Ben Dooks [Tue, 1 Nov 2011 00:50:09 +0000 (00:50 +0000)]
Merge branches 'for-32/i2c/omap-v4', 'for-32/i2c/imx-dt', 'for-32/i2c/eg20t-v4', 'for-32/i2c/designware-v5' and 'for-32/i2c/au1550' into for-linus/i2c-3.2
Manuel Lauss [Sat, 22 Oct 2011 11:34:38 +0000 (13:34 +0200)]
i2c-au1550: increase timeout waiting for master done
Double the timeout in the loop which busy-waits for the "master-done"
bit to be set. This bit indicates whether an i2c transaction has
completed; on the DB1300 and DB1550 boards this timeout is slightly
too short and causes transactions to the WM8731 codec to be falsely flagged
as failed. The timeout itself is necessary since transactions to
non-existant slaves never set this bit in the first place (and cause
i2cdetect to hang).
With this change the WM8731 codec on the DB1300/DB1550 boards is correctly
detected and initialized.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Tomoya MORINAGA [Wed, 12 Oct 2011 04:13:06 +0000 (13:13 +0900)]
i2c-eg20t: Add initialize processing in case i2c-error occurs
In case disconnecting physical connection,
need to initialize i2c device for retry access.
This patch adds initialize process in case bus-idle fails and Lost arbitration.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Tomoya MORINAGA [Wed, 12 Oct 2011 04:13:03 +0000 (13:13 +0900)]
i2c-eg20t: Separate error processing
Error processing for NACK or wait-event must be precessed separately.
So divide wait-event error processing into NACK-receiving and timeout.
Add arbitration lost processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Dirk Brandewie [Thu, 6 Oct 2011 18:26:34 +0000 (11:26 -0700)]
i2c-designware: Push all register reads/writes into the core code.
Move all register manipulation code into the core, also move register
offset definitions to i2c-designware-core.c since the bus specific
portions of the driver no longer need/use them.
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Dirk Brandewie [Thu, 6 Oct 2011 18:26:33 +0000 (11:26 -0700)]
i2c-designware: Support multiple cores using same ISR
Add check to make sure that the core is enabled and has outstanding
interrupts. The activity bit is masked due to the fact that it will
stay active even after the controller has been disabled until the
contoller internal state machines have settled.
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Dirk Brandewie [Thu, 6 Oct 2011 18:26:32 +0000 (11:26 -0700)]
i2c-designware: move controller config to bus specific portion of driver
With multiple I2C adapters possible in the system each running at
(possibly) different speeds we need to move the controller
configuration bit field to the adapter.
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Dirk Brandewie [Thu, 6 Oct 2011 18:26:30 +0000 (11:26 -0700)]
i2c-designware: Move retriveving the clock speed out of core code.
The clock frequecy supplied to the IP core is specific to a single
instance of the driver. This patch makes it possible to have multiple
Designware I2C cores in the system possibly running at different core
frequencies.
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Allows CPUs of a given endianness to access a dw controller of a different
endianness. Endianncess difference is detected at run time through the dw
component type register.
Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Barry Song <21cnbao@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Kevin Hilman [Tue, 17 May 2011 14:31:38 +0000 (16:31 +0200)]
I2C: OMAP: remove dev->idle, use usage counting provided by runtime PM
Current usage of runtime PM is not quite correct. The actual
idle/unidle of the I2C hardware should not happen until the runtime PM
callbacks are called. Therefore, change omap_i2c_[un]idle() functions
to only be called from the runtime PM callbacks (when usage count
transitions to/from zero.)
Also, the runtime PM core does usage counting and replaces
functionality currently managed by the dev->idle flag. Remove usage
of dev->idle in favor of using runtime PM, and checking status using
pm_runtime_suspended().
Kevin Hilman [Tue, 17 May 2011 14:31:37 +0000 (16:31 +0200)]
I2C: OMAP: remove unneccesary use of pdev
A pointer to the struct device associated with the i2c device is
already kept in the struct omap_i2c_dev, so use omap_i2c_device to
find the pointer to struct device.
Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:10 +0000 (07:43 -0700)]
I2C: OMAP1/OMAP2+: prepend I2C IP version to probed version shown in dev_info
The IP version is prepended to the existing printed probed
version as an "epoch" version.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:09 +0000 (07:43 -0700)]
I2C: OMAP2+: Convert omap I2C driver to use feature implementation flags from platform data
This patch eliminates all cpu_...() tests from the OMAP I2C driver.
