ARM: imx: let L2 initialization be a common function
Move imx6q L2 initialization function imx6q_init_l2cache() into
system.c, and rename it imx_init_l2cache(), so that other platforms
other than imx6q can also use the function.
Sascha Hauer [Thu, 20 Jun 2013 15:34:31 +0000 (17:34 +0200)]
ARM: i.MX6: call ksz9021 phy fixup for all i.MX6 boards
In current U-Boot the sabrelite, nitrogen6x and titanium all need
the same fixup for the ksz9021 phy. Instead of limiting the fixup
to a single board apply them for all.
The fec/enet driver calculates MDC rate with the formula below.
ref_freq / ((MII_SPEED + 1) x 2)
The ref_freq here is the fec internal module clock, which is missing
from clk-vf610 clock driver right now. And clk-vf610 driver mistakenly
supplies RMII clock (50 MHz) as the source to fec. This results in the
situation that fec driver gets ref_freq as 50 MHz, while physically it
runs at 66 MHz (fec module clock physically sources from ipg which runs
at 66 MHz). That's why software expects MDC runs at 2.5 MHz, while the
measurement tells it runs at 3.3 MHz. And this causes the PHY KSZ8041
keeps swithing between Full and Half mode as below.
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
Add the missing module clock for ENET0 and ENET1, and correct the clock
supplying in device tree to fix above issue.
Thanks to Alison Wang <b18965@freescale.com> for debugging the issue.
These systems all use saif0 as the mclock provider to codec sgtl5000.
Reflect that in device tree source, so that sgtl5000 can find the clock
by calling clk_get().
Philipp Zabel [Fri, 21 Jun 2013 13:36:11 +0000 (15:36 +0200)]
ARM i.MX53: Fix UART pad configuration
The current default pad configuration for UART RX and TX pads sets a 360k
pull-down and writes 1 to a reserved bit (1 << 0). It doesn't seem right to
me that in idle state, the UART has to keep the signal high against a
pull-down resistor.
This patch instead sets a 100k pull-up, which incidentally corresponds to the
register reset value for all but one (MX53_PAD_KEY_ROW0__UART4_RXD_MUX) pad,
and removes the write to the reserved bit.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Merge branch 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
Pull slab update from Pekka Enberg:
"Highlights:
- Fix for boot-time problems on some architectures due to
init_lock_keys() not respecting kmalloc_caches boundaries
(Christoph Lameter)
- CONFIG_SLUB_CPU_PARTIAL requested by RT folks (Joonsoo Kim)
- Fix for excessive slab freelist draining (Wanpeng Li)
- SLUB and SLOB cleanups and fixes (various people)"
I ended up editing the branch, and this avoids two commits at the end
that were immediately reverted, and I instead just applied the oneliner
fix in between myself.
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
slub: Check for page NULL before doing the node_match check
mm/slab: Give s_next and s_stop slab-specific names
slob: Check for NULL pointer before calling ctor()
slub: Make cpu partial slab support configurable
slab: add kmalloc() to kernel API documentation
slab: fix init_lock_keys
slob: use DIV_ROUND_UP where possible
slub: do not put a slab to cpu partial list when cpu_partial is 0
mm/slub: Use node_nr_slabs and node_nr_objs in get_slabinfo
mm/slub: Drop unnecessary nr_partials
mm/slab: Fix /proc/slabinfo unwriteable for slab
mm/slab: Sharing s_next and s_stop between slab and slub
mm/slab: Fix drain freelist excessively
slob: Rework #ifdeffery in slab.h
mm, slab: moved kmem_cache_alloc_node comment to correct place
Now, this uses SLUB pretty much unmodified, but as it is the -rt kernel
with CONFIG_PREEMPT_RT set, spinlocks are mutexes, although they do
disable migration. But the SLUB code is relatively lockless, and the
spin_locks there are raw_spin_locks (not converted to mutexes), thus I
believe this bug can happen in mainline without -rt features. The -rt
patch is just good at triggering mainline bugs ;-)
Anyway, looking at where this crashed, it seems that the page variable
can be NULL when passed to the node_match() function (which does not
check if it is NULL). When this happens we get the above panic.
