The alignment fixup incorrectly decodes faulting ARM VLDn/VSTn
instructions (where the optional alignment hint is given but incorrect)
as LDR/STR, leading to register corruption. Detect these and correctly
treat them as unhandled, so that userspace gets the fault it expects.
Reported-by: Simon Hosie <simon.hosie@arm.com> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPIDRURO and TPIDRURW registers need to be flushed during exec;
otherwise TLS information is potentially leaked. TPIDRURO in
particular needs careful treatment. Since flush_thread basically
needs the same code used to set the TLS in arm_syscall, pull that into
a common set_tls helper in tls.h and use it in both places.
Similarly, TEEHBR needs to be cleared during exec as well. Clearing
its save slot in thread_info isn't right as there is no guarantee
that a thread switch will occur before the new program runs. Just
setting the register directly is sufficient.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1dbfa187dad ("ARM: irq migration: force migration off CPU
going down") the ARM interrupt migration code on cpu offline calls
irqchip.irq_set_affinity() with the argument force=true. At the point
of this change the argument had no effect because it was not used by
any interrupt chip driver and there was no semantics defined.
This changed with commit 01f8fa4f01d8 ("genirq: Allow forcing cpu
affinity of interrupts") which made the force argument useful to route
interrupts to not yet online cpus without checking the target cpu
against the cpu online mask. The following commit ffde1de64012
("irqchip: gic: Support forced affinity setting") implemented this for
the GIC interrupt controller.
As a consequence the ARM cpu offline irq migration fails if CPU0 is
offlined, because CPU0 is still set in the affinity mask and the
validataion against cpu online mask is skipped to the force argument
being true. The following first_cpu(mask) selection always selects
CPU0 as the target.
Solve the issue by calling irq_set_affinity() with force=false from
the CPU offline irq migration code so the GIC driver validates the
affinity mask against CPU online mask and therefore removes CPU0 from
the possible target candidates.
Tested on TC2 hotpluging CPU0 in and out. Without this patch the system
locks up as the IRQs are not migrated away from CPU0.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
cut -d 'x' -f2|tr [a-z] [A-Z]`;
HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.
Fixes: 6e58b8f1daaf1af ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board") Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To deal with IPs which are specific to dra74x and dra72x, maintain seperate
ocp interface lists, while keeping the common list for all common IPs.
Move USB OTG SS4 to dra74x only list since its unavailable in
dra72x and is giving an abort during boot. The dra72x only list
is empty for now and a placeholder for future hwmod additions which
are specific to dra72x.
Fixes: d904b38df0db13 ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss") Reported-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Nishanth Menon <nm@ti.com>
[paul@pwsan.com: fixed comment style to conform with CodingStyle] Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors
upon entry to the kernel, but this is redundant:
- We clear the monitors on every exception return since commit 200b812d0084 ("Clear the exclusive monitor when returning from an
exception"), so this is not necessary to ensure the monitors are
cleared before returning from a fault handler.
- Any dummy STREX will target a temporary scratch area in memory, and
may succeed or fail without corrupting useful data. Its status value
will not be used.
- Any other STREX in the kernel must be preceded by an LDREX, which
will initialise the monitors consistently and will not depend on the
earlier state of the monitors.
Therefore we have no reason to care about the initial state of the
exclusive monitors when a data abort is taken, and clearing the monitors
prior to exception return (as we already do) is sufficient.
This patch removes the redundant clearing of the exclusive monitors from
the early abort handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 04f421e7 "spi: dw: use managed resources" changes drivers to use
managed functions, but seems wasn't properly tested in PCI case. The regs field
of struct dw_spi left uninitialized. Thus, kernel crashes when tries to access
to the SPI controller registers. This patch fixes the issue.
Fixes: 04f421e7 (spi: dw: use managed resources) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spi hangs waiting the completion of omap2_mcspi_rx_callback.
Signed-off-by: Jorge A. Ventura <jorge.araujo.ventura@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Drew reports another bug whereby the NFS client is now sending
an OPEN_DOWNGRADE in a situation where it should really have sent a
CLOSE: the client is opening the file for O_RDWR, but then trying to
do a downgrade to O_RDONLY, which is not allowed by the NFSv4 spec.
