This patch contains a bugfix for TMR LUN_RESET related to TRANSPORT_FREE_CMD_INTR
operation, where core_tmr_drain_cmd_list() will now skip processing for this
case to prevent an ABORT_TASK status from being returned for descriptors that
are already queued up to be released by processing thread context.
Cc: Roland Dreier <roland@purestorage.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug where transport_send_task_abort() could be called
during LUN_RESET to return SAM_STAT_TASK_ABORTED + tfo->queue_status(), when
SCF_SENT_CHECK_CONDITION -> tfo->queue_status() has already been sent from
within another context via transport_send_check_condition_and_sense().
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug in LUN_RESET operation with transport_cmd_finish_abort()
where transport_remove_cmd_from_queue() was incorrectly being called, causing
descriptors with t_state == TRANSPORT_FREE_CMD_INTR to be incorrectly removed
from qobj->qobj_list during process context release. This change ensures the
descriptor is only removed via transport_remove_cmd_from_queue() when doing a
direct release via transport_generic_remove().
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addresses a bug with the lio-core-2.6.git conversion of
transport_add_cmd_to_queue() to use a single embedded list_head, instead
of individual struct se_queue_req allocations allowing a single se_cmd to
be added to the queue mulitple times. This was changed in the following:
The problem is that some target code still assumes performing multiple
adds is allowed via transport_add_cmd_to_queue(), which ends up causing
list corruption in qobj->qobj_list code. This patch addresses this
by removing an existing struct se_cmd from the list before the add, and
removes an unnecessary list walk in transport_remove_cmd_from_queue()
It also changes cmd->t_transport_queue_active to use explict sets intead
of increment/decrement to prevent confusion during exception path handling.
Signed-off-by: Roland Dreier <roland@purestorage.com> Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the old Conexant chips (5045, 5047, 5051 and 5066), a single EAPD
may handle both headphone and speaker outputs while it's assigned only
to one of them. Turning off dynamically leads to the unexpected silent
output in such a configuration with the auto-mute function.
Since it's difficult to know how the EAPD is handled in the actual h/w
implementation, better to keep EAPD on while running for such codecs.
The purpose of this patch is to remove a section of "bad" code that
assigns the last DAC to ports E or F in order to support notebooks
with docking in earlier days, around ALSA 1.0.19 - 21. This is not
necessary now and actually breaks some configurations that use these
ports as other devices. This have been tested on several different
configurations to make sure that it is working for different combinations.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Besides being unnecessary, it is too small (currently truncates
responses to 60 bytes). The mid-layer will have already allocated a
sufficiently sized buffer, just kmap and copy into it directly.
Reported-by: Derick Marks <derick.w.marks@intel.com> Tested-by: Derick Marks <derick.w.marks@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During kdump testing I noticed timeouts when initialising each IPR
adapter. While the driver has logic to detect an adapter in an
indeterminate state, it wasn't triggering and each adapter went
through a 5 minute timeout before finally going operational.
Some analysis showed the needs_hard_reset flag wasn't getting set.
We can check the reset_devices kernel parameter which is set by
kdump and force a full reset. This fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch for megaraid_sas will fix a potential bad pointer access
in megasas_reset_timer(), when a MegaRAID 9265/9285 or 9360/9380 gets a
timeout. megasas_build_io_fusion() sets SCp.ptr to be a struct
megasas_cmd_fusion *, but then megasas_reset_timer() was casting SCp.ptr to be
a struct megasas_cmd *, then trying to access cmd->instance, which is invalid.
Just loading instance from scmd->device->host->hostdata in
megasas_reset_timer() fixes the issue.
Signed-off-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 15bed0f2f added a quirk for the e823 Ricoh card reader to lower the
base frequency. However, the quirk first checks to see if the proprietary
MMC controller is disabled, and returns if so. On some devices, such as the
Lenovo X220, the MMC controller is already disabled by firmware it seems,
but the frequency change is still needed so sdhci-pci can talk to the cards.
Since the MMC controller is disabled, the frequency fixup was never being run
on these machines.
This moves the e823 check above the MMC controller check so that it always
gets run.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.
The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com> Acked-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.
If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.
Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
Commit 9b9fe724 accidentally used RADEON_GPIO_EN_* where
RADEON_GPIO_MASK_* was intended. This caused improper initialization
of I2C buses, mostly visible when setting i2c_algo_bit.bit_test=1.
Using the right constants fixes the problem.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: Jerome Glisse <j.glisse@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When force == false, we don't do load detection in the connector
detect functions. Unforunately, we also return the previous
connector state so we never get disconnect events for DVI-I, DVI-A,
or VGA. Save whether we detected the monitor via load detection
previously and use that to determine whether we return the previous
state or not.
DVI-D and HDMI-A are digital only, so there's no need to
attempt analog load detect. Also, skip bail before the
!force check, or we fail to get a disconnect events.
The next patches in the series attempt to fix disconnect
events for connectors with analog support (DVI-I, HDMI-B,
DVI-A).
The commit 47356eb67285014527a5ab87543ba1fae3d1e10a introduced a
mechanism to record the backlight level only at disabling time, but it
also introduced a regression. Since intel_lvds_enable() may be called
without disabling (e.g. intel_lvds_commit() calls it unconditionally),
the backlight gets back to the last recorded value. For example, this
happens when you dim the backlight, close the lid and open the lid,
then the backlight suddenly goes to the brightest.
This patch fixes the bug by recording the backlight level always
when changed via intel_panel_set_backlight(). And,
intel_panel_{enable|disable}_backlight() call the internal function not
to update the recorded level wrongly.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Keith Packard <keithp@keithp.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Talking to the eDP DDC channel requires that the panel be powered
up. Wrap both the EDID and modes fetch code with calls to turn the vdd
power on and back off.
Signed-off-by: Keith Packard <keithp@keithp.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting the chain (CH) bit in the link TRB of isochronous transfer rings
is required by AMD 0.96 xHCI host controller to successfully transverse
multi-TRB TD that span through different memory segments.
When a Missed Service Error event occurs, if the chain bit is not set in
the link TRB and the host skips TDs which just across a link TRB, the
host may falsely recognize the link TRB as a normal TRB. You can see
this may cause big trouble - the host does not jump to the right address
which is pointed by the link TRB, but continue fetching the memory which
is after the link TRB address, which may not even belong to the host,
and the result cannot be predicted.
This causes some big problems. Without the former patch I sent: "xHCI:
prevent infinite loop when processing MSE event", the system may hang.
With that patch applied, system does not hang, but the host still access
wrong memory address and isoc transfer will fail. With this patch,
isochronous transfer works as expected.
This patch should be applied to kernels as old as 2.6.36, which was when
the first isochronous support was added for the xHCI host controller.
There are 2 situations wherein the xhci_ring* might not get freed:
- When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and
we goto the fail: label in xhci_ring_alloc. In this case, the ring
will not get kfreed.
- When the num_segs argument to xhci_ring_alloc is passed as 0 and
we try to free the rung after that.
( This doesn't really happen as of now in the code but we seem to
be entertaining num_segs=0 in xhci_ring_alloc )
This should be backported to kernels as old as 2.6.31.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1489) works around a hardware bug in MosChip EHCI
controllers. Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter). If the register is read at just the wrong time, the value
obtained is too low by 8.
