Greg Rose [Thu, 23 Sep 2010 12:46:25 +0000 (12:46 +0000)]
ixgbevf: Refactor ring parameter re-size
The function to resize the Tx/Rx rings had the potential to
dereference a NULL pointer and the code would attempt to resize
the Tx ring even if the Rx ring allocation had failed. This
would cause some confusion in the return code semantics. Fixed
up to just unwind the allocations if any of them fail and return
an error.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the PM support is available this is passed
through the platform instead to be hard-coded
in the core files.
WoL on Magic Frame can be enabled by using
the ethtool support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 20 Sep 2010 20:16:27 +0000 (20:16 +0000)]
ip: take care of last fragment in ip_append_data
While investigating a bit, I found ip_fragment() slow path was taken
because ip_append_data() provides following layout for a send(MTU +
N*(MTU - 20)) syscall :
- one skb with 1500 (mtu) bytes
- N fragments of 1480 (mtu-20) bytes (before adding IP header)
last fragment gets 17 bytes of trail data because of following bit:
if (datalen == length + fraggap)
alloclen += rt->dst.trailer_len;
Then esp4 adds 16 bytes of data (while trailer_len is 17... hmm...
another bug ?)
In ip_fragment(), we notice last fragment is too big (1496 + 20) > mtu,
so we take slow path, building another skb chain.
In order to avoid taking slow path, we should correct ip_append_data()
to make sure last fragment has real trail space, under mtu...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
E1000 can benefit from calling the GRO receive functions.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Net drivers in general have an issue where timers fired
by mod_timer or work threads with schedule_work are running
outside of the rtnl_lock.
With no other lock protection these routines are vulnerable
to races with driver unload or reset paths.
The longer term solution to this might be a redesign with
safer locks being taken in the driver to guarantee no
reentrance, but for now a safe and effective fix is
to take the rtnl_lock in these routines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
E1000 is using several timers that in a follow on patch
will need to acquire the rtnl_lock in order to be safe.
This patch moves the timer bodies into work queues which
will allow the next patch to add rtnl_lock.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Wed, 22 Sep 2010 17:57:58 +0000 (17:57 +0000)]
e1000/e1000e/igb/ixgb/ixgbe: set NETIF_F_HIGHDMA for VLAN feature flags
If the netdev->features is set with NETIF_F_HIGHDMA, we should set the
corresponding netdev->vlan_features as well to allow VLAN netdev created
on top of the real netdev to be able to also benefit from HIGHDMA on 32bit
system, reducing the performance hit that is caused by __skb_linearize(),
particularly for large send. This is fixed in this patch for all Intel e1000,
e1000e, igb, ixgbe, and ixgbe drivers since this should be beneficial
to all devices supported by these drivers.
Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Intel(r) DH89xxCC series. The new
device will be using Intel(r) i347-AT4 and Marvell(r) M88E1322 and
M88E1112 PHYs. Support for these devices has also been added here.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 22 Sep 2010 17:56:20 +0000 (17:56 +0000)]
igb: clear VF_PROMISC bits instead of setting all other bits
This change corrects an issue in which we were setting all flag bits except
for promisc instead of clearing the promisc bits due to the incorrect use
of an |= instead of an &=.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Mon, 20 Sep 2010 20:40:24 +0000 (20:40 +0000)]
drivers: atm: use native kernel's hex_to_bin() func
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Chas Williams <chas@cmf.nrl.navy.mil> Cc: linux-atm-general@lists.sourceforge.net Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 21 Sep 2010 23:12:11 +0000 (16:12 -0700)]
ethtool: Fix build due to lack of ethtool.h include.
net/core/ethtool.c: In function 'ethtool_get_regs':
net/core/ethtool.c:818:2: error: implicit declaration of function 'vmalloc'
net/core/ethtool.c:818:9: warning: assignment makes pointer from integer without a cast
net/core/ethtool.c:833:2: error: implicit declaration of function 'vfree'
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 21 Sep 2010 23:11:06 +0000 (16:11 -0700)]
sfc: Fix build due to lack of vmalloc.h include.
