David Daney [Fri, 23 Jul 2010 17:43:49 +0000 (10:43 -0700)]
MIPS: Octeon: Make MSI use handle_simple_irq().
The use of handle_percpu_irq() is not really what we want for MSI, use
handle_simple_irq() instead. This is probably the prototypical case
for using handle_simple_irq(), because all the MSIs are dispatched from
the root interrupt service routine.
Also since the base IRQ is not shared, don't pass IRQF_SHARED.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1488/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Fri, 23 Jul 2010 17:43:46 +0000 (10:43 -0700)]
MIPS: Octeon: Improve interrupt handling.
The main change is to change most of the IRQs from handle_percpu_irq
to handle_fasteoi_irq. This necessitates extracting all the .ack code
to common functions that are not exposed to the irq core.
The affinity code now acts more sanely, by doing round-robin
distribution instead of broadcasting.
Because of the change to handle_fasteoi_irq and affinity, some of the
IRQs had to be split into separate groups with their own struct
irq_chip to prevent undefined operations on specific IRQ lines.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1485/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Wed, 21 Jul 2010 12:30:50 +0000 (14:30 +0200)]
MIPS: au1000_eth: Get ethernet address from platform_data
au1000_eth uses firmware calls to get a valid MAC address, and changes
it depending on platform device id. This patch moves this logic out of
the driver into the platform device registration part, where boards with
supported chips can use whatever firmware interface they need; the default
implementation maintains compatibility with existing, YAMON-based firmware.
Tested-by: Wolfgang Grandegger <wg@denx.de> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org> Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1481/ Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Thu, 15 Jul 2010 19:45:05 +0000 (21:45 +0200)]
SERIAL: 8250: Remove SERIAL_8250_AU1X00
Remove the SERIAL_8250_AU1X00 config symbol. Instead, use the MIPS_ALCHEMY
one which is always defined when building an Au1x00-based platform.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org> Cc: Linux-serial <linux-serial@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This one depends on a previous patch (which removes SOC_AU1X00 and changes
MACH_ALCHEMY) to apply cleanly (and then actually work), so I'd love for
this to go in via the mips tree.
The commit "MIPS: Tracing: Cleanup the arguments passing of
prepare_ftrace_return" has moved the "jal prepare_ftrace_return"
instruction after the handling of the 3rd argument but forgot to remove
the superfluous space before the related instructions.
Although all EMMAxxx SoCs can support IP2 and IP3 hardware interrupts,
current EMMA2RH plat_irq_dispatch() supports IP2 only. We can make it
configurable in the future, but for the time being, would like to make
things explicitly allcated to IP2 in accordance with plat_irq_dispatch().
For historical reasons, we used to put MIPS CPU IRQs behind SoC-specific
IRQs in the queue, and have been using CPU_IRQ_BASE as MIPS_CPU_IRQ_BASE.
In recent years, however, we've brought it back to normal order, and now
CPU_IRQ_BASE just redefines the generic MIPS_CPU_IRQ_BASE.
At the same time, NUM_CPU_IRQ is also removed as useless.
Shamelessly stealing wisdom from pasemi_mac.c, I found char2hex() could
be replaced with a single call to sscanf(), looks cleaner to me at
least. The result is 100 bytes trimmed off the size of a compiled
cpmac_get_mac() and as an extra bonus it grumbles and gracefully fails
over to using random_ether_addr() when an attempt to parse an invalid
MAC address is made.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
To: linux-mips@linux-mips.org Cc: florian@openwrt.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David VomLehn [Thu, 1 Jul 2010 20:37:52 +0000 (13:37 -0700)]
MIPS: PowerTV: Simplify command line handling and needed config changes
Additional changes to Youichi Yuasa's command line simplication code
The PowerTV platform uses a non-standard way to get the kernel command
line--we insert a built-in command line into arcs_cmdline and to
get additional command line information from the bootloader via a
pointer in the a1 register. It is necessary to insert a space between
to the two strings or the last argument from arcs_cmdline and the first
argument from the bootloader may be inadvertantly combined.
