Stefan Richter [Wed, 7 Oct 2009 22:39:31 +0000 (00:39 +0200)]
firewire: sbp2: provide fallback if mgt_ORB_timeout is missing
The Unit_Characteristics entry of an SBP-2 unit directory is not
mandatory as far as I can tell. If it is missing, we would probably
fail to log in into the target because firewire-sbp2 would not wait for
status after it sent the login request.
The fix moves the cleanup of tgt->mgt_orb_timeout into a place where it
is executed exactly once before login, rather than 0..n times depending
on the target's config ROM. With targets with one or more
Unit_Characteristics entries, the result is the same as before.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Jarkko Nikula [Wed, 14 Oct 2009 16:56:35 +0000 (09:56 -0700)]
omap: McBSP: Fix incorrect receiver stop in omap_mcbsp_stop
This small typo written by author causes that McBSP receiver is disabled on
OMAP2430 and OMAP3430 even if only transmitter is stopped. This was noted
with ALSA SoC where simultaneous recording halted if playback was stopped
first.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Aaro Koskinen [Wed, 14 Oct 2009 16:56:34 +0000 (09:56 -0700)]
omap: RX-51: Drop I2C-1 speed to 2200
The I2C-1 bus frequency on RX-51 should be 2.2 MHz. The speed is limited
by TWL5030/GAIA; a higher speed could lead to errors on the interface. The
maximum speed depends on the system clock for GAIA: 2.2 MHz (if 19.2 MHz),
2.4 MHz (26 MHz) or 2.9 MHz (38.4 MHz).
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Sanjeev Premi [Wed, 14 Oct 2009 16:56:33 +0000 (09:56 -0700)]
omap: CONFIG_ISP1301_OMAP redefined in Beagle defconfig
The symbol CONFIG_ISP1301_OMAP was defined twice in the
defconfig. This was causing the warning:
arch/arm/configs/omap3_beagle_defconfig:972:warning:
override: reassigning to symbol ISP1301_OMAP
Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Chris Mason [Wed, 14 Oct 2009 13:38:28 +0000 (09:38 -0400)]
Btrfs: always pin metadata in discard mode
We have an optimization in btrfs to allow blocks to be
immediately freed if they were allocated in this transaction and never
written. Otherwise they are pinned and freed when the transaction
commits.
This isn't optimal for discard mode because immediately freeing
them means immediately discarding them. It is better to give the
block to the pinning code and letting the (slow) discard happen later.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The discard support code in btrfs currently is guarded by ifdefs for
BIO_RW_DISCARD, which is never defines as it's the name of an enum
memeber. Just remove the useless ifdefs to actually enable the code.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Enable discard by default is not a good idea given the the trim speed
of SSD prototypes we've seen, and the carecteristics for many high-end
arrays. Turn of discards by default and require the -o discard option
to enable them on.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Wed, 14 Oct 2009 13:24:59 +0000 (09:24 -0400)]
Btrfs: properly wait log writers during log sync
A recently fsync optimization make btrfs_sync_log skip calling
wait_for_writer in the single log writer case. This is incorrect
since the writer count can also be increased by btrfs_pin_log.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Tue, 13 Oct 2009 20:46:49 +0000 (16:46 -0400)]
Btrfs: fix possible ENOSPC problems with truncate
There's a problem where we don't do any space reservation for truncates, which
can cause you to OOPs because you will be allowed to go off in the weeds a bit
since we don't account for the delalloc bytes that are created as a result of
the truncate.
Signed-off-by: Josef Bacik <jbacik@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
The name showed up in /proc/interrupts also needs a change. I use
PMI (Performance monitoring interrupt) here, since it is the
official name used in Intel's documents.
Signed-off-by: Li Hong <lihong.hi@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091014105039.GA22670@uhli> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use cio_is_console() in io_subchannel_probe to indicate that the
special handling is console specific. As long as there is no other
subchannel for which this might be true, it is misleading to speak
of "early devices". Should more of these devices be introduced,
a cleanup of all console special handling is in order anyway.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Wed, 14 Oct 2009 10:43:49 +0000 (12:43 +0200)]
[S390] call home support: fix proc handler
8d65af78 "sysctl: remove "struct file *" argument of ->proc_handler"
removed the struct file argument from all proc_handlers but didn't
change the call home proc handler (or call home was merged later).
