
changing). The latter still allows recursive usage because some
subsystems (ondemand policy for cpufreq at least) had already gotten
too used to the lax locking, but the locking mistakes are hopefully
now less fundamental, and we now warn about recursive lock usage
when we see it, in the hope that it can be fixed.
[cpufreq] ondemand: make shutdown sequence more robust
Shutting down the ondemand policy was fraught with potential
problems, causing issues for SMP suspend (which wants to hot-
unplug) all but the last CPU.
This should fix at least the worst problems (divide-by-zero
and infinite wait for the workqueue to shut down).
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[TIPC]: Removing useless casts
[IPV4]: Fix nexthop realm dumping for multipath routes
[DUMMY]: Avoid an oops when dummy_init_one() failed
[IFB] After ifb_init_one() failed, i is increased. Decrease
[NET]: Fix reversed error test in netif_tx_trylock
[MAINTAINERS]: Mark LAPB as Oprhan.
[NET]: Conversions from kmalloc+memset to k(z|c)alloc.
[NET]: sun happymeal, little pci cleanup
[IrDA]: Use alloc_skb() in IrDA TX path
[I/OAT]: Remove pci_module_init() from Intel I/OAT DMA engine
[I/OAT]: net/core/user_dma.c should #include <net/netdma.h>
[SCTP]: ADDIP: Don't use an address as source until it is ASCONF-ACKed
[SCTP]: Set chunk->data_accepted only if we are going to accept it.
[SCTP]: Verify all the paths to a peer via heartbeat before using them.
[SCTP]: Unhash the endpoint in sctp_endpoint_free().
[SCTP]: Check for NULL arg to sctp_bucket_destroy().
[PKT_SCHED] netem: Fix slab corruption with netem (2nd try)
[WAN]: Converted synclink drivers to use netif_carrier_*()
[WAN]: Cosmetic changes to N2 and C101 drivers
[WAN]: Added missing netif_dormant_off() to generic HDLC
...
Patrick McHardy [Fri, 21 Jul 2006 22:09:55 +0000 (15:09 -0700)]
[IPV4]: Fix nexthop realm dumping for multipath routes
Routing realms exist per nexthop, but are only returned to userspace
for the first nexthop. This is due to the fact that iproute2 only
allows to set the realm for the first nexthop and the kernel refuses
multipath routes where only a single realm is present.
Dump all realms for multipath routes to enable iproute to correctly
display them.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Fri, 21 Jul 2006 21:56:02 +0000 (14:56 -0700)]
[IFB] After ifb_init_one() failed, i is increased. Decrease
It before entering in the loop for freeing the other ifb devices.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Ortiz [Fri, 21 Jul 2006 21:50:41 +0000 (14:50 -0700)]
[IrDA]: Use alloc_skb() in IrDA TX path
As pointed out by Christoph Hellwig, dev_alloc_skb() is not intended to be
used for allocating TX sk_buff. The IrDA stack was exclusively calling
dev_alloc_skb() on the TX path, and this patch fixes that.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[SCTP]: Unhash the endpoint in sctp_endpoint_free().
This prevents a race between the close of a socket and receive of an
incoming packet.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[PKT_SCHED] netem: Fix slab corruption with netem (2nd try)
CONFIG_DEBUG_SLAB found the following bug:
netem_enqueue() in sch_netem.c gets a pointer inside a slab object:
struct netem_skb_cb *cb = (struct netem_skb_cb *)skb->cb;
But then, the slab object may be freed:
skb = skb_unshare(skb, GFP_ATOMIC)
cb is still pointing inside the freed skb, so here is a patch to
initialize cb later, and make it clear that initializing it sooner
is a bad idea.
[From Stephen Hemminger: leave cb unitialized in order to let gcc
complain in case of use before initialization]
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log