It is also necessary to set CONFIG_CMDLINE_BOOL to "y" and to set the
default command line to an empty string to get the simplified code to
work properly in the PowerTV environment.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1438/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Christoph Egger [Wed, 9 Jun 2010 11:23:02 +0000 (13:23 +0200)]
MIPS: PowerTV: Removing dead CONFIG_DIAGNOSTICS
CONFIG_DIAGNOSTICS doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
To: David VomLehn <dvomlehn@cisco.com>
To: Yoichi Yuasa <yuasa@linux-mips.org>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org Cc: vamos@i4.informatik.uni-erlangen.de
Patchwork: https://patchwork.linux-mips.org/patch/1374/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Christoph Egger [Wed, 9 Jun 2010 11:21:30 +0000 (13:21 +0200)]
MIPS: Remove dead CONFIG_MTD_PB1550_BOOT, CONFIG_MTD_PB1550_USER
CONFIG_MTD_PB1550_BOOT, CONFIG_MTD_PB1550_USER doesn't exist in
Kconfig, therefore removing all references for it from the source
code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
To: Manuel Lauss <manuel.lauss@gmail.com>,
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org Cc: vamos@i4.informatik.uni-erlangen.de
Patchwork: https://patchwork.linux-mips.org/patch/1370/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Christoph Egger [Wed, 9 Jun 2010 11:20:41 +0000 (13:20 +0200)]
MIPS: Cavium: Remove dead CONFIG_GDB_CONSOLE
CONFIG_GDB_CONSOLE doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
To: David Daney <ddaney@caviumnetworks.com>
To: Yang Shi <yang.shi@windriver.com>
To: Herbert Xu <herbert@gondor.apana.org.au>
To: Tejun Heo <tj@kernel.org>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org Cc: vamos@i4.informatik.uni-erlangen.de
Patchwork: https://patchwork.linux-mips.org/patch/1368/ Acked-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Kevin Cernekee [Fri, 4 Jun 2010 05:11:25 +0000 (22:11 -0700)]
printk: fix delayed messages from CPU hotplug events
When a secondary CPU is being brought up, it is not uncommon for
printk() to be invoked when cpu_online(smp_processor_id()) == 0. The
case that I witnessed personally was on MIPS:
http://lkml.org/lkml/2010/5/30/4
If (can_use_console() == 0), printk() will spool its output to log_buf
and it will be visible in "dmesg", but that output will NOT be echoed to
the console until somebody calls release_console_sem() from a CPU that
is online. Therefore, the boot time messages from the new CPU can get
stuck in "limbo" for a long time, and might suddenly appear on the
screen when a completely unrelated event (e.g. "eth0: link is down")
occurs.
This patch modifies the console code so that any pending messages are
automatically flushed out to the console whenever a CPU hotplug
operation completes successfully or aborts.
The issue was seen on 2.6.34.
