Merge tag 'samsung-dt-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DeviceTree update for v4.9, second round" from Krzysztof Kozłowski:
1. Enable HDMI on Arndale Octa board.
2. Update list of clocks for FIMC-IS block on Exynos4x12.
3. Remove skeleton.dtsi thus fixing DT compiler warning:
"Node /memory has a reg or ranges property, but no unit name"
This is a tree-wide effort by various people. Javier Martinez Canillas did
it for Exynos and S5PV210.
* tag 'samsung-dt-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5p: Add missing unit name to memory nodes for S5PV210 boards
ARM: dts: s5p: Remove skeleton.dtsi inclusion for S5PV210
ARM: dts: exynos: Add missing unit name to memory nodes in Exynos5 DTS
ARM: dts: exynos: Add missing unit name to memory nodes in Exynos4 DTS
ARM: dts: exynos: Add missing unit name to memory nodes in Exynos3 DTS
ARM: dts: exynos: Remove skeleton.dtsi usage for Exynos5
ARM: dts: exynos: Remove skeleton.dtsi usage for Exynos4
ARM: dts: exynos: Remove skeleton.dtsi usage for Exynos3
ARM: dts: exynos: Add missing memory node for Exynos5440 boards
ARM: dts: exynos: Add all required FIMC-IS clocks to exynos4x12
ARM: dts: exynos: Enable HDMI for Arndale Octa board
Merge tag 'omap-for-v4.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "omap dts updates for v4.9 merge window, part 2" from Tony Lindgren:
Part two of device tree changes for omaps for v4.9 merge window. This
is mostly usability and non-critical fixes except for the addition of
beagleboard-x15 rev B1 support:
- Fix omap4 pandaboard SDIO WLAN latencies in idle mode by enabling wakeirq
- Usability fixes for WLAN, USB, LEDs and power button on omap5 boards
- Remove am57xx beagleboard-x15 pinmux configuration as the processor requires
that it's done in IO isolation in bootloader except for MMC and DCAN
- Add support for beagleboard-x15 rev B1 by moving most of the
configuration to am57xx-beagle-x15-common.dtsi
- Enable support for more than 2GB of memory for omap5 with LPAE with
#address-cells
- Fix omap3-gta04 backlight PWM frequency until the PWM driver
- Revert am335x dts changes related to cpufreq as the driver changes
still have not merged and the dts changes broke cpufreq
* tag 'omap-for-v4.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "ARM: dts: dra7: Move to operating-points-v2 table"
Revert "ARM: dts: am33xx: Move to operating-points-v2 table and ti-cpufreq driver"
Revert "ARM: dts: am335x-boneblack: Enable 1GHz OPP for cpu"
ARM: dts: omap3-gta04: reduce panel backlight PWM frequency to 83Hz
ARM: dts: Add support for more than 2GB of memory for omap5
ARM: dts: am57xx-beagle-x15: Add support for rev B1
ARM: dts: am57xx-beagle-x15: Remove pinmux configurations for erratum i869
ARM: dts: Fix LEDs for igepv5
ARM: dts: Add power button support for igepv5
ARM: dts: Configure omap5 OTG ID pin
ARM: dts: ARM: dts: Fix omap5 SDIO dat1 interrupt
ARM: dts: Configure panda SDIO WLAN wakeirq
Merge tag 'sti-dt-for-v4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt
Pull "STi dts update" from Patrice Chotard:
Update gpio-cells and gpio specifier for STiH415/416
Add PWM capture support for STiH416 and STiH407 family
Add USB3 support for B2260
Add HVA support for STiH410
Add clk_ignore_unused in bootargs of B2260
Add Flexible Direct Memory Access (FDMA) support for STiH407 family
Add internal audio codec IP spport for STiH407 family
Add uniperif player/reader IP blocks for STiH407 family
ARM: dts: STiH410: clock configuration to address 720p and 1080p
It is necessary to properly configure these clocks in order
to address 720p and 1080p HDMI resolution.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Acked-by: Peter Griffin <peter.griffin@linaro.org>
ARM: dts: STi: STiH407: clock configuration to address 720p and 1080p
It is necessary to properly configure these clocks in order
to address 720p and 1080p HDMI resolution.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Acked-by: Peter Griffin <peter.griffin@linaro.org>
Karl Beldan [Thu, 8 Sep 2016 18:33:24 +0000 (11:33 -0700)]
ARM: dts: da850-lcdk: Add NAND to DT
This adds DT support for the NAND connected to the SoC AEMIF.