As page is only used in slab_alloc() to check if the node matches, if
it's NULL I'm assuming that we can say it doesn't and call the
__slab_alloc() code. Is this a correct assumption?
Acked-by: Christoph Lameter <cl@linux.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more vfs stuff from Al Viro:
"O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
making simple_lookup() usable for filesystems with non-NULL s_d_op,
which allows us to get rid of quite a bit of ugliness"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
sunrpc: now we can just set ->s_d_op
cgroup: we can use simple_lookup() now
efivarfs: we can use simple_lookup() now
make simple_lookup() usable for filesystems that set ->s_d_op
configfs: don't open-code d_alloc_name()
__rpc_lookup_create_exclusive: pass string instead of qstr
rpc_create_*_dir: don't bother with qstr
llist: llist_add() can use llist_add_batch()
llist: fix/simplify llist_add() and llist_add_batch()
fput: turn "list_head delayed_fput_list" into llist_head
fs/file_table.c:fput(): add comment
Safer ABI for O_TMPFILE
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"Nothing overly exciting here - a couple of new drivers that don't do a
great deal, along with some miscellaneous fixes and a couple of small
feature enablement patches"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
x86 platform drivers: fix gpio leak
toshiba_acpi: Add dependency on SERIO_I8042
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. 1015E/U
Add trivial driver to disable Intel Smart Connect
Add support driver for Intel Rapid Start Technology
hp-wmi: add supports for POST code error
asus-wmi: control wlan-led only if wapf == 4
drivers/platform/x86/intel_ips: Convert to module_pci_driver
asus-nb-wmi: ignore ALS notification key code
asus-wmi: append newline to messages
x86: asus-laptop: fix invalid point access
x86: msi-laptop: fix memleak
amilo-rfkill: Add dependency on SERIO_I8042
dell-laptop: fix error return code in dell_init()
hp-wmi: Enable hotkeys on some systems
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
"An update to Elantech driver to support hardware v7, fix to the new
cyttsp4 driver to use proper addressing, ads7846 device tree support
and nspire-keypad got a small cleanup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: nspire-keypad - replace magic offset with define
Input: elantech - fix for newer hardware versions (v7)
Input: cyttsp4 - use 16bit address for I2C/SPI communication
Input: ads7846 - add device tree bindings
Input: ads7846 - make sure we do not change platform data
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"This is the remaining set of SCSI patches for the merge window. It's
mostly driver updates (scsi_debug, qla2xxx, storvsc, mp3sas). There
are also several bug fixes in fcoe, libfc, and megaraid_sas. We also
have a couple of core changes to try to make device destruction more
deterministic"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
[SCSI] scsi constants: command, sense key + additional sense strings
fcoe: Reduce number of sparse warnings
fcoe: Stop fc_rport_priv structure leak
libfcoe: Fix meaningless log statement
libfc: Differentiate echange timer cancellation debug statements
libfc: Remove extra space in fc_exch_timer_cancel definition
fcoe: fix the link error status block sparse warnings
fcoe: Fix smatch warning in fcoe_fdmi_info function
libfc: Reject PLOGI from nodes with incompatible role
[SCSI] enable destruction of blocked devices which fail LUN scanning
[SCSI] Fix race between starved list and device removal
[SCSI] megaraid_sas: fix a bug for 64 bit arches
[SCSI] scsi_debug: reduce duplication between prot_verify_read and prot_verify_write
[SCSI] scsi_debug: simplify offset calculation for dif_storep
[SCSI] scsi_debug: invalidate protection info for unmapped region
[SCSI] scsi_debug: fix NULL pointer dereference with parameters dif=0 dix=1
[SCSI] scsi_debug: fix incorrectly nested kmap_atomic()
[SCSI] scsi_debug: fix invalid address passed to kunmap_atomic()
[SCSI] mpt3sas: Bump driver version to v02.100.00.00
[SCSI] mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed
...
