The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: Jack Lee <jlee@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.
Cc: Paul Shaw <paul.shaw@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.
Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.
This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.
What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.
Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 6cd0b1cb872b3bf9fc5de4536404206ab74bafdd "iwlagn: fix
hw-rfkill while the interface is down", we enable interrupts when
device is not ready to receive them. However hardware, when it is in
some inconsistent state, can generate other than rfkill interrupts
and crash the system. I can reproduce crash with "kernel BUG at
drivers/net/wireless/iwlwifi/iwl-agn.c:1010!" message, when forcing
firmware restarts.
To fix only enable rfkill interrupt when down device and after probe.
I checked patch on laptop with 5100 device, rfkill change is still
passed to user space when device is down.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.
To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the buffer size is set to zero in the block ack parameter set
field, we should use the maximum supported number of subframes. The
existing code was bogus and was doing some unnecessary calculations
that lead to wrong values.
Thanks Johannes for helping me figure this one out.
Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luciano Coelho <coelho@ti.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
removed the synchronization against RCU and thus
opened a race window where we can use a key for
TX while it is already freed. Put a synchronisation
into the right place to close that window.
Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under memory pressure, the mac80211 mesh code
may helpfully print a message that it failed
to clone a mesh frame and then will proceed
to crash trying to use it anyway. Fix that.
Avoid the reference whenever the frame copy is unsuccessful
regardless of the debug message being suppressed or printed.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI PM suspend callback took down the interface and resume brought
it back up. In the mac80211 context this is done in subsequent calls.
Rework implementation so that suspend only stores config, and sets
PCI power state. The resume return to full power state (D0), restores
the config, and brings hardware back up. Full bringup is done by
subsequent mac80211 calls.
The hv_netvsc gets RNDIS_STATUS_MEDIA_CONNECT event after the VM
is live migrated. Adding call to netif_notify_peers() for this event
to send GARP (Gratuitous ARP) to notify network peers. Otherwise,
the VM's network connection may stop after a live migration.
This patch should also be applied to stable kernel 2.6.32 and later.
Removed the call to netif_stop_queue() in netvsc_probe() as
the queue is not initialized at that point and further call
to it after queue initialization is really not necessary.
This change was prompted after an upstream change went into
2.6.37 (netif_tx_stop_queue) that now checks if netif_stop_queue
is called before register with netdev is done.
This will eliminate the warning message to the log when hv_netvsc
driver starts up.
The ni_labpc driver module only requests a shared IRQ for PCI devices,
requesting a non-shared IRQ for non-PCI devices.
As this module is also used by the ni_labpc_cs module for certain
National Instruments PCMCIA cards, it also needs to request a shared IRQ
for PCMCIA devices, otherwise you get a IRQ mismatch with the CardBus
controller.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds several new device ids to the r8712u staging driver.
The new ids were retrieved from latest vendor driver (v2.6.6.0.20101111)
downloadable from www.realtek.com.tw
Signed-off-by: Axel Koellhofer <AxelKoellhofer@web.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In zram_read() and zram_write() we were not incrementing the
index number and thus were reading/writing values from/to
incorrect sectors on zram disk, resulting in data corruption.
The USB core keeps track of pending resume requests for root hubs, in
order to resolve races between wakeup requests and suspends. However
the code that does this is subject to another race (between wakeup
requests and resumes) because the WAKEUP_PENDING flag is cleared
before the resume occurs, leaving a window in which another wakeup
request might arrive.
This patch (as1447) fixes the problem by clearing the WAKEUP_PENDING
flag after the resume instead of before it.
This fixes Bugzilla #24952.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Paul Bender <pebender@san.rr.com> Tested-by: warpme <warpme@o2.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If anyone comes across a high-speed hub that (by mistake or by design)
claims to have no Transaction Translators, plugging a full- or
low-speed device into it will cause the USB stack to crash. This
patch (as1446) prevents the problem by ignoring such devices, since
the kernel has no way to communicate with them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Perry Neben <neben@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The major and minor number saved in the product_info structure
were copied from the address instead of the data, causing an
inconsistency in the reported versions during firmware loading:
usb 4-1: firmware: requesting edgeport/down.fw
/usr/src/linux/drivers/usb/serial/io_edgeport.c: downloading firmware version (930) 1.16.4
[..]