Reported-by: James Drews <drews@engr.wisc.edu> Link: http://lkml.kernel.org/r/541AD7E5.8020409@engr.wisc.edu Fixes: aee7af356e15 (NFSv4: Fix problems with close in the presence...) Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between nfs4_state_manager() and
nfs_server_remove_lists() that happens during a nfsv3 mount.
The v3 mount notices there is already a supper block so
nfs_server_remove_lists() called which uses the nfs_client_lock
spin lock to synchronize access to the client list.
At the same time nfs4_state_manager() is running through
the client list looking for work to do, using the same
lock. When nfs4_state_manager() wins the race to the
list, a v3 client pointer is found and not ignored
properly which causes the panic.
Moving some protocol checks before the state checking
avoids the panic.
The value64 parameter is an u64 point that used to transfer the value
for write to CMOS, or used to return the value that's read from CMOS.
The value64 is an u64 point, so don't need get address again. It causes
acpi_cmos_rtc_space_handler always return 0 to reader and didn't write
expected value to CMOS.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Joe Lawrence <joe.lawrence@stratus.com> Tested-by: Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.
On connecting the cable a message like this appears four times in the log:
reset full speed USB device number 4 using uhci_hcd
That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resuming from hibernate (S4) will restart and re-initialize xHC.
The device contexts are freed and will be re-allocated later during device reset.
Usb core will disable link pm in device resume before device reset, which will
try to change the max exit latency, accessing the device contexts before they are re-allocated.
There is no need to zero (disable) the max exit latency when disabling hw lpm
for a freshly re-initialized xHC. So check that device context exists before
doing anything. The max exit latency will be set again after device reset when usb core
enables the link pm.
Reported-by: Imre Deak <imre.deak@intel.com> Tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xhci initialization fails before the roothub bandwidth
domains (xhci->rh_bw[i]) are allocated it will oops when
trying to access rh_bw members in xhci_mem_cleanup().
Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.
That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.
This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.
This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.
This patch should be backported to all kernels containing
commit 71c731a.
Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware) Cc: Alexis R. Cortes <alexis.cortes@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the uwb_dev->bce entry is set before calling uwb_dev_add in
uwbd_dev_onair so that usermode will only see the device after it is
properly initialized. This fixes a kernel panic that can occur if
usermode tries to access the IEs sysfs attribute of a UWB device before
the driver has had a chance to set the beacon cache entry.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add back some PIDs that were mistakingly remove when reverting commit 73228a0538a7 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e3c ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize USB PHY after every Link controller reset
Cc: Tim Bird <tbird20d@gmail.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY drivers keep track of the current state of the hardware,
so don't change PHY settings under it.
Cc: Tim Bird <tbird20d@gmail.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 30a70b026b4cd ("usb: musb: fix obex in g_nokia.ko causing kernel
panic") attempted to fix runtime PM handling for PHYs that are on the
I2C bus. Commit 3063a12be2b0 ("usb: musb: fix PHY power on/off") then
changed things around to enable of PHYs that rely on runtime PM.
These changes however broke idling of the PHY and causes at least
100 mW extra power consumption on omaps, which is a lot with
the idle power consumption being below 10 mW range on many devices.
As calling phy_power_on/off from runtime PM calls in the USB
causes complicated issues with I2C connected PHYs, let's just let
the PHY do it's own runtime PM as needed. This leaves out the
dependency between PHYs and USB controller drivers for runtime
PM.
Let's fix the regression for twl4030-usb by adding minimal runtime
PM support. This allows idling the PHY on disconnect.
Note that we are changing to use standard runtime PM handling
for twl4030_phy_init() as that function just checks the state
and does not initialize the PHY. The PHY won't get initialized
until in twl4030_phy_power_on().
Fixes: 30a70b026b4cd ("usb: musb: fix obex in g_nokia.ko causing kernel panic") Fixes: 3063a12be2b0 ("usb: musb: fix PHY power on/off") Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 249751f22380 ("usb: phy: twl4030-usb: poll for ID disconnect")
added twl4030_id_workaround_work() to deal with lost interrupts
after ID pin goes down. Looks like commit f1ddc24c9e33 ("usb: phy:
twl4030-usb: remove *set_suspend* and *phy_init* ops") changed
things around for the generic phy framework, and delayed work no
longer got called except initially during boot.
The PHY connect and disconnect interrupts for twl4030-usb are not
working after disconnecting a USB-A cable from the board, and the
deeper idle states for omap are blocked as the USB controller
stays busy.