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
- core fix for missing round up in the generic irq chip implementation
- new irq chip for MOXA SoCs
- a few fixes and cleanups in the irqchip drivers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for MOXA ART SoCs
genirq: generic chip: Use DIV_ROUND_UP to calculate numchips
irqchip: nvic: Fix wrong num_ct argument for irq_alloc_domain_generic_chips()
irqchip: sun4i: Staticize sun4i_irq_ack()
irqchip: vt8500: Staticize local symbols
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
- watchdog fixes for full dynticks
- improved debug output for full dynticks
- remove an obsolete full dynticks check
- two ARM SoC clocksource drivers for sharing across SoCs
- tick broadcast fix for CPU hotplug
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: broadcast: Check broadcast mode on CPU hotplug
clocksource: arm_global_timer: Add ARM global timer support
clocksource: Add Marvell Orion SoC timer
nohz: Remove obsolete check for full dynticks CPUs to be RCU nocbs
watchdog: Boot-disable by default on full dynticks
watchdog: Rename confusing state variable
watchdog: Register / unregister watchdog kthreads on sysctl control
nohz: Warn if the machine can not perform nohz_full
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"A few fixes for ARM, mostly just one liners with the exception of the
missing section specification. We decided not to rely on .previous to
fix this but to explicitly state the section we want the code to be
in."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7778/1: smp_twd: twd_update_frequency need be run on all online CPUs
ARM: 7782/1: Kconfig: Let ARM_ERRATA_364296 not depend on CONFIG_SMP
ARM: mm: fix boot on SA1110 Assabet
ARM: 7781/1: mmu: Add debug_ll_io_init() mappings to early mappings
ARM: 7780/1: add missing linker section markup to head-common.S
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull watchdog updates from Wim Van Sebroeck:
- lots of devm_ conversions and cleanup
- platform_set_drvdata cleanups
- s3c2410: dev_err/dev_info + dev_pm_ops
- watchdog_core: don't try to stop device if not running fix
- wdrtas: use print_hex_dump
- xilinx cleanups
- orion_wdt fixes
- softdog cleanup
- hpwdt: check on UEFI bits
- deletion of mpcore_wdt driver
- addition of broadcom BCM2835 watchdog timer driver
- addition of MEN A21 watcdog devices
* git://www.linux-watchdog.org/linux-watchdog: (38 commits)
watchdog: hpwdt: Add check for UEFI bits
watchdog: softdog: remove replaceable ping operation
watchdog: New watchdog driver for MEN A21 watchdogs
Watchdog: fix clearing of the watchdog interrupt
Watchdog: allow orion_wdt to be built for Dove
watchdog: Add Broadcom BCM2835 watchdog timer driver
watchdog: delete mpcore_wdt driver
watchdog: xilinx: Setup the origin compatible string
watchdog: xilinx: Fix driver header
watchdog: wdrtas: don't use custom version of print_hex_dump
watchdog: core: don't try to stop device if not running
watchdog: jz4740: Pass device to clk_get
watchdog: twl4030: Remove redundant platform_set_drvdata()
watchdog: mpcore: Remove redundant platform_set_drvdata()
watchdog: da9055: use platform_{get,set}_drvdata()
watchdog: da9052: use platform_{get,set}_drvdata()
watchdog: cpwd: use platform_{get,set}_drvdata()
watchdog: s3c2410_wdt: convert s3c2410wdt to dev_pm_ops
watchdog: s3c2410_wdt: use dev_err()/dev_info() instead of pr_err()/pr_info()
watchdog: wm831x: use platform_{get,set}_drvdata()
...
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- AF_IB (native IB addressing) for CMA from Sean Hefty
- new mlx5 driver for Mellanox Connect-IB adapters (including post
merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- other small changes and fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
mlx5: Return -EFAULT instead of -EPERM
IB/qib: Log all SDMA errors unconditionally
IB/qib: Fix module-level leak
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
IB/uverbs: Use get_unused_fd_flags(O_CLOEXEC) instead of get_unused_fd()
mlx5_core: Fixes for sparse warnings
IB/mlx5: Make profile[] static in main.c
mlx5: Fix parameter type of health_handler_t
mlx5: Add driver for Mellanox Connect-IB adapters
IB/core: Add reserved values to enums for low-level driver use
IB/srp: Bump driver version and release date
IB/srp: Make HCA completion vector configurable
IB/srp: Maintain a single connection per I_T nexus
IB/srp: Fail I/O fast if target offline
IB/srp: Skip host settle delay
IB/srp: Avoid skipping srp_reset_host() after a transport error
IB/srp: Fix remove_one crash due to resource exhaustion
IB/qib: New transmitter tunning settings for Dell 1.1 backplane
IB/core: Fix error return code in add_port()
...
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
Merge tag 'for-linus-v3.11-rc1-2' of git://oss.sgi.com/xfs/xfs
Pull more xfs updates from Ben Myers:
"Here are a fix for xfs_fsr, a cleanup in bulkstat, a cleanup in
xfs_open_by_handle, updated mount options documentation, a cleanup in
xfs_bmapi_write, a fix for the size of dquot log reservations, a fix
for sgid inheritance when acls are in use, a fix for cleaning up
quotainfo structures, and some more of the work which allows group and
project quotas to be used together.