Stefan Haberland [Wed, 14 Oct 2009 10:43:48 +0000 (12:43 +0200)]
[S390] dasd: use idal for device characteristics
If the rdc_buffer is above 2G we need indirect addresssing so we have
to use an idaw to give the rdc_buffer to the ccw.
If the rdc_buffer is under 2G nothing changes.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Wed, 14 Oct 2009 10:43:45 +0000 (12:43 +0200)]
[S390] tape390: Fix request queue handling in block driver
When setting a channel attached tape online under Linux 2.6.31, the
"vol_id" process from udev hangs in sync_page():
2 sync_page+144 [0x1dfaac]
3 __wait_on_bit_lock+194 [0x58c23e]
4 __lock_page+116 [0x1df9dc]
5 truncate_inode_pages_range+728 [0x1ed7cc]
6 __blkdev_put+244 [0x25f738]
7 __fput+300 [0x229c4c]
8 filp_close+122 [0x225a3a]
The reason for that is an error in the request queue handling. It can
happen that we fetch a request, but do not process it further because
the number of queued requests exceeds TAPEBLOCK_MIN_REQUEUE.
To fix this, we should call blk_peek_request() instead of
blk_fetch_request() in the while condition and fetch the request in
the loop body afterwards.
Michael Holzheu [Wed, 14 Oct 2009 10:43:44 +0000 (12:43 +0200)]
[S390] hypfs: Use subcode 6 if subcode 7 is not available
Hypfs never worked on systems that only provide D204 subcode 6.
In these cases we nevertheless used subcode 7. With this fix, we
use subcode 6, if it is available and the system does not provide
subcode 7.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dmitry Torokhov [Wed, 14 Oct 2009 06:37:30 +0000 (23:37 -0700)]
Input: fix locking issue in /proc/bus/input/ handlers
input_devices_seq_start() uses mutex_lock_interruptible() to acquire
the input_mutex, but doesn't properly handle the situation when the
call fails (for example due to interrupt). Instead of returning NULL
(which indicates that there is no more data) we should return
ERR_PTR()-encoded error.
We also need explicit flag indicating whether input_mutex was acquired
since input_devices_seq_stop() is called whether input_devices_seq_start()
was successful or not.
Dmitry Torokhov [Wed, 14 Oct 2009 06:39:17 +0000 (23:39 -0700)]
Input: atkbd - postpone restoring LED/repeat rate at resume
We need to postpone restoring LED state and typematic settings until
keyboard is finished reconnecting upon resume. Normally driver core
and PM infrastructure takes care of proper ordering and dependencies,
but or case actual reconnect is done asynchronously from kseriod.
So while driver core thinks that keyboard was resumed and it is time
to let input core run it's resume handlers in reality keyboard is not
ready yet. The solution is to keep rescheduling work that adjusts LED
and rate settings until keyboard is fully enabled.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Paul Mundt [Wed, 14 Oct 2009 06:50:28 +0000 (15:50 +0900)]
sh: Fix a TRACE_IRQS_OFF typo.
The resume_userspace path had TRACE_IRQS_OFF written incorrectly and so
never handled the transition properly. This was fixed once before but
seems to have made it back in the tree. Fix it for good.
Paul Mundt [Wed, 14 Oct 2009 05:21:40 +0000 (14:21 +0900)]
sh: Optimize the setup_rt_frame() I-cache flush.
This only needs to flush the return code via the legacy path, and just
invalidates uselessly otherwise. This makes the behaviour consistent for
all of the trampoline setup paths.
Paul Mundt [Wed, 14 Oct 2009 05:14:30 +0000 (14:14 +0900)]
sh: Populate initial secondary CPU info from boot_cpu_data.
The secondary CPU info was seeing corrupted results due to not entering
all of the setup paths taken by the boot CPU. So we just memcpy() the
boot cpu data over directly, and then fix up the per-CPU bits.
making a powerpc target with PCI support, shows the
following warning:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x10430): Section mismatch in reference from the
function pcibios_allocate_bus_resources() to the function .init.text:reparent_resources()
The function pcibios_allocate_bus_resources() references
the function __init reparent_resources().