Passed torture hashing a 40MB file on top of UBIFS using subpages.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
[khilman: add back default partitions from an earlier patch] Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Merge tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DA850 device-tree enhancements include" from Sekhar Nori:
- Support for new board OMAP-L138 LCDK
- Add AEMIF node on DA850 EVM and use it for NAND
- Audio support for LCDK
- Cleanups for PWM and UART
* tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Audio support via simple-card
ARM: dts: da850,da850-evm: Add an aemif node and use it for the NAND
ARM: dts: da850: Add basic DTS for the LCDK
ARM: dts: da850: Add missing pin muxing for the UARTs
ARM: dts: da850: Add new ECAP and EPWM bindings
The original commit updated the cpufreq operating points tables for
dra7xx but was merged before the driver making use of the node was
merged, which breaks the existing cpufreq implementation on the system,
so revert the patch until the ti-cpufreq driver is merged.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
The original commit updated the cpufreq operating points tables for
am33xx but was merged before the driver making use of the node was
merged, which breaks the existing cpufreq implementation on the system,
so revert the patch until the ti-cpufreq driver is merged.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
The original commit updated the cpufreq operating points tables for
am335x-boneblack but was merged before the driver making use of the node
was merged, which breaks the existing cpufreq implementation on the
system, so revert the patch until the ti-cpufreq driver is merged.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge tag 'arm-soc/for-4.9/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM-based Device Tree changes for v4.9,
please pull the following:
- Jon adds support for the Ethernet MAC DT nodes (AMAC) and provides the
following updates for Broadcom references boards:
* New Northstar Plus reference boards added: BCM958525er, BCM958522er,
BCM988312hr, BCM958623hr and BCM958622hr
* Add SATA nodes to the BCM958625hr and XMC boards
* Add I2C nodes to the XMC board
* Fixes the amount of RAM on BCM958625HR, BCM958625K and BCM958525XMC boards
* Add the GPIO reboot method for BCM958625hr and XMC boards
- Dhanajay adds PWM nodes for the Northstar Plus SoCs
- Rafal adds the USB 2.0 PHY to the BCM5301x Device Tree file include
- Stefan adds a missing USB clock to the BCM283x DT files, adds a DTSI file for
the USB host mode on BCM283x and finally documents and adds support for the
Raspberry Pi Zero
- Florian adds support for the Northstar Plus Switch Register Access block which
enables the integrated switch on these SoCs and enables the switch ports on the
BCM958625HR reference board
* tag 'arm-soc/for-4.9/devicetree' of http://github.com/Broadcom/stblinux: (22 commits)
ARM: dts: bcm2835: Add Raspberry Pi Zero
DT: bindings: bcm: Add Raspberry Pi Zero
ARM: dts: bcm283x: Add dtsi for USB host mode
ARM: dts: bcm283x: Add missing USB clock
ARM: dts: NSP: Add new DT file for bcm958622hr
ARM: dts: NSP: Add new DT file for bcm958623hr
ARM: dts: NSP: Add new DT file for bcm988312hr
ARM: dts: NSP: Add new DT file for bcm958522er
ARM: dts: NSP: Add new DT file for bcm958525er
ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file
ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file
ARM: dts: NSP: Specify RAM amount for BCM958525XMC board
ARM: dts: NSP: Specify RAM amount for BCM958625K board
ARM: dts: NSP: Enable SATA and add i2c devices on XMC
ARM: dts: NSP: Enable SATA on bcm958625hr
ARM: dts: NSP: Correct RAM amount for BCM958625HR board
ARM: dts: NSP: Add PWM Support to DT
ARM: BCM5301X: Specify PHY of USB 2.0 in DT
ARM: dts: NSP: Add BCM958625HR switch ports
ARM: dts: NSP: Add Switch Register Access Block node
...
ARM: dts: omap3-gta04: reduce panel backlight PWM frequency to 83Hz
This helps to get 100% intensity closer to "always on".