drivers/net/sfc/filter.c: In function ‘efx_probe_filters’:
drivers/net/sfc/filter.c:422: error: implicit declaration of function ‘vmalloc’
drivers/net/sfc/filter.c:422: warning: assignment makes pointer from integer without a cast
drivers/net/sfc/filter.c: In function ‘efx_remove_filters’:
drivers/net/sfc/filter.c:442: error: implicit declaration of function ‘vfree’
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Mon, 20 Sep 2010 11:45:38 +0000 (13:45 +0200)]
ath9k: clean up / fix aggregation session flush
The tid aggregation cleanup is a bit fragile, as it discards failed
subframes in some places, and retransmits them in others. This could
block the cleanup of an existing aggregation session, if a retransmission
for a tid is issued, yet the tid is never scheduled again because of
the cleanup state.
Fix this by getting rid of as many subframes as possible, as early
as possible, and immediately transmitting pending subframes as regular
HT frames instead of waiting for the cleanup to complete.
Drop all pending subframes while keeping track of the Block ACK window
during aggregate tx completion to prevent sending out stale subframes,
which could confuse the receiver side.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 20 Sep 2010 17:35:28 +0000 (19:35 +0200)]
ath9k: fix an aggregation start related race condition
A new aggregation session start can be issued by mac80211, even when the
cleanup of the previous session has not completed yet. Since the data structure
for the session is not recreated, this could corrupt the block ack window
and lock up the aggregation session. Fix this by delaying the new session
until the old one has been cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 20 Sep 2010 11:45:36 +0000 (13:45 +0200)]
ath9k: clean up block ack window handling
There's no reason to keep pointers to pending tx buffers around, if they're
only used to keep track of which frames are still pending. Use a bitfield
instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: reinit phy after HT settings have changed
The driver has a set of different initvals for 20 MHz
vs dynamic HT2040 operation. Because we can't change
some of the registers "in-flight", the driver needs to
perform a warm reset.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mark the device as completely dead just yet.
If all goes to plan and carl9170_reboot succeeds
then we can skip the expensive userspace-driven
reinitialization anyway.
And if it doesn't and carl9170_reboot fails,
then carl9170_usb_cancel_urbs will do the
necessary steps.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since carl9170 gained support to read the noisefloor,
the reported noisefloor level was pretty poor.
Initially I assumed that something was wrong in the PHY
setup and it would be impossible to fix without any
guidances. But this was not the case. In fact the nf
readings were correct and the thing that was broken
was the "simple" sign extension code!
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:37:12 +0000 (11:37 +0900)]
ath5k: Simplify cw_min/max and AIFS configuration
Get rid of overly complicated cw_min/max and AIFS configuration:
* Validate values in ath5k_hw_set_tx_queueprops(), so we can use them directly
without further checks or computation in ath5k_hw_reset_tx_queue().
* Simplifiy by using AR5K_TUNE_AIFS|CWMIN|CWMAX variables directly since we
don't support XR or B channels. That way we can also remove
AR5K_TXQ_USEDEFAULT and the confusing logic around it.
* Update data types: AIFS is u8, CW's are u16.
* Remove now unneeded variables in ath5k_hw.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:37:07 +0000 (11:37 +0900)]
ath5k: Keep last descriptor in queue
If we return a TX descriptor to the pool of available descriptors, while a
queues TXDP still points to it we could potentially run into all sorts of
troube.
It has been suggested that there is hardware which can set the descriptors
done bit before it reads ds_link and moves on to the next descriptor. While the
documentation says this is not true for newer chipsets (the descriptor contents
are copied to some internal memory), we don't know about older hardware.
To be safe, we always keep the last descriptor in the queue, and avoid dangling
TXDP pointers. Unfortunately this does not fully resolve the problem - queues
still get stuck!