We had a few more in this last quota category that we might have liked
to get in, but it looks there are still a few items that need to be
addressed.
- fix for xfs_fsr returning -EINVAL
- cleanup in xfs_bulkstat
- cleanup in xfs_open_by_handle
- update mount options documentation
- clean up local format handling in xfs_bmapi_write
- fix dquot log reservations which were too small
- fix sgid inheritance for subdirectories when default acls are in use
- add project quota fields to various structures
- fix teardown of quotainfo structures when quotas are turned off"
* tag 'for-linus-v3.11-rc1-2' of git://oss.sgi.com/xfs/xfs:
xfs: Fix the logic check for all quotas being turned off
xfs: Add pquota fields where gquota is used.
xfs: fix sgid inheritance for subdirectories inheriting default acls [V3]
xfs: dquot log reservations are too small
xfs: remove local fork format handling from xfs_bmapi_write()
xfs: update mount options documentation
xfs: use get_unused_fd_flags(0) instead of get_unused_fd()
xfs: clean up unused codes at xfs_bulkstat()
xfs: use XFS_BMAP_BMDR_SPACE vs. XFS_BROOT_SIZE_ADJ
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Fixes for 4 cifs bugs, including a reconnect problem, a problem
parsing responses to SMB2 open request, and setting nlink incorrectly
to some servers which don't report it properly on the wire. Also
improves data integrity on reconnect with series from Pavel which adds
durable handle support for SMB2."
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix a deadlock when a file is reopened
CIFS: Reopen the file if reconnect durable handle failed
[CIFS] Fix minor endian error in durable handle patch series
CIFS: Reconnect durable handles for SMB2
CIFS: Make SMB2_open use cifs_open_parms struct
CIFS: Introduce cifs_open_parms struct
CIFS: Request durable open for SMB2 opens
CIFS: Simplify SMB2 create context handling
CIFS: Simplify SMB2_open code path
CIFS: Respect create_options in smb2_open_file
CIFS: Fix lease context buffer parsing
[CIFS] use sensible file nlink values if unprovided
Limit allocation of crypto mechanisms to dialect which requires
llist_add(new, head) can simply use llist_add_batch(new, new, head),
no need to duplicate the code.
This obviously uninlines llist_add() and to me this is a win. But we
can make llist_add_batch() inline if this is desirable, in this case
gcc can notice that new_first == new_last if the caller is llist_add().
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Vagin <avagin@openvz.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: David Howells <dhowells@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
llist: fix/simplify llist_add() and llist_add_batch()
1. This is mostly theoretical, but llist_add*() need ACCESS_ONCE().
Otherwise it is not guaranteed that the first cmpxchg() uses the
same value for old_entry and new_last->next.
2. These helpers cache the result of cmpxchg() and read the initial
value of head->first before the main loop. I do not think this
makes sense. In the likely case cmpxchg() succeeds, otherwise
it doesn't hurt to reload head->first.
I think it would be better to simplify the code and simply read
->first before cmpxchg().
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Vagin <avagin@openvz.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: David Howells <dhowells@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 13 Jul 2013 09:26:37 +0000 (13:26 +0400)]
Safer ABI for O_TMPFILE
[suggested by Rasmus Villemoes] make O_DIRECTORY | O_RDWR part of O_TMPFILE;
that will fail on old kernels in a lot more cases than what I came up with.
And make sure O_CREAT doesn't get there...
James Bottomley [Sat, 13 Jul 2013 04:22:56 +0000 (08:22 +0400)]
Merge tag 'fcoe' into for-linus
A short series of fixes to libfc, libfcoe and fcoe.
Most patches fix formatting problems, one changes
the behavior of which discovered ports can/will be
logged into and another fixes a memory leak.
ipv6: only static routes qualify for equal cost multipathing
Static routes in this case are non-expiring routes which did not get
configured by autoconf or by icmpv6 redirects.