It compensates for an effect of dmtimer which at 100% still emits short
"off" impulses and the startup-time of the DC/DC converter makes
backlight intensity not reach full scale. The lower the PWM frequency
is, the smaller is this effect.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
[gregory.clement@free-electrons.com:
- extract dt part from "arm: orion5x: Add DT-based support for Netgear
WNR854T"
- squashed "arm: orion5x: Alias uart0 to serial0 for all orion5x" into
this commit and move serial0 alias from dtsi to dts] Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: DT: STi: stihxxx-b2120: Add DT nodes for STi audio card
This patch enables the uniperif players 2 & 3 for b2120 boards
and also adds the "simple-audio-card" device node to interconnect
the SoC sound device and the codec.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: DT: STiH407: Add spdif_out pinctrl config
This patch adds the pinctrl config for the spidf out
pins used by the sasg codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds the pinctrl config for the i2s_in pins
used by the uniperif reader IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds the pinctrl config for the i2s_out pins
used by the uniperif player IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org>
Tony Lindgren [Tue, 13 Sep 2016 23:10:56 +0000 (16:10 -0700)]
ARM: dts: Add support for more than 2GB of memory for omap5
Some omap5 variants have more than 2GB of memory available as
optional models. Let's update the dts files to use two address
cells similar to what dra7 is using with commit dae320ec3173
("ARM: dts: DRA7: change address-cells and size-cells").
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am57xx-beagle-x15: Add support for rev B1
Latest update to the BeagleBoard-X15 platform (revision B1)[1] updates
for allowing UHS SD cards to function with the split of supply to SD
card from a dedicated LDO.
As a result of this, AM57xx BeagleBoard-X15 now uses gpio2_30 instead
of gpio6_28 for HDMI because HDMI_LS_OE should now be switched from
GPIO6_28(Y9) to GPIO2_30 (AG8) to avoid a 1.8V GPIO toggling a 3.3V
SoC input when the SD card is in UHS 1.8V mode.
NOTE: For UHS mode to function, we need full fledged IODelay support
in kernel to be functional. IODelay support is yet to be added.
Further, It does not make much sense to spin off a new board
compatible flag since there is no real functional benefit for the
same.
Note: Even though production version is supposed to be B1, there is
over ~200 boards of previous version (A2)[2] out there which continue
to get supported with the existing dts file (to maintain compatibility
with existing bootloaders for A2) and the production board is now
supported as revb1.
ARM: dts: am57xx-beagle-x15: Remove pinmux configurations for erratum i869
Pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due
to the limitations introduced by erratum ID: i869[1] (IO Glitches
can occur when changing IO settings) and elaborated in the Technical
Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
Only peripheral that is permitted for dynamic pin mux configuration
is MMC and DCAN. MMC is permitted to change to accommodate the
requirements for varied speeds (which require IO-delay support in
kernel as well). DCAN is a result of i893[1] (DCAN initialization
sequence). However, since we don't use DCAN on X15, with the exception
of MMC, all other pin mux configurations are removed from the dts.
Tony Lindgren [Fri, 9 Sep 2016 21:04:28 +0000 (14:04 -0700)]
ARM: dts: Configure omap5 OTG ID pin
The ID pin GPIO comes from the PMIC. Let's configure it as a GPIO
for the driver to use, and also make sure the PMIC GPIO pin muxing
is correct. The PMIC pad1 and 2 values for omap5-uevm and igepv5 are
0x5a and 0x1b, we only need to clear bit 2 in pad1 register to make
the ID pin GPIO work.
Merge tag 'clcd-nomadik' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "CLCD graphics on the Nomadik NHK15" from Linus Walleij:
* tag 'clcd-nomadik' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: add the CLCD LCD display to the NHK15
ARM: dts: add PMU to the NHK15 device tree
ARM: nomadik: select MFD_SYSCON
dt-bindings: Add TPO TPG110 binding
dt-bindings: add vendor TPO
ARM: dts: add STMPE PWM to the NHK15 device tree
Merge tag 'imx-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree changes for 4.9" from Shawn Guo:
- Add SoC support for i.MX7 Solo which is a reduced version of i.MX7
Dual.