This is often because pcibios_allocate_bus_resources lacks a __init
annotation or the annotation of reparent_resources is wrong.
This patch fix this warning by removing the __init
annotation before reparent_resources.
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Sean MacLennan [Tue, 29 Sep 2009 06:00:06 +0000 (06:00 +0000)]
powerpc: warning: allocated section `.data_nosave' not in segment
We need to align before the output section. Having the align inside
the output section causes the linker to put some filler in there,
which makes it a non-empty section, but this section isn't assigned to
a segment so you get a warning from the linker.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Acked-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Vorontsov [Thu, 1 Oct 2009 08:38:49 +0000 (08:38 +0000)]
powerpc/kgdb: Fix build failure caused by "kgdb.c: unused variable 'acc'"
'acc' isn't used anywhere and thus triggers gcc warning, which causes
build error with CONFIG_PPC_DISABLE_WERROR=n (default):
cc1: warnings being treated as errors
arch/powerpc/kernel/kgdb.c: In function 'gdb_regs_to_pt_regs':
arch/powerpc/kernel/kgdb.c:289: warning: unused variable 'acc'
make[1]: *** [arch/powerpc/kernel/kgdb.o] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sun, 11 Oct 2009 21:47:34 +0000 (21:47 +0000)]
powerpc: Fix hypervisor TLB batching
Profiling of a page fault scalability microbenchmark shows flush_hash_range
is not calling the batch hpte invalidate hcall (H_BULK_REMOVE).
It turns out we have a duplicate firmware feature for hcall-bulk and the
current setup code stops after finding the first match. This meant we never
batch and always do individual invalidates.
The patch below removes the duplicate and shifts FW_FEATURE_CMO to close
the gap. With the patch applied the single threaded page fault rate improves
from 217169 to 238755 per second on a POWER5 test box, a 10% improvement.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/mm: Fix hang accessing top of vmalloc space
On pSeries, we always force the IO space to be mapped using 4K
pages even with a 64K base page size to cope with some limitations
in the HV interface to some devices.
However, the SLB miss handler code to discriminate between vmalloc
and ioremap space uses a CPU feature section such that the code
is nop'ed out when the processor support large pages non-cachable
mappings.
Thus, we end up always using the ioremap page size for vmalloc
segments on such processors, causing a discrepency between the
segment and the hash table, and thus a hang continously hashing
the page.
It works for the first segment of the vmalloc space since that
segment is "bolted" in by C code correctly, and thankfully we
almost never use the vmalloc space beyond the first segment,
but the new percpu code made the bug happen.
This fixes it by removing the feature section from the assembly,
we now always do the comparison between vmalloc and ioremap.
Signed-off-by; Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pmac: Fix issues with sleep on some powerbooks
Since the change of how interrupts are disabled during suspend,
certain PowerBook models started exhibiting various issues during
suspend or resume from sleep.
I finally tracked it down to the code that runs various "platform"
functions (kind of little scripts extracted from the device-tree),
which uses our i2c and PMU drivers expecting interrutps to work,
and at a time where with the new scheme, they have been disabled.
This causes timeouts internally which for some reason results in
the PMU being unable to see the trackpad, among other issues, really
it depends on the machine. Most of the time, we fail to properly adjust
some clocks for suspend/resume so the results are not always
predictable.
This patch fixes it by using IRQF_TIMER for both the PMU and the I2C
interrupts. I prefer doing it this way than moving the call sites since
I really want those platform functions to still be called after all
drivers (and before sysdevs).
We also do a slight cleanup to via-pmu.c driver to make sure the
ADB autopoll mask is handled correctly when doing bus resets
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt [Tue, 15 Sep 2009 15:30:14 +0000 (08:30 -0700)]
powerpc64/ftrace: use PACA to retrieve TOC in mod_return_to_handler
The mod_return_to_handler needs to switch to the kernel TOC before
jumping to a the kernel code. It currently does this by looking
at the kernel function data and retrieves the TOC that way.
Not only is this inefficient, it also breaks with a relocatable kernel.
The PACA contains the kernel TOC and we can easily retrieve it that
way.