Original patch by Kevin Cernekee with cleanups by akpm and additional fixes
by Santosh Shilimkar. This patch superseeds
https://patchwork.linux-mips.org/patch/1357/.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
To: <mingo@elte.hu>
To: <akpm@linux-foundation.org>
To: <simon.kagstrom@netinsight.net>
To: <David.Woodhouse@intel.com>
To: <lethal@linux-sh.org> Cc: <linux-kernel@vger.kernel.org> Cc: <linux-mips@linux-mips.org> Reviewed-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1534/
LKML-Reference: <ede63b5a20af951c755736f035d1e787772d7c28@localhost>
LKML-Reference: <EAF47CD23C76F840A9E7FCE10091EFAB02C5DB6D1F@dbde02.ent.ti.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sam Ravnborg [Sun, 30 May 2010 14:28:03 +0000 (16:28 +0200)]
MIPS: Refactor arch/mips/boot/compressed/Makefile
- use hostprogs-y for the elf2ecoff
- list all *.o file in targets
- renamed obj-y to vmlinuzobjs-y (it was confusing to re-use a kbuild variable)
- fix all uses of if_changed/cmd
- use kbuild rules to beautify output
- update clean-file to clean vmlinuz.* in top-level directory
- simplied logic in arch/mips/Makefile for compressed targets
The net result is a more kbuild conformant Makefile but
readability did not increase.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips <linux-mips@linux-mips.org>
To: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1304/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sam Ravnborg [Sun, 30 May 2010 14:27:33 +0000 (16:27 +0200)]
MIPS: Refactor arch/mips/boot/Makefile
- remove stuff that is not needed
VMLINUX assignment, all: rule
- use hostprogs-y for the host program
- use kbuild rules for the three targets - to beautify output
- drop clean-files - it is no longer needed
- simplify arch/mips/Makefile when calling targets in boot/Makefile
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips <linux-mips@linux-mips.org>
To: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1303/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 5 Aug 2010 12:25:56 +0000 (13:25 +0100)]
MIPS: PNX8550: Move code one directory level up.
It was sharing the nxp directory but no code with pnx833x and will fit
better into the new platform makefile scheme, if moved. Also after the
pnx833x code has been moved up, the pnx8550 Code was the last users of
the nxp dir.
FUJITA Tomonori [Wed, 23 Jun 2010 16:26:09 +0000 (01:26 +0900)]
MIPS: Alchemy: fix deprecated compile warnings
Replace deprecated DMA_32BIT_MASK with DMA_BIT_MASK. This is needed because
the new style platform makefiles will enable -Werror.
cc1: warnings being treated as errors
arch/mips/alchemy/devboards/db1200/platform.c:219: error: 'DMA_nnBIT_MASK' is deprecated
arch/mips/alchemy/devboards/db1200/platform.c:226: error: 'DMA_nnBIT_MASK' is deprecated
arch/mips/alchemy/devboards/db1200/platform.c:388: error: 'DMA_nnBIT_MASK' is deprecated
arch/mips/alchemy/devboards/db1200/platform.c:393: error: 'DMA_nnBIT_MASK' is deprecated
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
To: linux-mips@linux-mips.org Acked-by: Manuel Lauss <manuel.lauss@googlemail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1427/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sam Ravnborg [Sun, 30 May 2010 14:27:10 +0000 (16:27 +0200)]
MIPS: Introduce support for Platform definitions
Move platform specific definitions to the platfrom directories.
Each platform shall do the following:
1) include an entry in arch/mips/Kbuild.platforms
2) add relevant definitions to arch/mips/<platform>/Platform
This commits changes ar7 to the new scheme as an example.
Introducing a platform speecific Platfrom file has following advantages:
1) decentralization of platfrom definitions
2) simplification af arch/mips/Makefile
3) force all platfrom to build with -Werror (done in arch/mips/Kbuild)
[Ralf: Remove forgotten -Werror from AR7 Makefile]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips <linux-mips@linux-mips.org>
To: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1302/
Patchwork: http://patchwork.linux-mips.org/patch/1308/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Andrea Gelmini [Sun, 23 May 2010 19:52:12 +0000 (21:52 +0200)]
MIPS: IP27: klconfig.c checkpatch cleanup
arch/mips/sgi-ip27/ip27-klconfig.c:51: ERROR: "foo * bar" should be "foo *bar"
arch/mips/sgi-ip27/ip27-klconfig.c:63: ERROR: "foo * bar" should be "foo *bar"
arch/mips/sgi-ip27/ip27-klconfig.c:81: ERROR: "foo * bar" should be "foo *bar"
arch/mips/sgi-ip27/ip27-klconfig.c:100: ERROR: "foo * bar" should be "foo *bar"
Andrea Gelmini [Sun, 23 May 2010 19:52:03 +0000 (21:52 +0200)]
MIPS: Yosemite: ht-irq.c: Checkpatch cleanup
arch/mips/pmc-sierra/yosemite/ht-irq.c:38: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:39: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:40: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:43: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:44: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:45: ERROR: code indent should use tabs where possible
David VomLehn [Fri, 21 May 2010 18:25:36 +0000 (11:25 -0700)]
MIPS: PowerTV: Use O(1) algorthm for phys_to_dma/dma_to_phys
Replace phys_to_dma()/dma_to_phys() looping algorithm with an O(1) algorithm
The approach taken is inspired by the sparse memory implementation: take a
certain number of high-order bits off the address them, use this as an
index into a table containing an offset to the desired address and add
it to the original value. There is a table for mapping physical addresses
to DMA addresses and another one for the reverse mapping. The table sizes
depend on how fine-grained the mappings need to be; Coarser granularity
less to smaller tables. On a processor with 32-bit physical and DMA
addresses, with 4 MIB granularity, memory usage is two 2048-byte arrays.