- New board support: Gateworks Ventana i.MX6Q/DL GW553x, Inverse Path
i.MX53 USB armory, i.MX6Q/DL TS-4900 from Technologic Systems,
i.MX6UL GEA M6UL modules from Engicam, i.MX7 Solo Warp7 board.
- Add DMA and IPU CSI devices for i.MX53 SoC support.
- Refine i.MX7 Dual SoC DTS as a preparation of i.MX7 Solo support.
- Use of_graph dt nodes to describe the panel for vf610-colibri and
ls1021a-twr boards.
- Add gpio-ranges property to i.MX6 GPIO controllers, which will be
useful when GPIO driver is changed to request pad configuration as
GPIO function.
- Random device additions or small changes for various board support.
* tag 'imx-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
ARM: dts: add gpio-ranges property to iMX GPIO controllers
ARM: dts: imx35: add iim module to imx35.dtsi
ARM: dts: vf610-colibri: use of_graph dt nodes to describe the panel
ARM: dts: ls1021a: Add of_graph dt nodes to describe the panel
ARM: dts: imx53: add support for USB armory board
devicetree: Add vendor prefix for Inverse Path
ARM: dts: imx7s-warp: Add Bluetooth support
ARM: dts: imx7s-warp: Add User Button support
ARM: dts: imx7s-warp: Enable I2C2 device support
ARM: dts: imx6ul-geam: Add Engicam IMX6UL GEA M6UL initial support
ARM: dts: imx6ul iomuxc syscon is compatible to imx6q
ARM: dts: imx7-colibri: add Audio support
ARM: dts: imx7-colibri: add basic supply regulators
ARM: dts: imx7-colibri: move SD-card to module level
ARM: dts: imx6sx: Add GPU bindings
ARM: dts: imx7s-warp: Let the codec control MCLK pinctrl
ARM: dts: imx6ul-pico-hobbit: Use WDOG_B pin reset
ARM: dts: imx6q-bx50v3: configure unused pca953x pins
ARM: dts: imx6sx: document SION necessity of ENET1_REF_CLK1
ARM: dts: imx7s-warp: Use WDOG_B pin reset
...
Merge tag 'tegra-for-4.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "ARM: tegra: Device tree changes for v4.9-rc1" from Thierry Reding:
Contains a couple of cleanups for Tegra114 device trees.
* tag 'tegra-for-4.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Correct polarity for Tegra114 PMIC interrupt
ARM: tegra: Fix Tegra114 USB compatible values
Merge tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.9" from Heiko Stübner:
32bit Rockchip devicetree changes containing two new rk3288 boards (Fennec
and Firefly-reload), display support for the rk3288-evb, support for the
recently added firmware reboot-flag support and some housekeeping cleanups.
* tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add sensor-supplies on PopMetal-RK3288 board
ARM: dts: rockchip: fix L3G4200D i2c address on PopMetal-RK3288 board
ARM: dts: rockchip: enable usbotg for Popemtal-rk3288 board
ARM: dts: rockchip: add missing regulators for firefly reload board
ARM: dts: rockchip: remove excess sd properties from firefly reload
ARM: dts: rockchip: add syscon-reboot-mode DT node
soc: rockchip: add reboot-mode header
ARM: dts: rockchip: move rk3288 usbphy under the GRF node
ARM: dts: rockchip: add rk3288-firefly-reload
ARM: dts: rockchip: add dts for RK3288-Fennec boards
ARM: dts: rockchip: add the panel power supply for rk3288-evb board with rk808 pmu
ARM: dts: rockchip: add the panel power supply for rk3288-evb board with act8846 pmu
ARM: dts: rockchip: add eDP/panel display device nodes for rk3288-evb
