Johannes Berg [Fri, 25 Oct 2013 10:32:51 +0000 (12:32 +0200)]
iwlwifi: warn if firmware image doesn't exist
If the firmware image that we attempt to load doesn't
actually exist we have a broken firmware file or other
code not checking things correctly, so warn in such a
case. Also avoid assigning cur_ucode/ucode_loaded then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we disassociate, mac80211 removes the station and
then, it sets the bss it unsets the assoc bool in bss_info.
Since the firwmware wants it the opposite (first set the
MAC context as unassoc, and only then, remove the STA of
the API), we have a small period of time in which the STA
in firmware doesn't have a valid ieee80211_sta pointer.
During that time, iwl_mvm_vif->ap_sta_id, is still set
to the STA in firmware that represent the AP.
Luciano Coelho [Mon, 14 Oct 2013 10:18:41 +0000 (13:18 +0300)]
iwlwifi: mvm: fix fw_rx_stats debugfs entry
The fw_rx_stats entry in debugfs was getting truncated because the
internal buffer used to hold the string was too short. The
calculation of the needed buffer size was rather bogus.
Simplify the calculation by multiplying the number of entries in the
entire structure by the size of each data line and adding the size of
the header lines.
Additionally, add the mac_id value, which was missing.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: mvm: BT Coex - always set mandatory fields
The firmware always expects the Coex Mode to be set.
Moreover, the firmware expects bit 0 is the valid bits to
be set all the times.
I misunderstood the API and didn't set these bits when
commands are sent to update the paramters of the Coex. As
a result, the firmware understood that the BT Coex was
disabled (Coex mode = 0) and ignored all the updates (valid
bit 0 clear).
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Eran Harary [Wed, 2 Oct 2013 10:53:40 +0000 (13:53 +0300)]
iwlwifi: support Signed firmware image and Dual CPUs
Support Signed firmware based on code signing system (CSS)
protocol and dual CPUs download,
the code recognize if there are more than one CPU and
if we need to operate the signed protocol according to
the ucode binary image
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: mvm: BT Coex - update integration with rate control
Remove code that is not needed and always allow MIMO when
in tight mode. In loose mode, we should avoid MIMO since BT
can use the other antenna to Rx while we Tx.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: mvm: BT Coex - track bandwidth changes in HT
BT Coex needs to be updated when the bandwidth is modified
by the AP.
While at it, remove the vif parameter from
bt_coex_vif_change since it was unused.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 6 Aug 2013 16:58:56 +0000 (18:58 +0200)]
iwlwifi: mvm: keep connection to AP after WoWLAN
Until now, after WoWLAN, we weren't able to keep the
connection to the AP because the firmware didn't give
us the right information. Since the firmware API has
been changed to include all the information we need,
change the driver to work with the new API (if it is
available) and program all the relevant information
in mac80211 to keep the connection.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: mvm: prevent the NIC to be powered at driver load time.
Some NICs aren't allowed to be powered up at driver load time.
Fix it, and move the external NVM loading from driver load time to
driver up time (parsing the external nvm file remains at driver load time).
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: pcie: restart the driver when a command times out
This should really not happen. If it does, restarting is the
only way to recover since the driver and the firmware might
very well be out of sync. Moreover, iwl_op_mode_nic_error
will print data that might help debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In loose BT Coex scheme, the aggregation size doesn't need to
be limited.
To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Gabor Juhos [Thu, 3 Oct 2013 18:00:41 +0000 (20:00 +0200)]
rt2x00: rt2800lib: fix VGC adjustment for RT3572 and RT3593
The Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022
reference driver uses different RSSI threshold
and VGC adjustment values for the RT3572 and
RT3593 chipsets.
Update the rt2800_link_tuner function to use the
same values. Also change the comment in the function
to make it more generic.
References:
RT35xx_ChipAGCAdjust function in chips/rt35xx.c
RSSI_FOR_MID_LOW_SENSIBILITY constant in include/chip/rtmp_phy.h
RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h
RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 3 Oct 2013 18:00:40 +0000 (20:00 +0200)]
rt2x00: rt2800lib: fix VGC adjustment for RT5592
In commit 3d81535ea5940446510a8a5cee1c6ad23c90c753
(rt2800: 5592: add chip specific vgc calculations)
the rt2800_link_tuner function has been modified to
adjust VGC level for the RT5592 chipset.
On the RT5592 chipset, the VGC level must be adjusted
only if rssi is greater than -65. However the current
code adjusts the VGC value by 0x10 regardless of the
actual chipset if the rssi value is between -80 and
-65.
Fix the broken behaviour by reordering the if-else
statements.
