bcma: add PCI id 0x4313

This PCI id is used by some BCM4313 cards without a sprom. I have seen
such a card on a router connected to some BCM63XX SoC via PCIe. There
are cards out there with the same PCI id and a BCM4311, which is a pre
ieee80211n chip only supporting ieee80211a, these are still not
supported by b43 and not detected by ssb.

This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: reject PCI cards in bcma.

bcma currently only supports PCIe cards and no PCI cards, reject them
if we find them. I have never heard of any PCI card using the AI bus
(bcma), all of them are using ssb instead.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: wireless: wl1251: update firmware path

TI firmwares are located under ti-connectivity
directory. Update path to make sure driver can
find and load firmware blob.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00_pci: Fix interrupt handler name (visible at /proc/interrupts)

Currently driver name is wrong. PCI device address is visible at
/proc/interrupts instead of the name:

 43:    124      0      0      0   PCI-MSI-edge    rtsx_pci
 44:    384      0      0      0   PCI-MSI-edge    snd_hda_intel
 45:  25096      0      0      0   PCI-MSI-edge    0000:01:00.0
                                                   ^^^^^^^^^^^^

So, pass the right name. rt2x00_ops->name contains KBUILD_MODNAME
and good for that, so pass it.

Handler names will be "rt2500pci", "rt2500pci" etc.

Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
CC: Ivo van Doorn <IvDoorn@gmail.com>
CC: Gertjan van Wingerde <gwingerde@gmail.com>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
CC: linux-wireless@vger.kernel.org
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware

This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So
far WCN3660/WCN3680 is available only on MSM platform.

Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS

Wiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xx

A lot people made a contribution to this driver. Here is the list in
alphabetical order:

Eugene Krasnikov <k.eugene.e@gmail.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Olof Johansson <dev@skyshaper.net>
Pontus Fuchs <pontus.fuchs@gmail.com>
Yanbo Li <yanbol@qti.qualcomm.com>

Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: Change variable type to bool

The variables cancel_scan_cmd, enable_data, hs_activate and valid are
only assigned the values true and false. Change its type to bool.

The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):

@exists@
type T;
identifier b;
@@
- T
+ bool
  b = ...;
  ... when any
  b = \(true\|false\)

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

wireless: rt2x00: rt2800usb: add new devices

0411,0241  RT5572  BUFFALO WI-U2-300D Wireless LAN Adapter
0789,0170  RT3572  Logitec LAN-W300AN/U2
0846,9013  RT3573  NETGEAR Adaptador USB Inalambrico Movistar
0df6,006e  RT3573  Sitecom WiFi USB adapter N900
2001,3c1f  RT3573  D-Link DWA-162 Wireless N900 Dual Band Adapter
2001,3c20  RT5372  D-Link DWA-140 Wireless N USB Adapter(rev.D)
2001,3c21  RT5572  D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C)
2001,3c22  RT5372  D-Link DWA-132 Wireless N USB Adapter(rev.B)
2001,3c23  RT5372  D-Link GO-USB-N300 Wireless N Easy USB Adapter
2019,ab29  ?       Planex GW-USMirco300
20f4,724a  RT5572  TRENDnet N600 Wireless Dual Band USB Adapter

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: Convert driver to use new rtl_phy_scan_operation_backup() routine

Now that rtl_phy_scan_operation_backup() exists, convert rtl8188ee to use it.
Routine rtl88e_phy_scan_operation_backup() is no longer used and is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8723ae: Convert driver to use new rtl_phy_scan_operation_backup() routine

Now that rtl_phy_scan_operation_backup() exists, convert rtl8723ae to use it.
Routine rtl8723ae_phy_scan_operation_backup() is no longer used and is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192ce: Convert driver to use new rtl_phy_scan_operation_backup() routine

Now that rtl_phy_scan_operation_backup() exists, convert rtl8192de to use it.
Routine rtl92d_phy_scan_operation_backup() is no longer used and is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: Remove rtl8192c_phy_scan_operation_backup()

Drivers rtl8192ce and rtl8192cu no longer rely on this routine. It is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192ce: Convert driver to use new rtl_phy_scan_operation_backup() routine

Now that rtl_phy_scan_operation_backup() exists, convert rtl8192ce to use it.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Convert to use new rtl_phy_scan_operation_backup() routine

Now that the routine exists in driver rtlwifi, convert rtl8192cu to use it.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Implement a common rtl_phy_scan_operation_backup() routine

Several of the drivers supported by rtlwifi individually implement the same
routine that supports scans. As a first step, create this routine in
driver rtlwifi.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Remove all remaining references to variable 'noise' in rtl_stats struct

This completes removal of all places that reference variable 'noise'
in the rtl_stats struct. The definition of the struct is unchanged.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8188ee: Fix smatch warning in rtl8188ee/hw.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8188ee/hw.c
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code.

