md: writing to sync_action should clear the read-auto state.
In some cases array are started in 'read-auto' state where in
nothing gets written to any device until the array is written
to. The purpose of this is to make accidental auto-assembly
of the wrong arrays less of a risk, and to allow arrays to be
started to read suspend-to-disk images without actually changing
anything (as might happen if the array were dirty and a
resync seemed necessary).
Explicitly writing the 'sync_action' for a read-auto array currently
doesn't clear the read-auto state, so the sync action doesn't
happen, which can be confusing.
So allow any successful write to sync_action to clear any read-auto
state.
Reported-by: Alexander Kühn <alexander.kuehn@nagilum.de> Signed-off-by: NeilBrown <neilb@suse.de>
md/raid5: make sure to_read and to_write never go negative.
to_read and to_write are part of the result of analysing
a stripe before handling it.
Their use is to avoid some loops and tests if the values are
known to be zero. Thus it is not a problem if they are a
little bit larger than they should be.
So decrementing them in handle_failed_stripe serves little value, and
due to races it could cause some loops to be skipped incorrectly.
If 'resync_max' is set to 0 (as is often done when starting a
reshape, so the mdadm can remain in control during a sensitive
period), and if the reshape request is initially delayed because
another array using the same array is resyncing or reshaping etc,
when user-space cannot easily tell when the delay changes from being
due to a conflicting reshape, to being due to resync_max = 0.
So introduce a new state: (curr_resync == 3) to reflect this, make
sure it is visible both via /proc/mdstat and via the "sync_completed"
sysfs attribute, and ensure that the event transition from one delay
state to the other is properly notified.
md/raid5: be careful not to resize_stripes too big.
When a RAID5 is reshaping, conf->raid_disks is increased
before mddev->delta_disks becomes zero.
This can result in check_reshape calling resize_stripes with a
number that is too large. This particularly happens
when md_check_recovery calls ->check_reshape().
If we use ->previous_raid_disks, we don't risk this.
Shaohua Li [Thu, 27 Sep 2012 02:37:28 +0000 (12:37 +1000)]
MD: raid5 avoid unnecessary zero page for trim
We want to avoid zero discarded dev page, because it's useless for discard.
But if we don't zero it, another read/write hit such page in the cache and will
get inconsistent data.
To avoid zero the page, we don't set R5_UPTODATE flag after construction is
done. In this way, discard write request is still issued and finished, but read
will not hit the page. If the stripe gets accessed soon, we need reread the
stripe, but since the chance is low, the reread isn't a big deal.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
Shaohua Li [Thu, 27 Sep 2012 02:37:27 +0000 (12:37 +1000)]
MD: raid5 trim support
Discard for raid4/5/6 has limitation. If discard request size is
small, we do discard for one disk, but we need calculate parity and
write parity disk. To correctly calculate parity, zero_after_discard
must be guaranteed. Even it's true, we need do discard for one disk
but write another disks, which makes the parity disks wear out
fast. This doesn't make sense. So an efficient discard for raid4/5/6
should discard all data disks and parity disks, which requires the
write pattern to be (A, A+chunk_size, A+chunk_size*2...). If A's size
is smaller than chunk_size, such pattern is almost impossible in
practice. So in this patch, I only handle the case that A's size
equals to chunk_size. That is discard request should be aligned to
stripe size and its size is multiple of stripe size.
Since we can only handle request with specific alignment and size (or
part of the request fitting stripes), we can't guarantee
zero_after_discard even zero_after_discard is true in low level
drives.
The block layer doesn't send down correctly aligned requests even
correct discard alignment is set, so I must filter out.
For raid4/5/6 parity calculation, if data is 0, parity is 0. So if
zero_after_discard is true for all disks, data is consistent after
discard. Otherwise, data might be lost. Let's consider a scenario:
discard a stripe, write data to one disk and write parity disk. The
stripe could be still inconsistent till then depending on using data
from other data disks or parity disks to calculate new parity. If the
disk is broken, we can't restore it. So in this patch, we only enable
discard support if all disks have zero_after_discard.
If discard fails in one disk, we face the similar inconsistent issue
above. The patch will make discard follow the same path as normal
write request. If discard fails, a resync will be scheduled to make
the data consistent. This isn't good to have extra writes, but data
consistency is important.
If a subsequent read/write request hits raid5 cache of a discarded
stripe, the discarded dev page should have zero filled, so the data is
consistent. This patch will always zero dev page for discarded request
stripe. This isn't optimal because discard request doesn't need such
payload. Next patch will avoid it.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
md/raid1: Don't release reference to device while handling read error.
When we get a read error, we arrange for raid1d to handle it.
Currently we release the reference on the device. This can result
in
conf->mirrors[read_disk].rdev
being NULL in fix_read_error, if the device happens to get removed
before the read error is handled.
So instead keep the reference until the read error has been fully
handled.