When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0. This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Jason N Pitt <jpitt@fhcrc.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It will break the pxa serial driver when the system resumes from suspend mode
as it will try to set baud rate divider register in set_termios but with
clock off. The register value can not be set correctly on some platform if
the clock is disabled. The pxa driver will check the value and report the
following warning:
------------[ cut here ]------------
WARNING: at drivers/tty/serial/pxa.c:545 serial_pxa_set_termios+0x1dc/0x250()
Modules linked in:
[<c0281f30>] (unwind_backtrace+0x0/0xf0) from [<c029341c>] (warn_slowpath_common+0x4c/0x64)
[<c029341c>] (warn_slowpath_common+0x4c/0x64) from [<c029344c>] (warn_slowpath_null+0x18/0x1c)
[<c029344c>] (warn_slowpath_null+0x18/0x1c) from [<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250)
[<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250) from [<c044a840>] (uart_resume_port+0x128/0x2dc)
[<c044a840>] (uart_resume_port+0x128/0x2dc) from [<c044bbe0>] (serial_pxa_resume+0x18/0x24)
[<c044bbe0>] (serial_pxa_resume+0x18/0x24) from [<c0454d34>] (platform_pm_resume+0x40/0x4c)
[<c0454d34>] (platform_pm_resume+0x40/0x4c) from [<c0457ebc>] (pm_op+0x68/0xb4)
[<c0457ebc>] (pm_op+0x68/0xb4) from [<c0458368>] (device_resume+0xb0/0xec)
[<c0458368>] (device_resume+0xb0/0xec) from [<c04584c8>] (dpm_resume+0xe0/0x194)
[<c04584c8>] (dpm_resume+0xe0/0x194) from [<c0458588>] (dpm_resume_end+0xc/0x18)
[<c0458588>] (dpm_resume_end+0xc/0x18) from [<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac)
[<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac) from [<c02c5278>] (enter_state+0xac/0xdc)
[<c02c5278>] (enter_state+0xac/0xdc) from [<c02c48ec>] (state_store+0xa0/0xbc)
[<c02c48ec>] (state_store+0xa0/0xbc) from [<c0408f7c>] (kobj_attr_store+0x18/0x1c)
[<c0408f7c>] (kobj_attr_store+0x18/0x1c) from [<c034a6a4>] (sysfs_write_file+0x108/0x140)
[<c034a6a4>] (sysfs_write_file+0x108/0x140) from [<c02fb798>] (vfs_write+0xac/0x134)
[<c02fb798>] (vfs_write+0xac/0x134) from [<c02fb8cc>] (sys_write+0x3c/0x68)
[<c02fb8cc>] (sys_write+0x3c/0x68) from [<c027c700>] (ret_fast_syscall+0x0/0x2c)
---[ end trace 88289eceb4675b04 ]---
This patch fix the problem by adding the power on opertion back for uart
console when console_suspend_enabled is true.
netif_notify_peers() caused a kernel warning in netvsc_linkstatus_callback(),
because netvsc_linkstatus_callback() is within IRQ context. So we move
the first call to netif_notify_peers() into queued work as well, but with
zero delay.
In addition to "staging-next", this should also be back-ported to stable
kernels 2.6.32 and later.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a LUN larger than 2 TB is attached to a Linux VM on Hyper-V, we currently
report a maximum size of 2 TB. This patch resolves the issue in hv_storvsc.
Thanks to Robert Scheck <robert.scheck@etes.de> for reporting the issue.
Reported-by: Robert Scheck <robert.scheck@etes.de> Signed-off-by: Mike Sterling <mike.sterling@microsoft.com> Signed-off-by: K.Y. Srinivasan <kys@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the usermode app does an ioctl over this serial device by
using TIOCMIWAIT, then the code will wait by setting the current
task state to TASK_INTERRUPTIBLE and then calling schedule().
This will be woken up by the qt2_process_modem_status on URB
completion when the port_extra->shadowMSR is set to the new
modem status.
However, this could result in a lost wakeup scenario due to a race
in the logic in the qt2_ioctl(TIOCMIWAIT) loop and the URB completion
for new modem status in qt2_process_modem_status.
Due to this, the usermode app's task will continue to sleep despite a
change in the modem status.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The serqt_usb2 driver will not work properly with the ssu100 device
even though it claims to support it. The ssu100 is supported by the
ssu100 driver in mainline so there is no need to have it claimed by
serqt_usb2.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert changes in definitions that were submitted on May 11 2011 and
committed on June 7 2011. No reason for the change in these values was
given in the patch comment, it broke compatibility with older
versions, and was difficult to detect by the simultaneous move of the
lines of code.
Signed-off-by: Alexander Thomas <alexander.thomas@esaturnus.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A return value of -EINPROGRESS from pm_runtime_get indicates that
the device is already resuming due to a previous call. Internally,
usb_autopm_get_interface_async doesn't treat this as an error and
increments the usage count, but passes the error status along
to the caller. The logical assumption of the caller is that
any negative return value reflects the device not resuming
and the pm_usage_cnt not being incremented. Since the usage count
is being incremented and the device is resuming, return success (0)
instead.