/usr/src/linux/drivers/usb/serial/io_edgeport.c: edge_startup - time 3 4328191260
/usr/src/linux/drivers/usb/serial/io_edgeport.c: FirmwareMajorVersion 0.0.4
This can cause some confusion whether firmware loaded successfully
or not.
This patch (as1442) fixes a bug in g_printer: Module parameters should
not be marked "__initdata" if they are accessible in sysfs (i.e., if
the mode value in the module_param() macro is nonzero). Otherwise
attempts to access the parameters will cause addressing violations.
Character-string module parameters must not be marked "__initdata"
if the module can be unloaded, because the kernel needs to access the
parameter variable at unload time in order to free the
dynamically-allocated string.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Roland Kletzing <devzero@web.de> CC: Craig W. Nadler <craig@nadler.us> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1441) fixes a bug in g_printer. The gadget driver, char
device number, and class device should be unregistered in reverse
order of registration. As it is now, when the module is unloaded the
class device gets unregistered first, causing a crash when the unbind
method tries to access it.
This fixes Bugzilla #25882.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Roland Kletzing <devzero@web.de> CC: Craig W. Nadler <craig@nadler.us> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is
used to compute the size in a dma_alloc_coherent() call, but then it
gets changed later on. As a result, the corresponding call to
dma_free_coherent() passes a different size from the original
allocation. Fix the problem by adjusting ehci->periodic_size before
carrying out any of the memory allocations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1443) fixes a bug found in many of the USB serial
drivers: They don't set the .usb_driver field in their
usb_serial_driver structure. This field is needed for assigning
dynamic IDs for device matching.
In addition, starting with the 2.6.37 kernel, the .usb_driver field is
needed for proper autosuspend operation. Without it, attempts to open
the device file will fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/drivers/usb/serial/option.c: Adding support for Cinterion's HC25, HC28,
HC28J, EU3-E, EU3-P and PH8 by correcting/adding Cinterion's and
Siemens' Vendor IDs as well as Product IDs and USB_DEVICE tuples
Signed-off-by: Nicolaus Colberg <nicolaus.colberg@cinterion.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found the original patch on the db0fhn repeater wiki (couldn't find the email
of the origial author) I guess it was never commited.
I updated and added some Icom HAM-radio devices to the ftdi driver.
Added extra comments to make clear what devices it are.
This patch (as1438) adds an unusual_devs entry for the MagicPixel
FW_Omega2 chip, used in the CamSport Evo camera. The firmware
incorrectly reports a vendor-specific bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: <ttkspam@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TrekStor DataStation maxi g.u external hard drive enclosure uses a
JMicron USB to SATA chip which needs the US_FL_IGNORE_RESIDUE flag to work
properly.
Signed-off-by: Richard Schütz <r.schtz@t-online.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device ID removed 0x10C4/0x8149 for West Mountain Radio Computerized
Battery Analyzer. This device is actually based on a SiLabs C8051Fxxx,
see http://www.etheus.net/SiUSBXp_Linux_Driver for further info.
Alan's commit 335f8514f200e63d689113d29cb7253a5c282967 introduced
.carrier_raised function in several drivers. That also means
tty_port_block_til_ready can now suspend the process trying to open the serial
port when Carrier Detect is low and put it into tty_port.open_wait queue. We
need to wake up the process when Carrier Detect goes high and trigger TTY
hangup when CD goes low.
Some of the devices do not report modem status line changes, or at least we
don't understand the status message, so for those we remove .carrier_raised
again.
The device init is used to reset the accelerometer. Failure to reset
is not severe enough to stop loading the module or to resume from
hibernation. This patch relaxes failure to a warning and drops
output in case of success.
Functions set_fan_min() and set_fan_div() assume that the fan_div
values have already been read from the register. The driver currently
doesn't initialize them at load time, they are only set when function
via686a_update_device() is called. This means that set_fan_min() and
set_fan_div() misbehave if, for example, "sensors -s" is called
before any monitoring application (e.g. "sensors") is has been run.
Fix the problem by always initializing the fan_div values at device
bind time.
Fix a hard-coded limit of a maximum of 16 cpu's per socket.
The UV Broadcast Assist Unit code initializes by scanning the
cpu topology of the system and assigning a master cpu for each
socket and UV hub. That scan had an assumption of a limit of 16
cpus per socket. With Westmere we are going over that limit.