Merge tag 'sunxi-dt-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.9" from Maxime Ripard:
Business as usual on our side, with a mix of new boards and new IPs enabled
on boards:
- Support for the GPIO found on the AXP PMIC
- ESP8089 on the relevant boards
- More boards converted to the reference design and q8 designs
- New boards: Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange
Pi Lite, Olimex A33-Olinuxino, Empire Electronix M712, inet-d978_rev2,
Nano Pi Neo
* tag 'sunxi-dt-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (31 commits)
devicetree: Add vendor prefix for FriendlyARM
ARM: dts: sun8i: Add dts file for the NanoPi NEO SBC
ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers
ARM: dts: sun8i: Add dts file for the Orange Pi Plus2E SBC
ARM: dts: sun8i: Orange Pi Plus dts is for the Plus and Plus 2
ARM: dts: sun8i: Add PWM controller node in H3
ARM: dts: sun8i: Add dts file for inet-d978_rev2 tablets
ARM: dts: sun9i: Add missing #interrupt-cells to R_PIO pinctrl device node
ARM: dts: sun8i: Rename reference-design-tablet touchscreen node
ARM: dts: sun5i: Add dts file for the Empire Electronix M712 tablet
ARM: dts: sun5i: Convert inet-98v-rev2 dts to use reference-design-tablet.dtsi
ARM: dts: sun4i: Disable ohci1 on ba10-tv-box
ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2809
ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2407
ARM: dts: sun8i: add NAND controller node for A23/A33
ARM: dts: sun6i: Add new dts file for tablets using the inet-q972 PCB
ARM: dts: sun6i: Add sun6i-reference-design-tablet.dtsi
ARM: dts: sun6i: colorfly-e708-q1: Remove unused mma8452_int_e708_q1 node
ARM: dts: sun9i: Switch to the AC100 RTC clock outputs for osc32k
ARM: dts: sun9i: cubieboard4: Add device node for AC100
...
Clean-up:
* Remove obsolete vsp1 properties from r8a779[01] SoCs
New boards:
* Add r8a7792/wheat and r7s72100/rskrza1 boards
Enablement:
* Enable LEDs, DU, SDHI on r8a7792/blanche board
* Enable MMCIF and SDHI on r8a7794/alt board
* Add SPI and VSP1 to r8a7792 SoC
* Add ethernet to r7s72100 SoC
* tag 'renesas-dt2-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits)
ARM: dts: wheat: add support for tactile switches
ARM: dts: wheat: add QSPI support
ARM: dts: r8a7792: add QSPI support
ARM: dts: r8a7792: add QSPI clock
ARM: dts: wheat: add SDHI0 support
ARM: dts: wheat: add CAN support
ARM: dts: r8a7794: fix PWM clock parent
ARM: dts: rskrza1: add ethernet DT support
ARM: dts: r7s72100: add ethernet to device tree
ARM: dts: r7s72100: add ethernet clock to device tree
ARM: dts: rskrza1: initial device tree
ARM: dts: Add RSKRZA1 DT bindings documentation
ARM: dts: wheat: add Ethernet support
ARM: dts: wheat: initial device tree
ARM: dts: document Wheat board
ARM: dts: blanche: add support for general purpose LEDs
ARM: dts: r8a7792: add VSP1V support
ARM: dts: r8a7792: add VSP1V clocks
ARM: dts: blanche: add DU support
ARM: dts: blanche: add SDHI0 support
...
Merge tag 'lpc18xx_dts_for_4.9_part2' of https://github.com/manabian/linux-lpc into next/dt
Pull "Device Tree clean up for LPC18xx platform" from Joachim Eastwood:
* Removal of skeleton.dtsi from the common armv7-m dtsi together
with lpc18xx and efm32 platforms.
* Fix for unit address warnings from the dtc on lpc18xx/efm32.
That is made possible with skeleton.dtsi gone.