Instead, it uses the functionality flags in the platform data to make
the decisions about product variations the driver needs to handle.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:09 +0000 (07:43 -0700)]
I2C: OMAP1: set i2c unit feature implementation flags in platform data
Most of the OMAP1 implementation flags are set statically, with the
exception that omap7xx has its data bus wired up differently.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:08 +0000 (07:43 -0700)]
I2C: OMAP2+: Pass flags up to omap i2c platform_data as well
This is how the driver can find the flags for its implementation
functionality in its platform_data
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:08 +0000 (07:43 -0700)]
I2C: OMAP1/OMAP2+: add flags field to omap i2c platform data
OMAP I2C driver can access the configuration flags through
its platform data.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:07 +0000 (07:43 -0700)]
I2C: OMAP2+: address confused probed version naming
The driver reflects the confusion that probed I2C revision
from the hardware of 0x40 means it is on an OMAP4430.
However, you will probe the same 0x40 ID on an OMAP3530. So
this patch changes the name to reflect that.
It also clarifies that the original name OMAP_I2C_REV_2 is
referring to some ancient OMAP1 revision number, not to be
confused with the IP revisions this patch series introduces.
Similarly the term "rev" is used in the ancient OMAP1 ISR,
the term is changed to use omap1 instead.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:07 +0000 (07:43 -0700)]
I2C: OMAP2+: Solve array bounds overflow error on i2c idle
This solves the main problem the patch series is about. Prior
to this patch on OMAP3530 the driver wrongly interprets the I2C
peripheral unit's own reported revision as meaning it is running
on an IP V2 device and must use the extended registers.
In fact OMAP3530 is IP V1 with the smaller register set, the
reason for the confusion is that the hardware does in fact report
having the same IP revision index as is found on an OMAP4430,
which really is IP V2 and has the extended registers.
This corrects the test for which registers to use so that it
decides using hwmod knowledge found in the platform_data.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:06 +0000 (07:43 -0700)]
I2C: OMAP2+: use platform_data ip revision to select register map
Change the register map names to reflect the IP revision they
are representing, and use the platform_data IP revision index
to select between them at init time.
Eliminates 1 of 17 cpu_...() calls in the driver.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:06 +0000 (07:43 -0700)]
I2C: OMAP2+: Pass hwmod rev knowledge via platform_data when i2c bus added
Mark each OMAP I2C bus with the hwmod's knowledge of which I2C
IP version is in the chip we're running on.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:06 +0000 (07:43 -0700)]
I2C: OMAP1: set IP revision in platform data
All OMAP1 are using "IP revision 1" in terms of register
layout. We set this information in omap1_i2c_add_bus() so
we don't have to use cpu_is_xxx() any more in the omap i2c
driver.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:05 +0000 (07:43 -0700)]
I2C: OMAP: add rev to omap i2c platform data
We need to pass the I2C IP revision from the hwmod class up
into the OMAP I2C driver, which does not have direct
access to it.
This adds a member to the platform data the OMAP I2C driver
does use already to hold the I2C IP revision.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Andy Green [Mon, 30 May 2011 14:43:04 +0000 (07:43 -0700)]
I2C: OMAP2+: Name registers in I2C IP V2 only accordingly
The OMAP I2C driver dynamically chooses between two register sets of
differing sizes depending on the cpu type it finds itself on.
It has been observed that the existing code references non-existing
registers on OMAP3530, because while it correctly chose the smaller
register layout based on cpu type, the code uses the probed register
ID to decide if to execute code referencing an extra register, and
both register layout devices on OMAP3530 and OMAP4430 report the same
probed ID of 0x40.
This patch changes the extended register names only found on IP V2
of the I2C peripheral unit accordingly to help show up errors in usage.