Signed-off-by: James Wylder <james.wylder@motorola.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If tty_add_file fails at the point it is now, we have to revert all
the changes we did to the tty. It means either decrease all refcounts
if this was a tty reopen or delete the tty if it was newly allocated.
There was a try to fix this in v3.0-rc2 using tty_release in 0259894c7
(TTY: fix fail path in tty_open). But instead it introduced a NULL
dereference. It's because tty_release dereferences
filp->private_data, but that one is set even in our tty_add_file. And
when tty_add_file fails, it's still NULL/garbage. Hence tty_release
cannot be called there.
To circumvent the original leak (and the current NULL deref) we split
tty_add_file into two functions, making the latter non-failing. In
that case we may do the former early in open, where handling failures
is easy. The latter stays as it is now. So there is no change in
functionality.
The original bug (leak) was introduced by f573bd176 (tty: Remove
__GFP_NOFAIL from tty_add_file()). Thanks Dan for reporting this.
Later, we may split tty_release into more functions and call only some
of them in this fail path instead. (If at all possible.)
Introduced-in: v2.6.37-rc2 Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When tty_driver_lookup_tty fails in tty_open, we forget to drop a
reference to the tty driver. This was added by commit 4a2b5fddd5 (Move
tty lookup/reopen to caller).
Fix that by adding tty_driver_kref_put to the fail path.
I will refactor the code later. This is for the ease of backporting to
stable.
We should call cifs_all_info_to_fattr in rc == 0 case only.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Mon, 24 Oct 2011 05:08:24 +0000 (07:08 +0200)]
Merge git://git.infradead.org/iommu-2.6
* git://git.infradead.org/iommu-2.6:
intel-iommu: fix superpage support in pfn_to_dma_pte()
intel-iommu: set iommu_superpage on VM domains to lowest common denominator
intel-iommu: fix return value of iommu_unmap() API
MAINTAINERS: Update VT-d entry for drivers/pci -> drivers/iommu move
intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.
intel-iommu: Workaround IOTLB hang on Ironlake GPU
intel-iommu: Fix AB-BA lockdep report
Takashi Iwai [Sun, 23 Oct 2011 21:19:12 +0000 (23:19 +0200)]
x86: Fix S4 regression
Commit 4b239f458 ("x86-64, mm: Put early page table high") causes a S4
regression since 2.6.39, namely the machine reboots occasionally at S4
resume. It doesn't happen always, overall rate is about 1/20. But,
like other bugs, once when this happens, it continues to happen.
This patch fixes the problem by essentially reverting the memory
assignment in the older way.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: <stable@kernel.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Yinghai Lu <yinghai.lu@oracle.com>
[ We'll hopefully find the real fix, but that's too late for 3.1 now ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When allocating a set of jobs from kc->job_pool, job->master_job must be
set (to point to itself) so that the mempool item gets freed when the
master_job completes.
ARM: S3C24XX: Fix s3c24xx build errors if !CONFIG_PM
v2:
- register_syscore_ops(&s3c24xx_irq_syscore_ops) does not need to be
conditionally compiled out, it is already optimized out on !CONFIG_PM
- fix also s3c2412 and s3c2416 affected by the same build issue
v1:
s3c2440.c fails to build if !CONFIG_PM because in such case
s3c2410_pm_syscore_ops is not defined. Same error should happen also
in s3c2410.c and s3c2442.c
Signed-off-by: Domenico Andreoli <cavokz@gmail.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Nick Bowler [Thu, 20 Oct 2011 12:16:55 +0000 (14:16 +0200)]
crypto: ghash - Avoid null pointer dereference if no key is set
The ghash_update function passes a pointer to gf128mul_4k_lle which will
be NULL if ghash_setkey is not called or if the most recent call to
ghash_setkey failed to allocate memory. This causes an oops. Fix this
up by returning an error code in the null case.
This is trivially triggered from unprivileged userspace through the
AF_ALG interface by simply writing to the socket without setting a key.
The ghash_final function has a similar issue, but triggering it requires
a memory allocation failure in ghash_setkey _after_ at least one
successful call to ghash_update.