This info message is the result of a real error due to a missing break statement
in a "while (1)" loop.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.10+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix smatch warnings in usb.c

Smatch displays the following:
  CHECK   drivers/net/wireless/rtlwifi/usb.c
drivers/net/wireless/rtlwifi/usb.c:458 _rtl_usb_rx_process_agg() warn: assigning (-98) to unsigned variable 'stats.noise'
drivers/net/wireless/rtlwifi/usb.c:503 _rtl_usb_rx_process_noagg() warn: assigning (-98) to unsigned variable 'stats.noise'
drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code.

The variable 'stats.noise' is not used, thus the initializers are removed.
The unreachable code info is fixed by including the appropriate section inside
#ifdef .. #endif constructions.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix smatch warning in pci.c

Smatch reports the following:
  CHECK   drivers/net/wireless/rtlwifi/pci.c
drivers/net/wireless/rtlwifi/pci.c:739 _rtl_pci_rx_interrupt() warn: assigning (-98) to unsigned variable 'stats.noise'

The variable 'stats.noise' is not used. That initializer is removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192_common: Fix smatch errors and warnings in rtl8192c/dm_common.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:551 rtl92c_dm_pwdb_monitor() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:551 rtl92c_dm_pwdb_monitor() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:870 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:870 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:882 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:883 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:891 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:892 rtl92c_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'txpwr_level' 2 <= 2

The unreachable code message is fixed by deleting the code that follows a return.

The errors are fixed by increasing the size of txpwr_level.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Fix smatch warning in rtl8192cu/trx.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8192cu/trx.c
drivers/net/wireless/rtlwifi/rtl8192cu/trx.c:367 _rtl_rx_process() warn: assigning (-98) to unsigned variable 'stats.noise'

This variable is unused, thus the initializer is removed, as well as a
comment referring to that variable.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Fix smatch warnings in rtl8192de/hw.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8192de/hw.c
drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code.

The dead code is deleted.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192du: Fix smatch errors in /rtl8192de/dm.c

Smatch lists the following:
  CHECK   drivers/net/wireless/rtlwifi/rtl8192de/dm.c
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1054 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'ofdm_index' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1056 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'ofdm_index' 2 <= 2
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1126 rtl92d_dm_txpower_tracking_callback_thermalmeter() debug: remove_pools: nr_children over 4000 (4596). (rtlpriv->dbg.global_debuglevel merged)
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1126 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1129 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1132 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1135 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1138 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1141 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1144 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1147 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch1ch13' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1151 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1154 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1157 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1160 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1163 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1166 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1169 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255
drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1172 rtl92d_dm_txpower_tracking_callback_thermalmeter() error: buffer overflow 'cckswing_table_ch14' 33 <= 255

This patch fixes several off-by-one errors. It also removes a comment
referencing variable 'noise' in the rts_stats struct.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: add support for radio chip RF3070

Add support for new RF chip ID: 3070. It seems to be the same as 5370,
maybe vendor just put wrong value on the eeprom, but add this id anyway
since devices with it showed on the marked.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: rework rx path bus interface

The brcmfmac has common and bus specific part. The rx function api
was using sk_buff_head. Changed to sk_buff instead.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Use fw filename and nvram based of devid for sdio.

SDIO firmware download routines uses one name for firmware file
and nvram file for all sdio devices. This is not user friendly.
Use fw filename and nvram filename based upon chip id and revision.

Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix sparse error 'bad constant expression'

The definition of BRCMF_EVENTING_MASK_LEN results in a sparse
error message

.../fweh.c:331:22: error: bad constant expression
.../fweh.c:388:22: error: bad constant expression
.../dhd_common.c:256:22: error: bad constant expression

This is caused by the use of roundup() in BRCMF_EVENTING_MASK_LEN
and it is used to allocate an array variable on the stack. Better
use DIV_ROUND_UP() macro.

Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: reserve memory for bus layer in sk_buff::cb

Bus layer need to share sk_buff::cb with firmware signal feature. Reserve
necessary memory so they won't overwrite each other.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add valid core index check in related functions

Perform a valid check for core index to avoid illegal address access.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add BCM4339 SDIO interface support

BCM4339 is an a/b/g/n/ac 1x1 WiFi chip. This patch adds support for it through
SDIO interface.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: sync firmware event list

Update event list to keep sync with firmware development. Use calculated event
mask length instead of hard-coded value.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Merge tag 'for-linville-20131001' of git://github.com/kvalo/ath

Merge branch 'for-linville' of git://git.kernel.org/pub/scm/linux/kernel/git/luca/wl12xx

Bluetooth: Only one command per L2CAP LE signalling is supported

The Bluetooth specification makes it clear that only one command
should be present in the L2CAP LE signalling packet. So tighten
the checks here and restrict it to exactly one command.

This is different from L2CAP BR/EDR signalling where multiple
commands can be part of the same packet.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Check minimum length of SMP packets

When SMP packets are received, make sure they contain at least 1 byte
header for the opcode. If not, drop the packet and disconnect the link.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Drop packets on ATT fixed channel on BR/EDR

The ATT fixed channel is only valid when using LE connections. On
BR/EDR it is required to go through L2CAP connection oriented
channel for ATT.

Drop ATT packets when they are received on a BR/EDR connection.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: L2CAP connectionless channels are only valid for BR/EDR

When receiving connectionless packets on a LE connection, just drop
the packet. There is no concept of connectionless channels for LE.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: SMP packets are only valid on LE connections

When receiving SMP packets on a BR/EDR connection, then just drop
the packet and do not try to process it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Don't copy L2CAP LE signalling to raw sockets

The L2CAP raw sockets are only used for BR/EDR signalling. Packets
on LE links should not be forwarded there.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix switch statement order for L2CAP fixed channels

The switch statement for the various L2CAP fixed channel handlers
is not really ordered.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Allow changing device class when BR/EDR is disabled

Changing the device class when BR/EDR is disabled has no visible
effect for remote devices. However to simplify the logic allow it
as long as the controller supports BR/EDR operations.

If it is not allowed, then the overall logic becomes rather
complicated since the class of device values would need clearing
or restoring when BR/EDR setting changes.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Restrict loading of long term keys to LE capable controllers

Loading long term keys into a BR/EDR only controller make no sense.
The kernel would never use any of these keys. So instead of allowing
userspace to waste memory, reject such operation with a not supported
error message.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Restrict loading of link keys to BR/EDR capable controllers

Loading link keys into a LE only controller make no sense. The kernel
would never use any of these keys. So instead of allowing userspace
to waste memory, reject such operation with a not supported error
message.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Allow setting static address even if LE is disabled

Setting the static address does not depend on LE beeing enabled. It
only depends on a controller with LE support.

When depending on LE enabled this command becomes really complicated
since in case LE gets disabled, it would be required to clear the
static address and also its random address representation inside
the controller. With future support for private addresses such
complex setup should be avoided.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Restrict SSP setting changes to BR/EDR enabled controllers

Only when BR/EDR is supported and enabled, allow changing of the SSP
setting. Just checking if the hardware supports SSP is not enough
since it might be the case that BR/EDR is disabled.

In the case that BR/EDR is disabled, but SSP supported by the
controller the not supported error message is now returned.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix memory leak with L2CAP signal channels

The wrong type of L2CAP signalling packets on the wrong type of
either BR/EDR or LE links need to be dropped. When that happens
the packet is dropped, but the memory not freed. So actually
free the memory as well.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add the definition for Slave Page Response Timeout

The Slave Page Response Timeout event indicates to the Host that a
slave page response timeout has occurred in the BR/EDR Controller.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 110

"7.7.72 Slave Page Response Timeout Event [New Section]
...
Note: this event will be generated if the slave BR/EDR Controller
responds to a page but does not receive the master FHS packet
(see Baseband, Section 8.3.3) within pagerespTO.

Event Parameters: NONE"

Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add the definition and stcuture for Sync Train Complete

The Synchronization Train Complete event indicates that the Start
Synchronization Train command has completed.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 103

"7.7.67 Synchronization Train Complete Event [New Section]
...

Event Parameters:

Status 0x00       Start Synchronization Train command completed
                  successfully.
       0x01-0xFF  Start Synchronization Train command failed.
                  See Part D, Error Codes, for error codes and
                  descriptions."

Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add the definition for Start Synchronization Train

The Start_Synchronization_Train command controls the Synchronization
Train functionality in the BR/EDR Controller.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 86

"7.1.51 Start Synchronization Train Command [New Section]
...
If connectionless slave broadcast mode is not enabled, the Command
Disallowed (0x0C) error code shall be returned. After receiving this
command and returning a Command Status event, the Baseband starts
attempting to send synchronization train packets containing information
related to the enabled Connectionless Slave Broadcast packet timing.

Note: The AFH_Channel_Map used in the synchronization train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.

The synchronization train packets will be sent using the parameters
specified by the latest Write_Synchronization_Train_Parameters command.
The Synchronization Train will continue until synchronization_trainTO
slots (as specified in the last Write_Synchronization_Train command)
have passed or until the Host disables the Connectionless Slave Broadcast
logical transport."

Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add the definition and structure for Set CSB

he Set_Connectionless_Slave_Broadcast command controls the
Connectionless Slave Broadcast functionality in the BR/EDR
Controller.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 78

"7.1.49 Set Connectionless Slave Broadcast Command [New Section]
...
The LT_ADDR indicated in the Set_Connectionless_Slave_Broadcast shall be
pre-allocated using the HCI_Set_Reserved_LT_ADDR command. If the
LT_ADDR has not been reserved, the Unknown Connection Identifier (0x02)
error code shall be returned. If the controller is unable to reserve
sufficient bandwidth for the requested activity, the Connection Rejected
Due to Limited Resources (0x0D) error code shall be returned.

The LPO_Allowed parameter informs the BR/EDR Controller whether it is
allowed to sleep.

The Packet_Type parameter specifies which packet types are allowed. The
Host shall either enable BR packet types only, or shall enable EDR and DM1
packet types only.

The Interval_Min and Interval_Max parameters specify the range from which
the BR/EDR Controller must select the Connectionless Slave Broadcast
Interval. The selected Interval is returned."

Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add the structure for Write Sync Train Parameters

The Write_Synchronization_Train_Parameters command configures
the Synchronization Train functionality in the BR/EDR Controller.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 97

"7.3.90 Write Synchronization Train Parameters Command [New Section]
...
Note: The AFH_Channel_Map used in the Synchronization Train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.

Interval_Min and Interval_Max specify the allowed range of
Sync_Train_Interval. Refer to [Vol. 2], Part B, section 2.7.2 for
a detailed description of Sync_Train_Interval. The BR/EDR Controller shall
select an interval from this range and return it in Sync_Train_Interval.
If the Controller is unable to select a value from this range, it shall
return the Invalid HCI Command Parameters (0x12) error code.

Once started (via the Start_Synchronization_Train Command) the
Synchronization Train will continue until synchronization_trainTO slots have
passed or Connectionless Slave Broadcast has been disabled."

Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add the definition and structure for Set CSB Data

The Set_Connectionless_Slave_Broadcast_Data command provides the
ability for the Host to set Connectionless Slave Broadcast data in
the BR/EDR Controller.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 93

"7.3.88 Set Connectionless Slave Broadcast Data Command [New Section]
...
If connectionless slave broadcast mode is disabled, this data shall be
kept by the BR/EDR Controller and used once connectionless slave broadcast
mode is enabled. If connectionless slave broadcast mode is enabled,
and this command is successful, this data will be sent starting with
the next Connectionless Slave Broadcast instant.

The Data_Length field may be zero, in which case no data needs to be
provided.

The Host may fragment the data using the Fragment field in the command. If
the combined length of the fragments exceeds the capacity of the largest
allowed packet size specified in the Set Connectionless Slave Broadcast
command, all fragments associated with the data being assembled shall be
discarded and the Invalid HCI Command Parameters error (0x12) shall be
returned."

Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add the definition and structure for Delete Reserved LT_ADDR

The Delete_Reserved_LT_ADDR command requests that the BR/EDR
Controller cancel the reservation for a specific LT_ADDR reserved for the
purposes of Connectionless Slave Broadcast.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 92

"7.3.87 Delete Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is not reserved by the
BR/EDR Controller, it shall return the Unknown Connection Identifier (0x02)
error code.
If connectionless slave broadcast mode is still active, then the Controller
shall return the Command Disallowed (0x0C) error code."

Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add the definition and structure for Set Reserved LT_ADDR

The Set_Reserved_LT_ADDR command allows the host to request that the
BR/EDR Controller reserve a specific LT_ADDR for Connectionless Slave
Broadcast.

The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.

Bluetooth Core Specification Addendum 4 - Page 90

"7.3.86 Set Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is already in use by the
BR/EDR Controller, it shall return the ACL Connection Already Exists (0x0B)
error code. If the LT_ADDR indicated in the LT_ADDR parameter is out of
range, the controller shall return the Invalid HCI Command Parameters (0x12)
error code. If the command succeeds, then the reserved LT_ADDR shall be
used when issuing subsequent Set Connectionless Slave Broadcast Data and
Set Connectionless Slave Broadcast commands.
To ensure that the reserved LT_ADDR is not already allocated, it is
recommended that this command be issued at some point after HCI_Reset is
issued but before page scanning is enabled or paging is initiated."

Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

mac80211: implement STA CSA for drivers using channel contexts

Limit the current implementation to a single channel context used by
a single vif, thereby avoiding multi-vif/channel complexities.

Reuse the main function from AP CSA code, but move a portion out in
order to fit the STA scenario.

Add a new mac80211 HW flag so we don't break devices that don't support
channel switch with channel-contexts. The new behavior will be opt-in.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: pcie: fix merge damage

The merge b35c8097 seems to have lost commit eabc4ac5d,
put the code back.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: Increment management interface revision

This patch increments the management interface revision due to the
various fixes, improvements and other changes that have gone in
lately.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix advertising data flags with disabled BR/EDR

We shouldn't include the simultaneous LE & BR/EDR flags in the LE
advertising data if BR/EDR is disabled on a dual-mode controller. This
patch fixes this issue and ensures that the create_ad function generates
the correct flags when BR/EDR is disabled.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix REJECTED vs NOT_SUPPORTED mgmt responses

The REJECTED management response should mainly be used when the adapter
is in a state where we cannot accept some command or a specific
parameter value. The NOT_SUPPORTED response in turn means that the
adapter really cannot support the command or parameter value.

This patch fixes this distinction and adds two helper functions to
easily get the appropriate LE or BR/EDR related status response.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Add management command for setting static address

On dual-mode BR/EDR/LE and LE only controllers it is possible
to configure a random address. There are two types or random
addresses, one is static and the other private. Since the
random private addresses require special privacy feature to
be supported, the configuration of these two are kept separate.

This command allows for setting the static random address. It is
only supported on controllers with LE support. The static random
address is suppose to be valid for the lifetime of the controller
or at least until the next power cycle. To ensure such behavior,
setting of the address is limited to when the controller is
powered off.

The special BDADDR_ANY address (00:00:00:00:00:00) can be used to
disable the static address. This is also the default value.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Restrict disabling of HS when controller is powered off

Disabling the high speed setting when the controller is powered on has
too many side effects that are not taken care of. And in general it
is not an useful operation anyway. So just make such a command fail
with a rejection error message.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add a new mgmt_set_bredr command

This patch introduces a new mgmt command for enabling/disabling BR/EDR
functionality. This can be convenient when one wants to make a dual-mode
controller behave like a single-mode one. The command is only available
for dual-mode controllers and requires that LE is enabled before using
it. The BR/EDR setting can be enabled at any point, however disabling it
requires the controller to be powered off (otherwise a "rejected"
response will be sent).

Disabling the BR/EDR setting will automatically disable all other BR/EDR
related settings.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Introduce a new HCI_BREDR_ENABLED flag

To allow treating dual-mode (BR/EDR/LE) controllers as single-mode ones
(LE-only) we want to introduce a new HCI_BREDR_ENABLED flag to track
whether BR/EDR is enabled or not (previously we simply looked at the
feature bit with lmp_bredr_enabled).

This patch add the new flag and updates the relevant places to test
against it instead of using lmp_bredr_enabled. The flag is by default
enabled when registering an adapter and only cleared if necessary once
the local features have been read during the HCI init procedure.

We cannot completely block BR/EDR usage in case user space uses raw HCI
sockets but the patch tries to block this in places where possible, such
as the various BR/EDR specific ioctls.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

cfg80211: vlan priority handling in WMM

If the VLAN tci is set in skb->vlan_tci use the
priority field to determine the WMM priority.