* tag 'lpc18xx_dts_for_4.9_part2' of https://github.com/manabian/linux-lpc:
ARM: dts: efm32: remove skeleton.dtsi include and fix unit address warnings
ARM: dts: lpc18xx: remove skeleton.dtsi include and fix unit address warnings
ARM: dts: armv7-m: remove skeleton.dtsi include
Merge tag 'mvebu-dt-4.9-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.9 (part 1)" from Gregory CLEMENT:
- update for Armada XP/38x allowing using direct access SPI
- various improvement for Armada 39x platforms
- add pinctrl information for NANd on Armada 38x
- fix the kirkwood based Openblock A6 external GPIO pins
* tag 'mvebu-dt-4.9-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: fix reference to a390 spi controller
ARM: dts: armada-38x: Add NAND pinctrl information
ARM: dts: kirkwood: Fix Openblock A6 external GPIO pins
ARM: dts: mvebu: armada-395-gp: add support for the Armada 395 GP Board
ARM: dts: mvebu: armada-390-db: add support for the Armada 390 DB board
ARM: dts: mvebu: armada-398-db: enable supported usb interfaces
ARM: dts: mvebu: armada-398: update the dtsi about missing interfaces
ARM: dts: mvebu: armada-395: add support for the Armada 395 SoC family
ARM: dts: mvebu: armada-39x: enable rtc for all Armada-39x SoCs
ARM: dts: mvebu: armada-39x: add missing nodes describing GPIO's
ARM: dts: mvebu: armada-39x: enable watchdog for all Armada-39x SoCs
ARM: dts: mvebu: armada-39x: enable the thermal sensor in Armada-39x SoCs
ARM: dts: mvebu: armada-39x: enable PMU, CA9 SoC Controller and Coherency fabric
ARM: dts: mvebu: armada-39x: update the SDHCI node on Armada 39x
ARM: dts: mvebu: armada-390: add missing compatibility string and bracket
ARM: dts: mvebu: a385-db-ap: add default partition description for NAND
ARM: dts: mvebu: a385-db-ap: enable USB (orion-ehci) port
ARM: dts: mvebu: armada-370-xp: Add MBus mappings for all SPI devices
ARM: dts: mvebu: A37x/XP/38x/39x: Move SPI controller nodes into 'soc' node
ARM: dts: mvebu: Add SPI1 pinctrl defines for Armada XP
Mark Rutland [Fri, 2 Sep 2016 16:34:50 +0000 (17:34 +0100)]
ARM: dts: explicitly mark skeleton.dtsi as deprecated
As noted in commit 3ebee5a2e141496b ("arm64: dts: kill skeleton.dtsi"),
there are a number of problems with skeleton.dtsi, and it would be
prefereable to remove it entirely. As there are a large number of
existing users, fixing these up will take a while.
This patch adds a note to arm's skeleton.dtsi noting that this is the
case, to make this more obvious and hopefully minimize new uptake of
skeleton.dtsi in the mean time.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Rob Herring <robh@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Olof Johansson <olof@lixom.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge tag 'sti-dt-for-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt
Pull "STi dts fixes and new STi 96board support" from Patrice Chotard:
Add thermal node for STiH407 family boards
Add specific nodes for STMicroelectronics 96Board
Add new B2260 STi board file = 96Board
Fix ahci issue on STiH407 family
Fix debugfs/pinctrl kernel warning
Update gpio-cells and gpio specifier
Merge tag 'omap-for-v4.9/dt-pt1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "DTS related changes for omaps for v4.9 merge window" from Tony Lindgren:
- Update elm phandle for am335x
- Fix overo NAND gpmc ranges, this has always been broken so it can
wait for the merge window
- Fix NAND and use NAND ready pin for logicpd gpmc, this can wait too
as it's been using the older configration since the dts got added
- A series of dtc warning fixes for unit names
- Keep dcdc3, 5 and 6 enabled during suspend on am347x boards
- Disable DDR regulator during rtc-only/poweroff mode for am437x boards
- Remove redundant regulator compatibles for am437x boards
- Increas QSPI max frequency for dra7 boards
- Enable QSPI for am57xx-idk-common
- Enable am335x-wega audio support
- Workaround for i845 for dra7
- Update binding for logicpd boards
- Add gpio-decoder nodes for am335x-icev2 board
- Add linux,pci-domain property for dra7
- Fix dra7 clock data gmac_gmii_ref_clk_div and related clock tree
entries, these can wait for merge window as Ethernet works on dra7
- A series of changes to drop skeleton.dtsi because of dtc warnings
* tag 'omap-for-v4.9/dt-pt1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (54 commits)
ARM: dts: dra7: Add missing unit name to memory nodes
ARM: dts: dra62x: Add missing unit name to memory nodes
ARM: dts: dm8168: Add missing unit name to memory nodes
ARM: dts: dm8148: Add missing unit name to memory nodes
ARM: dts: am572x: Add missing unit name to memory nodes
ARM: dts: am4372: Add missing unit name to memory nodes
ARM: dts: am3517: Add missing unit name to memory nodes
ARM: dts: am335x: Add missing unit name to memory nodes
ARM: dts: omap5: Add missing unit name to memory nodes
ARM: dts: omap4: Add missing unit name to memory nodes
ARM: dts: omap3: Add missing unit name to memory nodes
ARM: dts: omap2: Add missing unit name to memory nodes
ARM: dts: am4372: Remove skeleton.dtsi usage
ARM: dts: dra7: Remove skeleton.dtsi usage
ARM: dts: dm816x: Remove skeleton.dtsi usage
ARM: dts: dm814x: Remove skeleton.dtsi usage
ARM: dts: am33xx: Remove skeleton.dtsi usage
ARM: dts: omap5: Remove skeleton.dtsi usage
ARM: dts: omap4: Remove skeleton.dtsi usage
ARM: dts: omap3: Remove skeleton.dtsi usage
...