This is similar to what ath9k does.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:36:56 +0000 (11:36 +0900)]
ath5k: Add watchdog for stuck TX queues
Since we do not know any better solution to the problem that TX queues can get
stuck, this adds a timer-based watchdog, which will check for stuck queues and
reset the hardware if necessary.
Bruno Randolf [Fri, 17 Sep 2010 02:36:35 +0000 (11:36 +0900)]
ath5k: Use four hardware queues
Prepare ath5k for WME by using four hardware queues.
The way we set up our queues matches the mac80211 queue priority 1:1, so we
don't have to do any mapping for queue numbers.
Every queue uses 50 of the total 200 available transmit buffers, so the DMA
memory usage does not increase with this patch, but it might be good to
fine-tune the number of buffers per queue later (depending on the CPU speed and
load, and the speed of the medium access, it might not be big enough).
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Fri, 17 Sep 2010 03:45:07 +0000 (12:45 +0900)]
ath5k: reorder base.c to remove fwd decls
This change reorganizes the main ath5k file in order to re-group
related functions and remove most of the forward declarations
(from 61 down to 3). This is, unfortunately, a lot of churn, but
there should be no functional changes.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unneeded ath_crypt_caps flags, as per "ath9k_hw: remove useless hw
capability flags" (364734fafbba0c3133e482db78149b9a823ae7a5), but set the
AESCCM flag for ath9k. common ath code still needs a flag for this because
there is ath5k hardware which can't do AES in hardware.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a simple mechanism to pass platform data to the
SDIO instances of wl12xx.
This way there is no confusion over who owns the 'embedded data',
typechecking is preserved, and no possibility for the wrong driver to
pick up the data.
Originally proposed by Russell King.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it possible for the set power method to indicate a
success/failure return value. This is needed to support
more complex power on/off operations such as SDIO
power manipulations.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Acked-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The `options_received' struct is redundant, since it re-duplicates the existing
`p' and `x_recv' fields. This patch removes the sub-struct and migrates the
format conversion operations to ccid3_hc_tx_parse_options().
dccp tfrc/ccid-3: computing the loss rate from the Loss Event Rate
This adds a function to take care of the following, separate cases occurring in
the computation of the Loss Rate p:
* 1/(2^32-1) is mapped into 0% as per RFC 4342, 8.5;
* 1/0 is mapped into 100%, the maximum;
* to avoid that p = 1/x is rounded down to 0 when x is very large, since this
means accidentally re-entering slow-start indicated by p == 0, the minimum
resolution value of p is now returned instead;
* a bug in ccid3_hc_rx_getsockopt is fixed: 1/0 was mapped into ~0U.
This patch is thanks to an investigation by Leandro Sales de Melo and his
colleagues. They worked out two state diagrams which highlight the fact that
the xxx_TERM states in CCID-3/4 are in fact not necessary.
And this can be confirmed by in turn looking at the code: the xxx_TERM states
are only ever set in ccid3_hc_{rx,tx}_exit(): when CCID-3 sets the state
to xxx_TERM, it is at a time where no more processing should be going on,
hence it is not necessary to introduce a dedicated exit state - this is already
implied by unloading the CCID.
dccp: Add packet type information to CCID-specific option parsing
This
1. adds packet type information to ccid_hc_{rx,tx}_parse_options(). This is
necessary, since table 3 in RFC 4340, 5.8 leaves it to the CCIDs to state
which options may (not) appear on what packet type.
2. adds such a check for CCID-3's {Loss Event, Receive} Rate as specified in
RFC 4340 8.3 ("Receive Rate options MUST NOT be sent on DCCP-Data packets")
and 8.5 ("Loss Event Rate options MUST NOT be sent on DCCP-Data packets").
3. removes an unused argument `idx' from ccid_hc_{rx,tx}_parse_options(). This
is also no longer necessary, since the CCID-specific option-parsing routines
are passed every single parameter of the type-length-value option encoding.