Michael Wang [Thu, 27 Sep 2012 02:37:27 +0000 (12:37 +1000)]
raid: replace list_for_each_continue_rcu with new interface
This patch replaces list_for_each_continue_rcu() with
list_for_each_entry_continue_rcu() to save a few lines
of code and allow removing list_for_each_continue_rcu().
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Michael Wang <wangyun@linux.vnet.ibm.com> Signed-off-by: NeilBrown <neilb@suse.de>
Jonathan Brassow [Thu, 27 Sep 2012 02:37:26 +0000 (12:37 +1000)]
DM RAID: Fix for "sync" directive ineffectiveness
There are two table arguments that can be given to a DM RAID target
that control whether the array is forced to (re)synchronize or skip
initialization: "sync" and "nosync". When "sync" is given, we set
mddev->recovery_cp to 0 in order to cause the device to resynchronize.
This is insufficient if there is a bitmap in use, because the array
will simply look at the bitmap and see that there is no recovery
necessary.
The fix is to skip over the loading of the superblocks when "sync" is
given, causing new superblocks to be written that will force the array
to go through initialization (i.e. synchronization).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: NeilBrown <neilb@suse.de>
Jonathan Brassow [Thu, 27 Sep 2012 02:37:26 +0000 (12:37 +1000)]
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
The "rebuild" parameter takes an index argument that starts counting from
zero. The conditional used to validate the index was using '>' rather than
'>=', leaving the door open for an index value that would be 1 too large.
Reported-by: Neil Brown <neilb@suse.de> Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: NeilBrown <neilb@suse.de>
Jonathan Brassow [Thu, 27 Sep 2012 02:37:26 +0000 (12:37 +1000)]
DM RAID: Add rebuild capability for RAID10
DM RAID: Add code to validate replacement slots for RAID10 arrays
RAID10 can handle 'copies - 1' failures for each mirror group. This code
ensures the user has provided a valid array - one whose devices specified for
rebuild do not exceed the amount of redundancy available.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: NeilBrown <neilb@suse.de>
Jonathan Brassow [Thu, 27 Sep 2012 02:37:25 +0000 (12:37 +1000)]
DM RAID: Move 'rebuild' checking code to its own function
DM RAID: Move chunk of code to it's own function
The code that checks whether device replacements/rebuilds are possible given
a specific RAID type is moved to it's own function. It will further expand
when the code to check RAID10 is added. A separate function makes it easier
to read.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: NeilBrown <neilb@suse.de>
Jonathan Brassow [Thu, 27 Sep 2012 02:37:25 +0000 (12:37 +1000)]
MD RAID10: Prep for DM RAID10 device replacement capability
MD RAID10: Fix a couple potential kernel panics if RAID10 is used by dm-raid
When device-mapper uses the RAID10 personality through dm-raid.c, there is no
'gendisk' structure in mddev and some sysfs information is also not populated.
This patch avoids touching those non-existent structures.
Signed-off-by: Jonathan Brassow <jbrassow@rehdat.com> Signed-off-by: NeilBrown <neilb@suse.de>
Some ioctls don't need to take the mutex and doing so can cause
a delay as it is held during super-block update.
So move those ioctls out of the mutex and rely on rcu locking
to ensure we don't access stale data.
Shaohua Li [Thu, 27 Sep 2012 02:37:24 +0000 (12:37 +1000)]
raid5: create multiple threads to handle stripes
This is a new tempt to make raid5 handle stripes in multiple threads, as
suggested by Neil to have maxium flexibility and better numa binding. It
basically is a combination of my first and second generation patches. By
default, no multiple thread is enabled (all stripes are handled by raid5d).
An example to enable multiple threads:
#echo 3 > /sys/block/md0/md/auxthread_number
This will create 3 auxiliary threads to handle stripes. The threads can run
on any cpus and handle stripes produced by any cpus.
#echo 1-3 > /sys/block/md0/md/auxth0/cpulist
This will bind auxiliary thread 0 to cpu 1-3, and this thread will only handle
stripes produced by cpu 1-3. User tool can further change the thread's
affinity, but the thread can only handle stripes produced by cpu 1-3 till the
sysfs entry is changed again.
If stripes produced by a CPU aren't handled by any auxiliary thread, such
stripes will be handled by raid5d. Otherwise, raid5d doesn't handle any
stripes.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
md/raid10: submit IO from originating thread instead of md thread.
queuing writes to the md thread means that all requests go through the
one processor which may not be able to keep up with very high request
rates.
So use the plugging infrastructure to submit all requests on unplug.
If a 'schedule' is needed, we fall back on the old approach of handing
the requests to the thread for it to handle.
This is nearly identical to a recent patch which provided similar
functionality to RAID1.
Shaohua Li [Thu, 27 Sep 2012 02:37:24 +0000 (12:37 +1000)]
md: raid 10 supports TRIM
This makes md raid 10 support TRIM.
If one disk supports discard and another not, or one has
discard_zero_data and another not, there could be inconsistent between
data from such disks. But this should not matter, discarded data is
useless. This will add extra copy in rebuild though.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
Shaohua Li [Thu, 27 Sep 2012 02:37:23 +0000 (12:37 +1000)]
md: raid 1 supports TRIM
This makes md raid 1 support TRIM.
