York Sun [Sat, 29 Sep 2012 23:44:35 +0000 (16:44 -0700)]
powerpc/mpc85xx: Change spin table to cached memory
ePAPR v1.1 requires the spin table to be in cached memory. So we need
to change the call argument of ioremap to enable cache and coherence.
We also flush the cache after writing to spin table to keep it compatible
with previous cache-inhibit spin table. Flushing before and after
accessing spin table is recommended by ePAPR.
Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jia Hongtao [Thu, 8 Nov 2012 02:11:07 +0000 (10:11 +0800)]
powerpc/fsl-pci: Add PCI controller ATMU PM support
Power supply for PCI controller ATMU registers is off when system go to
deep-sleep state. So ATMU registers should be re-setup during PCI
controllers resume from sleep.
Signed-off-by: Jia Hongtao <B38951@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Function fsl_pcibios_fixup_bus() is available only if PCI is enabled. The
MPC8610 HPCD platform file was not protecting the assigned with an #ifdef,
which results in a link failure when PCI is disabled. Every other platform
already has this #ifdef.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Thu, 17 May 2012 19:10:27 +0000 (14:10 -0500)]
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
The MSR[GS] bit indicates whether the kernel is running in processor guest
state mode, but such a check is unnecessary. The driver already checks
for the /hypervisor node and the fsl,hv-version property, so it already
knows that it's running under the Freescale hypervisor.
There is nothing in the driver that inherently requires guest state,
anyway.
This fixes a break that can occur in some randconfig builds.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ian Munsie [Thu, 8 Nov 2012 05:40:28 +0000 (16:40 +1100)]
powerpc: Disable relocation on exceptions when kexecing
Since we don't know if they new kernel we are kexecing into has been
built to support relocation on exceptions, we disable them before we
kexec.
We do NOT disable them if we are execing a kdump kernel, because we
want to change as little state as possible and it is likely that we are
execing ourselves and will be able to handle them anyway.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ian Munsie [Thu, 8 Nov 2012 05:03:14 +0000 (16:03 +1100)]
powerpc: Enable relocation on during exceptions at boot
We currently do this synchronously at boot from setup_arch. On a large
system this could hypothetically take a little while to complete, so
currently we will give up if we are asked to wait for more than a second
in total.
If we actually start hitting that timeout in practice we can always move
this code into a kernel thread to take care of it in the background.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ian Munsie [Thu, 8 Nov 2012 05:10:29 +0000 (16:10 +1100)]
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
I am going to use this in the next patch, better to have this code in
one place rather than three.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ian Munsie [Thu, 8 Nov 2012 04:57:04 +0000 (15:57 +1100)]
powerpc: Add wrappers to enable/disable relocation on exceptions
These wrappers hide the parameters that have to be passed to H_SET_MODE
to enable/disable relocation on during exceptions.
As noted in the comments, since these have partition wide scope, they
may take some time to complete and must be periodically retried until
H_SUCCESS is returned.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ian Munsie [Tue, 6 Nov 2012 05:15:17 +0000 (16:15 +1100)]
powerpc: Add set_mode hcall
This new hcall in POWER8 is used to set various resource mode registers.
eg. it can set address translation mode on interrupt (note: partition wide
scope)
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Fri, 2 Nov 2012 05:41:58 +0000 (16:41 +1100)]
powerpc: Setup relocation on exceptions for bare metal systems
This turns on MMU on execptions via AIL field in the LPCR.
Signed-off-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 5 Nov 2012 03:40:18 +0000 (14:40 +1100)]
powerpc: Move initial mfspr LPCR out of __init_LPCR
We want to change what's initially set in the LPCR, so start by taking the move
from LPCR out of the function and into the caller.
Signed-off-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Fri, 2 Nov 2012 06:21:43 +0000 (17:21 +1100)]
powerpc: Add relocation on exception vector handlers
POWER8/v2.07 allows exceptions to be taken with the MMU still on.
A new set of exception vectors is added at 0xc000_0000_0000_4xxx. When the HW
takes us here, MSR IR/DR will be set already and we no longer need a costly
RFID to turn the MMU back on again.
The original 0x0 based exception vectors remain for when the HW can't leave the
MMU on. Examples of this are when we can't trust the current MMU mappings,
like when we are changing from guest to hypervisor (HV 0 -> 1) or when the MMU
was off already. In these cases the HW will take us to the original 0x0 based
exception vectors with the MMU off as before.