Cc: stable@vger.kernel.org Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pausing queue on flush make no sense since txdone procedure un-pause
queue. Before flush procedure we have to assure queue is stopped,
i.e. on receive path h/w RX is disabled, on transmit path queue is
disabled in mac80211. That conditions are true except one function:
rt2x00usb_watchdog_tx_dma(), so add stop/start queue there.
Note stop/start queue can be racy if we do this from multiple paths,
but currently we stop TX queues only on rt2x00lib_disable_radio(),
which also stop/sync watchdog, hance we have no race condition.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 4 Oct 2013 20:07:09 +0000 (22:07 +0200)]
rt2x00: rt2800lib: fix default VGC values for RT3572 for the 5GHz band
The rt2x00 driver uses 0x22 as a default VGC value
in VGC adjustment for the RT3572 chipset. In the
Ralink DPO_RT5572_LinuxSTA_2.6.1.3_20121022 driver,
this value is only used for initialization. During
VGC adjustment, the reference driver uses different
values.
Update the 'rt2800_get_default_vgc' function to
synchronize the values with the reference driver.
Also add the missing AGC initialization code into
the 'rt2800_config_channel' function.
References:
RT35xx_SetAGCInitValue in chip/rt35xx.c
RT35xx_ChipAGCAdjust in chip/rt35xx.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 3 Oct 2013 18:00:43 +0000 (20:00 +0200)]
rt2x00: rt2800lib: fix VGC programming for RT3572 and RT3593
According to the DPO_RT5572_LinuxSTA_2.6.1.3_20121022
reference driver, programming of the 'BBP 66' register
on the RT3572 and RT3593 chipsets must be done via the
'rt2800_bbp_write_with_rx_chain' function. This ensures
that value is correclty set for all RX chains.
References:
RT35xx_ChipAGCAdjust and RT35xx_SetAGCInitValue functions
in chips/rt35xx.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 3 Oct 2013 18:00:42 +0000 (20:00 +0200)]
rt2x00: rt2800lib: fix default VGC values for RT3593
Update the rt2800_get_default_vgc function to use the same VGC
values that the DPO_RT5572_LinuxSTA_2.6.1.3_20121022 reference
driver uses.
References:
RT35xx_ChipAGCAdjust in chips/rt35xx.c
RT3593_R66_MID_LOW_SENS_GET macro in include/chip/rt3593.h
RT3593_R66_NON_MID_LOW_SEMS_GET macro in include/chips/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 3 Oct 2013 12:07:02 +0000 (14:07 +0200)]
rt2x00: rt2800lib: remove TXPOWER_DELTA entry from extended EEPROM map
The TXPOWER_DELTA field of the regular EEPROM
stores the TX power compensation value for HT40.
The extended EEPROM has no such field, it stores
separate TX power values for HT20 and for HT40.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Paul Menzel <paulepanter@users.sourceforge.net> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 3 Oct 2013 12:07:01 +0000 (14:07 +0200)]
rt2x00: rt2800lib: remove TXMIXER_GAIN entries from the extended EEPROM map
The comments are indicating that the TXMIXER_GAIN_BG
and TXMIXED_GAIN_A entries are overlapping with the
RSSI_BG2 and RSSI_A2 entries in the extended EEPROM
map. This is not correct, because the upper byte of
the RSSI_BG2 and RSSI_A2 entries are reserved. There
are no TX mixer gain values are stored at all in the
extended EEPROM.
Remove the initialization of these entries from the
extended EEPROM map to reflect this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Paul Menzel <paulepanter@users.sourceforge.net> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Thu, 3 Oct 2013 11:49:11 +0000 (13:49 +0200)]
brcmsmac: add support for a BCM4313 with PCI id 0x4313
There are some BCM4313 out there with a PCI id of 0x4313. These devices
are missing a sprom and are only used on routers or other embedded
devices. We found one connected to a BCM63XX SoC.
This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Thu, 3 Oct 2013 11:49:10 +0000 (13:49 +0200)]
bcma: add PCI id 0x4313
This PCI id is used by some BCM4313 cards without a sprom. I have seen
such a card on a router connected to some BCM63XX SoC via PCIe. There
are cards out there with the same PCI id and a BCM4311, which is a pre
ieee80211n chip only supporting ieee80211a, these are still not
supported by b43 and not detected by ssb.
This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Thu, 3 Oct 2013 11:49:09 +0000 (13:49 +0200)]
bcma: reject PCI cards in bcma.
bcma currently only supports PCIe cards and no PCI cards, reject them
if we find them. I have never heard of any PCI card using the AI bus
(bcma), all of them are using ssb instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
So, pass the right name. rt2x00_ops->name contains KBUILD_MODNAME
and good for that, so pass it.