Eric Dumazet [Mon, 20 Sep 2010 00:12:11 +0000 (00:12 +0000)]
net: rx_dropped accounting
Under load, netif_rx() can drop incoming packets but administrators dont
have a chance to spot which device needs some tuning (RPS activation for
example)
This patch adds rx_dropped accounting in vlans and tunnels.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bandan Das [Sun, 19 Sep 2010 09:34:33 +0000 (09:34 +0000)]
bridge : Sanitize skb before it enters the IP stack
Related dicussion here : http://lkml.org/lkml/2010/9/3/16
Introduce a function br_parse_ip_options that will audit the
skb and possibly refill IP options before a packet enters the
IP stack. If no options are present, the function will zero out
the skb cb area so that it is not misinterpreted as options by some
unsuspecting IP layer routine. If packet consistency fails, drop it.
Signed-off-by: Bandan Das <bandan.das@stratus.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Sat, 18 Sep 2010 13:44:14 +0000 (13:44 +0000)]
rds: spin_lock_irq() is not nestable
This is basically just a cleanup. IRQs were disabled on the previous
line so we don't need to do it again here. In the current code IRQs
would get turned on one line earlier than intended.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 16 Sep 2010 11:28:07 +0000 (11:28 +0000)]
ethtool, ixgbe: Move RX n-tuple mask fixup to ethtool
The ethtool utility does not set masks for flow parameters that are
not specified, so if both value and mask are 0 then this must be
treated as equivalent to a mask with all bits set. Currently that is
done in the only driver that implements RX n-tuple filtering, ixgbe.
Move it to the ethtool core.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Lamparter [Fri, 17 Sep 2010 03:22:19 +0000 (03:22 +0000)]
netns: keep vlan slaves on master netns move
previously, if a vlan master device was moved from one network namespace
to another, all 802.1q and macvlan slaves were deleted.
we can use dev->reg_state to figure out whether dev_change_net_namespace
is happening, since that won't set dev->reg_state NETREG_UNREGISTERING.
so, this changes 8021q and macvlan to ignore NETDEV_UNREGISTER when
reg_state is not NETREG_UNREGISTERING.
Signed-off-by: David Lamparter <equinox@diac24.net> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Daniel Lezcano <daniel.lezcano@free.fr> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: prevent dma init stuck in case of failures.
Add a limit when perform the DMA reset procedure
so, in case of problems (i.e. PHY reset failed) the
Kernel won't hang on the stmmac DMA initialisation
blocking the Kernels execution.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The first version of the driver had hard-coded the logic
for handling the checksum offloading.
This was designed according to the chips included in
the STM platforms where:
o MAC10/100 supports no COE at all.
o GMAC fully supports RX/TX COE.
This is not good for other chip configurations where,
for example, the mac10/100 supports the tx csum in HW
or when the GMAC has no IPC.
Thanks to Johannes Stezenbach; he provided me a first
draft of this patch that only reviewed the IPC for the
GMAC devices.
This patch also helps on SPEAr platforms where the
MAC10/100 can perform the TX csum in HW.
Thanks to Deepak SIKRI for his support on this.
In the end, GMAC devices for STM platforms have
a bugged Jumbo frame support that needs to have
the Tx COE disabled for oversized frames (due to
limited buffer sizes). This information is also
passed through the driver's platform structure.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Johannes Stezenbach <js@sig21.net> Signed-off-by: Deepak SIKRI <deepak.sikri@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Original patch from Johannes Stezenbach fixed the CSR
in the stmmac_mdio. We agreed to provide this through
the platform instead of.
Also thanks to Johannes for having tested it on ARM.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Johannes Stezenbach <js@sig21.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Sternberg [Wed, 8 Sep 2010 16:42:35 +0000 (09:42 -0700)]
iwlwifi: corrections to debug output of ucode statistics
remove duplicate header and clean up format so it is defined once
making changes consolicated ensuring consistancy of output.
no function change to date displayed.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
projects / linux-beck.git / log