To make sure we actually get an ecmp route while searching for the first
one in this fib6_node's leafs, also make sure it matches the ecmp route
assumptions.
v2:
a) Removed RTF_EXPIRE check in dst.from chain. The check of RTF_ADDRCONF
already ensures that this route, even if added again without
RTF_EXPIRES (in case of a RA announcement with infinite timeout),
does not cause the rt6i_nsiblings logic to go wrong if a later RA
updates the expiration time later.
v3:
a) Allow RTF_EXPIRES routes to enter the ecmp route set. We have to do so,
because an pmtu event could update the RTF_EXPIRES flag and we would
not count this route, if another route joins this set. We now filter
only for RTF_GATEWAY|RTF_ADDRCONF|RTF_DYNAMIC, which are flags that
don't get changed after rt6_info construction.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Usual problem with the usual fix, add the appropriate calls to dma_mapping_error
where appropriate
Untested, as I don't have hardware, but its pretty straightforward
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: David S. Miller <davem@davemloft.net> CC: Roger Luethi <rl@hellgate.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The usual straighforward failure to check for dma_mapping_error after a map
operation is completed.
This patch should fix it, the reporter wandered off after filing this bz:
https://bugzilla.redhat.com/show_bug.cgi?id=954170
and I don't have hardware to test, but the fix is pretty straightforward, so I
figured I'd post it for review.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Jay Cliburn <jcliburn@gmail.com> CC: Chris Snook <chris.snook@gmail.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Change snmp RETRANSFAILS stat to include timeout retransmit failures
in addition to other loss recoveries.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
>> drivers/net/usb/r815x.c:38:16: sparse: cast to restricted __le32
>> drivers/net/usb/r815x.c:67:15: sparse: cast to restricted __le32
>> drivers/net/usb/r815x.c:69:13: sparse: incorrect type in assignment (different base types)
drivers/net/usb/r815x.c:69:13: expected unsigned int [unsigned] [addressable] [assigned] [usertype] tmp
drivers/net/usb/r815x.c:69:13: got restricted __le32 [usertype] <noident>
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Spotted-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
config: make ARCH=avr32 allyesconfig
drivers/net/usb/r8152.c: In function 'rtl8152_start_xmit':
drivers/net/usb/r8152.c:956: warning: integer overflow in expression
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Spotted-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Fri, 12 Jul 2013 18:06:01 +0000 (11:06 -0700)]
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij:
Ux500 defconfig changes:
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable HIGHMEM in the u8500 defconfig
ARM: ux500: Update MMC configs for u8500 defconfig
ARM: ux500: select SND_SOC_UX500 for ux500
ARM: ux500: update defconfig base
ARM: ux500: select WATCHDOG and MUSB for ux500
arm: multi_v7_defconfig: add i.MX options and NFS root
- Add i.MX serial console support. This gives us the boot messages on
UART on e.g. the i.MX6Q sabre sd platform.
- Add the necessary config options, to allow booting with NFS root on
an i.MX6 sabre sd.
- Add Freescale LPUART serial console support. This gives us the boot
messages on UART on e.g. the Vybrid VF610 Tower board.
Olof Johansson [Fri, 12 Jul 2013 17:59:39 +0000 (10:59 -0700)]
Merge tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes and minor defconfig updates that would be good to
get in before -rc1.
* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
ARM: scu: provide inline dummy functions when SCU is not present
ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
ARM: OMAP2+: timer: initialize before using oh_name
Signed-off-by: Olof Johansson <olof@lixom.net>
Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.
Dave Hansen [Mon, 8 Jul 2013 21:44:04 +0000 (14:44 -0700)]
perf/x86: Fix incorrect use of do_div() in NMI warning
I completely botched understanding the calling conventions of
do_div(). I assumed that do_div() returned the result instead
of realizing that it modifies its argument and returns a
remainder. The side-effect from this would be bogus numbers
for the "msecs" value in the warning messages:
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.114 msecs
Note, there was a second fix posted by Stephane Eranian for
a separate patch which I also botched:
Peter Zijlstra [Fri, 28 Jun 2013 09:18:53 +0000 (11:18 +0200)]
sched: Fix HRTICK
David reported that the HRTICK sched feature was borken; which was enough
motivation for me to finally fix it ;-)
We should not allow hrtimer code to do softirq wakeups while holding scheduler
locks. The hrtimer code only needs this when we accidentally try to program an
expired time. We don't much care about those anyway since we have the regular
tick to fall back to.