Cc: patches@linaro.org Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kevin Hilman <khilman@ti.com>
Linus Torvalds [Fri, 28 Oct 2011 19:02:27 +0000 (12:02 -0700)]
Merge branch 'devel-stable' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'devel-stable' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (178 commits)
ARM: 7139/1: fix compilation with CONFIG_ARM_ATAG_DTB_COMPAT and large TEXT_OFFSET
ARM: gic, local timers: use the request_percpu_irq() interface
ARM: gic: consolidate PPI handling
ARM: switch from NO_MACH_MEMORY_H to NEED_MACH_MEMORY_H
ARM: mach-s5p64x0: remove mach/memory.h
ARM: mach-s3c64xx: remove mach/memory.h
ARM: plat-mxc: remove mach/memory.h
ARM: mach-prima2: remove mach/memory.h
ARM: mach-zynq: remove mach/memory.h
ARM: mach-bcmring: remove mach/memory.h
ARM: mach-davinci: remove mach/memory.h
ARM: mach-pxa: remove mach/memory.h
ARM: mach-ixp4xx: remove mach/memory.h
ARM: mach-h720x: remove mach/memory.h
ARM: mach-vt8500: remove mach/memory.h
ARM: mach-s5pc100: remove mach/memory.h
ARM: mach-tegra: remove mach/memory.h
ARM: plat-tcc: remove mach/memory.h
ARM: mach-mmp: remove mach/memory.h
ARM: mach-cns3xxx: remove mach/memory.h
...
Fix up mostly pretty trivial conflicts in:
- arch/arm/Kconfig
- arch/arm/include/asm/localtimer.h
- arch/arm/kernel/Makefile
- arch/arm/mach-shmobile/board-ap4evb.c
- arch/arm/mach-u300/core.c
- arch/arm/mm/dma-mapping.c
- arch/arm/mm/proc-v7.S
- arch/arm/plat-omap/Kconfig
largely due to some CONFIG option renaming (ie CONFIG_PM_SLEEP ->
CONFIG_ARM_CPU_SUSPEND for the arm-specific suspend code etc) and
addition of NEED_MACH_MEMORY_H next to HAVE_IDE.
Linus Torvalds [Fri, 28 Oct 2011 17:49:34 +0000 (10:49 -0700)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue: (21 commits)
leases: fix write-open/read-lease race
nfs: drop unnecessary locking in llseek
ext4: replace cut'n'pasted llseek code with generic_file_llseek_size
vfs: add generic_file_llseek_size
vfs: do (nearly) lockless generic_file_llseek
direct-io: merge direct_io_walker into __blockdev_direct_IO
direct-io: inline the complete submission path
direct-io: separate map_bh from dio
direct-io: use a slab cache for struct dio
direct-io: rearrange fields in dio/dio_submit to avoid holes
direct-io: fix a wrong comment
direct-io: separate fields only used in the submission path from struct dio
vfs: fix spinning prevention in prune_icache_sb
vfs: add a comment to inode_permission()
vfs: pass all mask flags check_acl and posix_acl_permission
vfs: add hex format for MAY_* flag values
vfs: indicate that the permission functions take all the MAY_* flags
compat: sync compat_stats with statfs.
vfs: add "device" tag to /proc/self/mountstats
cleanup: vfs: small comment fix for block_invalidatepage
...
Fix up trivial conflict in fs/gfs2/file.c (llseek changes)
Linus Torvalds [Fri, 28 Oct 2011 17:44:50 +0000 (10:44 -0700)]
Merge http://sucs.org/~rohan/git/gfs2-3.0-nmw
* http://sucs.org/~rohan/git/gfs2-3.0-nmw: (24 commits)
GFS2: Move readahead of metadata during deallocation into its own function
GFS2: Remove two unused variables
GFS2: Misc fixes
GFS2: rewrite fallocate code to write blocks directly
GFS2: speed up delete/unlink performance for large files
GFS2: Fix off-by-one in gfs2_blk2rgrpd
GFS2: Clean up ->page_mkwrite
GFS2: Correctly set goal block after allocation
GFS2: Fix AIL flush issue during fsync
GFS2: Use cached rgrp in gfs2_rlist_add()
GFS2: Call do_strip() directly from recursive_scan()
GFS2: Remove obsolete assert
GFS2: Cache the most recently used resource group in the inode
GFS2: Make resource groups "append only" during life of fs
GFS2: Use rbtree for resource groups and clean up bitmap buffer ref count scheme
GFS2: Fix lseek after SEEK_DATA, SEEK_HOLE have been added
GFS2: Clean up gfs2_create
GFS2: Use ->dirty_inode()
GFS2: Fix bug trap and journaled data fsync
GFS2: Fix inode allocation error path
...