If one disk supports discard and another not, or one has discard_zero_data and
another not, there could be inconsistent between data from such disks. But this
should not matter, discarded data is useless. This will add extra copy in rebuild
though.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
According to the comment in linear_stop function
rcu_dereference in linear_start and linear_stop functions
occurs under reconfig_mutex. The patch represents this
agreement in code and prevents lockdep complaint.
Found by Linux Driver Verification project (linuxtesting.org)
md/raid10: fix "enough" function for detecting if array is failed.
The 'enough' function is written to work with 'near' arrays only
in that is implicitly assumes that the offset from one 'group' of
devices to the next is the same as the number of copies.
In reality it is the number of 'near' copies.
So change it to make this number explicit.
This bug makes it possible to run arrays without enough drives
present, which is dangerous.
It is appropriate for an -stable kernel, but will almost certainly
need to be modified for some of them.
Cc: stable@vger.kernel.org Reported-by: Jakub Husák <jakub@gooseman.cz> Signed-off-by: NeilBrown <neilb@suse.de>
added a spin_lock to the 'stripe_head' struct.
Unfortunately there are two places where this struct is allocated
but the spin lock was only initialised in one of them.
md: make sure metadata is updated when spares are activated or removed.
It isn't always necessary to update the metadata when spares are
removed as the presence-or-not of a spare isn't really important to
the integrity of an array.
Also activating a spare doesn't always require updating the metadata
as the update on 'recovery-completed' is usually sufficient.
However the introduction of 'replacement' devices have made these
transitions sometimes more important. For example the 'Replacement'
flag isn't cleared until the original device is removed, so we need
to ensure a metadata update after that 'spare' is removed.
So set MD_CHANGE_DEVS whenever a spare is activated or removed, to
complement the current situation where it is set when a spare is added
or a device is failed (or a number of other less common situations).
This is suitable for -stable as out-of-data metadata could lead
to data corruption.
This is only relevant for 3.3 and later 9when 'replacement' as
introduced.
md/raid5: fix calculate of 'degraded' when a replacement becomes active.
When a replacement device becomes active, we mark the device that it
replaces as 'faulty' so that it can subsequently get removed.
However 'calc_degraded' only pays attention to the primary device, not
the replacement, so the array appears to become degraded, which is
wrong.
So teach 'calc_degraded' to consider any replacement if a primary
device is faulty.
This is suitable for -stable as an incorrect 'degraded' value can
confuse md and could lead to data corruption.
This is only relevant for 3.3 and later.
Cc: stable@vger.kernel.org Reported-by: Robin Hill <robin@robinhill.me.uk> Reported-by: John Drescher <drescherjm@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
While this patch seemed like a good idea and did help some workloads,
it hurts other workloads.
Large sequential O_DIRECT writes were faster,
Small random O_DIRECT writes were slower.
Other changes (batching RAID5 writes) have improved the sequential
writes using a different mechanism, so the net result of this patch
is definitely negative. So revert it.
Reported-by: Shaohua Li <shli@kernel.org> Tested-by: Jianpeng Ma <majianpeng@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
Merge branch 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit e9da6e9905e6 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for EMR on Cintiq 24HD touch
Input: i8042 - add Gigabyte T1005 series netbooks to noloop table
Input: imx_keypad - reset the hardware before enabling
Input: edt-ft5x06 - fix build error when compiling wthout CONFIG_DEBUG_FS
Merge branch 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
performance improvement (not processing debug data if noone is
interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
work even with generic driver in a crippled mode, by Andres Freund."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
HID: Only dump input if someone is listening
HID: add NOGET quirk for Eaton Ellipse MAX UPS
Andres Freund [Thu, 30 Aug 2012 12:37:14 +0000 (14:37 +0200)]
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
c1dcad2d32d0252e8a3023d20311b52a187ecda3 added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Fix proper FLR steps.
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
Merge tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled"
* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't print anything while decoding is disabled
PCI/PM: Add ABI document for sysfs file d3cold_allowed
PCI/PM: Fix config reg access for D3cold and bridge suspending
PCI/PM: Keep parent bridge active when probing device
PCI/PM: Enable D3/D3cold by default for most devices
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Olof Johansson:
"Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: gemini: fix the gemini build
ARM: shmobile: armadillo800eva: enable rw rootfs mount
ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
ARM: shmobile: mackerel: fixup usb module order
ARM: shmobile: armadillo800eva: fixup: sound card detection order
ARM: shmobile: marzen: fixup smsc911x id for regulator
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull a hwmon fix from Guenter Roeck:
"One patch, fixing DIV_ROUND_CLOSEST to support negative dividends.
While the changes are not in the drivers/hwmon directory, the problem
primarily affects hwmon drivers, and it makes sense to push the patch
through the hwmon tree."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
linux/kernel.h: Fix DIV_ROUND_CLOSEST to support negative dividends
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"These are two fixes that should go into 3.6. The link-vmlinux.sh one
is obvious.