The issue can be solved by calling delayed work from twl4030_usb_irq()
when ID pin is down and the PHY is not asleep like we already do
in twl4030_id_workaround_work().
But as both twl4030_usb_irq() and twl4030_id_workaround_work()
already do pretty much the same thing, let's call twl4030_usb_irq()
from twl4030_id_workaround_work() instead of adding some more
duplicate code. We also must call sysfs_notify() only when we have
an interrupt and not from the delayed work as notified by
Grazvydas Ignotas <notasas@gmail.com>.
Fixes: f1ddc24c9e33 ("usb: phy: twl4030-usb: remove *set_suspend* and *phy_init* ops") Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.
Fixes the following warning from the sparse checker:
drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)
Sierra Wireless Direct IP devices using the 68A3 product ID
can be configured for modes including a CDC ECM class function.
The known example uses interface numbers 12 and 13 for the ECM
control and data interfaces respectively, consistent with CDC
MBIM function interface numbering on other Sierra devices.
It seems cleaner to restrict this driver to the ff/ff/ff
vendor specific interfaces rather than increasing the already
long interface number blacklist. This should be more future
proof if Sierra adds more class functions using interface
numbers not yet in the blacklist.
Remove dublicate Qualcom PID 0x3197 which is already handled by the
moto-modem driver since commit 6986a978eec7 ("USB: add new moto_modem
driver for some Morotola phones").
This reverts commit 73228a0538a7 ("USB: option,zte_ev: move most ZTE
CDMA devices to zte_ev").
Move the IDs of the devices that were previously driven by the option
driver back to that driver.
As several users have reported, the zte_ev driver is causing random
disconnects as well as reconnect failures.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Liu Lei, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Note that the zte_ev driver is based on code (once) distributed by ZTE
that still appears to originally have been reverse-engineered and bolted
onto the generic driver.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1), this is a first step in ultimately removing the redundant
zte_ev driver.
Note that AC2726 had already been moved back to option, and that some
IDs were in the device table of both drivers prior to the commit being
reverted.
Reported-by: Lei Liu <liu.lei78@zte.com.cn> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not log normal interrupt-urb shutdowns as errors.
The option driver has always been logging any nonzero interrupt-urb
status as an error, including when the urb is killed during normal
operation.
Commit 9096f1fbba91 ("USB: usb_wwan: fix potential NULL-deref at
resume") moved the interrupt urb submission from port probe and release
to open and close, thus potentially increasing the number of these
false-positive error messages dramatically.
Reported-by: Ed Butler <ressy66@ausics.net> Tested-by: Ed Butler <ressy66@ausics.net> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the number of ports requested by subdriver to avoid
writing beyond the end of fixed-size array in interface data.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of ports requested by a
subdriver (which could have been determined from device descriptors) did
not exceed this limit.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the maximum number of endpoints per type to avoid
writing beyond the end of a stack-allocated array.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of endpoints of a certain
type reported by a device did not exceed this limit.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove restoring a6 on some return paths and instead modify and restore
it in a single place, using symbolic name.
Correctly restore a7 from PT_AREG7 in case of illegal a6 value.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current definition of TLBTEMP_BASE_2 is always 32K above the
TLBTEMP_BASE_1, whereas fast_second_level_miss handler for the TLBTEMP
region analyzes virtual address bit (PAGE_SHIFT + DCACHE_ALIAS_ORDER)
to determine TLBTEMP region where the fault happened. The size of the
TLBTEMP region is also checked incorrectly: not 64K, but twice data
cache way size (whicht may as well be less than the instruction cache
way size).
Fix TLBTEMP_BASE_2 to be TLBTEMP_BASE_1 + data cache way size.
Provide TLBTEMP_SIZE that is a greater of doubled data cache way size or
the instruction cache way size, and use it to determine if the second
level TLB miss occured in the TLBTEMP region.