This uses the new macros added previously too implement these new execption
vectors at 0xc000_0000_0000_4xxx. We exit these exception vectors using
mflr/blr (rather than mtspr SSR0/RFID), since we don't need the costly MMU
switch anymore.
This moves the __end_interrupts marker down past these new 0x4000 vectors since
they will need to be copied down to 0x0 when the kernel is not at 0x0.
Signed-off-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Fri, 2 Nov 2012 06:21:28 +0000 (17:21 +1100)]
powerpc: Add new macros needed for relocation on exceptions
POWER8/v2.07 allows exceptions to be taken with the MMU still on.
A new set of exception vectors is added at 0xc000_0000_0000_4xxx. When the HW
takes us here, MSR IR/DR will be set already and we no longer need a costly
RFID to turn the MMU back on again.
The original 0x0 based exception vectors remain for when the HW can't leave the
MMU on. Examples of this are when we can't trust the current the MMU mappings,
like when we are changing from guest to hypervisor (HV 0 -> 1) or when the MMU
was off already. In these cases the HW will take us to the original 0x0 based
exception vectors with the MMU off as before.
The below macros are copies of the macros used at the 0x0 offset but modified
to handle the MMU being on. In these macros we use the link register to jump
to the secondary handlers rather than using RFID (RFID was also use to turn on
the MMU).
Signed-off-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Fri, 2 Nov 2012 06:16:01 +0000 (17:16 +1100)]
powerpc: Turn syscall handler into macros
This turns the syscall handler into macros as we are going to want to reuse
them again later.
Signed-off-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we build a kernel with CONFIG_RELOCATABLE=y CONFIG_CRASH_DUMP=n,
the kernel fails when we run at a non zero offset. It turns out
we were incorrectly wrapping some of the relocatable kernel code
with CONFIG_CRASH_DUMP.
Signed-off-by: Anton Blanchard <anton@samba.org> Cc: <stable@kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
JoonSoo Kim [Mon, 12 Nov 2012 06:40:33 +0000 (06:40 +0000)]
powerpc: Change free_bootmem() to kfree()
commit ea96025a('Don't use alloc_bootmem() in init_IRQ() path')
changed alloc_bootmem() to kzalloc(),
but missed to change free_bootmem() to kfree().
So correct it.
Signed-off-by: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aravinda Prasad [Sun, 4 Nov 2012 22:15:28 +0000 (22:15 +0000)]
powerpc/ptrace: Enable hardware breakpoint upon re-registering
On powerpc, ptrace will disable hardware breakpoint request once the
breakpoint is hit. It is the responsibility of the caller to set it
again. However, when the caller sets the hardware breakpoint again
using ptrace(PTRACE_SET_DEBUGREG, child_pid, 0, addr), the hardware
breakpoint is not enabled.
While gdb's approach is to unregister and re-register the hardware
breakpoint every time the breakpoint is hit - which is working fine,
this could affect other programs trying to re-register hardware
breakpoint without unregistering.
This patch enables hardware breakpoint if the caller is re-registering.
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com> Acked-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Akinobu Mita [Sun, 4 Nov 2012 02:03:45 +0000 (02:03 +0000)]
powerpc: Use asm-generic/bitops/le.h
The only difference between powerpc and asm-generic le-bitops is
test_bit_le(). Usually all bitops require a long aligned bitmap.
But powerpc test_bit_le() can take an unaligned address.
There is no special callsite of test_bit_le() that needs unaligned
access in powerpc as far as I can see. So convert to use
asm-generic/bitops/le.h for powerpc.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Akinobu Mita [Sun, 4 Nov 2012 02:03:44 +0000 (02:03 +0000)]
powerpc: Remove BITOP_MASK and BITOP_WORD from asm/bitops.h
Replace BITOP_MASK and BITOP_WORD with BIT_MASK and BIT_WORD defined
in linux/bitops.h and remove BITOP_* which are not used anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Akinobu Mita [Sun, 4 Nov 2012 02:03:43 +0000 (02:03 +0000)]
powerpc/iommu: Use bitmap library
- Caluculate the bitmap size with BITS_TO_LONGS()
- Use bitmap_empty() to verify that all bits are cleared
This also includes a printk to pr_warn() conversion.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Yang Li [Thu, 1 Nov 2012 18:53:42 +0000 (18:53 +0000)]
powerpc: Fix typos in Freescale copyright claims
There are many cases that Semiconductor is misspelled. The patch
fix these typos.