Reported-by: Sachin Sant <sachinp@in.ibm.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Tue, 15 Sep 2009 15:20:15 +0000 (08:20 -0700)]
powerpc/ftrace: show real return addresses in modules
When the function graph tracer is enabled, it replaces the return address
with a hook back to the tracer. This makes back traces see the hook instead
of the actual return address.
The current code also shows the real address by checking if the return
address jumps to the return_to_handler. If it is, is also prints out
the saved real return address.
On powerpc64, some modules may return to mod_return_to_handler, which
is not checked. This patch will also show the real address if a return
is to mod_return_to_handler as well.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Sriram [Wed, 7 Oct 2009 02:44:30 +0000 (02:44 +0000)]
TI DaVinci EMAC: Clear statistics register properly.
The mechanism to clear the statistics register is dependent
on the status of GMIIEN bit in MAC control register. If the
GMIIEN bit is set, the stats registers are write to decrement.
If the GMIIEN bit is cleared, the stats registers are plain
read/write registers. The stats register clearing operation
must take into account the current state of GMIIEN as it
can be cleared when the interface is brought down.
With existing implementation logic, querying for interface stats
when the interface is down, can corrupt the statistics counters.
This patch examines the GMIIEN bit status in MAC_CONTROL
register before choosing an appropriate mask for clearing stats
registers.
Signed-off-by: Sriramakrishnan <srk@ti.com> Acked-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Wed, 7 Oct 2009 12:44:20 +0000 (12:44 +0000)]
r8169: partial support and phy init for the 8168d
Extracted from Realtek's 8.012.00 r8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Tested-by: Simon Farnsworth <simon.farnsworth@onelan.com> Cc: Edward Hsu <edward_hsu@realtek.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Torokhov [Tue, 13 Oct 2009 05:47:25 +0000 (22:47 -0700)]
Input: atkbd - restore resetting LED state at startup
Fix breakage caused by commit 9605fb48e1998935a5ee70c965f90ad1ac023add
While the input core indeed takes care of restoring led state and
typematic settings upon resume the driver still need to initialize
them properly when registering a new device
Chris Mason [Tue, 13 Oct 2009 17:29:19 +0000 (13:29 -0400)]
Btrfs: streamline tree-log btree block writeout
Syncing the tree log is a 3 phase operation.
1) write and wait for all the tree log blocks for a given root.
2) write and wait for all the tree log blocks for the
tree of tree log roots.
3) write and wait for the super blocks (barriers here)
This isn't as efficient as it could be because there is
no requirement to wait for the blocks from step one to hit the disk
before we start writing the blocks from step two. This commit
changes the sequence so that we don't start waiting until
all the tree blocks from both steps one and two have been sent
to disk.
We do this by breaking up btrfs_write_wait_marked_extents into
two functions, which is trivial because it was already broken
up into two parts.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Tue, 13 Oct 2009 17:21:08 +0000 (13:21 -0400)]
Btrfs: avoid tree log commit when there are no changes
rpm has a habit of running fdatasync when the file hasn't
changed. We already detect if a file hasn't been changed
in the current transaction but it might have been sent to
the tree-log in this transaction and not changed since
the last call to fsync.
In this case, we want to avoid a tree log sync, which includes
a number of synchronous writes and barriers. This commit
extends the existing tracking of the last transaction to change
a file to also track the last sub-transaction.
The end result is that rpm -ivh and -Uvh are roughly twice as fast,
and on par with ext3.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Tue, 13 Oct 2009 16:55:09 +0000 (12:55 -0400)]
Btrfs: only write one super copy during fsync
During a tree-log commit for fsync, we've been writing at least
two copies of the super block and forcing them to disk.