The other one fixes make firmware_install with certain configurations,
where a file in the toplevel firmware tree gets installed first, and
$(INSTALL_FW_PATH)/$$(dir <file>) results in /lib/firmware/./, which
confuses make 3.82 for some reason."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
firmware: fix directory creation rule matching with make 3.82
link-vmlinux.sh: Fix stray "echo" in error message
When we do FLR and save PCI config we did it in the wrong order.
The end result was that if a PCI device was unbind from
its driver, then binded to xen-pciback, and then back to its
driver we would get:
Merge tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- a firmware bug on several Samsung MoviNAND eMMC models causes
permanent corruption on the device when secure erase and secure trim
requests are made, so we disable those requests on these eMMC devices.
- atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
- dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
fix handling of error interrupts.
- mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
- omap: fix broken PIO mode causing memory corruption.
- sdhci-esdhc: fix card detection.
* tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: omap: fix broken PIO mode
mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
mmc: dw_mmc: fix error handling in PIO mode
mmc: dw_mmc: correct mishandling error interrupt
mmc: dw_mmc: amend using error interrupt status
mmc: atmel-mci: not busy flag has also to be used for read operations
mmc: sdhci-esdhc: break out early if clock is 0
mmc: mxs-mmc: fix deadlock caused by recursion loop
mmc: mxs-mmc: fix deadlock in SDIO IRQ case
mmc: bfin_sdh: fix dma_desc_array build error
arch/um/os-Linux/time.c: In function 'deliver_alarm':
arch/um/os-Linux/time.c:117:3: error: too few arguments to function 'alarm_handler'
arch/um/os-Linux/internal.h:1:6: note: declared here
The error was introduced by commit d3c1cfcd ("um: pass siginfo to guest
process") in 3.6-rc1.
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few fixes for 3.6 that were piling up while I was away or
busy (I was mostly MIA a week or two before San Diego).
Some fixes from Anton fixing up issues with our relatively new DSCR
control feature, and a few other fixes that are either regressions or
bugs nasty enough to warrant not waiting."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
Merge tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"These are some GPIO regression fixes for v3.6:
- Erroneous debug message from of_get_named_gpio_flags()
- Make sure the MC9S08DZ60 GPIO driver depend on I2C being compiled
in (not module) or allmodconfig breaks.
- Check return value from irq_alloc_descs() in the Emma Mobile GPIO
driver.
- Assign the owner field for the rdc321x driver so the module won't
be removed if it has active GPIOs."
* tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: rdc321x: Prevent removal of modules exporting active GPIOs
gpio: em: Fix checking return value of irq_alloc_descs
gpio: mc9s08dz60: Fix build error if I2C=m
gpio: Fix debug message in of_get_named_gpio_flags()
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"There are nothing scaring, contains only small fixes for HD-audio and
USB-audio:
- EPSS regression fix and GPIO fix for HD-audio IDT codecs
- A series of USB-audio regression fixes that are found since 3.5
kernel"
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: snd-usb: fix cross-interface streaming devices
ALSA: snd-usb: fix calls to next_packet_size
ALSA: snd-usb: restore delay information
ALSA: snd-usb: use list_for_each_safe for endpoint resources
ALSA: snd-usb: Fix URB cancellation at stream start
ALSA: hda - Don't trust codec EPSS bit for IDT 92HD83xx & co
ALSA: hda - Avoid unnecessary parameter read for EPSS
ALSA: hda - Do not set GPIOs for speakers on IDT if there are no speakers
Merge tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- a fix by Paul Cercueil to prevent a possible buffer overflow
- a fix by Bruno Prémont to prevent a rare sleep in invalid context
- a fix by Julia Lawall for a double free in auo_k190x
- a fix by Dan Carpenter to prevent a division by zero in mb862xxfb
- a regression fix by Tomi Valkeinen for the SDI output in OMAP
- a fix by Grazvydas Ignotas to fix the console colors in OMAP
* tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6:
OMAPFB: fix framebuffer console colors
OMAPDSS: Fix SDI PLL locking
video: mb862xxfb: prevent divide by zero bug
drivers/video/auo_k190x.c: drop kfree of devm_kzalloc's data
fbcon: Fix bit_putcs() call to kmalloc(s, GFP_KERNEL)
fbcon: prevent possible buffer overflow.
Merge tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi
Pull ubi fix from Artem Bityutskiy:
"A single small fix for memory deallocation: we allocated memory using
'kmem_cache_alloc()' but were freeing it using 'kfree()' in some
cases. Now we fix this by using 'kmem_cache_free()' instead."
* tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi:
UBI: fix a horrible memory deallocation bug
Fix order of arguments to compat_put_time[spec|val]
Commit 644595f89620 ("compat: Handle COMPAT_USE_64BIT_TIME in
net/socket.c") introduced a bug where the helper functions to take
either a 64-bit or compat time[spec|val] got the arguments in the wrong
order, passing the kernel stack pointer off as a user pointer (and vice
versa).