Signed-off-by: Li Yang <leoli@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Thu, 1 Nov 2012 14:55:04 +0000 (14:55 +0000)]
powerpc: Move most of setup.h out of uapi
Most of setup.h should not be exported to userspace, so move it
back. All we are left with is the asm-generic include to pick
up the COMMAND_LINE_SIZE define.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Tue, 30 Oct 2012 16:09:56 +0000 (16:09 +0000)]
powerpc/perf: Add missing L2 constraint handling in Power7 PMU
If we have two cache events that require different settings of the L2SEL
bits in MMCR1 then we can not schedule those events simultaneously. Add
logic to the constraint handling to express that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Andreas Schwab [Sun, 28 Oct 2012 23:15:14 +0000 (23:15 +0000)]
powerpc/powermac/cpufreq_32: Set non-infinite transition time for 7447A driver
The transition time for the 7447A is around 8ms which makes it possible
to use the ondemand governor. This has been tested on the iBook G4
(PowerBook6,7).
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Tested-by: Michel Dänzer <michel@daenzer.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
K.Prasad [Sun, 28 Oct 2012 15:13:15 +0000 (15:13 +0000)]
powerpc/hw-breakpoint: Use generic hw-breakpoint interfaces for new PPC ptrace flags
PPC_PTRACE_GETHWDBGINFO, PPC_PTRACE_SETHWDEBUG and PPC_PTRACE_DELHWDEBUG are
PowerPC specific ptrace flags that use the watchpoint register. While they are
targeted primarily towards BookE users, user-space applications such as GDB
have started using them for BookS too. This patch enables the use of generic
hardware breakpoint interfaces for these new flags.
Apart from the usual benefits of using generic hw-breakpoint interfaces, these
changes allow debuggers (such as GDB) to use a common set of ptrace flags for
their watchpoint needs and allow more precise breakpoint specification (length
of the variable can be specified).
Mikey added: rebased and added dbginfo.features around #ifdef
CONFIG_HAVE_HW_BREAKPOINT
Signed-off-by: K.Prasad <prasad@linux.vnet.ibm.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL provides the firmware base/entry in registers at boot time
for debugging purposes. We had a bug in the code trying to stash
these into the appropriate kernel globals (a line of code was
probably dropped by accident back when this was merged)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Julia Lawall [Sun, 21 Oct 2012 00:52:05 +0000 (00:52 +0000)]
powerpc/rtas_flash: Eliminate possible double free
The function initialize_flash_pde_data is only called four times. All four
calls are in the function rtas_flash_init, and on the failure of any of the
calls, remove_flash_pde is called on the third argument of each of the
calls. There is thus no need for initialize_flash_pde_data to call
remove_flash_pde on the same argument. remove_flash_pde kfrees the data
field of its argument, and does not clear that field, so this amounts ot a
possible double free.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
Gavin Shan [Wed, 17 Oct 2012 19:53:30 +0000 (19:53 +0000)]
powerpc/pnv: Avoid bogus output
There're couples of functions defined to print debugging messages
during initializing P7IOC. However, we got bogus output from those
functions like pe_info(). The problem here is that the message
level (the first parameter to printk()) isn't printable and that
caused the bogus output.
The patch fixes the issue by merging __pe_printk() to the macro
define_pe_printk_level() so that we can pass the message level
directly to printk().
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/xmon: Fallback to printk() in xmon_printf() if udbg is not setup
It is possible to configure a kernel which has xmon enabled, but has no
udbg backend to provide IO. This can make xmon rather confusing, as it
produces no output, blocks for two seconds, and then returns.
As a last resort we can instead try to printk(), which may deadlock or
otherwise crash, but tries quite hard not to.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/xmon: Fiddle xmon_depth_to_print logic in xmon_show_stack()
Currently xmon_depth_to_print is static and global, but it's only
ever used in xmon_show_stack().
At least with a modern compiler it's inlined, so there's no point
in it being static, we could #define it but it's only used in one
place.
By reworking the logic we can drop count and just decrement the
max value as a loop counter. Also switch to a while loop so we
actually print no more than 64 frames as you'd expect based on the
variable name.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The routines in start.c are only ever called from nonstdio.c, so if we
move them in there they can become static which is nice.