The UV hub hardware will allow up to 32.
If the scan finds the system has gone over that limit it returns
an error and we print a warning and fall back to doing TLB
shootdowns without the BAU.
ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page. This
is achieved by setting queue DMA alignment. If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.
This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors(). Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.
This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size. While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: John Stanley <jpsinthemix@verizon.net> Tested-by: John Stanley <jpsinthemix@verizon.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ASPM PM Feature is enabled on UMI link, devices that use ISOC stream of
data transfer may be exposed to longer latency causing less than optimal per-
formance of the device. The longer latencies are normal and are due to link
wake time coming out of low power state which happens frequently to save
power when the link is not active.
The following code will make exception for certain features of ASPM to be by
passed and keep the logic normal state only when the ISOC device is connected
and active. This change will allow the device to run at optimal performance
yet minimize the impact on overall power savings.
Signed-off-by: Alex He <alex.he@amd.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the vhci_urb_dequeue() function the TCP connection is checked twice.
Each time when the TCP connection is closed the URB is unlinked and given
back. Remove the second attempt of unlinking and giving back of the URB completely.
This patch fixes the bug described at https://bugzilla.kernel.org/show_bug.cgi?id=24872 .
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv4/route.c: respect prefsrc for local routes
bridge: stp: ensure mac header is set
bridge: fix br_multicast_ipv6_rcv for paged skbs
atl1: fix oops when changing tx/rx ring params
drivers/atm/atmtcp.c: add missing atm_dev_put
starfire: Fix dma_addr_t size test for MIPS
tg3: fix return value check in tg3_read_vpd()
Broadcom CNIC core network driver: fix mem leak on allocation failures in cnic_alloc_uio_rings()
ISDN, Gigaset: Fix memory leak in do_disconnect_req()
CAN: Use inode instead of kernel address for /proc file
skfp: testing the wrong variable in skfp_driver_init()
ppp: allow disabling multilink protocol ID compression
ehea: Avoid changing vlan flags
ueagle-atm: fix PHY signal initialization race
Joel Sing [Mon, 3 Jan 2011 20:24:20 +0000 (20:24 +0000)]
ipv4/route.c: respect prefsrc for local routes
The preferred source address is currently ignored for local routes,
which results in all local connections having a src address that is the
same as the local dst address. Fix this by respecting the preferred source
address when it is provided for local routes.
This bug can be demonstrated as follows:
# ifconfig dummy0 192.168.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 192.168.0.1
# ip route change table local local 192.168.0.1 dev dummy0 \
proto kernel scope host src 127.0.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 127.0.0.1
We now establish a local connection and verify the source IP
address selection:
Thus without the patch, with the boot parameters 'tcb selinux=0', adding
the above 'dont_measure obj_type=var_log_t' rule to the default IMA TCB
measurement policy, would result in nothing being measured. The patch
prevents the default TCB policy from being replaced.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com> Cc: James Morris <jmorris@namei.org> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Cc: David Safford <safford@watson.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This seems fine itself, but br_send_bpdu() invokes ebtables LOCAL_OUT.
We oops in ebt_basic_match() because it assumes eth_hdr(skb) returns
a meaningful result.
Cc: acme@ghostprotocols.net
References: https://bugzilla.kernel.org/show_bug.cgi?id=24532 Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 3 Jan 2011 19:51:22 +0000 (11:51 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix callchain hit bad cast on ascii display
arch/x86/oprofile/op_model_amd.c: Perform initialisation on a single CPU
watchdog: Improve initialisation error message and documentation
Linus Torvalds [Mon, 3 Jan 2011 19:50:26 +0000 (11:50 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] em28xx: radio_fops should also use unlocked_ioctl
[media] wm8775: Revert changeset fcb9757333 to avoid a regression
[media] cx25840: Prevent device probe failure due to volume control ERANGE error
Linus Torvalds [Mon, 3 Jan 2011 19:48:54 +0000 (11:48 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: provide dummy functions for DMA_ENGINE=n
mv_xor: fix race in tasklet function
Tomas Winkler [Mon, 3 Jan 2011 19:26:08 +0000 (11:26 -0800)]
bridge: fix br_multicast_ipv6_rcv for paged skbs
use pskb_may_pull to access ipv6 header correctly for paged skbs
It was omitted in the bridge code leading to crash in blind
__skb_pull
since the skb is cloned undonditionally we also simplify the
the exit path
this fixes bug https://bugzilla.kernel.org/show_bug.cgi?id=25202
Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 IEEE 802.11: authenticated
Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 IEEE 802.11: associated (aid 2)
Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 RADIUS: starting accounting session 4D0608A3-00000005
Dec 15 14:36:41 User-PC kernel: [175576.120287] ------------[ cut here ]------------
Dec 15 14:36:41 User-PC kernel: [175576.120452] kernel BUG at include/linux/skbuff.h:1178!