Marek Szyprowski [Fri, 21 Oct 2011 09:04:54 +0000 (18:04 +0900)]
ARM: S5P: fix offset calculation on gpio-interrupt
Offsets of the irq controller registers were calculated
correctly only for first GPIO bank. This patch fixes
calculation of the register offsets for all GPIO banks.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fib_rules: fix unresolved_rules counting
r8169: fix wrong eee setting for rlt8111evl
r8169: fix driver shutdown WoL regression.
ehea: Change maintainer to me
pptp: pptp_rcv_core() misses pskb_may_pull() call
tproxy: copy transparent flag when creating a time wait
pptp: fix skb leak in pptp_xmit()
bonding: use local function pointer of bond->recv_probe in bond_handle_frame
smsc911x: Add support for SMSC LAN89218
tg3: negate USE_PHYLIB flag check
netconsole: enable netconsole can make net_device refcnt incorrent
bluetooth: Properly clone LSM attributes to newly created child connections
l2tp: fix a potential skb leak in l2tp_xmit_skb()
bridge: fix hang on removal of bridge via netlink
x25: Prevent skb overreads when checking call user data
x25: Handle undersized/fragmented skbs
x25: Validate incoming call user data lengths
udplite: fast-path computation of checksum coverage
IPVS netns shutdown/startup dead-lock
netfilter: nf_conntrack: fix event flooding in GRE protocol tracker
Jean Delvare [Thu, 20 Oct 2011 07:06:45 +0000 (03:06 -0400)]
hwmon: (w83627ehf) Fix negative 8-bit temperature values
Since 8-bit temperature values are now handled in 16-bit struct
members, values have to be cast to s8 for negative temperatures to be
properly handled. This is broken since kernel version 2.6.39
(commit bce26c58df86599c9570cee83eac58bdaae760e4.)
Hugh Dickins [Wed, 19 Oct 2011 19:50:35 +0000 (12:50 -0700)]
mm: fix race between mremap and removing migration entry
I don't usually pay much attention to the stale "? " addresses in
stack backtraces, but this lucky report from Pawel Sikora hints that
mremap's move_ptes() has inadequate locking against page migration.
mremap's down_write of mmap_sem, together with i_mmap_mutex or lock,
and pagetable locks, were good enough before page migration (with its
requirement that every migration entry be found) came in, and enough
while migration always held mmap_sem; but not enough nowadays, when
there's memory hotremove and compaction.
The danger is that move_ptes() lets a migration entry dodge around
behind remove_migration_pte()'s back, so it's in the old location when
looking at the new, then in the new location when looking at the old.
Either mremap's move_ptes() must additionally take anon_vma lock(), or
migration's remove_migration_pte() must stop peeking for is_swap_entry()
before it takes pagetable lock.
Consensus chooses the latter: we prefer to add overhead to migration
than to mremapping, which gets used by JVMs and by exec stack setup.
Kjetil Oftedal [Wed, 19 Oct 2011 23:20:50 +0000 (16:20 -0700)]
sparc: Add alignment flag to PCI expansion resources
Currently no type of alignment is specified for PCI expansion roms while
parsing the openfirmware tree. This causes calls to pci_map_rom() to fail.
IORESOURCE_SIZEALIGN is the default alignment used for rom resouces in
pci/probe.c, and has been verified to work with various cards on a ultra 10.
Signed-off-By: Kjetil Oftedal <oftedal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Fri, 14 Oct 2011 00:57:45 +0000 (00:57 +0000)]
r8169: fix driver shutdown WoL regression.
Due to commit 92fc43b4159b518f5baae57301f26d770b0834c9 ("r8169: modify the
flow of the hw reset."), rtl8169_hw_reset stomps during driver shutdown on
RxConfig bits which are needed for WOL on some versions of the hardware.
As these bits were formerly set from the r81{0x, 68}_pll_power_down methods,
factor them out for use in the driver shutdown (rtl_shutdown) handler.