Practical occurence of page faults in the TLBTEMP area is extremely
rare, this code can be tested by deletion of all w[di]tlb instructions
in the tlbtemp_mapping region.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With SMP and a lot of debug options enabled task_struct::thread gets out
of reach of s32i/l32i instructions with base pointing at task_struct,
breaking build with the following messages:
arch/xtensa/kernel/entry.S: Assembler messages:
arch/xtensa/kernel/entry.S:1002: Error: operand 3 of 'l32i.n' has invalid value '1048'
arch/xtensa/kernel/entry.S:1831: Error: operand 3 of 's32i.n' has invalid value '1040'
arch/xtensa/kernel/entry.S:1832: Error: operand 3 of 's32i.n' has invalid value '1044'
Change base to point to task_struct::thread in such cases.
Don't use a10 in _switch_to to save/restore prev pointer as a2 is not
clobbered.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Virtual address is translated to the XCHAL_KSEG_CACHED region in the
dma_free_coherent, but is checked to be in the 0...XCHAL_KSEG_SIZE
range.
Change check for end of the range from 'addr >= X' to 'addr > X - 1' to
handle the case of X == 0.
Replace 'if (C) BUG();' construct with 'BUG_ON(C);'.
Signed-off-by: Alan Douglas <adouglas@cadence.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes userspace code that builds on other architectures but fails
on xtensa due to references to structures that other architectures don't
refer to. E.g. this fixes the following issue with python-2.7.8:
python-2.7.8/Modules/termios.c:861:25: error: invalid application
of 'sizeof' to incomplete type 'struct serial_multiport_struct'
{"TIOCSERGETMULTI", TIOCSERGETMULTI},
python-2.7.8/Modules/termios.c:870:25: error: invalid application
of 'sizeof' to incomplete type 'struct serial_multiport_struct'
{"TIOCSERSETMULTI", TIOCSERSETMULTI},
python-2.7.8/Modules/termios.c:900:24: error: invalid application
of 'sizeof' to incomplete type 'struct tty_struct'
{"TIOCTTYGSTRUCT", TIOCTTYGSTRUCT},
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise we may fail to init the second compute ring.
Noticed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise we may lose the DMA golden settings which can
lead to hangs, etc.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise we may lose the DMA golden settings which can
lead to hangs, etc.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems with special thermal configurations make sure we make
note of the thermal setup. This is required for proper firmware
configuration on these systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Semaphore values have 64 bits, not 32. This fixes a very subtle bug
that disables synchronization when the upper 32bits wasn't zero.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-By: Grigori Goronzy <greg@chown.ath.cx> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_suspend is handled in the radeon_suspend callbacks.
pm_resume has special handling depending on whether
dpm or legacy pm is enabled. Change radeon_gpu_reset
to mirror the behavior in the suspend and resume
pathes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code waiting for fifo idle was incorrect and could possibly spin
forever under certain circumstances.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reported-by: Mark Sheldon <markshel@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Reivewed-by: Mark Sheldon <markshel@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vblank waits in intel_tv_detect_type() are timing out for some
reason. This is a regression caused removing seemingly useless vblank
waits from the modeset seqeuence in:
drm/i915: Kill vblank waits after pipe enable on gmch platforms
So it turns out they weren't all entirely useless. Apparently the pipe
has to go through one full frame before we enable the TV port. Add a
vblank wait to intel_enable_tv() to make sure that happens.
Another approach was attempted by placing the vblank wait just after
enabling the port. The theory behind that attempt was that we need to
let the port stay enabled for one full frame before disabling it again
during load detection. But that didn't work, and we definitely must
have the vblank wait before enabling the port.
Cc: Alan Bartlett <ajb@elrepo.org> Tested-by: Alan Bartlett <ajb@elrepo.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79311 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've accidentally inverted the EIO/wedged handling in the fault
handler: We want to return the EIO as a SIGBUS only if it's not
because of the gpu having died, to prevent userspace from unduly
dying.
In my defence the comment right above is completely misleading, so fix
both.
v2: Drop the WARN_ON, it's not actually a bug to e.g. receive an -EIO
when swap-in fails.
v3: Don't remove too much ... oops.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first command will remove the PCI device from the kernel's device
list so the second command won't see it right away. But as it registers
a PCI driver it'll see it on the third command. If the system happens to
match one of the DMI table entries we'll try to call a function in long
released memory and generate an Oops, at best.
Fix this by removing the bogus annotation.