Merge tag 'uniphier-dt-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
Merge "UniPhier ARM SoC DT updates for v4.9" from Masahiro Yamada:
* Match DT names other projects and documents
* Switch over to PSCI
* Use clock/reset drivers
* Misc
* tag 'uniphier-dt-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add specific compatible to SoC-Glue node
ARM: dts: uniphier: use clock/reset controllers
ARM: dts: uniphier: switch over to PSCI
ARM: dts: uniphier: match DT names to other projects and documents
ARM: dts: uniphier: remove a whitespace after tabs
Merge tag 'samsung-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Samsung DeviceTree update for v4.9" from Krzysztof Kozlowski:
1. Set chosen serial bitrate which allows proper serial output when
bootloader does pass all the data in command line.
2. Cleanup.
* tag 'samsung-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use 'hpd-gpios' instead of 'hpd-gpio'
ARM: dts: exynos: Use stdout non-deprecated property and add serial options to Odroid XU/XU3/XU4
Merge tag 'lpc18xx_dts_for_4.9' of https://github.com/manabian/linux-lpc into next/dt
Merge "Device Tree additions for LPC18xx platform" from Joachim Eastwood:
Small fix for the compatible string for the NXP SE97 I2C chip on the
Hitex Eval board from Guenter and a couple of additional DT properties
for the DWMAC that is need for correct operation.
* tag 'lpc18xx_dts_for_4.9' of https://github.com/manabian/linux-lpc:
ARM: dts: lpc18xx: configure dwmac properly
ARM: dts: lpc4350-hitex-eval: fix binding for SE97 i2c device
Merge tag 'renesas-dt-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.9" from Simon Horman:
* Add DU, VIN, I2C, SDHI, EtherAVB, GPIO support to r8a7792
* Enable CAN0 on r8a7792/blanche
* Enable sound on r8a7794/silk
* Correct SDHI register size on r8a7794
* tag 'renesas-dt-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits)
ARM: dts: r8a7792: add DU support
ARM: dts: r8a7792: add DU clocks
ARM: dts: r8a7792: fix misindented line
ARM: dts: silk: add sound support
ARM: dts: r8a7794: add sound support
ARM: dts: r8a7794: add Audio-DMAC support
ARM: dts: r8a7794: add MSTP10 clocks
ARM: dts: r8a7794: add MSTP5 clocks
ARM: dts: r8a7794: add audio clocks
ARM: dts: r8a7792: add VIN support
ARM: dts: r8a7792: add VIN clocks
ARM: dts: r8a7792: add I2C support
ARM: dts: r8a7792: add I2C clocks
ARM: dts: r8a7792: add SDHI support
ARM: dts: r8a7792: add SD clocks
ARM: dts: r8a7794: Correct SDHI register size
ARM: dts: blanche: add CAN0 support
ARM: dts: r8a7792: add CAN support
ARM: dts: r8a7792: add CAN clocks
ARM: dts: r8a7792: add EtherAVB support
...
Linus Walleij [Sun, 10 Jan 2016 21:32:43 +0000 (22:32 +0100)]
ARM: dts: add PMU to the NHK15 device tree
The so-called Nomadik Power Mangament Unit is actually a set
of some power management registers and some miscellaneous
system control stuff like muxing of entire hardware units.
Add this as a system controller.