I suspect the idea behind the separation was that start.c could be
replaced in order to build xmon in userland. If anyone still cares about
doing that we could handle that with an ifdef or two.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dan Horák [Wed, 12 Sep 2012 06:06:44 +0000 (06:06 +0000)]
fbdev: Add GXT4000P and GXT6500P support to the gxt4500 driver
I'm reviving an old patch from 2009 that adds support for GXT4000P and GXT6500P
adapter to the gxt4500 driver.
See threads at http://marc.info/?l=linux-fbdev-devel&m=124345080216952&w=2
and https://lists.ozlabs.org/pipermail/linuxppc-dev/2009-June/072672.html
for more details.
This patch adds support for GXT4000P and GXT6500P cards found on some
IBM pSeries machines.
GXT4000P/6000P and GXT4500P/6500P couples are identical from
software's point of view and are based on the same Raster Engine
(RC1000), except for a different reference clock for the PLL.
GXT6x00P models are equipped with an additional Geometry Engine
(GT1000) but this driver doesn't use it.
Signed-off-by: Nico Macrionitis <acrux@cruxppc.org> Signed-off-by: Giuseppe Coviello <cjg@cruxppc.org> Tested-by: Dan Horák <dan@danny.cz> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Tue, 2 Oct 2012 16:59:39 +0000 (16:59 +0000)]
powerpc+of: Remove the pSeries_reconfig.h file
Remove the pSeries_reconfig.h header file. At this point there is only one
definition in the file, pSeries_coalesce_init(), which can be
moved to rtas.h.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Tue, 2 Oct 2012 16:57:57 +0000 (16:57 +0000)]
powerpc+of: Add of node/property notification chain for adds and removes
This patch moves the notification chain for updates to the device tree
from the powerpc/pseries code to the base OF code. This makes this
functionality available to all architectures.
Additionally the notification chain is updated to allow notifications
for property add/remove/update. To make this work a pointer to a new
struct (of_prop_reconfig) is passed to the routines in the notification chain.
The of_prop_reconfig property contains a pointer to the node containing the
property and a pointer to the property itself. In the case of property
updates, the property pointer refers to the new property.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Tue, 2 Oct 2012 16:55:01 +0000 (16:55 +0000)]
powerpc+of: Add /proc device tree updating to of node add/remove
When adding or removing a device tree node we should also update
the device tree in /proc/device-tree. This action is already done in the
generic OF code for adding/removing properties of a node. This patch adds
this functionality for nodes.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Deepthi Dharwar [Wed, 3 Oct 2012 18:42:26 +0000 (18:42 +0000)]
cpuidle/powerpc: Fix snooze state problem in the cpuidle design on pseries.
Earlier without cpuidle framework on pseries, the native arch
idle routine comprised of both snooze and nap
states. smt_snooze_delay variable was used to delay
the idle process entry to deeper idle state like nap.
With the coming of cpuidle, this arch specific idle was replaced
by two different idle routines, one for supporting snooze and other
for nap. This enabled addition of more
low level idle states on pseries in the future.
On adopting the generic cpuidle framework for POWER systems,
the decision of which idle state to choose from, given a predicted
idle time is taken by the menu governor based on
target_residency and exit_latency of the idle states.
target_residency is the minimum time to be resident in that idle state.
Exit_latency is time taken to exit out of idle state.
Deeper the idle state, both the target residency and exit latency
would be higher.
In the current design, smt_snooze_delay is used as target_residency
for the snooze state which is incorrect, as it is not the
minimum but the maximum duration to be in snooze state.
This would result in the governor in taking bad decision,
as presently target_residency of nap < target_residency of snooze
inspite of nap being deeper idle state.
This patch aims to fix this problem by replacing the smt_snooze_delay loop
in snooze state, with the need_resched() as the governor is aware of
entry and exit of various idle transitions based on which
next idle time prediction.
The governor is intelligent enough to determine the idle state the needs to
be transitioned to and maintains a whole of heuristics including
io load, previous idle states predictions etc for the same, based on
which idle state entry decision is taken.
With this fix, of setting target_residency of snooze to 0
nap to smt_snooze_delay
if the predicted idle time is less
than smt_snooze_delay (target_residency of nap)
value governor would pick snooze state, else nap. This adhers to the
previous native idle design.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
smt_snooze_delay was designed to delay idle loop's nap entry
in the native idle code before it got ported over to use as part of
the cpuidle framework.
A -ve value assigned to smt_snooze_delay should result in
busy looping, in other words disabling the entry to nap state.