Modpost should have caught that one but it ignores section reference
mismatches from the .rodata section. :/
Fixes: 25e341cfc33d ("drm/i915: quirk away broken OpRegion VBT") Fixes: 8ca4013d702d ("CHROMIUM: i915: Add DMI override to skip CRT...") Fixes: 425d244c8670 ("drm/i915: ignore LVDS on intel graphics systems...") Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Duncan Laurie <dlaurie@chromium.org> Cc: Jarod Wilson <jarod@redhat.com> Cc: Rusty Russell <rusty@rustcorp.com.au> # Can modpost be fixed? Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The guard was introduced in commit ea1a8217b06b ("xattr: guard against
simultaneous glibc header inclusion") but it is using #ifdef to check
for a define that is either set to 1 or 0. Fix it to use #if instead.
* Without this patch:
$ { echo "#include <sys/xattr.h>"; echo "#include <linux/xattr.h>"; } | gcc -E -Iinclude/uapi - >/dev/null
include/uapi/linux/xattr.h:19:0: warning: "XATTR_CREATE" redefined [enabled by default]
#define XATTR_CREATE 0x1 /* set value, fail if attr already exists */
^
/usr/include/x86_64-linux-gnu/sys/xattr.h:32:0: note: this is the location of the previous definition
#define XATTR_CREATE XATTR_CREATE
^
Commit "HID: logitech: perform bounds checking on device_id early
enough" unfortunately leaks some errors to dmesg which are not real
ones:
- if the report is not a DJ one, then there is not point in checking
the device_id
- the receiver (index 0) can also receive some notifications which
can be safely ignored given the current implementation
Move out the test regarding the report_id and also discards
printing errors when the receiver got notified.
Fixes: ad3e14d7c5268c2e24477c6ef54bbdf88add5d36 Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The report passed to us from transport driver could potentially be
arbitrarily large, therefore we better sanity-check it so that
magicmouse_emit_touch() gets only valid values of raw_id.
The report passed to us from transport driver could potentially be
arbitrarily large, therefore we better sanity-check it so that raw_data
that we hold in picolcd_pending structure are always kept within proper
bounds.
cfq_group_service_tree_add() is applying new_weight at the beginning of
the function via cfq_update_group_weight().
This actually allows weight to change between adding it to and subtracting
it from children_weight, and triggers WARN_ON_ONCE() in
cfq_group_service_tree_del(), or even causes oops by divide error during
vfr calculation in cfq_group_service_tree_add().
The detailed scenario is as follows:
1. Create blkio cgroups X and Y as a child of X.
Set X's weight to 500 and perform some I/O to apply new_weight.
This X's I/O completes before starting Y's I/O.
2. Y starts I/O and cfq_group_service_tree_add() is called with Y.
3. cfq_group_service_tree_add() walks up the tree during children_weight
calculation and adds parent X's weight (500) to children_weight of root.
children_weight becomes 500.
4. Set X's weight to 1000.
5. X starts I/O and cfq_group_service_tree_add() is called with X.
6. cfq_group_service_tree_add() applies its new_weight (1000).
7. I/O of Y completes and cfq_group_service_tree_del() is called with Y.
8. I/O of X completes and cfq_group_service_tree_del() is called with X.
9. cfq_group_service_tree_del() subtracts X's weight (1000) from
children_weight of root. children_weight becomes -500.
This triggers WARN_ON_ONCE().
10. Set X's weight to 500.
11. X starts I/O and cfq_group_service_tree_add() is called with X.
12. cfq_group_service_tree_add() applies its new_weight (500) and adds it
to children_weight of root. children_weight becomes 0. Calcularion of
vfr triggers oops by divide error.
weight should be updated right before adding it to children_weight.
When a driver is set up without the jack detection explicitly (either
by passing a model option or via a specific fixup), the pin powermap
of IDT/STAC codecs is set up wrongly, resulting in the silence
output. It's because of a logic failure in stac_init_power_map().
It tries to avoid creating a callback for the pins that have other
auto-hp and auto-mic callbacks, but the check is done in a wrong way
at a wrong time. The stac_init_power_map() should be called after
creating other jack detection ctls, and the jack callback should be
created only for jack-detectable widgets.
This patch fixes the check in stac_init_power_map() and its callee
at the right place, after snd_hda_gen_build_controls().
ALC1150 codec seems to need the COEF- and PLL-setups just like its
compatible ALC882 codec. Some machines (e.g. SunMicro X10SAT) show
the problem like too low output volumes unless the COEF setup is
applied.