There used to be two versions of the RealView EB 11MPCore:
- arm-realview-eb-11mp.dts: the most common variant supported by
QEMU with the revision C core tile
- arm-realview-eb-revb.dts: for the variant with the elder revision
B core tile.
As it turns out that there are also a few variants of the
baseboard, unrelated to the coretile, and that these can of
course be mounted on top of each other in all permutations, we
create:
- arm-realview-eb-11mp.dts: the most common variant supported by
QEMU with the pre-revision D baseboard and the revision C core
tile.
- arm-realview-eb-11mp-bbrevd.dts: the revision D baseboard
with the common revision C core tile.
- arm-realview-eb-11mp-ctrevb.dts: the pre-revision D baseboard
with the revision B core tile.
- arm-realview-eb-11mp-bbrevd-ctrevb.dts: the revision D baseboard
with the revision B core time.
Or as a table:
| Core tile: C | Core tile: B
-----------+----------------------------+-----------------------------------
Baseboard: | |
pre-D |arm-realvie-eb-11mp | arm-realview-eb-11mp-ctrevb
-----------+----------------------------+-----------------------------------
Baseboard: | |
D |arm-realview-eb-11mp-bbrevd | arm-realview-eb-11mp-bbrevd-ctrevb
-----------+----------------------------+-----------------------------------
ARM: dts: add device tree for the RealView EB Rev D
The RealView EB baseboard revision D is a special case as it appears
to be undocumented in ARM official documents, while the Linux kernel
still contains special code for handling it.
commit be4f3c8691492934c8ee03dbecb3a3a865ac6cd6
"Add RealView/EB support for the LAN9118 Ethernet chip"
adds support for the SMSC LAN9118 chip used on the D revision of
the baseboard, but no other traces of hardware deviations for this
variant can be found.
This creates a separate top-level .dts file especially for this
board version, so that it gets registered with the right type
of ethernet controller. The ethernet controller modifications
are then put into a separate .dtsi file so it can be overlaid
on other EB variants using the revision D baseboard.
The ethernet version in the earlier RealView EB variants is
LAN91C111 and not LAN9118 according to ARM DUI 0303E
"RealView Emulation Baseboard User Guide" page 3-57.
Make sure that this is used for the base variant of the board.
As the DT bindings for LAN91C111 does not specify any power
supplies, these need to be deleted from the DTS file.
Fixes: 2440d29d2ae2 ("ARM: dts: realview: support all the RealView EB board variants") Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM: dts: add gpio-ranges property to iMX GPIO controllers
To establish a connection between GPIO controllers and pin multiplexor
controller add gpio-ranges properties to all GPIO controllers found
on iMX50, iMX6Q/D, iMX6DL/S, iMX6SL, iMX6SX, iMX6UL and iMX7D/S
SoCs. The change was done after human parsing of output from
Stefan Agner [Tue, 6 Sep 2016 18:46:57 +0000 (11:46 -0700)]
ARM: dts: vf610-colibri: use of_graph dt nodes to describe the panel
The fsl,panel property is deprecated and we should use the new
of_graph dt bindings to describe the relationship between the DCU
controller and the panel.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Joachim Eastwood [Mon, 29 Aug 2016 21:58:29 +0000 (23:58 +0200)]
ARM: dts: efm32: remove skeleton.dtsi include and fix unit address warnings
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes. Also add missing
device_type to the memory node while at it.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Joachim Eastwood [Mon, 29 Aug 2016 21:37:24 +0000 (23:37 +0200)]
ARM: dts: lpc18xx: remove skeleton.dtsi include and fix unit address warnings
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Acked-by: Rob Herring <robh@kernel.org>
Joachim Eastwood [Mon, 29 Aug 2016 21:33:56 +0000 (23:33 +0200)]
ARM: dts: armv7-m: remove skeleton.dtsi include
Remove skeleton.dtsi from the common ARM Cortex-M dtsi. This will allow
us to remove skeleton.dtsi on a per platform basis and get rid of the
unit address warning on the memory nodes without getting duplicate memory
nodes.
See 3ebee5a2e141 ("arm64: dts: kill skeleton.dtsi") for additional
reasons not to use the skeleton.dtsi.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Vladimir Murzin <vladimir.murzin@arm.com> Acked-by: Stefan Agner <stefan@agner.ch> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>