Stephen Boyd [Thu, 11 Jul 2013 14:00:59 +0000 (07:00 -0700)]
tick: broadcast: Check broadcast mode on CPU hotplug
On ARM systems the dummy clockevent is registered with the cpu
hotplug notifier chain before any other per-cpu clockevent. This
has the side-effect of causing the dummy clockevent to be
registered first in every hotplug sequence. Because the dummy is
first, we'll try to turn the broadcast source on but the code in
tick_device_uses_broadcast() assumes the broadcast source is in
periodic mode and calls tick_broadcast_start_periodic()
unconditionally.
On boot this isn't a problem because we typically haven't
switched into oneshot mode yet (if at all). During hotplug, if
the broadcast source isn't in periodic mode we'll replace the
broadcast oneshot handler with the broadcast periodic handler and
start emulating oneshot mode when we shouldn't. Due to the way
the broadcast oneshot handler programs the next_event it's
possible for it to contain KTIME_MAX and cause us to hang the
system when the periodic handler tries to program the next tick.
Fix this by using the appropriate function to start the broadcast
source.
Reported-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Mark Rutland <Mark.Rutland@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: ARM kernel mailing list <linux-arm-kernel@lists.infradead.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Joseph Lo <josephl@nvidia.com> Link: http://lkml.kernel.org/r/20130711140059.GA27430@codeaurora.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Peter Zijlstra [Fri, 12 Jul 2013 09:08:33 +0000 (11:08 +0200)]
perf: Fix perf_lock_task_context() vs RCU
Jiri managed to trigger this warning:
[] ======================================================
[] [ INFO: possible circular locking dependency detected ]
[] 3.10.0+ #228 Tainted: G W
[] -------------------------------------------------------
[] p/6613 is trying to acquire lock:
[] (rcu_node_0){..-...}, at: [<ffffffff810ca797>] rcu_read_unlock_special+0xa7/0x250
[]
[] but task is already holding lock:
[] (&ctx->lock){-.-...}, at: [<ffffffff810f2879>] perf_lock_task_context+0xd9/0x2c0
[]
[] which lock already depends on the new lock.
[]
[] the existing dependency chain (in reverse order) is:
[]
[] -> #4 (&ctx->lock){-.-...}:
[] -> #3 (&rq->lock){-.-.-.}:
[] -> #2 (&p->pi_lock){-.-.-.}:
[] -> #1 (&rnp->nocb_gp_wq[1]){......}:
[] -> #0 (rcu_node_0){..-...}:
Paul was quick to explain that due to preemptible RCU we cannot call
rcu_read_unlock() while holding scheduler (or nested) locks when part
of the read side critical section was preemptible.
Therefore solve it by making the entire RCU read side non-preemptible.
Also pull out the retry from under the non-preempt to play nice with RT.
Reported-by: Jiri Olsa <jolsa@redhat.com> Helped-out-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jiri Olsa [Tue, 9 Jul 2013 15:44:11 +0000 (17:44 +0200)]
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
The '!ctx->is_active' check has a valid scenario, so
there's no need for the warning.
The reason is that there's a time window between the
'ctx->is_active' check in the perf_event_enable() function
and the __perf_event_enable() function having:
- IRQs on
- ctx->lock unlocked
where the task could be killed and 'ctx' deactivated by
perf_event_exit_task(), ending up with the warning below.
So remove the WARN_ON_ONCE() check and add comments to
explain it all.
This addresses the following warning reported by Vince Weaver:
Jiri Olsa [Tue, 9 Jul 2013 15:44:10 +0000 (17:44 +0200)]
perf: Clone child context from parent context pmu
Currently when the child context for inherited events is
created, it's based on the pmu object of the first event
of the parent context.
This is wrong for the following scenario:
- HW context having HW and SW event
- HW event got removed (closed)
- SW event stays in HW context as the only event
and its pmu is used to clone the child context
The issue starts when the cpu context object is touched
based on the pmu context object (__get_cpu_context). In
this case the HW context will work with SW cpu context
ending up with following WARN below.
Fixing this by using parent context pmu object to clone
from child context.
Addresses the following warning reported by Vince Weaver:
Wolfram Sang [Wed, 10 Jul 2013 15:57:44 +0000 (16:57 +0100)]
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Wed, 10 Jul 2013 15:57:43 +0000 (16:57 +0100)]
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Wed, 10 Jul 2013 15:57:42 +0000 (16:57 +0100)]
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Base on cdc_ether, add the mii functions for RTL8152 and RTL8153.
