Will Deacon [Tue, 22 Nov 2011 17:30:32 +0000 (17:30 +0000)]
ARM: LPAE: mark memory banks with start > ULONG_MAX as highmem
Memory banks living outside of the 32-bit physical address
space do not have a 1:1 pa <-> va mapping and therefore the
__va macro may wrap.
This patch ensures that such banks are marked as highmem so
that the Kernel doesn't try to split them up when it sees that
the wrapped virtual address overlaps the vmalloc space.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Nicolas Pitre <nico@linaro.org>
Catalin Marinas [Tue, 22 Nov 2011 17:30:32 +0000 (17:30 +0000)]
ARM: LPAE: Add identity mapping support for the 3-level page table format
With LPAE, the pgd is a separate page table with entries pointing to the
pmd. The identity_mapping_add() function needs to ensure that the pgd is
populated before populating the pmd level. The do..while blocks now loop
over the pmd in order to have the same implementation for the two page
table formats. The pmd_addr_end() definition has been removed and the
generic one used instead. The pmd clean-up is done in the pgd_free()
function.
Catalin Marinas [Tue, 22 Nov 2011 17:30:31 +0000 (17:30 +0000)]
ARM: LPAE: Add context switching support
With LPAE, TTBRx registers are 64-bit. The ASID is stored in TTBR0
rather than a separate Context ID register. This patch makes the
necessary changes to handle context switching on LPAE.
Catalin Marinas [Tue, 22 Nov 2011 17:30:31 +0000 (17:30 +0000)]
ARM: LPAE: Add fault handling support
The DFSR and IFSR register format is different when LPAE is enabled. In
addition, DFSR and IFSR have similar definitions for the fault type.
This modifies the fault code to correctly handle the new format.
Catalin Marinas [Tue, 22 Nov 2011 17:30:29 +0000 (17:30 +0000)]
ARM: LPAE: Invalidate the TLB before freeing the PMD
Similar to the PTE freeing, this patch introduced __pmd_free_tlb() which
invalidates the TLB before freeing a PMD page. This is needed because on
newer processors the entry in the upper page table may be cached by the
TLB and point to random data after the PMD has been freed.
Catalin Marinas [Tue, 22 Nov 2011 17:30:29 +0000 (17:30 +0000)]
ARM: LPAE: MMU setup for the 3-level page table format
This patch adds the MMU initialisation for the LPAE page table format.
The swapper_pg_dir size with LPAE is 5 rather than 4 pages. A new
proc-v7-3level.S file contains the TTB initialisation, context switch
and PTE setting code with the LPAE. The TTBRx split is based on the
PAGE_OFFSET with TTBR1 used for the kernel mappings. The 36-bit mappings
(supersections) and a few other memory types in mmu.c are conditionally
compiled.
Catalin Marinas [Tue, 22 Nov 2011 17:30:29 +0000 (17:30 +0000)]
ARM: LPAE: Page table maintenance for the 3-level format
This patch modifies the pgd/pmd/pte manipulation functions to support
the 3-level page table format. Since there is no need for an 'ext'
argument to cpu_set_pte_ext(), this patch conditionally defines a
different prototype for this function when CONFIG_ARM_LPAE.
The patch also introduces the L_PGD_SWAPPER flag to mark pgd entries
pointing to pmd tables pre-allocated in the swapper_pg_dir and avoid
trying to free them at run-time. This flag is 0 with the classic page
table format.
Catalin Marinas [Tue, 22 Nov 2011 17:30:29 +0000 (17:30 +0000)]
ARM: LPAE: Introduce the 3-level page table format definitions
This patch introduces the pgtable-3level*.h files with definitions
specific to the LPAE page table format (3 levels of page tables).
Each table is 4KB and has 512 64-bit entries. An entry can point to a
40-bit physical address. The young, write and exec software bits share
the corresponding hardware bits (negated). Other software bits use spare
bits in the PTE.
The patch also changes some variable types from unsigned long or int to
pteval_t or pgprot_t.
Will Deacon [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: LPAE: add ISBs around MMU enabling code
Before we enable the MMU, we must ensure that the TTBR registers contain
sane values. After the MMU has been enabled, we jump to the *virtual*
address of the following function, so we also need to ensure that the
SCTLR write has taken effect.
This patch adds ISB instructions around the SCTLR write to ensure the
visibility of the above.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: LPAE: Factor out classic-MMU specific code into proc-v7-2level.S
This patch modifies the proc-v7.S file so that it only contains code
shared between classic MMU and LPAE. The non-common code is factored out
into a separate file.
Catalin Marinas [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: LPAE: Move the FSR definitions to separate files
The FSR structure is different with LPAE and this patch moves the
classic MMU specific definition to a separate fsr-2level.c file that is
included in fault.c. It also moves the fsr_fs and FSR bits to the
fault.h file.
Catalin Marinas [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: LPAE: Move page table maintenance macros to pgtable-2level.h
The page table maintenance macros need to be duplicated between the
classic and the LPAE MMU so this patch moves those that are not common
to the pgtable-2level.h file.