Handler names will be "rt2500pci", "rt2500pci" etc.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru> CC: Ivo van Doorn <IvDoorn@gmail.com> CC: Gertjan van Wingerde <gwingerde@gmail.com> CC: Helmut Schaa <helmut.schaa@googlemail.com> CC: linux-wireless@vger.kernel.org Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So
far WCN3660/WCN3680 is available only on MSM platform.
Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS
Wiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xx
A lot people made a contribution to this driver. Here is the list in
alphabetical order:
Eugene Krasnikov <k.eugene.e@gmail.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Olof Johansson <dev@skyshaper.net>
Pontus Fuchs <pontus.fuchs@gmail.com>
Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variables cancel_scan_cmd, enable_data, hs_activate and valid are
only assigned the values true and false. Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
0411,0241 RT5572 BUFFALO WI-U2-300D Wireless LAN Adapter
0789,0170 RT3572 Logitec LAN-W300AN/U2
0846,9013 RT3573 NETGEAR Adaptador USB Inalambrico Movistar
0df6,006e RT3573 Sitecom WiFi USB adapter N900
2001,3c1f RT3573 D-Link DWA-162 Wireless N900 Dual Band Adapter
2001,3c20 RT5372 D-Link DWA-140 Wireless N USB Adapter(rev.D)
2001,3c21 RT5572 D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C)
2001,3c22 RT5372 D-Link DWA-132 Wireless N USB Adapter(rev.B)
2001,3c23 RT5372 D-Link GO-USB-N300 Wireless N Easy USB Adapter
2019,ab29 ? Planex GW-USMirco300
20f4,724a RT5572 TRENDnet N600 Wireless Dual Band USB Adapter
Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 26 Sep 2013 18:25:33 +0000 (13:25 -0500)]
rtlwifi: rtl8188ee: Convert driver to use new rtl_phy_scan_operation_backup() routine
Now that rtl_phy_scan_operation_backup() exists, convert rtl8188ee to use it.
Routine rtl88e_phy_scan_operation_backup() is no longer used and is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 26 Sep 2013 18:25:32 +0000 (13:25 -0500)]
rtlwifi: rtl8723ae: Convert driver to use new rtl_phy_scan_operation_backup() routine
Now that rtl_phy_scan_operation_backup() exists, convert rtl8723ae to use it.
Routine rtl8723ae_phy_scan_operation_backup() is no longer used and is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 26 Sep 2013 18:25:31 +0000 (13:25 -0500)]
rtlwifi: rtl8192ce: Convert driver to use new rtl_phy_scan_operation_backup() routine
Now that rtl_phy_scan_operation_backup() exists, convert rtl8192de to use it.
Routine rtl92d_phy_scan_operation_backup() is no longer used and is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 26 Sep 2013 18:25:27 +0000 (13:25 -0500)]
rtlwifi: Implement a common rtl_phy_scan_operation_backup() routine
Several of the drivers supported by rtlwifi individually implement the same
routine that supports scans. As a first step, create this routine in
driver rtlwifi.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This info message is the result of a real error due to a missing break statement
in a "while (1)" loop.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.10+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable 'stats.noise' is not used, thus the initializers are removed.
The unreachable code info is fixed by including the appropriate section inside
#ifdef .. #endif constructions.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for new RF chip ID: 3070. It seems to be the same as 5370,
maybe vendor just put wrong value on the eeprom, but add this id anyway
since devices with it showed on the marked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: Use fw filename and nvram based of devid for sdio.
SDIO firmware download routines uses one name for firmware file
and nvram file for all sdio devices. This is not user friendly.
Use fw filename and nvram filename based upon chip id and revision.
Reported-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The definition of BRCMF_EVENTING_MASK_LEN results in a sparse
error message
.../fweh.c:331:22: error: bad constant expression
.../fweh.c:388:22: error: bad constant expression
.../dhd_common.c:256:22: error: bad constant expression
This is caused by the use of roundup() in BRCMF_EVENTING_MASK_LEN
and it is used to allocate an array variable on the stack. Better
use DIV_ROUND_UP() macro.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 25 Sep 2013 11:05:43 +0000 (13:05 +0200)]
brcmfmac: reserve memory for bus layer in sk_buff::cb
Bus layer need to share sk_buff::cb with firmware signal feature. Reserve
necessary memory so they won't overwrite each other.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 25 Sep 2013 11:05:40 +0000 (13:05 +0200)]
brcmfmac: sync firmware event list
Update event list to keep sync with firmware development. Use calculated event
mask length instead of hard-coded value.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marcel Holtmann [Thu, 3 Oct 2013 08:26:37 +0000 (01:26 -0700)]
Bluetooth: Only one command per L2CAP LE signalling is supported
The Bluetooth specification makes it clear that only one command
should be present in the L2CAP LE signalling packet. So tighten
the checks here and restrict it to exactly one command.
