V4L/DVB (9869): gspca - zc3xx: Change the USB exchanges for the sensor pas202b.
This sensor was declared as hdcs2020.
The new exchanges have been extracted from the ms-win file usbvm31b.inf.
The light frequency control has been added.
Jim Paris [Thu, 4 Dec 2008 07:52:40 +0000 (04:52 -0300)]
V4L/DVB (9860): gspca - ov534: Frame transfer improvements.
The indirect registers at 0x1c/0x1d control frame settings. If we
leave the values at 0x0a and 0x0b at their reset-time defaults, frame
data from the camera matches the UVC payload format. This lets us
better reassemble the data into frames and know when data was lost.
This also lets us relax the bulk_size requirement from 600K to 2K,
which should help systems on with limited RAM (like the PS3).
Signed-off-by: Jim Paris <jim@jtan.com> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (9811): Add support for the CX24113 DVB-S tuner driver
This commit adds support for the CX24113 DVB-S tuner driver and thus support for the Technisat Skystar2 revision 2.8.
The driver was created with the help of Technisat. Thank you very much.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (9810): uvcvideo: Add a device quirk to prune bogus controls.
Bogus controls currently include processing unit auto controls for which no
corresponding manual control is available. Such auto controls make little
sense if any, and are known to crash at least the SiGma Micro webcam.
V4L/DVB (9809): uvcvideo: Add nodrop module parameter to turn incomplete frame drop off.
The driver drops incomplete uncompressed video frames to avoid confusing
userspace with corrupt data. Add a nodrop module parameter to turn that
behaviour off and make all frames available to userspace.
Andy Walls [Fri, 12 Dec 2008 19:24:04 +0000 (16:24 -0300)]
V4L/DVB (9805): cx18: Port fix for raw/sliced VBI mixup from ivtv and cx25840
This is a port of the fixes Hans Verkuil made for ivtv/cx25840:
The service_set field was used to determine whether raw or sliced VBI was
desired. This is incorrect since it is perfectly valid to select sliced VBI
with a service_set of 0.
Instead the driver should check on VIDIOC_S_FMT whether the type
field matches the raw or sliced VBI type.
Updated the cx18 driver accordingly, including an additional check in
cx18_start_v4l2_encode_stream() that didn't exist in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Fri, 12 Dec 2008 18:50:27 +0000 (15:50 -0300)]
V4L/DVB (9804): cx18: Avoid making firmware API calls with the queue lock held
cx18: Avoid making firmware API calls with the queue lock held. The source
of MPEG strem corruption when not holding the queue lock was found to be that
the MPEG buffer could be retrieved by the user app before it was sync'ed for
the host cpu. Incoming buffers are now sync'ed before being put on q_full and
releasing the queue lock. We can thus avoid the sometimes lengthy call to
the firmware for CPU_DE_SET_MDL while holding the queue lock, so we can get
better performance.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Mon, 8 Dec 2008 02:30:17 +0000 (23:30 -0300)]
V4L/DVB (9802): cx18: Add module parameters for finer control over buffer allocations
cx18: Add module parameters for finer control over buffer allocations.
User now has the option of setting smaller buffers to get lower
latency transfers from the encoder. User can also now set the number
of buffers used for a stream explicitly.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Tue, 9 Dec 2008 02:02:45 +0000 (23:02 -0300)]
V4L/DVB (9801): cx18: Allow more than 63 capture buffers in rotation per stream
cx18: Allow more than 63 capture buffers in rotation per stream. Implement
q_busy to hold buffers the firmware has for use. q_free holds truly unused
buffers in a pool. New buffers are given to the firmware as soon as the
firmware returns one, if there are any to give to the firmware.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Fri, 28 Nov 2008 03:04:21 +0000 (00:04 -0300)]
V4L/DVB (9800): cx18: Eliminate q_io from stream buffer handling
Eliminate q_io from stream buffer handling in anticipation of upcoming
changes in buffer handling. q_io was a holdover from ivtv and it's function
in cx18 was trivial and not necessary. We just push things back onto the
front of q_full now, instead of maintaining a 1 buffer q_io queue.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the function cx88_audio_initdev, the value card has been created using
snd_card_new. The other error handling code in this function frees the
value using snd_card_free. I have thus changed the first error case to do
the same. On the other hand, it may be that card is not sufficiently
initialized at this point to use snd_card_free, in which case something
else should be done to free the memory in the error case.