Dec 15 14:36:41 User-PC kernel: [175576.120609] invalid opcode: 0000 [#1] SMP
Dec 15 14:36:41 User-PC kernel: [175576.120749] last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/uevent
Dec 15 14:36:41 User-PC kernel: [175576.121035] Modules linked in: approvals binfmt_misc bridge stp llc parport_pc ppdev arc4 iwlagn snd_hda_codec_realtek iwlcore i915 snd_hda_intel mac80211 joydev snd_hda_codec snd_hwdep snd_pcm snd_seq_midi drm_kms_helper snd_rawmidi drm snd_seq_midi_event snd_seq snd_timer snd_seq_device cfg80211 eeepc_wmi usbhid psmouse intel_agp i2c_algo_bit intel_gtt uvcvideo agpgart videodev sparse_keymap snd shpchp v4l1_compat lp hid video serio_raw soundcore output snd_page_alloc ahci libahci atl1c
Dec 15 14:36:41 User-PC kernel: [175576.122712]
Dec 15 14:36:41 User-PC kernel: [175576.122769] Pid: 0, comm: kworker/0:0 Tainted: G W 2.6.37-rc5-wl+ #3 1015PE/1016P
Dec 15 14:36:41 User-PC kernel: [175576.123012] EIP: 0060:[<f83edd65>] EFLAGS: 00010283 CPU: 1
Dec 15 14:36:41 User-PC kernel: [175576.123193] EIP is at br_multicast_rcv+0xc95/0xe1c [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.123362] EAX: 0000001c EBX: f5626318 ECX: 00000000 EDX: 00000000
Dec 15 14:36:41 User-PC kernel: [175576.123550] ESI: ec512262 EDI: f5626180 EBP: f60b5ca0 ESP: f60b5bd8
Dec 15 14:36:41 User-PC kernel: [175576.123737] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Dec 15 14:36:41 User-PC kernel: [175576.123902] Process kworker/0:0 (pid: 0, ti=f60b4000 task=f60a8000 task.ti=f60b0000)
Dec 15 14:36:41 User-PC kernel: [175576.124137] Stack:
Dec 15 14:36:41 User-PC kernel: [175576.124181] ec556500f6d06800f60b5be8c01087d8ec5122620000003000000024f5626180
Dec 15 14:36:41 User-PC kernel: [175576.124181] f572c200ef463440f56263003afffffff6d06dd0e60766a4000000c4f6d06860
Dec 15 14:36:41 User-PC kernel: [175576.124181] ffffffffec55652c00000001f6d06844f60b5c64c0138264c016e451c013e47d
Dec 15 14:36:41 User-PC kernel: [175576.124181] Call Trace:
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c01087d8>] ? sched_clock+0x8/0x10
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0138264>] ? enqueue_entity+0x174/0x440
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c016e451>] ? sched_clock_cpu+0x131/0x190
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c013e47d>] ? select_task_rq_fair+0x2ad/0x730
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0524fc1>] ? nf_iterate+0x71/0x90
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e4914>] ? br_handle_frame_finish+0x184/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e4790>] ? br_handle_frame_finish+0x0/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e46e9>] ? br_handle_frame+0x189/0x230 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e4790>] ? br_handle_frame_finish+0x0/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e4560>] ? br_handle_frame+0x0/0x230 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c04ff026>] ? __netif_receive_skb+0x1b6/0x5b0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c04f7a30>] ? skb_copy_bits+0x110/0x210
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0503a7f>] ? netif_receive_skb+0x6f/0x80
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f82cb74c>] ? ieee80211_deliver_skb+0x8c/0x1a0 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f82cc836>] ? ieee80211_rx_handlers+0xeb6/0x1aa0 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c04ff1f0>] ? __netif_receive_skb+0x380/0x5b0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c016e242>] ? sched_clock_local+0xb2/0x190
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c012b688>] ? default_spin_lock_flags+0x8/0x10
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05d83df>] ? _raw_spin_lock_irqsave+0x2f/0x50
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f82cd621>] ? ieee80211_prepare_and_rx_handle+0x201/0xa90 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f82ce154>] ? ieee80211_rx+0x2a4/0x830 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f815a8d6>] ? iwl_update_stats+0xa6/0x2a0 [iwlcore]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f8499212>] ? iwlagn_rx_reply_rx+0x292/0x3b0 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05d83df>] ? _raw_spin_lock_irqsave+0x2f/0x50