Acer Aspire 3830TG with CX20588 codec has a digital built-in mic that
has the same problem like many others, the inverted signal in stereo.
Apply the same fixup to this machine, too.
snd_info_get_line() documents that its last parameter must be one
less than the buffer size, but this API design guarantees that
(literally) every caller gets it wrong.
Just change this parameter to have its obvious meaning.
Reported-by: Tommi Rantala <tt.rantala@gmail.com> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I'm not sure what I was on when I wrote this, but when iterating over
the hardware watchpoint array (hbp_watch_array), our index is off by
ARM_MAX_BRP, so we walk off the end of our thread_struct...
... except, a dodgy condition in the loop means that it never executes
at all (bp cannot be NULL).
This patch fixes the code so that we remove the bp check and use the
correct index for accessing the watchpoint structures.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Epoll on trace_pipe can sometimes hang in a weird case. If the ring buffer is
empty when we set waiters_pending but an event shows up exactly at that moment
we can miss being woken up by the ring buffers irq work. Since
ring_buffer_empty() is inherently racey we will sometimes think that the buffer
is not empty. So we don't get woken up and we don't think there are any events
even though there were some ready when we added the watch, which makes us hang.
This patch fixes this by making sure that we are actually on the wait list
before we set waiters_pending, and add a memory barrier to make sure
ring_buffer_empty() is going to be correct.
In block write mode, when encapsulating dma_buffer, first element is
'command', the rest is data buffer, so only copy actual data buffer
starting from block[1] with the size indicating by block[0].
Signed-off-by: Fan Du <fan.du@intel.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition in at91_do_twi_xfer when signals arrive.
If a signal is recieved while waiting for a transfer to complete
wait_for_completion_interruptible_timeout() will return -ERESTARTSYS.
This is not handled correctly resulting in interrupts still being
enabled and a transfer being in flight when we return.
Symptoms include a range of oopses and bus lockups. Oopses can happen
when the transfer completes because the interrupt handler will corrupt
the stack. If a new transfer is started before the interrupt fires
the controller will start a new transfer in the middle of the old one,
resulting in confused slaves and a locked bus.
To avoid this, use wait_for_completion_io_timeout instead so that we
don't have to deal with gracefully shutting down the transfer and
disabling the interrupts.
Signed-off-by: Simon Lindgren <simon@aqwary.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was not bound checking the received length byte to ensure it was within the
the buffer size that is allocated for SMBus blocks. This resulted in buffer overflows
whenever an invalid length byte was received.
It also failed to ensure the length byte was not zero. If it received zero, it would end up
in an infinite loop as the at91_twi_read_next_byte function returned immediately without
allowing RHR to be read to clear the RXRDY interrupt.
Tested agaisnt a SMBus compliant battery.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "clock-frequency" DT property is listed as optional, However,
the current code stores the return value of of_property_read_u32 in
the return code of mv64xxx_of_config, but then forgets to clear it
after setting the default value of "clock-frequency". It is then
passed out to the main probe function, resulting in a probe failure
when "clock-frequency" is missing.
This patch checks and then throws away the return value of
of_property_read_u32, instead of storing it and having to clear it
afterwards.
This issue was discovered after the property was removed from all
sunxi DTs.
Fixes: 4c730a06c19bb ("i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The architecture specifies that when the processor wakes up from a WFE
or WFI instruction, the instruction is considered complete, however we
currrently return to EL1 (or EL0) at the WFI/WFE instruction itself.
While most guests may not be affected by this because their local
exception handler performs an exception returning setting the event bit
or with an interrupt pending, some guests like UEFI will get wedged due
this little mishap.
Simply skip the instruction when we have completed the emulation.
Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arm64 interrupt migration code on cpu offline calls
irqchip.irq_set_affinity() with the argument force=true. Originally
this argument had no effect because it was not used by any interrupt
chip driver and there was no semantics defined.
This changed with commit 01f8fa4f01d8 ("genirq: Allow forcing cpu
affinity of interrupts") which made the force argument useful to route
interrupts to not yet online cpus without checking the target cpu
against the cpu online mask. The following commit ffde1de64012
("irqchip: gic: Support forced affinity setting") implemented this for
the GIC interrupt controller.
As a consequence the cpu offline irq migration fails if CPU0 is
offlined, because CPU0 is still set in the affinity mask and the
validation against cpu online mask is skipped to the force argument
being true. The following first_cpu(mask) selection always selects
CPU0 as the target.