Because of the user address range check, that in turn then causes an
EFAULT due to the user pointer range checking failing for the kernel
address. Incorrectly resuling in a failed system call for 32-bit
processes with a 64-bit kernel.
On odder architectures like HP-PA (with separate user/kernel address
spaces), it can be used read kernel memory.
Ronny Hegewald [Fri, 31 Aug 2012 09:57:52 +0000 (09:57 +0000)]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
When running 32-bit pvops-dom0 and a driver tries to allocate a coherent
DMA-memory the xen swiotlb-implementation returned memory beyond 4GB.
The underlaying reason is that if the supplied driver passes in a
DMA_BIT_MASK(64) ( hwdev->coherent_dma_mask is set to 0xffffffffffffffff)
our dma_mask will be u64 set to 0xffffffffffffffff even if we set it to
DMA_BIT_MASK(32) previously. Meaning we do not reset the upper bits.
By using the dma_alloc_coherent_mask function - it does the proper casting
and we get 0xfffffffff.
This caused not working sound on a system with 4 GB and a 64-bit
compatible sound-card with sets the DMA-mask to 64bit.
On bare-metal and the forward-ported xen-dom0 patches from OpenSuse a coherent
DMA-memory is always allocated inside the 32-bit address-range by calling
dma_alloc_coherent_mask.
This patch adds the same functionality to xen swiotlb and is a rebase of the
original patch from Ronny Hegewald which never got upstream b/c the
underlaying reason was not understood until now.
The original email with the original patch is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-02/msg00038.html
the original thread from where the discussion started is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-01/msg00928.html
Signed-off-by: Ronny Hegewald <ronny.hegewald@online.de> Signed-off-by: Stefano Panella <stefano.panella@citrix.com> Acked-By: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> CC: stable@vger.kernel.org
Alex Shi [Fri, 24 Aug 2012 08:55:13 +0000 (08:55 +0000)]
xen: fix logical error in tlb flushing
While TLB_FLUSH_ALL gets passed as 'end' argument to
flush_tlb_others(), the Xen code was made to check its 'start'
parameter. That may give a incorrect op.cmd to MMUEXT_INVLPG_MULTI
instead of MMUEXT_TLB_FLUSH_MULTI. Then it causes some page can not
be flushed from TLB.
This patch fixed this issue.
Reported-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Alex Shi <alex.shi@intel.com> Acked-by: Jan Beulich <jbeulich@suse.com> Tested-by: Yongjie Ren <yongjie.ren@intel.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit '4cb38750d49010ae72e718d46605ac9ba5a851b4': (6849 commits)
bcma: fix invalid PMU chip control masks
[libata] pata_cmd64x: whitespace cleanup
libata-acpi: fix up for acpi_pm_device_sleep_state API
sata_dwc_460ex: device tree may specify dma_channel
ahci, trivial: fixed coding style issues related to braces
ahci_platform: add hibernation callbacks
libata-eh.c: local functions should not be exposed globally
libata-transport.c: local functions should not be exposed globally
sata_dwc_460ex: support hardreset
ata: use module_pci_driver
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
pata_imx: Convert to clk_prepare_enable/clk_disable_unprepare
ahci: Enable SB600 64bit DMA on MSI K9AGM2 (MS-7327) v2
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
drivers/acpi/glue: revert accidental license-related 6b66d95895c bits
libata-acpi: add missing inlines in libata.h
i2c-omap: Add support for I2C_M_STOP message flag
i2c: Fall back to emulated SMBus if the operation isn't supported natively
i2c: Add SCCB support
i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converter
...
xen/p2m: Fix one-off error in checking the P2M tree directory.
We would traverse the full P2M top directory (from 0->MAX_DOMAIN_PAGES
inclusive) when trying to figure out whether we can re-use some of the
P2M middle leafs.
Which meant that if the kernel was compiled with MAX_DOMAIN_PAGES=512
we would try to use the 512th entry. Fortunately for us the p2m_top_index
has a check for this:
powerpc: Don't use __put_user() in patch_instruction
patch_instruction() can be called very early on ppc32, when the kernel
isn't yet running at it's linked address. That can cause the !
is_kernel_addr() test in __put_user() to trip and call might_sleep()
which is very bad at that point during boot.
Use a lower level function instead for now, at least until we get to
rework ppc32 boot process to do the code patching later, like ppc64
does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Tue, 4 Sep 2012 18:33:08 +0000 (18:33 +0000)]
powerpc: Make sure IPI handlers see data written by IPI senders
We have been observing hangs, both of KVM guest vcpu tasks and more
generally, where a process that is woken doesn't properly wake up and
continue to run, but instead sticks in TASK_WAKING state. This
happens because the update of rq->wake_list in ttwu_queue_remote()
is not ordered with the update of ipi_message in
smp_muxed_ipi_message_pass(), and the reading of rq->wake_list in
scheduler_ipi() is not ordered with the reading of ipi_message in
smp_ipi_demux(). Thus it is possible for the IPI receiver not to see
the updated rq->wake_list and therefore conclude that there is nothing
for it to do.