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f8483697>] ? iwl_rx_handle+0xe7/0x350 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f8486ab7>] ? iwl_irq_tasklet+0xf7/0x5c0 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c01aece1>] ? __rcu_process_callbacks+0x201/0x2d0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0150d05>] ? tasklet_action+0xc5/0x100
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0150a07>] ? __do_softirq+0x97/0x1d0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05d910c>] ? nmi_stack_correct+0x2f/0x34
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0150970>] ? __do_softirq+0x0/0x1d0
Dec 15 14:36:41 User-PC kernel: [175576.124181] <IRQ>
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c01508f5>] ? irq_exit+0x65/0x70
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05df062>] ? do_IRQ+0x52/0xc0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c01036b0>] ? common_interrupt+0x30/0x38
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c03a1fc2>] ? intel_idle+0xc2/0x160
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c04daebb>] ? cpuidle_idle_call+0x6b/0x100
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0101dea>] ? cpu_idle+0x8a/0xf0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05d2702>] ? start_secondary+0x1e8/0x1ee
Cc: David Miller <davem@davemloft.net> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
J. K. Cliburn [Sat, 1 Jan 2011 05:02:12 +0000 (05:02 +0000)]
atl1: fix oops when changing tx/rx ring params
Commit 3f5a2a713aad28480d86b0add00c68484b54febc zeroes out the statistics
message block (SMB) and coalescing message block (CMB) when adapter ring
resources are freed. This is desirable behavior, but, as a side effect,
the commit leads to an oops when atl1_set_ringparam() attempts to alter
the number of rx or tx elements in the ring buffer (by using ethtool
-G, for example). We don't want SMB or CMB to change during this
operation.
Modify atl1_set_ringparam() to preserve SMB and CMB when changing ring
parameters.
Cc: stable@kernel.org Signed-off-by: Jay Cliburn <jcliburn@gmail.com> Reported-by: Tõnu Raitviir <jussuf@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
The problem was that a temporary page table mapping was being improperly
restored.
The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort. The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0. This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Mike Rapoport [Wed, 29 Dec 2010 07:06:26 +0000 (09:06 +0200)]
ARM: it8152: add IT8152_LAST_IRQ definition to fix build error
The commit 6ac6b817f3f4c23c5febd960d8deb343e13af5f3 (ARM: pxa: encode
IRQ number into .nr_irqs) removed definition of ITE_LAST_IRQ which
caused the following build error:
CC arch/arm/common/it8152.o
arch/arm/common/it8152.c: In function 'it8152_init_irq':
arch/arm/common/it8152.c:86: error: 'IT8152_LAST_IRQ' undeclared (first use in this function)
arch/arm/common/it8152.c:86: error: (Each undeclared identifier is reported only once
arch/arm/common/it8152.c:86: error: for each function it appears in.)
make[2]: *** [arch/arm/common/it8152.o] Error 1
Defining the IT8152_LAST_IRQ in the arch/arm/include/hardware/it8152.c
fixes the build.
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ipchain__fprintf_graph() casts the number of hits in a branch as an
int, which means we lose its highests bits.
This results in meaningless number of callchain hits in perf.data
that have a high number of hits recorded, typically those that have
callchain branches hits appearing more than INT_MAX. This happens
easily as those are pondered by the event period.
Reported-by: Nick Piggin <npiggin@kernel.dk> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Paul Mackerras <paulus@samba.org>
Robert Richter [Mon, 3 Jan 2011 11:15:14 +0000 (12:15 +0100)]
arch/x86/oprofile/op_model_amd.c: Perform initialisation on a single CPU
Disable preemption in init_ibs(). The function only checks the
ibs capabilities and sets up pci devices (if necessary). It runs
only on one cpu but operates with the local APIC and some MSRs,
thus it is better to disable preemption.