Linus Torvalds [Fri, 28 Oct 2011 17:43:32 +0000 (10:43 -0700)]
Merge branch '3.2-without-smb2' of git://git.samba.org/sfrench/cifs-2.6
* '3.2-without-smb2' of git://git.samba.org/sfrench/cifs-2.6: (52 commits)
Fix build break when freezer not configured
Add definition for share encryption
CIFS: Make cifs_push_locks send as many locks at once as possible
CIFS: Send as many mandatory unlock ranges at once as possible
CIFS: Implement caching mechanism for posix brlocks
CIFS: Implement caching mechanism for mandatory brlocks
CIFS: Fix DFS handling in cifs_get_file_info
CIFS: Fix error handling in cifs_readv_complete
[CIFS] Fixup trivial checkpatch warning
[CIFS] Show nostrictsync and noperm mount options in /proc/mounts
cifs, freezer: add wait_event_freezekillable and have cifs use it
cifs: allow cifs_max_pending to be readable under /sys/module/cifs/parameters
cifs: tune bdi.ra_pages in accordance with the rsize
cifs: allow for larger rsize= options and change defaults
cifs: convert cifs_readpages to use async reads
cifs: add cifs_async_readv
cifs: fix protocol definition for READ_RSP
cifs: add a callback function to receive the rest of the frame
cifs: break out 3rd receive phase into separate function
cifs: find mid earlier in receive codepath
...
Linus Torvalds [Fri, 28 Oct 2011 17:31:42 +0000 (10:31 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (69 commits)
xfs: add AIL pushing tracepoints
xfs: put in missed fix for merge problem
xfs: do not flush data workqueues in xfs_flush_buftarg
xfs: remove XFS_bflush
xfs: remove xfs_buf_target_name
xfs: use xfs_ioerror_alert in xfs_buf_iodone_callbacks
xfs: clean up xfs_ioerror_alert
xfs: clean up buffer allocation
xfs: remove buffers from the delwri list in xfs_buf_stale
xfs: remove XFS_BUF_STALE and XFS_BUF_SUPER_STALE
xfs: remove XFS_BUF_SET_VTYPE and XFS_BUF_SET_VTYPE_REF
xfs: remove XFS_BUF_FINISH_IOWAIT
xfs: remove xfs_get_buftarg_list
xfs: fix buffer flushing during unmount
xfs: optimize fsync on directories
xfs: reduce the number of log forces from tail pushing
xfs: Don't allocate new buffers on every call to _xfs_buf_find
xfs: simplify xfs_trans_ijoin* again
xfs: unlock the inode before log force in xfs_change_file_space
xfs: unlock the inode before log force in xfs_fs_nfs_commit_metadata
...
Add a generic_file_llseek variant to the VFS that allows passing in
the maximum file size of the file system, instead of always
using maxbytes from the superblock.
This can be used to eliminate some cut'n'paste seek code in ext4.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
The i_mutex lock use of generic _file_llseek hurts. Independent processes
accessing the same file synchronize over a single lock, even though
they have no need for synchronization at all.
Under high utilization this can cause llseek to scale very poorly on larger
systems.
This patch does some rethinking of the llseek locking model:
First the 64bit f_pos is not necessarily atomic without locks
on 32bit systems. This can already cause races with read() today.
This was discussed on linux-kernel in the past and deemed acceptable.
The patch does not change that.
Let's look at the different seek variants:
SEEK_SET: Doesn't really need any locking.
If there's a race one writer wins, the other loses.
For 32bit the non atomic update races against read()
stay the same. Without a lock they can also happen
against write() now. The read() race was deemed
acceptable in past discussions, and I think if it's
ok for read it's ok for write too.
=> Don't need a lock.
SEEK_END: This behaves like SEEK_SET plus it reads
the maximum size too. Reading the maximum size would have the
32bit atomic problem. But luckily we already have a way to read
the maximum size without locking (i_size_read), so we
can just use that instead.
Without i_mutex there is no synchronization with write() anymore,
however since the write() update is atomic on 64bit it just behaves
like another racy SEEK_SET. On non atomic 32bit it's the same
as SEEK_SET.
=> Don't need a lock, but need to use i_size_read()
SEEK_CUR: This has a read-modify-write race window
on the same file. One could argue that any application
doing unsynchronized seeks on the same file is already broken.
But for the sake of not adding a regression here I'm
using the file->f_lock to synchronize this. Using this
lock is much better than the inode mutex because it doesn't
synchronize between processes.