This is different from L2CAP BR/EDR signalling where multiple
commands can be part of the same packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 06:37:29 +0000 (23:37 -0700)]
Bluetooth: Allow changing device class when BR/EDR is disabled
Changing the device class when BR/EDR is disabled has no visible
effect for remote devices. However to simplify the logic allow it
as long as the controller supports BR/EDR operations.
If it is not allowed, then the overall logic becomes rather
complicated since the class of device values would need clearing
or restoring when BR/EDR setting changes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 04:16:08 +0000 (21:16 -0700)]
Bluetooth: Restrict loading of long term keys to LE capable controllers
Loading long term keys into a BR/EDR only controller make no sense.
The kernel would never use any of these keys. So instead of allowing
userspace to waste memory, reject such operation with a not supported
error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 04:16:07 +0000 (21:16 -0700)]
Bluetooth: Restrict loading of link keys to BR/EDR capable controllers
Loading link keys into a LE only controller make no sense. The kernel
would never use any of these keys. So instead of allowing userspace
to waste memory, reject such operation with a not supported error
message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 05:10:32 +0000 (22:10 -0700)]
Bluetooth: Allow setting static address even if LE is disabled
Setting the static address does not depend on LE beeing enabled. It
only depends on a controller with LE support.
When depending on LE enabled this command becomes really complicated
since in case LE gets disabled, it would be required to clear the
static address and also its random address representation inside
the controller. With future support for private addresses such
complex setup should be avoided.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 04:31:52 +0000 (21:31 -0700)]
Bluetooth: Restrict SSP setting changes to BR/EDR enabled controllers
Only when BR/EDR is supported and enabled, allow changing of the SSP
setting. Just checking if the hardware supports SSP is not enough
since it might be the case that BR/EDR is disabled.
In the case that BR/EDR is disabled, but SSP supported by the
controller the not supported error message is now returned.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 2 Oct 2013 15:28:21 +0000 (08:28 -0700)]
Bluetooth: Fix memory leak with L2CAP signal channels
The wrong type of L2CAP signalling packets on the wrong type of
either BR/EDR or LE links need to be dropped. When that happens
the packet is dropped, but the memory not freed. So actually
free the memory as well.
DoHyun Pyun [Wed, 2 Oct 2013 12:54:53 +0000 (21:54 +0900)]
Bluetooth: Add the definition for Slave Page Response Timeout
The Slave Page Response Timeout event indicates to the Host that a
slave page response timeout has occurred in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 110
"7.7.72 Slave Page Response Timeout Event [New Section]
...
Note: this event will be generated if the slave BR/EDR Controller
responds to a page but does not receive the master FHS packet
(see Baseband, Section 8.3.3) within pagerespTO.
Event Parameters: NONE"
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Status 0x00 Start Synchronization Train command completed
successfully.
0x01-0xFF Start Synchronization Train command failed.
See Part D, Error Codes, for error codes and
descriptions."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:51 +0000 (21:54 +0900)]
Bluetooth: Add the definition for Start Synchronization Train
The Start_Synchronization_Train command controls the Synchronization
Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 86
"7.1.51 Start Synchronization Train Command [New Section]
...
If connectionless slave broadcast mode is not enabled, the Command
Disallowed (0x0C) error code shall be returned. After receiving this
command and returning a Command Status event, the Baseband starts
attempting to send synchronization train packets containing information
related to the enabled Connectionless Slave Broadcast packet timing.
Note: The AFH_Channel_Map used in the synchronization train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
The synchronization train packets will be sent using the parameters
specified by the latest Write_Synchronization_Train_Parameters command.
The Synchronization Train will continue until synchronization_trainTO
slots (as specified in the last Write_Synchronization_Train command)
have passed or until the Host disables the Connectionless Slave Broadcast
logical transport."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:50 +0000 (21:54 +0900)]
Bluetooth: Add the definition and structure for Set CSB
he Set_Connectionless_Slave_Broadcast command controls the
Connectionless Slave Broadcast functionality in the BR/EDR
Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 78
"7.1.49 Set Connectionless Slave Broadcast Command [New Section]
...