This particular functionality can be achieved currently by
echo 1 > /sys/devices/system/cpu/cpu*/state1/disable
but it is broken when one assigns -ve value to the smt_snooze_delay
variable either via sysfs entry or ppc64_cpu util.
This patch aims to fix this, by disabling nap state when smt_snooze_delay
variable is set to -ve value.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Deepthi Dharwar [Wed, 3 Oct 2012 18:42:10 +0000 (18:42 +0000)]
cpuidle/powerpc: Fix target residency initialisation in pseries cpuidle
Remove the redundant target residency initialisation in pseries_cpuidle_driver_init().
This is currently over-writing the residency time updated as part of the static
table, resulting in all the idle states having the same target
residency of 100us which is incorrect. This may result in the menu governor making
wrong state decisions.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix build failure for powerpc KVM by adding missing VPN_SHIFT definition
and the ';'
arch/powerpc/kvm/book3s_32_mmu_host.c: In function 'kvmppc_mmu_map_page':
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: 'VPN_SHIFT' undeclared (first use in this function)
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: (Each undeclared identifier is reported only once
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: for each function it appears in.)
arch/powerpc/kvm/book3s_32_mmu_host.c:178: error: expected ';' before 'next_pteg'
arch/powerpc/kvm/book3s_32_mmu_host.c:190: error: label 'next_pteg' used but not defined
make[1]: *** [arch/powerpc/kvm/book3s_32_mmu_host.o] Error 1
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull sparc fixes from David Miller:
"Two sparc64 perf bug fixes and add a sysrq facility so I can diagnose
these kinds of problems more quickly in the future."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix bit twiddling in sparc_pmu_enable_event().
sparc64: Add global PMU register dumping via sysrq.
sparc64: Like x86 we should check current->mm during perf backtrace generation.
Linus Torvalds [Wed, 17 Oct 2012 02:24:00 +0000 (19:24 -0700)]
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt.
The bulk of this is the UAPI disintegration for SH.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix up more fallout from pointless ARM __iomem churn.
sh: Wire up kcmp syscall.
UAPI: (Scripted) Disintegrate arch/sh/include/asm
David Howells [Mon, 15 Oct 2012 23:10:35 +0000 (00:10 +0100)]
FRV: Fix linux/elf-fdpic.h
It seems I accidentally switched the guard on linux/elf-fdpic.h from #ifdef
__KERNEL__ to #ifndef __KERNEL__ when attempting to expand the guarded region
to cover the elf_fdpic_params struct when doing the UAPI split - with the
result that the struct became unavailable to kernel code.
Move incorrectly guarded bits back to the kernelspace header.
Whilst we're at it, the __KERNEL__ guards can be deleted as they're no longer
necessary.
Andi Kleen [Mon, 15 Oct 2012 23:10:28 +0000 (00:10 +0100)]
FRV: Fix const sections change
Add __pminitconst to fix the build, otherwise the following error can occur:
arch/frv/kernel/setup.c:187:47: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
arch/frv/kernel/setup.c:386:2: error: 'clock_cmodes' undeclared (first use in this function)
arch/frv/kernel/setup.c:571:6: error: 'clock_cmodes' undeclared (first use in this function)
make[2]: *** [arch/frv/kernel/setup.o] Error 1
David Howells [Mon, 15 Oct 2012 23:10:21 +0000 (00:10 +0100)]
FRV: Fix incorrect symbol in copy_thread()
Fix an incorrect symbol in copy_thread():
arch/frv/kernel/process.c: In function 'copy_thread':
arch/frv/kernel/process.c:197: error: 'chilregs' undeclared (first use in this function)
arch/frv/kernel/process.c:197: error: (Each undeclared identifier is reported only once
arch/frv/kernel/process.c:197: error: for each function it appears in.)