=> So still need a lock, but can use a f_lock.
This patch implements this new scheme in generic_file_llseek.
I dropped generic_file_llseek_unlocked and changed all callers.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Andi Kleen [Tue, 2 Aug 2011 04:38:08 +0000 (21:38 -0700)]
direct-io: inline the complete submission path
Add inlines to all the submission path functions. While this increases
code size it also gives gcc a lot of optimization opportunities
in this critical hotpath.
In particular -- together with some other changes -- this
allows gcc to get rid of the unnecessary clearing of
sdio at the beginning and optimize the messy parameter passing.
Any non inlining of a function which takes a sdio parameter
would break this optimization because they cannot be done if the
address of a structure is taken.
Note that benefits are only seen with CONFIG_OPTIMIZE_INLINING
and CONFIG_CC_OPTIMIZE_FOR_SIZE both set to off.
This gives about 2.2% improvement on a large database benchmark
with a high IOPS rate.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Andi Kleen [Tue, 2 Aug 2011 04:38:07 +0000 (21:38 -0700)]
direct-io: separate map_bh from dio
Only a single b_private field in the map_bh buffer head is needed after
the submission path. Move map_bh separately to avoid storing
this information in the long term slab.
This avoids the weird 104 byte hole in struct dio_submit which also needed
to be memseted early.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Andi Kleen [Tue, 2 Aug 2011 04:38:03 +0000 (21:38 -0700)]
direct-io: separate fields only used in the submission path from struct dio
This large, but largely mechanic, patch moves all fields in struct dio
that are only used in the submission path into a separate on stack
data structure. This has the advantage that the memory is very likely
cache hot, which is not guaranteed for memory fresh out of kmalloc.
This also gives gcc more optimization potential because it can easier
determine that there are no external aliases for these variables.
The sdio initialization is a initialization now instead of memset.
This allows gcc to break sdio into individual fields and optimize
away unnecessary zeroing (after all the functions are inlined)
Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
We need to move the inode to the end of the list to actually make the
spinning prevention explained in the comment above it work. With a
plain list_move it will simply stay in place as we're always reclaiming
from the head of the list.
Acked-by: J. Bruce Fields <bfields@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andreas Gruenbacher <agruen@kernel.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
vfs: pass all mask flags check_acl and posix_acl_permission
Acked-by: J. Bruce Fields <bfields@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andreas Gruenbacher <agruen@kernel.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
We are going to add more flags and having them in hex format
make it simpler
Acked-by: J. Bruce Fields <bfields@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
vfs: indicate that the permission functions take all the MAY_* flags
Acked-by: J. Bruce Fields <bfields@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andreas Gruenbacher <agruen@kernel.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
This was found by inspection while tracking a similar
bug in compat_statfs64, that has been fixed in mainline
since decemeber.
- This fixes a bug where not all of the f_spare fields
were cleared on mips and s390.
- Add the f_flags field to struct compat_statfs
- Copy f_flags to userspace in case someone cares.
- Use __clear_user to copy the f_spare field to userspace
to ensure that all of the elements of f_spare are cleared.
On some architectures f_spare is has 5 ints and on some
architectures f_spare only has 4 ints. Which makes
the previous technique of clearing each int individually
broken.
I don't expect anyone actually uses the old statfs system
call anymore but if they do let them benefit from having
the compat and the native version working the same.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Linus Torvalds [Fri, 28 Oct 2011 12:54:23 +0000 (05:54 -0700)]
Merge branch 'drm-core-next' of git://people.freedesktop.org/~airlied/linux
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (290 commits)
Revert "drm/ttm: add a way to bo_wait for either the last read or last write"
Revert "drm/radeon/kms: add a new gem_wait ioctl with read/write flags"
vmwgfx: Don't pass unused arguments to do_dirty functions
vmwgfx: Emulate depth 32 framebuffers
drm/radeon: Lower the severity of the radeon lockup messages.
drm/i915/dp: Fix eDP on PCH DP on CPT/PPT
drm/i915/dp: Introduce is_cpu_edp()
drm/i915: use correct SPD type value
drm/i915: fix ILK+ infoframe support
drm/i915: add DP test request handling
drm/i915: read full receiver capability field during DP hot plug
drm/i915/dp: Remove eDP special cases from bandwidth checks
drm/i915/dp: Fix the math in intel_dp_link_required
drm/i915/panel: Always record the backlight level again (but cleverly)
i915: Move i915_read/write out of line
drm/i915: remove transcoder PLL mashing from mode_set per specs
drm/i915: if transcoder disable fails, say which
drm/i915: set watermarks for third pipe on IVB
drm/i915: export a CPT mode set verification function
drm/i915: fix transcoder PLL select masking
...