I favored __rtl8169_get_wol() -hardware state indication- over
RTL_FEATURE_WOL as the latter has become a good candidate for removal.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Hayes <hayeswang@realtek.com> Tested-by: Marc Ballarin <ballarin.marc@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Cc: Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by: Breno Leitão <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 19 Oct 2011 13:43:24 +0000 (06:43 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/atom: fix handling of FB scratch indices
drm/radeon/kms/DCE4.1: fix Select_CrtcSource EncodeMode setting for DP bridges (v2)
drm/radeon/kms/DCE4.1: ss is not supported on the internal pplls
drm/radeon/kms/DCE4.1: fix dig encoder to transmitter mapping
ttm: Fix error-path using an uninitialized value
Antonio Ospite [Wed, 12 Oct 2011 20:59:26 +0000 (17:59 -0300)]
[media] videodev: fix a NULL pointer dereference in v4l2_device_release()
The change in 8280b66 does not cover the case when v4l2_dev is already
NULL, fix that.
With a Kinect sensor, seen as an USB camera using GSPCA in this context,
a NULL pointer dereference BUG can be triggered by just unplugging the
device after the camera driver has been loaded.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allen Kay [Fri, 14 Oct 2011 19:32:46 +0000 (12:32 -0700)]
intel-iommu: fix superpage support in pfn_to_dma_pte()
If target_level == 0, current code breaks out of the while-loop if
SUPERPAGE bit is set. We should also break out if PTE is not present.
If we don't do this, KVM calls to iommu_iova_to_phys() will cause
pfn_to_dma_pte() to create mapping for 4KiB pages.
Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allen Kay [Fri, 14 Oct 2011 19:32:17 +0000 (12:32 -0700)]
intel-iommu: set iommu_superpage on VM domains to lowest common denominator
set dmar->iommu_superpage field to the smallest common denominator
of super page sizes supported by all active VT-d engines. Initialize
this field in intel_iommu_domain_init() API so intel_iommu_map() API
will be able to use iommu_superpage field to determine the appropriate
super page size to use.
Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allen Kay [Fri, 14 Oct 2011 19:31:54 +0000 (12:31 -0700)]
intel-iommu: fix return value of iommu_unmap() API
iommu_unmap() API expects IOMMU drivers to return the actual page order
of the address being unmapped. Previous code was just returning page
order passed in from the caller. This patch fixes this problem.
Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Roland Dreier [Tue, 11 Oct 2011 00:07:15 +0000 (17:07 -0700)]
MAINTAINERS: Update VT-d entry for drivers/pci -> drivers/iommu move
Commit 166e9278a3f9 ("x86/ia64: intel-iommu: move to drivers/iommu/")
moved the VT-d driver to drivers/iommu, but left the "F:" line in
MAINTAINERS pointing to drivers/pci, which breaks scripts/get_maintainer.pl.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Alex Deucher [Wed, 19 Oct 2011 00:10:05 +0000 (20:10 -0400)]
drm/radeon/kms/atom: fix handling of FB scratch indices
FB scratch indices are dword indices, but we were treating
them as byte indices. As such, we were getting the wrong
FB scratch data for non-0 indices. Fix the indices and
guard the indexing against indices larger than the scratch
allocation.
Fixes memory corruption on some boards if data was written
past the end of the FB scratch array.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Dave Airlie <airlied@redhat.com> Tested-by: Dave Airlie <airlied@redhat.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
pptp_rcv_core() is a nice example of a function assuming everything it
needs is available in skb head.
Reported-by: Bradley Peterson <despite@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KOVACS Krisztian [Tue, 18 Oct 2011 10:17:35 +0000 (10:17 +0000)]
tproxy: copy transparent flag when creating a time wait
The transparent socket option setting was not copied to the time wait
socket when an inet socket was being replaced by a time wait socket. This
broke the --transparent option of the socket match and may have caused
that FIN packets belonging to sockets in FIN_WAIT2 or TIME_WAIT state
were being dropped by the packet filter.
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Mitsuo Hayasaka [Wed, 12 Oct 2011 16:04:29 +0000 (16:04 +0000)]
bonding: use local function pointer of bond->recv_probe in bond_handle_frame
The bond->recv_probe is called in bond_handle_frame() when
a packet is received, but bond_close() sets it to NULL. So,
a panic occurs when both functions work in parallel.
Why this happen:
After null pointer check of bond->recv_probe, an sk_buff is
duplicated and bond->recv_probe is called in bond_handle_frame.