In order to make sure that anything done before smp_send_reschedule()
is ordered before anything done in the resulting call to scheduler_ipi(),
this adds barriers in smp_muxed_message_pass() and smp_ipi_demux().
The barrier in smp_muxed_message_pass() is a full barrier to ensure that
there is a full ordering between the smp_send_reschedule() caller and
scheduler_ipi(). In smp_ipi_demux(), we use xchg() rather than
xchg_local() because xchg() includes release and acquire barriers.
Using xchg() rather than xchg_local() makes sense given that
ipi_message is not just accessed locally.
This moves the barrier between setting the message and calling the
cause_ipi() function into the individual cause_ipi implementations.
Most of them -- those that used outb, out_8 or similar -- already had
a full barrier because out_8 etc. include a sync before the MMIO
store. This adds an explicit barrier in the two remaining cases.
These changes made no measurable difference to the speed of IPIs as
measured using a simple ping-pong latency test across two CPUs on
different cores of a POWER7 machine.
The analysis of the reason why processes were not waking up properly
is due to Milton Miller.
Cc: stable@vger.kernel.org # v3.0+ Reported-by: Milton Miller <miltonm@bga.com> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Mon, 3 Sep 2012 16:51:10 +0000 (16:51 +0000)]
powerpc: Restore correct DSCR in context switch
During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.
Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.
This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):
Anton Blanchard [Mon, 3 Sep 2012 16:49:47 +0000 (16:49 +0000)]
powerpc: Fix DSCR inheritance in copy_thread()
If the default DSCR is non zero we set thread.dscr_inherit in
copy_thread() meaning the new thread and all its children will ignore
future updates to the default DSCR. This is not intended and is
a change in behaviour that a number of our users have hit.
We just need to inherit thread.dscr and thread.dscr_inherit from
the parent which ends up being much simpler.
Anton Blanchard [Mon, 3 Sep 2012 16:48:46 +0000 (16:48 +0000)]
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
When we update the DSCR either via emulation of mtspr(DSCR) or via
a change to dscr_default in sysfs we don't update thread.dscr.
We will eventually update it at context switch time but there is
a period where thread.dscr is incorrect.
If we fork at this point we will copy the old value of thread.dscr
into the child. To avoid this, always keep thread.dscr in sync with
reality.
Anton Blanchard [Mon, 3 Sep 2012 16:47:56 +0000 (16:47 +0000)]
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
Writing to dscr_default in sysfs doesn't actually change the DSCR -
we rely on a context switch on each CPU to do the work. There is no
guarantee we will get a context switch in a reasonable amount of time
so fire off an IPI to force an immediate change.
This issue was found with the following test case:
Paul Mackerras [Thu, 26 Jul 2012 18:51:09 +0000 (18:51 +0000)]
powerpc/powernv: Always go into nap mode when CPU is offline
The CPU hotplug code for the powernv platform currently only puts
offline CPUs into nap mode if the powersave_nap variable is set.
However, HV-style KVM on this platform requires secondary CPU threads
to be offline and in nap mode. Since we know nap mode works just
fine on all POWER7 machines, and the only machines that support the
powernv platform are POWER7 machines, this changes the code to
always put offline CPUs into nap mode, regardless of powersave_nap.
Powersave_nap still controls whether or not CPUs go into nap mode
when idle, as before.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Thu, 26 Jul 2012 13:56:11 +0000 (13:56 +0000)]
powerpc: Give hypervisor decrementer interrupts their own handler
At the moment the handler for hypervisor decrementer interrupts is
the same as for decrementer interrupts, i.e. timer_interrupt().
This is bogus; if we ever do get a hypervisor decrementer interrupt
it won't have anything to do with the next timer event. In fact
the only time we get hypervisor decrementer interrupts is when one
is left pending on exit from a KVM guest.
When we get a hypervisor decrementer interrupt we don't need to do
anything special to clear it, since they are edge-triggered on the
transition of HDEC from 0 to -1. Thus this adds an empty handler
function for them. We don't need to have them masked when interrupts
are soft-disabled, so we use STD_EXCEPTION_HV instead of
MASKABLE_EXCEPTION_HV.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Walleij [Thu, 30 Aug 2012 17:22:36 +0000 (19:22 +0200)]
ARM: gemini: fix the gemini build
Test-compiling obscure machines I notice that the gemini (which
by the way lacks a defconfig) is broken since some time back.
Adding a simple missing include makes it build again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
[ 2.086181] Waiting for root device /dev/mmcblk0p1...
[ 2.324066] Unhandled fault: imprecise external abort (0x406) at 0x00000000
[ 2.331451] Internal error: : 406 [#1] ARM
[ 2.335784] Modules linked in:
[ 2.339050] CPU: 0 Not tainted (3.6.0-rc3 #60)
[ 2.344146] PC is at default_idle+0x28/0x30
[ 2.348602] LR is at trace_hardirqs_on_caller+0x15c/0x1b0
...