Each 32-byte cache line thus covers 64 MiB of address space.
Also, renames phys_to_bus() to phys_to_dma() and bus_to_phys() to
dma_to_phys() to align with kernel usage.
[Ralf: Fixed silly build breakage due to stackoverflow warning caused by
huge array on stack.]
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1257/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 3 Aug 2010 02:42:32 +0000 (03:42 +0100)]
MIPS: MTX1: Fix build.
CC arch/mips/alchemy/mtx-1/board_setup.o
{standard input}: Assembler messages:
{standard input}:263: Error: opcode not supported on this processor: mips1 (mips1) `sync'
{standard input}:274: Error: opcode not supported on this processor: mips1 (mips1) `sync'
{standard input}:296: Error: opcode not supported on this processor: mips1 (mips1) `sync'
[...]
Any .set mipsX statement other than .set mips0 at the end of inline
assembler is a big fat bug.
The BCM47xx architecture maps the ram into a 128MB address space. It
will be spaced there as often as goes into the 128MB. Detection tries to
find the position where the same memory is found. When reading beyond
128MB the processor will throw an exception. If 128MB RAM is installed,
it will not find a memory alias because it tries to read beyond the 128MB
border. Now it just assumes 128MB installed ram if it can not find an
alias.
MIPS: Octeon: Workaround link failures with gcc-4.4.x 32-bits toolchains
When building with a gcc-4.4.x toolchain that is configured to produce
32-bits executables by default, we will produce __lshrti3 in sched_clock()
which is never resolved so the kernel fails to link. Unconditionally use
the inline assembly version as suggested by David Daney, which works around
the issue.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1514/ Acked-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 19 May 2010 17:40:53 +0000 (10:40 -0700)]
MIPS: Don't overflow cevt-r4k.c calculations at high clock rates.
The 'mult' element of struct clock_event_device must never be wider
than 32-bits. If it were, it would get truncated when used by
clockevent_delta2ns() when this calls do_div().
We can meet this requirement by using clockevent_set_clock() to set
the MULT and SHIFT values.
Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1253/ Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Julia Lawall [Sun, 9 Aug 2009 09:42:32 +0000 (11:42 +0200)]
VIDEO: Correct use of request_region/request_mem_region
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
* master.kernel.org:/home/rmk/linux-2.6-arm:
cyber2000fb: fix console in truecolor modes
cyber2000fb: fix machine hang on module load
SA1111: Eliminate use after free
ARM: Fix Versatile/Realview/VExpress MMC card detection sense
ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
ARM: Add barriers to io{read,write}{8,16,32} accessors as well
ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
ARM: 6271/1: Introduce *_relaxed() I/O accessors
ARM: 6275/1: ux500: don't use writeb() in uncompress.h
ARM: 6270/1: clean files in arch/arm/boot/compressed/
ARM: Fix csum_partial_copy_from_user()
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Ensure that writepage respects the nonblock flag
NFS: kswapd must not block in nfs_release_page
nfs: include space for the NUL in root path
projects / karo-tx-linux.git / log