So, a panic occurs when bond_close() is called between the
check and call of bond->recv_probe.
Patch:
This patch uses a local function pointer of bond->recv_probe
in bond_handle_frame(). So, it can avoid the null pointer
dereference.
Signed-off-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Cc: Jay Vosburgh <fubar@us.ibm.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: WANG Cong <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 11 Oct 2011 23:00:41 +0000 (23:00 +0000)]
tg3: negate USE_PHYLIB flag check
USE_PHYLIB flag in tg3_remove_one() is being checked incorrectly. This
results tg3_phy_fini->phy_disconnect is never called and when tg3 module
is removed.
In my case this resulted in panics in phy_state_machine calling function
phydev->adjust_link.
So correct this check.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Acked-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Fri, 7 Oct 2011 09:40:59 +0000 (09:40 +0000)]
bluetooth: Properly clone LSM attributes to newly created child connections
The Bluetooth stack has internal connection handlers for all of the various
Bluetooth protocols, and unfortunately, they are currently lacking the LSM
hooks found in the core network stack's connection handlers. I say
unfortunately, because this can cause problems for users who have have an
LSM enabled and are using certain Bluetooth devices. See one problem
report below:
In order to keep things simple at this point in time, this patch fixes the
problem by cloning the parent socket's LSM attributes to the newly created
child socket. If we decide we need a more elaborate LSM marking mechanism
for Bluetooth (I somewhat doubt this) we can always revisit this decision
in the future.
Reported-by: James M. Cape <jcape@ignore-your.tv> Signed-off-by: Paul Moore <pmoore@redhat.com> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Need to cleanup bridge device timers and ports when being bridge
device is being removed via netlink.
This fixes the problem of observed when doing:
ip link add br0 type bridge
ip link set dev eth1 master br0
ip link set br0 up
ip link del br0
which would cause br0 to hang in unregister_netdev because
of leftover reference count.
Reported-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Where the first one is enabling a CLOCK_PROCESS_CPUTIME_ID timer, and
the second one is keeping up-to-date.
This problem was introduced by e8abccb7193 ("posix-cpu-timers: Cure
SMP accounting oddities").
Cure the problem by removing the cputimer->lock and rq->lock nesting,
this leaves concurrent enablers doing duplicate work, but the time
wasted should be on the same order otherwise wasted spinning on the
lock and the greater-than assignment filter should ensure we preserve
monotonicity.
Reported-by: Dave Jones <davej@redhat.com> Reported-by: Simon Kirby <sim@hostway.ca> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: stable@kernel.org Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Link: http://lkml.kernel.org/r/1318928713.21167.4.camel@twins Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Daniel Suchy [Tue, 18 Oct 2011 09:09:44 +0000 (11:09 +0200)]
ALSA: HDA: conexant support for Lenovo T520/W520
This is patch for Conexant codec of Intel HDA driver, adding new quirk
for Lenovo Thinkpad T520 and W520. Conexant autodetection works fine for
T520 (similar subsystem ID is used also in W520 model) and detects more
mixer features compared to generic (fallback) Lenovo quirk with
hardcoded options in Conexant codec.
Patch was activelly tested with Linux 3.0.4, 3.0.6 and 3.0.7 without any
problems.
Takashi Iwai [Tue, 18 Oct 2011 08:44:05 +0000 (10:44 +0200)]
ALSA: hda - Add position_fix quirk for Dell Inspiron 1010
The previous fix for the position-buffer check gives yet another
regression on a Dell laptop. The safest fix right now is to add a
static quirk for this device (and better to apply it for stable
kernels too).
Matthew Daley [Fri, 14 Oct 2011 18:45:05 +0000 (18:45 +0000)]
x25: Prevent skb overreads when checking call user data
x25_find_listener does not check that the amount of call user data given
in the skb is big enough in per-socket comparisons, hence buffer
overreads may occur. Fix this by adding a check.