In the function snd_cx88_create the call kfree(chip) in one error case
looks suspicious, both because it is not done in the other error code, and
because chip points into the middle of the memory allocated by
snd_card_new, ie it is not itself associated with a separate kmalloc.
Therefore I have removed it.
The semantic match that finds the first problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S,S1;
position p1,p2,p3;
expression E,E1;
type T,T1;
expression *ptr != NULL;
@@
(
if ((x@p1 = snd_card_new(...)) == NULL) S
|
x@p1 = snd_card_new(...);
)
... when != snd_card_free(...,(T)x,...)
when != if (...) { <+... snd_card_free(...,(T)x,...) ...+> }
when != true x == NULL || ...
when != x = E
when != E = (T)x
when any
(
if (x == NULL || ...) S1
|
if@p2 (...) {
... when != snd_card_free(...,(T1)x,...)
when != if (...) { <+... snd_card_free(...,(T1)x,...) ...+> }
when != x = E1
when != E1 = (T1)x
(
return \(0\|<+...x...+>\|ptr\);
|
return@p3 ...;
)
}
)
Robert Jarzmik [Mon, 1 Dec 2008 12:45:35 +0000 (09:45 -0300)]
V4L/DVB (9791): pxa-camera: pixel format negotiation
Use the new format-negotiation infrastructure, support all four YUV422
packed and the planar formats.
The new translation structure enables to build the format
list with buswidth, depth, host format and camera format
checked, so that it's not done anymore on try_fmt nor
set_fmt.
V4L/DVB (9790): soc-camera: pixel format negotiation - core support
Allocate and fill a list of formats, supported by this specific
camera-host combination. Use it for format enumeration. Take care to stay
backwards-compatible.
Camera hosts rely on sensor formats available, as well as
host specific translations. We add a structure so that hosts
can define a translation table and use it for format check
and setup.
We anyway don't follow the s_fmt_vid_cap / g_fmt_vid_cap / try_fmt_vid_cap
naming, and soc-camera is so far only about video capture, let's simplify
operation names a bit further. set_fmt_cap / try_fmt_cap wasn't a very good
choice too.
V4L/DVB (9787): soc-camera: let camera host drivers decide upon pixel format
Pixel format requested by the user is not necessarily the same, as what
a sensor driver provides. There are situations, when a camera host driver
provides the required format, but requires a different format from the
sensor. Further, the list of formats, supported by sensors is pretty static
and can be pretty good described with a constant list of structures. Whereas
decisions, made by camera host drivers to support requested formats can be
quite complex, therefore it is better to let the host driver do the work.
V4L/DVB (9785): soc-camera: merge .try_bus_param() into .try_fmt_cap()
.try_bus_param() method from struct soc_camera_host_ops is only called at one
location immediately before .try_fmt_cap(), there is no value in keeping these
two methods separate, merge them.
Andy Walls [Sun, 30 Nov 2008 13:01:21 +0000 (10:01 -0300)]
V4L/DVB (9778): cx18: cx18_writel_expect() should not declare success on a PCI read error
cx18: cx18_writel_expect() should not declare success on a PCI read error.
This removes the potential for cx18_write*_expect() calls to not
accomplish a PCI write successfully as expected. The CX18-AV core uses the
*expect() calls often and this may be the source of intermittent audio
problems and standands switching problems.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 26 Nov 2008 00:43:05 +0000 (21:43 -0300)]
V4L/DVB (9776): cx18: Change to per CX23418 device work queues for deferrable work handling
cx18: Change to per CX23418 device work queues for deferrable work handling.
Needed to support 2.6.22 and earlier kernels that can't selectively cancel
work orders. Also will provide slightly better performance on SMP systems.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda8290 were using some random video standard for FM. This results on random
errors. Instead, program tda8290 in expert mode, using a configuration near the
one specified on NXP datasheet for tda8295 (available on their site).
Also, properly display that the device is on radio mode.
Probably due to a removed code, tda827x were doing some wrong calculus at the
returned frequency. I suspect that the original idea were to return the
programmed divisor converted into frequency again.