Signed-off-by: cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Bluetooth: btmrvl: add calibration data download support

A text file containing calibration data in hex format can
be provided at following path:

/lib/firmware/mrvl/sd8797_caldata.conf

The data will be downloaded to firmware during initialization.

Reviewed-by: Mike Frysinger <vapier@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: btmrvl: add setup handler

Move initialization code to hdev's setup handler.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: btmrvl: get rid of struct btmrvl_cmd

Replace this proprietary structure with the standard one
(struct hci_command_hdr).

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: btmrvl: add btmrvl_send_sync_cmd() function

Command preparation code is used multiple times. This patch
separate out this common code and create btmrvl_send_sync_cmd()
function.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Fix workqueue synchronization in hci_dev_open

When hci_sock.c calls hci_dev_open it needs to ensure that there isn't
pending work in progress, such as that which is scheduled for the
initial setup procedure or the one for automatically powering off after
the setup procedure. This adds the necessary calls to ensure that any
previously scheduled work is completed before attempting to call
hci_dev_do_open.

This patch fixes a race with old user space versions where we might
receive a HCIDEVUP ioctl before the setup procedure has been completed.
When that happens the setup procedures callback may fail early and leave
the device in an inconsistent state, causing e.g. the setup callback to
be (incorrectly) called more than once.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Refactor hci_dev_open to a separate hci_dev_do_open function

The requirements of an external call to hci_dev_open from hci_sock.c are
different to that from within hci_core.c. In the former case we want to
flush any pending work in hdev->req_workqueue whereas in the latter we
don't (since there we are already calling from within the workqueue
itself). This patch does the necessary refactoring to a separate
hci_dev_do_open function (analogous to hci_dev_do_close) but does not
yet introduce the synchronizations relating to the workqueue usage.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Enable -D__CHECK_ENDIAN__ for sparse by default

The Bluetooth protocol and hardware is pretty much all little endian
and so when running sparse via "make C=2" for example, enable the
endian checks by default.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Require CAP_NET_ADMIN for HCI User Channel operation

The HCI User Channel operation is an admin operation that puts the
device into promiscuous mode for single use. It is more suitable
to require CAP_NET_ADMIN than CAP_NET_RAW.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Send new settings event when changing high speed option

When enabling or disabling high speed setting it is required to send
a new settings event to inform other management interface users about
the changed settings.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Provide high speed configuration option

Hiding the Bluetooth high speed support behind a module parameter is
not really useful. This can be enabled and disabled at runtime via
the management interface. This also has the advantage that this can
now be changed per controller and not just global.

This patch removes the module parameter and exposes the high speed
setting of the management interface to all controllers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Replace BDADDR_LOCAL with BDADDR_NONE

The BDADDR_LOCAL is a relict from userspace and has never been used
within the kernel. So remove that constant and replace it with a new
BDADDR_NONE that is similar to HCI_DEV_NONE with all bits set.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Use only 2 bits for controller type information

The controller type is limited to BR/EDR/LE and AMP controllers. This
can be easily encoded with just 2 bits and still leave enough room
for future controller types.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

regulatory: enable channels 52-64 and 100-144 for world roaming

If allowed in a country, these channels typically require DFS
so mark them as such. Channel 144 is a bit special, it's coming
into use now to allow more VHT 80 channels, but world roaming
with passive scanning is acceptable anyway. It seems fairly
unlikely that it'll be used as the control channel for a VHT
AP, but it needs to be present to allow a full VHT connection
to an AP that uses it as one of the secondary channels.

Also enable VHT 160 on these channels, and also for channels
36-48 to be able to use VHT 160 there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211: allow CAC only if no operation is going on

A CAC should fail if it is triggered while the interface is already
running.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: improve default WMM parameter setting

Move the default setting for WMM parameters outside the for loop
to avoid redundant assignment multiple times.

Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: support reporting A-MSDU subframes individually

Some devices may not be able to report A-MSDUs in
single buffers. Drivers for such devices were
forced to re-assemble A-MSDUs which would then
be eventually disassembled by mac80211. This could
lead to CPU cache thrashing and poor performance.

Since A-MSDU has a single sequence number all
subframes share it. This was in conflict with
retransmission/duplication recovery
(IEEE802.11-2012: 9.3.2.10).

