The IIC nodes used the generic compatible properties only.
This causes the driver to fail when using Standard Speed, as the
operational clock is driven by the 104 MHz HP clock:
i2c-sh_mobile e6820000.i2c: timing values out of range: L/H=0x208/0x1bf
i2c-sh_mobile: probe of e6820000.i2c failed with error -22
Add the SoC-specific compatible property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IIC nodes used the generic compatible properties only.
This may cause the driver to fail when using Standard Speed on IIC
masters where the operational clock is driven by the 130 MHz HP clock.
Add the SoC-specific compatible property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: koelsch: fixup I2C2 clock frequency
Current Koelsch I2C2 has 400kHz settings,
but, ak4643 audio codec chip which is connected to I2C2 can't
work such frequency.
Fixup I2C2 clock frequency to 100kHz.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: r8a7779 dtsi: Add SoC-specific SATA compatible property
The SATA node used the generic compatible property only, which was
deprecated by commit e67adb4e669db834 ("sata_rcar: Add R-Car Gen2 SATA
PHY support"). Add the SoC-specific one introduced by that commit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Henninger board, defining the GPIO that the driver
should check when probing (which is the ID output from MAX3355 OTG chip).
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin function/group and prop, moved device node, fixed summary,
added changelog] Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Koelsch board, defining the GPIO that the driver
should check when probing (which is the ID output from MAX3355 OTG chip).
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin function/group and prop, moved device node, fixed summary,
added changelog] Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Lager board, defining the GPIO that the driver
should check when probing. Since this board doesn't have the OTG ID pin, we
assume that GP5_18 (USB0_PWEN) is an ID pin because it is 1 when the SW5 is
in position 2-3 (meaning USB function) and 0 in other positions.
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin node and prop, moved device node, fixed summary, supplemented
changelog] Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Note that there will be pinctrl-related error messages if both
internal PCI and USB3.0 are enabled but they should be just ignored:
sh-pfc e6060000.pfc: pin GP_5_22 already requested by ee0d0000.pci; cannot claim for ee000000.usb
sh-pfc e6060000.pfc: pin-182 (ee000000.usb) status -22
ata1: SATA link down (SStatus 0 SControl 300)
sh-pfc e6060000.pfc: could not request pin 182 (GP_5_22) from group usb2 on device sh-pfc
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Wolfram Sang [Tue, 16 Sep 2014 16:10:37 +0000 (18:10 +0200)]
ARM: shmobile: r8a7790: switch from scif to scifa
SCIF and SCIFA can be plexed onto the same wires on Lager board. The
datasheet also describes the wires as SCIFA. So, to make use of the
bigger FIFOs switch to SCIFA instead.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: dts: Add common file for AA104XD12 panel
The Mitsubishi AA104XD12 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Sun, 26 Oct 2014 14:20:27 +0000 (16:20 +0200)]
ARM: shmobile: Remove FSF address from copyright headers
The information is already included in the COPYING file in the kernel
sources root directory, we don't want to modify all source files when
the FSF will move to a new address, and I'm tired of seeing the related
checkpatch.pl warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rename r8a7790_register_cmt() as r8a73a4_register_cmt() to
reflect name of the SoC in use. The use of r8a7790 appears
to be due to historical sharing of code from that SoC.
Shared code is no longer used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
In addition, this will allow the PM domain code to find the PM domain
for the console device.
Note that we have to keep the "console=ttySC4" parameter in
chosen/bootargs, else we only get console messages on tty0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
In addition, this will allow the PM domain code to find the PM domain
for the console device.
Note that we have to keep the "console=ttySC1" parameter in
chosen/bootargs, else we only get console messages on tty0, and because
this DTS is shared between legacy and multi-platform.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
In addition, this will allow the PM domain code to find the PM domain
for the console device.
Remove the now-superfluous "console=" parameter from chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[horms+renesas@verge.net.au: updated for removal of dma-multiplexer base
address] Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms+renesas@verge.net.au: update for addition of r8a7794-alt.dtb] Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Linus Torvalds [Mon, 20 Oct 2014 00:43:06 +0000 (17:43 -0700)]
Merge tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148, and
basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late"
* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: corrected bcm2835 search
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
MAINTAINERS: Update Santosh Shilimkar's email id
ARM: sunxi_defconfig: enable CONFIG_REGULATOR
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
Linus Torvalds [Sun, 19 Oct 2014 23:25:56 +0000 (16:25 -0700)]
Merge git://git.infradead.org/users/eparis/audit
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...