Commit 601c942176d8("arm64: use cpu_online_mask when using forced
irq_set_affinity") intended to fix the above mentioned issue but
introduced another issue where affinity can be migrated to a wrong
CPU due to unconditional copy of cpu_online_mask.
As with for arm, solve the issue by calling irq_set_affinity() with
force=false from the CPU offline irq migration code so the GIC driver
validates the affinity mask against CPU online mask and therefore
removes CPU0 from the possible target candidates. Also revert the
changes done in the commit 601c942176d8 as it's no longer needed.
Tested on Juno platform.
Fixes: 601c942176d8("arm64: use cpu_online_mask when using forced
irq_set_affinity") Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan reports that we leak TLS information from the parent context
during an exec, as we don't clear the TLS registers when flushing the
thread state.
This patch updates the flushing code so that we:
(1) Unconditionally zero the tpidr_el0 register (since this is fully
context switched for native tasks and zeroed for compat tasks)
(2) Zero the tp_value state in thread_info before clearing the
tpidrr0_el0 register for compat tasks (since this is only writable
by the set_tls compat syscall and therefore not fully switched).
A missing compiler barrier is also added to the compat set_tls syscall.
We ran into a case on ppc64 running mariadb where io_getevents would
return zeroed out I/O events. After adding instrumentation, it became
clear that there was some missing synchronization between reading the
tail pointer and the events themselves. This small patch fixes the
problem in testing.
Thanks to Zach for helping to look into this, and suggesting the fix.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Dan Aloni, commit f8567a3845ac ("aio: fix aio request
leak when events are reaped by userspace") introduces a regression when
user code attempts to perform io_submit() with more events than are
available in the ring buffer. Reverting that commit would reintroduce a
regression when user space event reaping is used.
Fixing this bug is a bit more involved than the previous attempts to fix
this regression. Since we do not have a single point at which we can
count events as being reaped by user space and io_getevents(), we have
to track event completion by looking at the number of events left in the
event ring. So long as there are as many events in the ring buffer as
there have been completion events generate, we cannot call
put_reqs_available(). The code to check for this is now placed in
refill_reqs_available().
A test program from Dan and modified by me for verifying this bug is available
at http://www.kvack.org/~bcrl/20140824-aio_bug.c .
Reported-by: Dan Aloni <dan@kernelim.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Acked-by: Dan Aloni <dan@kernelim.com> Cc: Kent Overstreet <kmo@daterainc.com> Cc: Mateusz Guzik <mguzik@redhat.com> Cc: Petr Matousek <pmatouse@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Crucial M550 may cause data corruption on queued trims and is
blacklisted. The pattern used for it fails to match 1TB one as the
capacity section will be four chars instead of three. Widen the
pattern.
In case the Device Tree blob passed by the boot agent supplies both an
'interrupts-extended' and an 'interrupts' property in order to allow for
older kernels to be usable, prefer the new-style 'interrupts-extended'
property which conveys a lot more information.
This allows us to have bootloaders willingly maintaining backwards
compatibility with older kernels without entirely deprecating the
'interrupts' property.
Update the bindings documentation to describe a situation where both the
'interrupts-extended' and the 'interrupts' property are present, and
which one takes precedence over the other.
Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bapm enabled the GPU and CPU to share TDP headroom. It was
disabled by default since some laptops hung when it was enabled
in conjunction with dpm. It seems to be stable on desktop
boards and fixes hangs on boot with dpm enabled on certain
boards, so enable it by default on desktop boards.
This is not a complete fix, but it is verified to make the ring
initialization failures during resume much less likely.
We were not able to root-cause this bug (likely HW-specific to Gen4 chips)
yet. This is therefore used as a ducttape before problem is fully
understood and proper fix created, so that people don't suffer from
completely unusable systems in the meantime.
Return 2 so we can be sure the kernel has the necessary
changes for acceleration to work.
Note: This patch depends on these two commits:
- drm/radeon: fix cut and paste issue for hawaii.
- drm/radeon: use packet2 for nop on hawaii with old firmware
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Andreas Boll <andreas.boll.dev@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seems to make VM flushes more stable on SI and CIK.
v2: only use the PFP on the GFX ring on CIK
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>