The other filesystems write only one, and this change brings us on
par with them. A full transaction commit will write all the super
copies, so we still have redundant info written on a regular
basis.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Tue, 13 Oct 2009 17:21:33 +0000 (10:21 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: Add cciss_allow_hpsa module parameter
cciss: Fix multiple calls to pci_release_regions
blk-settings: fix function parameter kernel-doc notation
writeback: kill space in debugfs item name
writeback: account IO throttling wait as iowait
elv_iosched_store(): fix strstrip() misuse
cfq-iosched: avoid probable slice overrun when idling
cfq-iosched: apply bool value where we return 0/1
cfq-iosched: fix think time allowed for seekers
cfq-iosched: fix the slice residual sign
cfq-iosched: abstract out the 'may this cfqq dispatch' logic
block: use proper BLK_RW_ASYNC in blk_queue_start_tag()
block: Seperate read and write statistics of in_flight requests v2
block: get rid of kblock_schedule_delayed_work()
cfq-iosched: fix possible problem with jiffies wraparound
cfq-iosched: fix issue with rq-rq merging and fifo list ordering
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: revert "save ARCH & CROSS_COMPILE ..."
warn about use of uninstalled kernel headers
kbuild: mkcompile_h: trivial cleanups
kbuild: fix warning when domainname is not available
kbuild: Fix size_append issue for bzip2/lzma kernel
kbuild,scripts: use non-builtin echo for '-e'
kbuild: fix the binrpm-pkg target to work with KBUILD_OUTPUT set
Ingo Molnar [Mon, 12 Oct 2009 14:22:46 +0000 (16:22 +0200)]
headers: Fix build after <linux/sched.h> removal
Commit d43c36dc6b357fa1806800f18aa30123c747a6d1 ("headers: remove
sched.h from interrupt.h") left some build errors in some configurations
due to drivers having depended on getting header files "accidentally".
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Combined several one-liners from Ingo into one single patch - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 13 Oct 2009 17:10:33 +0000 (10:10 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix possible deadlock in hidraw_read
HID: fix kerneldoc comment for hid_input_report()
HID: add __init/__exit macros to twinhan.c
Linus Torvalds [Tue, 13 Oct 2009 17:10:18 +0000 (10:10 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Allow all formats as default for Nvidia HDMI
ALSA: aaci: ARM1176 aaci-pl041 AC97 register read timeout
ALSA: hda - Fix volume-knob setup for Dell laptops with STAC9228
ALSA: hda - Fix mute sound with STAC9227/9228 codecs
ALSA: bt87x - Add a whitelist for Pinnacle PCTV (11bd:0012)
ALSA: hda - Fix overflow of spec->init_verbs in patch_realtek.c
ALSA: ice1724 - Make call to set hw params succeed on ESI Juli@
ALSA: ice1724: Fix surround on Chaintech AV-710
ALSA: hda - Add full rates/formats support for Nvidia HDMI
Linus Torvalds [Tue, 13 Oct 2009 17:05:36 +0000 (10:05 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
ext3: Update documentation about ext3 quota mount options
ext3: Don't update superblock write time when filesystem is read-only
Linus Torvalds [Tue, 13 Oct 2009 17:04:40 +0000 (10:04 -0700)]
Merge git://git.infradead.org/~dwmw2/iommu-2.6.32
* git://git.infradead.org/~dwmw2/iommu-2.6.32:
x86: Move pci_iommu_init to rootfs_initcall()
Run pci_apply_final_quirks() sooner.
Mark pci_apply_final_quirks() __init rather than __devinit
Rename pci_init() to pci_apply_final_quirks(), move it to quirks.c
intel-iommu: Yet another BIOS workaround: Isoch DMAR unit with no TLB space
intel-iommu: Decode (and ignore) RHSA entries
intel-iommu: Make "Unknown DMAR structure" message more informative
Takashi Iwai [Tue, 13 Oct 2009 14:07:59 +0000 (16:07 +0200)]
ALSA: hda - Allow all formats as default for Nvidia HDMI
In the commit f0613d5752d8f7d1d02e6d40947f38877fdf9c90
ALSA: hda - Add full rates/formats support for Nvidia HDMI
the flag LIMITIED_RATE_FMT_SUPPORT was set as default, as I forgot
to clear before commit.
After a reboot on an ARM1176 which amounts to a softreset, it has been
noted that the ALSA driver does not get registered and the probe fails
with the error "aaci-pl041 fpga:04: ac97 read back fail". In the process
of reading from a register the SL1TxBusy bit is set indicating that the
transceiver is busy and remains so until the default timeout occurs.