Linus Torvalds [Fri, 28 Oct 2011 12:46:02 +0000 (05:46 -0700)]
Merge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, doc: Remove int 0xcc from entry_64.S documentation
x86, vsyscall: Add missing <asm/fixmap.h> to arch/x86/mm/fault.c
Fix up trivial conflicts in arch/x86/mm/fault.c (asm/fixmap.h vs
asm/vsyscall.h: both work, which to use? Whatever..)
Linus Torvalds [Fri, 28 Oct 2011 12:43:29 +0000 (05:43 -0700)]
Merge branch 'x86-spinlocks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-spinlocks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, ticketlock: remove obsolete comment
x86, cmpxchg: Use __compiletime_error() to make usage messages a bit nicer
x86, ticketlock: Make __ticket_spin_trylock common
x86, ticketlock: Convert __ticket_spin_lock to use xadd()
x86, ticketlock: Convert spin loop to C
x86, ticketlock: Clean up types and accessors
x86: Use xadd helper more widely
x86: Add xadd helper macro
x86, cmpxchg: Unify cmpxchg into cmpxchg.h
x86, cmpxchg: Move 64-bit set64_bit() to match 32-bit
x86, cmpxchg: Move 32-bit __cmpxchg_wrong_size to match 64 bit.
x86, cmpxchg: <linux/alternative.h> has LOCK_PREFIX
Linus Torvalds [Fri, 28 Oct 2011 12:29:07 +0000 (05:29 -0700)]
Merge branch 'x86-rdrand-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-rdrand-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, random: Verify RDRAND functionality and allow it to be disabled
x86, random: Architectural inlines to get random integers with RDRAND
random: Add support for architectural random hooks
Fix up trivial conflicts in drivers/char/random.c: the architectural
random hooks touched "get_random_int()" that was simplified to use MD5
and not do the keyptr thing any more (see commit 6e5714eaf77d: "net:
Compute protocol sequence numbers and fragment IDs using MD5").
Linus Torvalds [Fri, 28 Oct 2011 12:14:48 +0000 (05:14 -0700)]
Merge branch 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Add microcode revision to /proc/cpuinfo
x86, microcode: Correct microcode revision format
coretemp: Get microcode revision from cpu_data
x86, intel: Use c->microcode for Atom errata check
x86, intel: Output microcode revision in /proc/cpuinfo
x86, microcode: Don't request microcode from userspace unnecessarily
Fix up trivial conflicts in arch/x86/kernel/cpu/amd.c (conflict between
moving AMD BSP code to cpu_dev helper function and adding AMD microcode
revision to /proc/cpuinfo code)
Linus Torvalds [Fri, 28 Oct 2011 12:03:12 +0000 (05:03 -0700)]
Merge branch 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, amd: Include linux/elf.h since we use stuff from asm/elf.h
x86: cache_info: Update calculation of AMD L3 cache indices
x86: cache_info: Kill the atomic allocation in amd_init_l3_cache()
x86: cache_info: Kill the moronic shadow struct
x86: cache_info: Remove bogus free of amd_l3_cache data
x86, amd: Include elf.h explicitly, prepare the code for the module.h split
x86-32, amd: Move va_align definition to unbreak 32-bit build
x86, amd: Move BSP code to cpu_dev helper
x86: Add a BSP cpu_dev helper
x86, amd: Avoid cache aliasing penalties on AMD family 15h
Bryan Schumaker [Fri, 7 Oct 2011 17:41:15 +0000 (13:41 -0400)]
vfs: add "device" tag to /proc/self/mountstats
nfsiostat was failing to find mounted filesystems on kernels after
2.6.38 because of changes to show_vfsstat() by commit c7f404b40a3665d9f4e9a927cc5c1ee0479ed8f9. This patch adds back the
"device" tag before the nfs server entry so scripts can parse the
mountstats file correctly.