The RTL8152 and RTL8153 support ECM mode which use the driver of
cdc_ether. Add the mii functions. Then, the basic PHY access is
possible.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 10 Jul 2013 10:58:59 +0000 (13:58 +0300)]
mlx5: Return -EFAULT instead of -EPERM
For copy_to/from_user() failure, the correct error code is -EFAULT not
-EPERM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Dean Luick [Thu, 11 Jul 2013 19:32:14 +0000 (15:32 -0400)]
IB/qib: Log all SDMA errors unconditionally
This patch adds code to log SDMA errors for supportability purposes.
Signed-off-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
The vzalloc()'ed field physshadow is leaked on module unload.
This patch adds vfree after the sibling page shadow is freed.
Reported-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
Sparse reported an endianness bug in the assignment to hca_cap.uar_page_sz.
Fix the declaration of this field to be __be16 (which is what is in
the firmware spec), renaming the field to log_uar_pg_size to conform
to the spec, which fixes the endianness bug reported by sparse.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Moshe Lazer <moshel@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
If the transport layer is offline it is more appropriate to let
srp_abort() return FAST_IO_FAIL instead of SUCCESS.
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com> Acked-by: David Dillow <dillowda@ornl.gov> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Roland Dreier <roland@purestorage.com>
Alexander Duyck [Thu, 11 Jul 2013 20:12:22 +0000 (13:12 -0700)]
gre: Fix MTU sizing check for gretap tunnels
This change fixes an MTU sizing issue seen with gretap tunnels when non-gso
packets are sent from the interface.
In my case I was able to reproduce the issue by simply sending a ping of
1421 bytes with the gretap interface created on a device with a standard
1500 mtu.
This fix is based on the fact that the tunnel mtu is already adjusted by
dev->hard_header_len so it would make sense that any packets being compared
against that mtu should also be adjusted by hard_header_len and the tunnel
header instead of just the tunnel header.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reported-by: Cong Wang <amwang@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Shilovsky [Thu, 11 Jul 2013 07:17:45 +0000 (11:17 +0400)]
CIFS: Fix a deadlock when a file is reopened
If we request reading or writing on a file that needs to be
reopened, it causes the deadlock: we are already holding rw
semaphore for reading and then we try to acquire it for writing
in cifs_relock_file. Fix this by acquiring the semaphore for
reading in cifs_relock_file due to we don't make any changes in
locks and don't need a write access.
CC: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
Pavel Shilovsky [Thu, 11 Jul 2013 06:58:30 +0000 (10:58 +0400)]
CIFS: Reopen the file if reconnect durable handle failed
This is a follow-on patch for 8/8 patch from the durable handles
series. It fixes the problem when durable file handle timeout
expired on the server and reopen returns -ENOENT for such files. Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Steve French <smfrench@gmail.com>
xfs: Fix the logic check for all quotas being turned off
During the review of seperate pquota inode patches, David noticed
that the test to detect all quotas being turned off was
incorrect, and hence the block was not freeing all the quota
information.
The check made sense in Irix, but in Linux, quota is turned off
one at a time, which makes the test invalid for Linux.
This problem existed since XFS was ported to Linux.
David suggested to fix the problem by detecting when all quotas are
turned off by checking m_qflags.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
This patch is being created to use the UEFI bits in the type 219 SMBIOS
record in order to decide whether or not to execute BIOS code. This is a
better solution than to depend on the iCRU bit since not all future servers
will use iCRU.
In watchdog_ping(), 'start' is called automatically when 'ping' function call
is not configured.
Softdog driver has same handling in both cases - start and ping, so 'ping' OPS
can be removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog: New watchdog driver for MEN A21 watchdogs
This patch adds the driver for the watchdog devices found on MEN Mikro
Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the
watchdog framework.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Russell King [Tue, 18 Jun 2013 16:20:32 +0000 (17:20 +0100)]
Watchdog: fix clearing of the watchdog interrupt
The bits in BRIDGE_CAUSE are documented as RW0C - read, write 0 to
clear. If we read the register, mask off the watchdog bit, and
write it back, we're actually clearing every interrupt which wasn't
pending at the time we read the register - and that is racy.
Fix this to only write ~WATCHDOG_BIT to the register, which means
we write as zero only the watchdog bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Jason Cooper <jason@lakedaemon.net> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
projects / karo-tx-linux.git / log