Set the Power down register 0x26 to an arbitrary value as specified in
the PL041 manual (page: 3-18) so that AACISL1TX/AACISL2TX registers take
their default state.
Signed-off-by: Philby John <pjohn@in.mvista.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Sun, 11 Oct 2009 15:38:29 +0000 (17:38 +0200)]
ALSA: hda - Fix mute sound with STAC9227/9228 codecs
On FSC laptops, the sound gets muted gradually when the volume is chnaged.
This is due to the wrong volume-knob widget setup. The delta bit (bit 7)
shouldn't be set for these devices.
This patch adds a new quirk to set the value 0x7f to the widget 0x24
instead of 0xff.
Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Willy Tarreau [Tue, 13 Oct 2009 07:27:40 +0000 (00:27 -0700)]
tcp: fix tcp_defer_accept to consider the timeout
I was trying to use TCP_DEFER_ACCEPT and noticed that if the
client does not talk, the connection is never accepted and
remains in SYN_RECV state until the retransmits expire, where
it finally is deleted. This is bad when some firewall such as
netfilter sits between the client and the server because the
firewall sees the connection in ESTABLISHED state while the
server will finally silently drop it without sending an RST.
This behaviour contradicts the man page which says it should
wait only for some time :
TCP_DEFER_ACCEPT (since Linux 2.4)
Allows a listener to be awakened only when data arrives
on the socket. Takes an integer value (seconds), this
can bound the maximum number of attempts TCP will
make to complete the connection. This option should not
be used in code intended to be portable.
Also, looking at ipv4/tcp.c, a retransmit counter is correctly
computed :
case TCP_DEFER_ACCEPT:
icsk->icsk_accept_queue.rskq_defer_accept = 0;
if (val > 0) {
/* Translate value in seconds to number of
* retransmits */
while (icsk->icsk_accept_queue.rskq_defer_accept < 32 &&
val > ((TCP_TIMEOUT_INIT / HZ) <<
icsk->icsk_accept_queue.rskq_defer_accept))
icsk->icsk_accept_queue.rskq_defer_accept++;
icsk->icsk_accept_queue.rskq_defer_accept++;
}
break;
==> rskq_defer_accept is used as a counter of retransmits.
But in tcp_minisocks.c, this counter is only checked. And in
fact, I have found no location which updates it. So I think
that what was intended was to decrease it in tcp_minisocks
whenever it is checked, which the trivial patch below does.
Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Rankin [Tue, 13 Oct 2009 07:32:02 +0000 (00:32 -0700)]
net: Teach pegasus driver to ignore bluetoother adapters with clashing Vendor:Product IDs
The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: Chris Rankin <rankincj@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Mon, 12 Oct 2009 05:27:48 +0000 (05:27 +0000)]
libertas: fix build
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
x86/paravirt: Use normal calling sequences for irq enable/disable
Bastian Blank reported a boot crash with stackprotector enabled,
and debugged it back to edx register corruption.
For historical reasons irq enable/disable/save/restore had special
calling sequences to make them more efficient. With the more
recent introduction of higher-level and more general optimisations
this is no longer necessary so we can just use the normal PVOP_
macros.
This fixes some residual bugs in the old implementations which left
edx liable to inadvertent clobbering. Also, fix some bugs in
__PVOP_VCALLEESAVE which were revealed by actual use.
Add cciss_allow_hpsa module parameter. This parameter causes
the cciss driver to ignore any Smart Array devices known to be
supported by the hpsa driver.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix multiple calls to pci_release_regions. If cciss_pci_init
fails, it already does any necessary call to pci_release_regions,
so this does not need to be done again in cciss_init_one in that
case.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: Ronghua Zhang <ronghua@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Sanders [Tue, 13 Oct 2009 07:03:11 +0000 (00:03 -0700)]
net: Fix IXP 2000 network driver building.
The IXP 2000 network driver was failing to build as it has its own
statistics gathering which was not compatible with the recent network
device operations changes. This patch fixes the driver in the obvious
way and has been compile tested. I have been unable to get the ixp2000
maintainer to comment or test this fix.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Bader [Fri, 21 Aug 2009 09:03:05 +0000 (11:03 +0200)]
ACPI: video: Loosen strictness of video bus detection code
BugLink: http://bugs.launchpad.net/bugs/333386
Currently a video bus device must (beside other criteria) define _DOD and
_DOS methods to be considered a video device.