However, the current code is sometimes multiplying the programmed frequency by
62500, and, on other cases, like radio, it dividing it by 1000.
Instead of doing such math, let's just store the frequency value as requested by
the caller module.
Cc: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c: In function 'xc2028_sleep':
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c:1111: warning: 'return' with no value, in function returning non-void
V4L/DVB (9770): em28xx: turn off tuner when not used
em28xx devices generally get hot when xc3028 tuner is powered on. This
patch solves this by turning power off when the device is not used, at the
expense of having a higher load time, when calling a TV application.
Since firmware load happens on 1 or 2 seconds on most devices, this is not a pain.
Also, it helps to save the planet by saving some power :)
V4L/DVB (9769): tuner-xc2028: powers device of when not used
Since the firmware load is now fast on most boards, better to keep the tuner
off by default. A modprobe parameter were added to keep the old behavior,
to be used by old devices.
Andy Walls [Sun, 23 Nov 2008 19:27:57 +0000 (16:27 -0300)]
V4L/DVB (9730): cx18: Quiet a sometimes common warning that often has benign consequences
cx18: Quiet a sometimes common warning that often has benign consequences.
No one probably cares that the firmware took forever to ack our command, as
they always seem to succeed whether or not the firmware acks it in a reasonable
amount of time.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Adjust outgoing mailbox timeouts and remove statistics logging.
This saves some wasted storage in struct cx18 for each card. Cutting
the outgoing mailbox timeouts in half from the previous value appears to
be safe with MythTV. Got rid of interrupted case code path after
a wait uninterruptable returns.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Tue, 18 Nov 2008 01:48:46 +0000 (22:48 -0300)]
V4L/DVB (9725): cx18: Remove unnecessary MMIO accesses in time critical irq handling path
Remove unnecessary MMIO accesses in time critical irq handling path. Also
ensured that the mailbox ack field is read in last, so we know for sure if we
have a stale mailbox or not on receipt.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Streamline cx18-io[ch] wrappers and enforce MMIO retry strategy so that
write retries always occur and read retries never occur (as they never help).
Remove MMIO statistics logging to speed up MMIO accesses. Deprecate & ignore
retry_mmio and mmio_ndelay module parameters, to essentially force
retry_mmio=1 and mmio_ndelay=0.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Mon, 17 Nov 2008 00:18:00 +0000 (21:18 -0300)]
V4L/DVB (9723): cx18: Propagate staleness of mailbox and mdl ack data to work handler
cx18: Propagate staleness of mailbox and mdl ack data to work handler to let
the work handler know that the data from the encoder may not be coherent.
Allows for smarter handling of buffers in future, to deal with MDLs that fall
out of rotation due to irq handler being late in collecting mailbox and mdl ack
info.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 16 Nov 2008 23:18:05 +0000 (20:18 -0300)]
V4L/DVB (9722): cx18: Convert per stream queue spinlocks into mutexes
Convert the per stream queue spinlocks into mutexes. All queue
manipulation happens via the work queue or system calls into the driver, and
not in an interrupt context. This reduces the amout of time the cx18 driver
keeps interrupts disabled.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 16 Nov 2008 20:15:01 +0000 (17:15 -0300)]
V4L/DVB (9721): cx18: Change to singlethreaded global work queue thread for deferable work
Change to singlethreaded global work queue thread for deferable work,
instead of the kernel default multithreaded work queue. This ensures
execution of deferable work is always in the proper order, so caputred buffers
don't get reordered.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 16 Nov 2008 04:38:19 +0000 (01:38 -0300)]
V4L/DVB (9720): cx18: Major rewrite of interrupt handling for incoming mailbox processing
A major rewrite of interrupt handling for incoming mailbox processing, to split
the timing critical steps from the the deferrable steps as the sending XPU on
the CX23418 will time out and overwrite our incoming mailboxes rather quickly.
Setup a pool of work "order forms" for the irq handler to send jobs to the new
work handler routine which uses the kernel default work queue to do the
deferrable work. Started optimizing some of the cx18-io calls as they are now
the low hanging fruit for recoving microseconds back from the timeline.
Future optimizations will get rid of mmio read retries, mmio stats logging, and
combine smaller functions in the irq path into the larger ones to save ~2 us
each.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mv-sheeva.git / log