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When packing CALLL with OR, CALLL must go in the first slot. The
instructions are executed simultaneously, so it doesn't matter which way
round they're packed from that point of view.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul E. McKenney [Tue, 16 Oct 2012 04:35:59 +0000 (21:35 -0700)]
printk: Fix scheduling-while-atomic problem in console_cpu_notify()
The console_cpu_notify() function runs with interrupts disabled in the
CPU_DYING case. It therefore cannot block, for example, as will happen
when it calls console_lock(). Therefore, remove the CPU_DYING leg of
the switch statement to avoid this problem.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
nouveau: fix warning on 32-bit build.
drm/nouveau/bios: fix typo in error message
drm/nouveau: only call ttm_agp_tt_create when __OS_HAS_AGP
drm/nv50/fb: fix double free of vram mm
drm/nouveau/pm: do not stop reclocking if failing to set the fan speed
drm/nouveau/pm: fix a typo related to the move to the therm subdev
drm/nouveau/hwmon: fix the initialization condition
drm: fix warning on 32-bit.
drm: radeon: fix printk format warning
drm/radeon: fix spelling typos in debugging output
drm/radeon: Don't destroy I2C Bus Rec in radeon_ext_tmds_enc_destroy().
drm/radeon: check if pcie gen 2 is already enabled (v2)
drm/radeon/cayman: set VM max pfn at MC init
drm/radeon: separate pt alloc from lru add
drm/radeon: don't add the IB pool to all VMs v2
drm/radeon: allocate page tables on demand v4
drm/radeon: update comments to clarify VM setup (v2)
drm/radeon: allocate PPLLs from low to high
drm/radeon: fix compilation with backlight disabled
drm/radeon: use %zu for formatting size_t
...
Linus Torvalds [Wed, 17 Oct 2012 01:12:38 +0000 (18:12 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull ext2, ext3, quota fixes from Jan Kara:
"Fix three regressions caused by user namespace conversions (ext2,
ext3, quota) and minor ext3 fix and cleanup."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: Silence warning about PRJQUOTA not being handled in need_print_warning()
ext3: fix return values on parse_options() failure
ext2: fix return values on parse_options() failure
ext3: ext3_bread usage audit
ext3: fix possible non-initialized variable on htree_dirblock_to_tree()
Linus Torvalds [Wed, 17 Oct 2012 01:11:48 +0000 (18:11 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Fix for my braino in replace_fd(), dhowell's fix for the fallout from
over-enthusiastic bo^Wdeclaration movements plus crapectomy that
should've happened a long time ago (SEL_... definitions)."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
bury SEL_{IN,OUT,EX}
Unexport some bits of linux/fs.h
fix a leak in replace_fd() users
Linus Torvalds [Wed, 17 Oct 2012 01:10:26 +0000 (18:10 -0700)]
Merge tag 'pinctrl-fixes-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"A number of pinctrl fixes for the v3.7 series:
- duplicate includes, section markup, code mishaps
- erroneous return value in errorpath on the bcm2835 driver
- remove an unused sirf function that was causing build errors
- multiple-platform compilation stubs and a missed code review
comment fixup on the nomadik pin controller"
* tag 'pinctrl-fixes-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: always use the simple irqdomain
pinctrl/nomadik: provide stubs for legacy Nomadik
pinctrl: remove duplicated include from pinctrl-xway.c
pinctrl: sirf: remove sirfsoc_gpio_set_pull function
pinctrl: fix return value in bcm2835_pinctrl_probe()
pinctrl: remove duplicated include from pinctrl-bcm2835.c
pinctrl: bcm2835: Use existing pointer to struct device
pinctrl: samsung: use __devinit section for init code
Linus Torvalds [Wed, 17 Oct 2012 01:08:21 +0000 (18:08 -0700)]
Merge branch 'ipmi' (IPMI patches from Corey Minyard)
Merge emailed patches from Corey Minyard:
"Remove some bogus docs, Fix ACPI/IPMI interactions, fix some warnings,
and add register spacing detection for PCI interfaces."
* ipmi:
IPMI: Detect register spacing on PCI interfaces
IPMI: Fix some uninitialized warning
IPMI: Change link order
ACPI: Reorder IPMI driver before any other ACPI drivers
IPMI: Remove SMBus driver info from the docs
Matthew Garrett [Tue, 16 Oct 2012 20:53:38 +0000 (15:53 -0500)]
IPMI: Change link order
IPMI must be initialised before ACPI in order to ensure that any IPMI
services are available before ACPI driver initialisation attempts to use
any IPMI operation regions.
Corey Minyard [Tue, 16 Oct 2012 20:53:36 +0000 (15:53 -0500)]
IPMI: Remove SMBus driver info from the docs
Some documentation for the SMBus driver is in the IPMI docs, but that
code is not in the kernel tree at this point. So remove the docs to
avoid confusion.
David Rientjes [Wed, 17 Oct 2012 00:31:23 +0000 (17:31 -0700)]
mm, mempolicy: fix printing stack contents in numa_maps
When reading /proc/pid/numa_maps, it's possible to return the contents of
the stack where the mempolicy string should be printed if the policy gets
freed from beneath us.