This turned out to be due to memory corruption caused by long-broken
PIO code in drivers/mmc/host/omap.c. (Previously, this driver had
been using DMA; but the above commit caused the MMC driver to fall
back to PIO mode with an unmodified Kconfig.)
The PIO code, added with the rest of the driver in commit 730c9b7e6630f786fcec026fb11d2e6f2c90fdcb ("[MMC] Add OMAP MMC host
driver"), confused bytes with 16-bit words. This bug caused memory
located after the PIO transfer buffer to be corrupted with transfers
larger than 32 bytes. The driver also did not increment the buffer
pointer after the transfer occurred. This bug resulted in data
corruption during any transfer larger than 64 bytes.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Ian Chen [Wed, 29 Aug 2012 06:05:36 +0000 (15:05 +0900)]
mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim. For these specific MoviNAND devices, we skip
these operations.
Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.
Doug Anderson [Wed, 25 Jul 2012 15:33:17 +0000 (08:33 -0700)]
mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
The documentation for the dw_mmc part says that the low power
mode should normally only be set for MMC and SD memory and should
be turned off for SDIO cards that need interrupts detected.
The best place I could find to do this is when the SDIO interrupt
was first enabled. I rely on the fact that dw_mci_setup_bus()
will be called when it's time to reenable.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Wed, 1 Aug 2012 00:30:46 +0000 (09:30 +0900)]
mmc: dw_mmc: fix error handling in PIO mode
Data transfer will be continued until all the bytes are transmitted,
even if data crc error occurs during a multiple-block data transfer.
This means RXDR/TXDR interrupts will occurs until data transfer is
terminated. Early setting of host->sg to NULL prevents going into
xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts
occurs. And checking error interrupt status in the xxx_data_pio functions
is no need because dw_mci_interrupt does do the same. This patch also
removes it.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Wed, 1 Aug 2012 00:30:40 +0000 (09:30 +0900)]
mmc: dw_mmc: correct mishandling error interrupt
Datasheet of SYNOPSYS mentions that DTO(Data Transfer Over) interrupt
will be raised even if some error interrupts, however it is actually
found that DTO does not occur. SYNOPSYS has confirmed this issue.
Current implementation defers the call of tasklet_schedule until DTO
when the error interrupts is happened. This patch fixes error handling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Wed, 1 Aug 2012 00:30:30 +0000 (09:30 +0900)]
mmc: dw_mmc: amend using error interrupt status
RINTSTS status includes masked interrupts as well as unmasked.
data_status and cmd_status are set by value of RINTSTS in interrupt handler
and tasklet finally uses it to decide whether error is happened or not.
In addition, MINTSTS status is used for setting data_status in PIO.
Masked error interrupt will not be handled and that status can be considered
non-error case.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed By: Girish K S <girish.shivananjappa@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: atmel-mci: not busy flag has also to be used for read operations
Even if the datasheet says that the not busy flag has to be used only
for write operations, it's false except for version lesser than v2xx.
Not waiting on the not busy flag for read operations can cause the
controller to hang-up during the initialization of some SD cards
with DMA after the first CMD6 -- the next command is sent too early.
Shawn Guo [Wed, 22 Aug 2012 15:10:01 +0000 (23:10 +0800)]
mmc: sdhci-esdhc: break out early if clock is 0
Since commit 30832ab56 ("mmc: sdhci: Always pass clock request value
zero to set_clock host op") was merged, esdhc_set_clock starts hitting
"if (clock == 0)" where ESDHC_SYSTEM_CONTROL has been operated. This
causes SDHCI card-detection function being broken. Fix the regression
by moving "if (clock == 0)" above ESDHC_SYSTEM_CONTROL operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
UBI was mistakingly using 'kfree()' instead of 'kmem_cache_free()' when
freeing "attach eraseblock" structures in vtbl.c. Thankfully, this happened
only when we were doing auto-format, so many systems were unaffected. However,
there are still many users affected.
It is strange, but the system did not crash and nothing bad happened when
the SLUB memory allocator was used. However, in case of SLOB we observed an
crash right away.
This problem was introduced in 2.6.39 by commit
"6c1e875 UBI: add slab cache for ubi_scan_leb objects"
A note for stable trees:
Because variable were renamed, this won't cleanly apply to older kernels.
Changing names like this should help:
1. ai -> si
2. aeb_slab_cache -> seb_slab_cache
3. new_aeb -> new_seb
Reported-by: Richard Genoud <richard.genoud@gmail.com> Tested-by: Richard Genoud <richard.genoud@gmail.com> Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Cc: stable@vger.kernel.org [v2.6.39+] Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
ARM: shmobile: armadillo800eva: enable rw rootfs mount
armadillo800eva default boot loader is "hermit",
and it's tag->u.core.flags has flag when kernel boots.
Because of this, ${LINUX}/arch/arm/kernel/setup.c :: parse_tag_core()
didn't remove MS_RDONLY flag from root_mountflags.