Jeff Layton [Thu, 27 Oct 2011 21:53:08 +0000 (23:53 +0200)]
vfs: iov_iter: have iov_iter_advance decrement nr_segs appropriately
Currently, when you call iov_iter_advance, then the pointer to the iovec
array can be incremented, but it does not decrement the nr_segs value in
the iov_iter struct. The result is a iov_iter struct with a nr_segs
value that goes beyond the end of the array.
While I'm not aware of anything that's specifically broken by this, it
seems odd and a bit dangerous not to decrement that value. If someone
were to trust the nr_segs value to be correct, then they could end up
walking off the end of the array.
Changing this might also provide some micro-optimization when dealing
with the last iovec in an array. Many of the other routines that deal
with iov_iter have optimized codepaths when nr_segs == 1.
Cc: Nick Piggin <npiggin@suse.de> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Steve French [Tue, 25 Oct 2011 01:46:50 +0000 (20:46 -0500)]
Add definition for share encryption
Samba supports a setfs info level to negotiate encrypted
shares. This patch adds the defines so we recognize
this info level. Later patches will add the enablement
for it.
Acked-by: Jeremy Allison <jra@samba.org> Signed-off-by: Steve French <smfrench@gmail.com>
Linus Torvalds [Thu, 27 Oct 2011 06:44:20 +0000 (08:44 +0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (68 commits)
Input: adp5589-keys - add support for the ADP5585 derivatives
Input: imx_keypad - add pm suspend and resume support
Input: force feedback - potential integer wrap in input_ff_create()
Input: tsc2007 - make sure that X plate resistance is specified
Input: serio_raw - fix memory leak when closing char device
Input: serio_raw - kick clients when disconnecting port
Input: serio_raw - explicitly mark disconnected ports as dead
Input: serio_raw - fix coding style issues
Input: serio_raw - use dev_*() for messages
Input: serio_raw - use bool for boolean data
Input: serio_raw - perform proper locking when adding clients to list
Input: serio_raw - rename serio_raw_list to serio_raw_client
Input: serio_raw - use kref instead of rolling out its own refcounting
Input: psmouse - switch to using dev_*() for messages
Input: wacom - correct max Y value on medium bamboos
Input: wacom - add ABS_DISTANCE to Bamboo Pen reports
Input: wacom - remove unneeded touch pressure initialization
Input: lm8323 - wrap suspend and resume in CONFIG_PM_SLEEP
Input: ad7879-i2c - wrap suspend and resume in CONFIG_PM_SLEEP
Input: synaptics_i2c - wrap suspend and resume in CONFIG_PM_SLEEP
...
Linus Torvalds [Thu, 27 Oct 2011 06:41:50 +0000 (08:41 +0200)]
Merge branch 'clk' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'clk' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7131/1: clkdev: Add Common Macro for clk_lookup
clk: spi-pl022: convert to clk_prepare()/clk_unprepare()
clk: timer-sp: convert to clk_prepare()/clk_unprepare()
clk: sa1111: convert to clk_prepare()/clk_unprepare()
clk: mmci: convert to clk_prepare()/clk_unprepare()
clk: amba-pl011: convert to clk_prepare()/clk_unprepare()
clk: amba-pl010: convert to clk_prepare()/clk_unprepare()
clk: amba-clcd: convert to clk_prepare()/clk_unprepare()
clk: amba bus: convert to clk_prepare()/clk_unprepare()
clk: provide prepare/unprepare functions
Linus Torvalds [Thu, 27 Oct 2011 06:40:50 +0000 (08:40 +0200)]
Merge branch 'amba' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'amba' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7079/1: spi: Fix builderror in spi-pl022.c
PM: add runtime PM support to MMCI
PM: add runtime PM support to core Primecell driver
Linus Torvalds [Thu, 27 Oct 2011 06:32:37 +0000 (08:32 +0200)]
Merge branch 'upstream-linus' of git://github.com/jgarzik/libata-dev
* 'upstream-linus' of git://github.com/jgarzik/libata-dev: (50 commits)
pata_efar: fix register naming used in efar_set_piomode()
pata_rdc: add Power Management support
ata_piix: unify code for programming PIO and MWDMA timings
ata_piix: SITRE handling fix
libata: make ata_sff_data_xfer_noirq() work with 32-bit PIO
pata_artop: add Power Management support
pata_sl82c105: add Power Management support
pata_pdc2027x: add Power Management support
pata_legacy: use PIO mask defines
pata_legacy: unify QDI ->set_piomode methods
libata: remove no longer needed pata_qdi driver
pata_it8213: fix register naming used in it8213_set_piomode()
pata_it8213: add UDMA100 and UDMA133 support
pata_rdc: parallel scanning needs an extra locking
pata_via: add via_fixup()
libata: ata_timing_compute() fixup
pata_scc: add proper cable detection method
pata_arasan_cf: remove bogus to_platform_device() calls
pata_atiixp: add proper ->prereset method
pata_serverworks: add serverworks_fixup()
...