This happens because mpol_to_str() may return an error the
stack-allocated buffer is then printed without ever being stored.
There are two possible error conditions in mpol_to_str():
- if the buffer allocated is insufficient for the string to be stored,
and
- if the mempolicy has an invalid mode.
The first error condition is not triggered in any of the callers to
mpol_to_str(): at least 50 bytes is always allocated on the stack and this
is sufficient for the string to be written. A future patch should convert
this into BUILD_BUG_ON() since we know the maximum strlen possible, but
that's not -rc material.
The second error condition is possible if a race occurs in dropping a
reference to a task's mempolicy causing it to be freed during the read().
The slab poison value is then used for the mode and mpol_to_str() returns
-EINVAL.
This race is only possible because get_vma_policy() believes that
mm->mmap_sem protects task->mempolicy, which isn't true. The exit path
does not hold mm->mmap_sem when dropping the reference or setting
task->mempolicy to NULL: it uses task_lock(task) instead.
Thus, it's required for the caller of a task mempolicy to hold
task_lock(task) while grabbing the mempolicy and reading it. Callers with
a vma policy store their mempolicy earlier and can simply increment the
reference count so it's guaranteed not to be freed.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Tue, 16 Oct 2012 20:05:25 +0000 (13:05 -0700)]
sparc64: Fix bit twiddling in sparc_pmu_enable_event().
There was a serious disconnect in the logic happening in
sparc_pmu_disable_event() vs. sparc_pmu_enable_event().
Event disable is implemented by programming a NOP event into the PCR.
However, event enable was not reversing this operation. Instead, it
was setting the User/Priv/Hypervisor trace enable bits.
That's not sparc_pmu_enable_event()'s job, that's what
sparc_pmu_enable() and sparc_pmu_disable() do .
The intent of sparc_pmu_enable_event() is clear, since it first clear
out the event type encoding field. So fix this by OR'ing in the event
encoding rather than the trace enable bits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 16 Oct 2012 07:37:27 +0000 (07:37 +0000)]
ipv6: addrconf: fix /proc/net/if_inet6
Commit 1d5783030a1 (ipv6/addrconf: speedup /proc/net/if_inet6 filling)
added bugs hiding some devices from if_inet6 and breaking applications.
"ip -6 addr" could still display all IPv6 addresses, while "ifconfig -a"
couldnt.
One way to reproduce the bug is by starting in a shell :
unshare -n /bin/bash
ifconfig lo up
And in original net namespace, lo device disappeared from if_inet6
Reported-by: Jan Hinnerk Stosch <janhinnerk.stosch@gmail.com> Tested-by: Jan Hinnerk Stosch <janhinnerk.stosch@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Mihai Maruseac <mihai.maruseac@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 15 Oct 2012 19:21:18 +0000 (19:21 +0000)]
qeth: fix deadlock between recovery and bonding driver
The recovery thread, when failing, tears down the respective interface. To do
so, it needs to obtain the rtnl lock first, as the interface configuration is
changed.
If another process tries to modify an interface setting at the same time, that
process can obtain the rtnl lock first, but the respective callback in the qeth
driver will block until recovery has completed - which cannot happen since the
calling process already obtained it.
In one particular case, the bonding driver acquired the rtnl lock to modify the
card's MAC address, while the recovery failed at the same time due to the card
being removed. Hence qeth_l2_set_mac_address (implicitly holding the rtnl lock)
was waiting on qeth_l2_recover, which deadlocked when waiting on the rtnl lock.
This patch uses rtnl_trylock instead of rtnl_lock in the recovery thread. If the
lock cannot be obtained, the interface will be left up, but the card state
remains in CARD_STATE_RECOVER, which will prevent any further activities on the
card.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
smsg_pm_restore_thaw() uses wrong checking before reconnecting
the IUCV path to *MSG. It is corrected with this patch.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zijie Pan <zijie.pan@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sun, 14 Oct 2012 04:30:56 +0000 (04:30 +0000)]
vlan: fix bond/team enslave of vlan challenged slave/port
In vlan_uses_dev() check for number of vlan devs rather than existence
of vlan_info. The reason is that vlan id 0 is there without appropriate
vlan dev on it by default which prevented from enslaving vlan challenged
dev.
Reported-by: Jon Stanley <jstanley@rmrf.net> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log