Thus, the rootfs is mounted as "readonly".
This patch adds "rw" kernel parameter,
and enable read/write mounts for rootfs
1) NLA_PUT* --> nla_put_* conversion got one case wrong in
nfnetlink_log, fix from Patrick McHardy.
2) Missed error return check in ipw2100 driver, from Julia Lawall.
3) PMTU updates in ipv4 were setting the expiry time incorrectly, fix
from Eric Dumazet.
4) SFC driver erroneously reversed src and dst when reporting filters
via ethtool.
5) Memory leak in CAN protocol and wrong setting of IRQF_SHARED in
sja1000 can platform driver, from Alexey Khoroshilov and Sven
Schmitt.
6) Fix multicast traffic scaling regression in ipv4_dst_destroy, only
take the lock when we really need to. From Eric Dumazet.
7) Fix non-root process spoofing in netlink, from Pablo Neira Ayuso.
8) CWND reduction in TCP is done incorrectly during non-SACK recovery,
fix from Yuchung Cheng.
9) Revert netpoll change, and fix what was actually a driver specific
problem. From Amerigo Wang. This should cure bootup hangs with
netconsole some people reported.
10) Fix xen-netfront invoking __skb_fill_page_desc() with a NULL page
pointer. From Ian Campbell.
11) SIP NAT fix for expectiontation creation, from Pablo Neira Ayuso.
12) __ip_rt_update_pmtu() needs RCU locking, from Eric Dumazet.
13) Fix usbnet deadlock on resume, can't use GFP_KERNEL in this
situation. From Oliver Neukum.
14) The davinci ethernet driver triggers an OOPS on removal because it
frees an MDIO object before unregistering it. Fix from Bin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
net: qmi_wwan: add several new Gobi devices
fddi: 64 bit bug in smt_add_para()
net: ethernet: fix kernel OOPS when remove davinci_mdio module
net/xfrm/xfrm_state.c: fix error return code
net: ipv6: fix error return code
net: qmi_wwan: new device: Foxconn/Novatel E396
usbnet: fix deadlock in resume
cs89x0 : packet reception not working
netfilter: nf_conntrack: fix racy timer handling with reliable events
bnx2x: Correct the ndo_poll_controller call
bnx2x: Move netif_napi_add to the open call
ipv4: must use rcu protection while calling fib_lookup
bnx2x: fix 57840_MF pci id
net: ipv4: ipmr_expire_timer causes crash when removing net namespace
e1000e: DoS while TSO enabled caused by link partner with small MSS
l2tp: avoid to use synchronize_rcu in tunnel free function
gianfar: fix default tx vlan offload feature flag
netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation
xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
netfilter: nfnetlink_log: fix error return code in init path
...
Henrik Rydberg [Sat, 1 Sep 2012 19:47:11 +0000 (21:47 +0200)]
HID: Only dump input if someone is listening
Going through the motions of printing the debug message information
takes a long time; using the keyboard can lead to a 160 us irqsoff
latency. This patch skips hid_dump_input() when there are no open
handles, which brings latency down to 100 us.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Gobi devices are composite, needing both the qcserial and
qmi_wwan drivers to support all functions. Re-syncing the
list of supported devices with qcserial.
Cc: Aleksander Morgado <aleksander@lanedo.com> Cc: Thomas Tuttle <ttuttle@chromium.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@tempietto.lan>
Dan Carpenter [Sat, 1 Sep 2012 09:57:40 +0000 (09:57 +0000)]
fddi: 64 bit bug in smt_add_para()
The intent was to set 4 bytes of data so that's why the sp_len is set
to 4 on the next line. The cast to u_long pointer clears 8 bytes
on 64 bit arches.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@tempietto.lan>
Guenter Roeck [Sat, 25 Aug 2012 00:25:01 +0000 (17:25 -0700)]
linux/kernel.h: Fix DIV_ROUND_CLOSEST to support negative dividends
DIV_ROUND_CLOSEST returns a bad result for negative dividends:
DIV_ROUND_CLOSEST(-2, 2) = 0
Most of the time this does not matter. However, in the hardware monitoring
subsystem, DIV_ROUND_CLOSEST is sometimes used on integers which can be
negative (such as temperatures).
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Jean Delvare <khali@linux-fr.org>
John Stultz [Fri, 31 Aug 2012 17:30:06 +0000 (13:30 -0400)]
time: Move ktime_t overflow checking into timespec_valid_strict
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b14526ca7 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is a set of two bug fixes. One is the ATOMIC problem which is
now causing a compile failure in certain situations. The other is
mishandling of PER_LINUX32 which may also cause user visible effects.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix personality flag check in copy_thread()
[PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of s390 bug fixes for 3.5-rc4"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/32: Don't clobber personality flags on exec
s390/smp: add missing smp_store_status() for !SMP
s390/dasd: fix ioctl return value
s390: Always use "long" for ssize_t to match size_t
projects / karo-tx-linux.git / log