The LT_ADDR indicated in the Set_Connectionless_Slave_Broadcast shall be
pre-allocated using the HCI_Set_Reserved_LT_ADDR command. If the
LT_ADDR has not been reserved, the Unknown Connection Identifier (0x02)
error code shall be returned. If the controller is unable to reserve
sufficient bandwidth for the requested activity, the Connection Rejected
Due to Limited Resources (0x0D) error code shall be returned.
The LPO_Allowed parameter informs the BR/EDR Controller whether it is
allowed to sleep.
The Packet_Type parameter specifies which packet types are allowed. The
Host shall either enable BR packet types only, or shall enable EDR and DM1
packet types only.
The Interval_Min and Interval_Max parameters specify the range from which
the BR/EDR Controller must select the Connectionless Slave Broadcast
Interval. The selected Interval is returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:49 +0000 (21:54 +0900)]
Bluetooth: Add the structure for Write Sync Train Parameters
The Write_Synchronization_Train_Parameters command configures
the Synchronization Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 97
"7.3.90 Write Synchronization Train Parameters Command [New Section]
...
Note: The AFH_Channel_Map used in the Synchronization Train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
Interval_Min and Interval_Max specify the allowed range of
Sync_Train_Interval. Refer to [Vol. 2], Part B, section 2.7.2 for
a detailed description of Sync_Train_Interval. The BR/EDR Controller shall
select an interval from this range and return it in Sync_Train_Interval.
If the Controller is unable to select a value from this range, it shall
return the Invalid HCI Command Parameters (0x12) error code.
Once started (via the Start_Synchronization_Train Command) the
Synchronization Train will continue until synchronization_trainTO slots have
passed or Connectionless Slave Broadcast has been disabled."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:48 +0000 (21:54 +0900)]
Bluetooth: Add the definition and structure for Set CSB Data
The Set_Connectionless_Slave_Broadcast_Data command provides the
ability for the Host to set Connectionless Slave Broadcast data in
the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 93
"7.3.88 Set Connectionless Slave Broadcast Data Command [New Section]
...
If connectionless slave broadcast mode is disabled, this data shall be
kept by the BR/EDR Controller and used once connectionless slave broadcast
mode is enabled. If connectionless slave broadcast mode is enabled,
and this command is successful, this data will be sent starting with
the next Connectionless Slave Broadcast instant.
The Data_Length field may be zero, in which case no data needs to be
provided.
The Host may fragment the data using the Fragment field in the command. If
the combined length of the fragments exceeds the capacity of the largest
allowed packet size specified in the Set Connectionless Slave Broadcast
command, all fragments associated with the data being assembled shall be
discarded and the Invalid HCI Command Parameters error (0x12) shall be
returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:47 +0000 (21:54 +0900)]
Bluetooth: Add the definition and structure for Delete Reserved LT_ADDR
The Delete_Reserved_LT_ADDR command requests that the BR/EDR
Controller cancel the reservation for a specific LT_ADDR reserved for the
purposes of Connectionless Slave Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 92
"7.3.87 Delete Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is not reserved by the
BR/EDR Controller, it shall return the Unknown Connection Identifier (0x02)
error code.
If connectionless slave broadcast mode is still active, then the Controller
shall return the Command Disallowed (0x0C) error code."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:46 +0000 (21:54 +0900)]
Bluetooth: Add the definition and structure for Set Reserved LT_ADDR
The Set_Reserved_LT_ADDR command allows the host to request that the
BR/EDR Controller reserve a specific LT_ADDR for Connectionless Slave
Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 90
"7.3.86 Set Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is already in use by the
BR/EDR Controller, it shall return the ACL Connection Already Exists (0x0B)
error code. If the LT_ADDR indicated in the LT_ADDR parameter is out of
range, the controller shall return the Invalid HCI Command Parameters (0x12)
error code. If the command succeeds, then the reserved LT_ADDR shall be
used when issuing subsequent Set Connectionless Slave Broadcast Data and
Set Connectionless Slave Broadcast commands.
To ensure that the reserved LT_ADDR is not already allocated, it is
recommended that this command be issued at some point after HCI_Reset is
issued but before page scanning is enabled or paging is initiated."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: mvm: change the name of init_ucode_run flag
In RF KILL the init ucode is running, but don't complete
all its tasks, so we need to run the init ucode again.
Change the flag name to init_ucode_complete, to be more appropriate.
Johannes Berg [Tue, 20 Aug 2013 11:04:10 +0000 (13:04 +0200)]
iwlwifi: mvm: implement new IPv6 offload API
The firmware API for IPv6 NDP/NS offload has changed again.
Implement support for the new API; this requires calculating
the solicited node address for each "target" address as it's
no longer ignored by the firmware.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / linux-beck.git / log