Linus Torvalds [Wed, 26 Oct 2011 19:46:18 +0000 (21:46 +0200)]
Merge branch 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
tools, slub: Fix off-by-one buffer corruption after readlink() call
slub: Discard slab page when node partial > minimum partial number
slub: correct comments error for per cpu partial
mm: restrict access to slab files under procfs and sysfs
slub: Code optimization in get_partial_node()
slub: doc: update the slabinfo.c file path
slub: explicitly document position of inserting slab to partial list
slub: update slabinfo tools to report per cpu partial list statistics
slub: per cpu cache for partial pages
slub: return object pointer from get_partial() / new_slab().
slub: pass kmem_cache_cpu pointer to get_partial()
slub: Prepare inuse field in new_slab()
slub: Remove useless statements in __slab_alloc
slub: free slabs without holding locks
slub: use print_hex_dump
slab: use print_hex_dump
Linus Torvalds [Wed, 26 Oct 2011 19:33:50 +0000 (21:33 +0200)]
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
* 'for-linus' of git://git.open-osd.org/linux-open-osd: (21 commits)
ore: Enable RAID5 mounts
exofs: Support for RAID5 read-4-write interface.
ore: RAID5 Write
ore: RAID5 read
fs/Makefile: Always inspect exofs/
ore: Make ore_calc_stripe_info EXPORT_SYMBOL
ore/exofs: Change ore_check_io API
ore/exofs: Define new ore_verify_layout
ore: Support for partial component table
ore: Support for short read/writes
exofs: Support for short read/writes
ore: Remove check for ios->kern_buff in _prepare_for_striping to later
ore: cleanup: Embed an ore_striping_info inside ore_io_state
ore: Only IO one group at a time (API change)
ore/exofs: Change the type of the devices array (API change)
ore: Make ore_striping_info and ore_calc_stripe_info public
exofs: Remove unused data_map member from exofs_sb_info
exofs: Rename struct ore_components comps => oc
exofs/super.c: local functions should be static
exofs/ore.c: local functions should be static
...
Linus Torvalds [Wed, 26 Oct 2011 15:43:08 +0000 (17:43 +0200)]
Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, unistd: Remove bogus __IGNORE_getcpu
x86, mm, trivial: Remove unnecessary get_order() in free_thread_info()
x86, cleanup: Remove unneeded version.h include from arch/x86/
Linus Torvalds [Wed, 26 Oct 2011 15:42:03 +0000 (17:42 +0200)]
Merge branch 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64: Fix CFI data for interrupt frames
x86-64: Don't apply destructive erratum workaround on unaffected CPUs
Linus Torvalds [Wed, 26 Oct 2011 15:30:33 +0000 (17:30 +0200)]
Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Standardize on CONFIG_SPARSE_IRQ=y
x86, ioapic: Clean up ioapic/apic_id usage
x86, ioapic: Factor out print_IO_APIC() to only print one io apic
x86, ioapic: Print out irte with right ioapic index
x86, ioapic: Split up setup_ioapic_entry()
x86, ioapic: Pass struct irq_attr * to setup_ioapic_irq()
apic, i386/bigsmp: Fix false warnings regarding logical APIC ID mismatches
Linus Torvalds [Wed, 26 Oct 2011 15:21:19 +0000 (17:21 +0200)]
Remove stale "depends on NETDEV_1000"in staging drivers
Mark Einon points out that the Kconfig option for NETDEV_1000 no longer
exists, and the merge of the staging drivers should have removed that
for the et131x driver.
And while checking for it, I noticed that slicoss had the same stale
dependency. Remove that one too.
Reported-by: Mark Einon <mark.einon@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 26 Oct 2011 15:15:03 +0000 (17:15 +0200)]
Merge branch 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...