Some broken BIOSes prevented working backlight control by only defining both
for one (non-existing bus) and only _DOD for the rest. With this patch in
place the other bus definitions were considered too and backlight control
started to work again.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Darren Salt [Mon, 12 Oct 2009 22:13:33 +0000 (00:13 +0200)]
eeepc-laptop: Prevent a panic when disabling RT2860 wireless when associated
This works around what I think is actually a bug in rt2860sta which is
triggered when the hardware "disappears" from beneath the driver, i.e. when
wireless is toggled off via ACPI. It does so by ensuring that the rfkill
soft-block flag is set before the hardware is disabled.
I do not know whether this patch is required if rt2800pci is in use instead
of rt2860sta; at the time of submission of this patch, I've not been able to
test this.
Currently the annotation for function eeepc_enable_camera() is
__init, and refers to a
function eeepc_hotk_add() which is non-init. Use __devinit for both
functions which is
more appropriate and fixes a section mismatch warning.
We were warned by the following warning:
LD drivers/platform/x86/built-in.o
WARNING: drivers/platform/x86/built-in.o(.text+0x12e1): Section
mismatch in reference from the function eeepc_hotk_add() to the
function .init.text:eeepc_enable_camera()
The function eeepc_hotk_add() references
the function __init eeepc_enable_camera().
This is often because eeepc_hotk_add lacks a __init
annotation or the annotation of eeepc_enable_camera is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com> Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com>
acpi_get_pci_dev() may be called for a non-PCI device, in which case
it should return NULL. However, it assumes that every handle it
finds in the ACPI CA name space, between given device handle and the
PCI root bridge handle, corresponds to a PCI-to-PCI bridge with an
existing secondary bus. For this reason, when it finds a struct
pci_dev object corresponding to one of them, it doesn't check if
its 'subordinate' field is a valid pointer. This obviously leads to
a NULL pointer dereference if acpi_get_pci_dev() is called for a
non-PCI device with a PCI parent which is not a bridge.
To fix this issue make acpi_get_pci_dev() check if pdev->subordinate
is not NULL for every device it finds on the path between the root
bridge and the device it's supposed to get to and return NULL if the
"target" device cannot be found.
http://bugzilla.kernel.org/show_bug.cgi?id=14129
(worked in 2.6.30, regression in 2.6.31)
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-by: Danny Feng <dfeng@redhat.com> Reviewed-by: Alex Chiang <achiang@hp.com> Tested-by: chepioq <chepioq@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Dmitry Torokhov [Tue, 13 Oct 2009 04:35:00 +0000 (21:35 -0700)]
Input: synaptics - add another Protege M300 to rate blacklist
Apparently some of Toshiba Protege M300 identify themselves as
"Portable PC" in DMI so we need to add that to the DMI table as
well. We need DMI data so we can automatically lower Synaptics
reporting rate from 80 to 40 pps to avoid over-taxing their
keyboard controllers.
Tested-by: Rod Davison <roddavison@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Paul Mundt [Tue, 13 Oct 2009 03:42:48 +0000 (12:42 +0900)]
sh: ftrace: Fix up syscall tracepoint support.
Sync up with latest core changes in the syscalls tracing area:
- tracing: Map syscall name to number (syscall_name_to_nr())
- tracing: Call arch_init_ftrace_syscalls at boot
- tracing: add support tracepoint ids (set_syscall_{enter,exit}_id())
Paul Mundt [Tue, 13 Oct 2009 02:18:34 +0000 (11:18 +0900)]
sh: force dcache flush if dcache_dirty bit set.
This too follows the ARM change, given that the issue at hand applies to
all platforms that implement lazy D-cache writeback.
This fixes up the case when a page mapping disappears between the
flush_dcache_page() call (when PG_dcache_dirty is set for the page) and
the update_mmu_cache() call -- such as in the case of swap cache being
freed early. This kills off the mapping test in update_mmu_cache() and
switches to simply testing for PG_dcache_dirty.
projects / mv-sheeva.git / log