Patch introduces a new flag that is meant to be
set for all individually reported A-MSDU subframes
except the last one. This ensures the
last_seq_ctrl is updated after the last subframe
is processed. If an A-MSDU is actually a duplicate
transmission all reported subframes will be
properly discarded.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[johannes: add braces that were missing even before]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: use exact-size allocation for authentication frame

The authentication frame has a fixied size of 30 bytes
(including header, algo num, trans seq num, and status)
followed by a variable challenge text.
Allocate using exact size, instead of over-allocation
by sizeof(ieee80211_mgmt).

Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: parse dfs region for internal regdb option

Add support for parsing and setting the dfs region (ETSI, FCC, JP)
when the internal regulatory database is used. Before this
the DFS region was being ignored even if present on the used
db.txt

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: add explicit IBSS driver operations

This can be useful for drivers if they have any failure cases
when joining an IBSS. Also move setting the queue parameters
to before this new call, in case the new driver op needs them
already.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ieee80211: fix vht cap definitions

VHT_CAP_BEAMFORMER_ANTENNAS cap is actually defined in the draft as
VHT_CAP_BEAMFORMEE_STS_MAX, and its size is 3 bits long.

VHT_CAP_SOUNDING_DIMENSIONS is also 3 bits long.

Fix the definitions and change the cap masking accordingly.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix some snprintf misuses

In some debugfs related functions snprintf was used
while scnprintf should have been used instead.

(blindly adding the return value of snprintf and supplying
it to the next snprintf might result in buffer overflow when
the input is too big)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wlcore: always register dummy hardirq

This keeps the kernel happy when using edge-irqs and requesting a
threaded irq.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wl18xx: print new RDL versions during boot

Extract and print info for the new RDL 5, 6, 7 and 8.
Replace const struct with function which translates
the RDL number to string.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wl18xx: fix boot process in high temperature environment

In addition to existing WCS PLL configuration add and enable
also the coex PLL during init phase. This fixes boot failures
due to silicon latchup in high temperature environment (>85c).

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wlcore: clarify and fix regulatory domain bit translation

Channels 52-64 were mapped incorrectly.

Refactor and document wlcore_get_reg_conf_ch_idx() in
order to make it clear what's going on there.

While on it, fix the return value check to consider
0 as a valid return value as well (indicates channel 1).

Reported-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wlcore: remove unsupported channels

The fw doesn't support channels 7,9,11 in 5ghz band,
so don't advertise supporting them.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wlcore: fix unsafe dereference of the wlvif

wlvif could be passed as NULL from the wlcore_tx_work_locked()
to the wl1271_prepare_tx_frame() and to wl1271_skb_queue_head()
functions. This may lead to a Kernel panic, fix this by
validating that wlvif != NULL.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wlcore: cleanup scan debug prints

Remove scan debug dumps which are rarely used.
Make scan debug prints more clear and short.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wlcore: re-enable idle handling

We need some stuff done on idle change, most notably we have to stop
sched-scanning. Take care of this by reintroducing idle handling.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wlcore: disable elp sleep while in plt mode

We now disable elp sleep during plt mode to allow normal operation of
plt tools such as calibrator.

Having elp_sleep enabled during plt mode is actually not required and
in fact it disrupt plt operations such as rx statistics etc.

Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wlcore: add new plt power-mode: CHIP_AWAKE

Under this mode the chip is powered on including sdio
but no FW is downloaded and run, interrupts are not enabled, etc...

This mode is intended to allow RTTT to bridge sdio as a transport
to the chip.

Driver only provides sdio access using the dev_mem debugfs file.

Some fixes done to the code that ensures that PLT mode and normal
driver power mode (ifconfig/add_interface) are mutually excluded.

Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

wlcore: ROC on AP channel before auth reply

Start a ROC on the AP channel beforing sending the authentication reply
to a connecting STA. This ROC is held up to 1 second via a timer. If the
station is authorized and added by mac80211, the ROC is extended until
the station is fully authorized.
We make sure not to ROC twice when several stations are connecting in
parallel and to only release the ROC when both the pending-reply timer
and the STA-state callbacks do not require it.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth

Conflicts:
net/bluetooth/hci_core.c

rt2x00: Fix rf register for RT3070

Fix RT3070 chip RF initial value to be similar to the latest Ralink vendor
driver.

Tested on Asus N13 usb wifi dongle.

Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rtlwifi: Replace variable with a break

This patch removes the variable continual, and change the while loop
to break when efuse_data == 0xFF.

Tested by compilation only.

CC: Joe Perches <joe@perches.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>