Signed-off-by: Matthew Daley <mattjd@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Andrew Hendry <andrew.hendry@gmail.com> Cc: stable <stable@kernel.org> Acked-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Daley [Fri, 14 Oct 2011 18:45:04 +0000 (18:45 +0000)]
x25: Handle undersized/fragmented skbs
There are multiple locations in the X.25 packet layer where a skb is
assumed to be of at least a certain size and that all its data is
currently available at skb->data. These assumptions are not checked,
hence buffer overreads may occur. Use pskb_may_pull to check these
minimal size assumptions and ensure that data is available at skb->data
when necessary, as well as use skb_copy_bits where needed.
Signed-off-by: Matthew Daley <mattjd@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Andrew Hendry <andrew.hendry@gmail.com> Cc: stable <stable@kernel.org> Acked-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Daley [Fri, 14 Oct 2011 18:45:03 +0000 (18:45 +0000)]
x25: Validate incoming call user data lengths
X.25 call user data is being copied in its entirety from incoming messages
without consideration to the size of the destination buffers, leading to
possible buffer overflows. Validate incoming call user data lengths before
these copies are performed.
It appears this issue was noticed some time ago, however nothing seemed to
come of it: see http://www.spinics.net/lists/linux-x25/msg00043.html and
commit 8db09f26f912f7c90c764806e804b558da520d4f.
Signed-off-by: Matthew Daley <mattjd@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Andrew Hendry <andrew.hendry@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Mon, 17 Oct 2011 23:07:30 +0000 (19:07 -0400)]
udplite: fast-path computation of checksum coverage
Commit 903ab86d195cca295379699299c5fc10beba31c7 of 1 March this year ("udp: Add
lockless transmit path") introduced a new fast TX path that broke the checksum
coverage computation of UDP-lite, which so far depended on up->len (only set
if the socket is locked and 0 in the fast path).
Fixed by providing both fast- and slow-path computation of checksum coverage.
The latter can be removed when UDP(-lite)v6 also uses a lockless transmit path.
Reported-by: Thomas Volkert <thomas@homer-conferencing.com> Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 17 Oct 2011 15:24:24 +0000 (08:24 -0700)]
Avoid using variable-length arrays in kernel/sys.c
The size is always valid, but variable-length arrays generate worse code
for no good reason (unless the function happens to be inlined and the
compiler sees the length for the simple constant it is).
Also, there seems to be some code generation problem on POWER, where
Henrik Bakken reports that register r28 can get corrupted under some
subtle circumstances (interrupt happening at the wrong time?). That all
indicates some seriously broken compiler issues, but since variable
length arrays are bad regardless, there's little point in trying to
chase it down.
"Just don't do that, then".
Reported-by: Henrik Grindal Bakken <henribak@cisco.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Per the text in Documentation/SubmitChecklist as below, we should
explicitly have header linux/errno.h in localtimer.h for ENXIO
reference.
1: If you use a facility then #include the file that defines/declares
that facility. Don't depend on other header files pulling in ones
that you use.
Otherwise, we may run into some compiling error like the following one,
if any file includes localtimer.h without CONFIG_LOCAL_TIMERS defined.
arch/arm/include/asm/localtimer.h: In function ‘local_timer_setup’:
arch/arm/include/asm/localtimer.h:53:10: error: ‘ENXIO’ undeclared (first use in this function)
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Mon, 3 Oct 2011 17:30:53 +0000 (18:30 +0100)]
ARM: 7117/1: perf: fix HW_CACHE_* events on Cortex-A9
Using COHERENT_LINE_{MISS,HIT} for cache misses and references
respectively is completely wrong. Instead, use the L1D events which
are a better and more useful approximation despite ignoring instruction
traffic.
Reported-by: Alasdair Grant <alasdair.grant@arm.com> Reported-by: Matt Horsnell <matt.horsnell@arm.com> Reported-by: Michael Williams <michael.williams@arm.com> Cc: stable@kernel.org Cc: Jean Pihet <j-pihet@ti.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Woodhouse [Fri, 14 Oct 2011 19:59:46 +0000 (20:59 +0100)]
intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.
We really don't want this to work in the general case; device drivers
*shouldn't* care whether they are behind an IOMMU or not. But the
integrated graphics is a special case, because the IOMMU and the GTT are
all kind of smashed into one and generally horrifically buggy, so it's
reasonable for the graphics driver to want to know when the IOMMU is
active for the graphics hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
projects / karo-tx-linux.git / log