[ 7.034377] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/483
[ 7.034385] caller is setup_APIC_eilvt+0x155/0x180
[ 7.034389] Pid: 483, comm: modprobe Not tainted 2.6.37-rc1-20101110+ #1
[ 7.034392] Call Trace:
[ 7.034400] [<ffffffff812a2b72>] debug_smp_processor_id+0xd2/0xf0
[ 7.034404] [<ffffffff8101e985>] setup_APIC_eilvt+0x155/0x180
[ ... ]
Hans Verkuil [Sat, 18 Dec 2010 12:59:51 +0000 (09:59 -0300)]
[media] em28xx: radio_fops should also use unlocked_ioctl
em28xx uses core assisted locking, so it shouldn't use .ioctl.
The .ioctl callback was replaced by .unlocked_ioctl for video nodes,
but not for radio nodes. This is now corrected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] wm8775: Revert changeset fcb9757333 to avoid a regression
It seems that cx88 and ivtv use wm8775 on some different modes. The
patch that added support for a board with wm8775 broke ivtv boards with
this device. As we're too close to release 2.6.37, let's just revert
it.
Reported-by: Andy Walls <awalls@md.metrocast.net> Reported-by: Eric Sharkey <eric@lisaneric.org> Reported-by: Auric <auric@aanet.com.au>
Reported by: David Gesswein <djg@pdp8online.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 5 Dec 2010 22:42:30 +0000 (19:42 -0300)]
[media] cx25840: Prevent device probe failure due to volume control ERANGE error
This patch fixes a regression that crept into 2.6.36.
The volume control scale in the cx25840 driver has an unusual mapping
from register values to v4l2 volume control values. Enforce the mapping
limits, so that the default volume control setting does not fall out of
bounds to prevent the cx25840 module device probe from failing.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Axel Lin [Mon, 3 Jan 2011 01:26:53 +0000 (02:26 +0100)]
ARM: 6605/1: Add missing include "asm/memory.h"
This patch fixes below build error by adding the missing asm/memory.h,
which is needed for arch_is_coherent().
$ make pxa3xx_defconfig; make
CC init/do_mounts_rd.o
In file included from include/linux/list_bl.h:5,
from include/linux/rculist_bl.h:7,
from include/linux/dcache.h:7,
from include/linux/fs.h:381,
from init/do_mounts_rd.c:3:
include/linux/bit_spinlock.h: In function 'bit_spin_unlock':
include/linux/bit_spinlock.h:61: error: implicit declaration of function 'arch_is_coherent'
make[1]: *** [init/do_mounts_rd.o] Error 1
make: *** [init] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Hutchings [Sun, 2 Jan 2011 23:02:42 +0000 (23:02 +0000)]
watchdog: Improve initialisation error message and documentation
The error message 'NMI watchdog failed to create perf event...'
does not make it clear that this is a fatal error for the
watchdog. It also currently prints the error value as a
pointer, rather than extracting the error code with PTR_ERR().
Fix that.
Add a note to the description of the 'nowatchdog' kernel
parameter to associate it with this message.
Reported-by: Cesare Leonardi <celeonar@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: 599368@bugs.debian.org Cc: 608138@bugs.debian.org Cc: Don Zickus <dzickus@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: <stable@kernel.org> # .37.x and later
LKML-Reference: <1294009362.3167.126.camel@localhost> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Sun, 2 Jan 2011 18:37:19 +0000 (10:37 -0800)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kconfig: fix undesirable side effect of adding "visible" menu attribute
Avi Kivity [Fri, 31 Dec 2010 08:52:15 +0000 (10:52 +0200)]
KVM: i8259: initialize isr_ack
isr_ack is never initialized. So, until the first PIC reset, interrupts
may fail to be injected. This can cause Windows XP to fail to boot, as
reported in the fallout from the fix to
https://bugzilla.kernel.org/show_bug.cgi?id=21962.
Reported-and-tested-by: Nicolas Prochazka <prochazka.nicolas@gmail.com> Signed-off-by: Avi Kivity <avi@redhat.com>
projects / karo-tx-linux.git / log