Russell King [Tue, 22 Nov 2011 17:30:28 +0000 (17:30 +0000)]
ARM: pgtable: switch to use pgtable-nopud.h
Nick Piggin noted upon introducing 4level-fixup.h:
| Add a temporary "fallback" header so architectures can run with
| the 4level pagetables patch without modification. All architectures
| should be converted to use the folding headers (include/asm-generic/
| pgtable-nop?d.h) as soon as possible, and the fallback header removed.
This makes ARM compliant with this statement.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Tue, 22 Nov 2011 17:30:27 +0000 (17:30 +0000)]
ARM: pgtable: Fix compiler warning in ioremap.c introduced by nopud
With the arch/arm code conversion to pgtable-nopud.h, the section and
supersection (un|re)map code triggers compiler warnings on UP systems.
This is caused by pmd_offset() being given a pgd_t argument rather than
a pud_t one. This patch makes the necessary conversion with the
assumption that the pud is folded into the pgd. The page table setting
code only loops over the pmd which is enough with the classic page
tables. This code is not compiled when LPAE is enabled.
Tony Lindgren [Tue, 6 Dec 2011 16:50:42 +0000 (17:50 +0100)]
ARM: 7194/1: OMAP: Fix build after a merge between v3.2-rc4 and ARM restart changes
ARM restart changes needed changes to common.h to make it local.
This conflicted with v3.2-rc4 DSS related hwmod changes that
git mergetool was not able to handle.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Wed, 23 Nov 2011 12:26:25 +0000 (12:26 +0000)]
ARM: SMP: use idmap_pgd for mapping MMU enable during secondary booting
The ARM SMP booting code allocates a temporary set of page tables
containing an identity mapping of the kernel image and provides this
to secondary CPUs for initial booting.
In reality, we only need to include the __turn_mmu_on function in the
identity mapping since the rest of the kernel is executing from virtual
addresses after this point.
This patch adds __turn_mmu_on to the .idmap.text section, allowing the
SMP booting code to use the idmap_pgd directly and not have to populate
its own set of page table.
As a result of this patch, we can make the identity_mapping_add function
static (since it is only used within mm/idmap.c) and also remove the
identity_mapping_del function. The identity map population is moved to
an early initcall so that it is setup in time for secondary CPU bringup.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Wed, 23 Nov 2011 12:03:27 +0000 (12:03 +0000)]
ARM: head.S: only include __turn_mmu_on in the initial identity mapping
__create_page_tables identity maps the region of memory from
__enable_mmu to the end of __turn_mmu_on.
In preparation for including __turn_mmu_on in the .idmap.text section,
this patch modifies the identity mapping so that it only includes the
__turn_mmu_on code.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Wed, 8 Jun 2011 14:53:34 +0000 (15:53 +0100)]
ARM: idmap: use idmap_pgd when setting up mm for reboot
For soft-rebooting a system, it is necessary to map the MMU-off code
with an identity mapping so that execution can continue safely once the
MMU has been switched off.
Currently, switch_mm_for_reboot takes out a 1:1 mapping from 0x0 to
TASK_SIZE during reboot in the hope that the reset code lives at a
physical address corresponding to a userspace virtual address.
This patch modifies the code so that we switch to the idmap_pgd tables,
which contain a 1:1 mapping of the cpu_reset code. This has the
advantage of only remapping the code that we need and also means we
don't need to worry about allocating a pgd from an atomic context in the
case that the physical address of the cpu_reset code aliases with the
virtual space used by the kernel.
Acked-by: Dave Martin <dave.martin@linaro.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Tue, 15 Nov 2011 11:11:19 +0000 (11:11 +0000)]
ARM: suspend: use idmap_pgd instead of suspend_pgd
The ARM CPU suspend code requires cpu_resume_mmu to be identity mapped
in order to re-enable the MMU when coming out of suspend. Currently,
this is accomplished by maintaining a suspend_pgd with the relevant
mapping put in place at init time.
This patch replaces the use of suspend_pgd with the new idmap_pgd.
cpu_resume_mmu is placed in the .idmap.text section so that it is
included in the identity map.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Dave Martin <dave.martin@linaro.org> Tested-by: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Fri, 30 Sep 2011 10:43:29 +0000 (11:43 +0100)]
ARM: idmap: populate identity map pgd at init time using .init.text
When disabling and re-enabling the MMU, it is necessary to take out an
identity mapping for the code that manipulates the SCTLR in order to
avoid it disappearing from under our feet. This is useful when soft
rebooting and returning from CPU suspend.
This patch allocates a set of page tables during boot and populates them
with an identity mapping for the .idmap.text section. This means that
users of the identity map do not need to manage their own pgd and can
instead annotate their functions with __idmap or, in the case of assembly
code, place them in the correct section.
Acked-by: Dave Martin <dave.martin@linaro.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Russell King [Tue, 6 Dec 2011 12:57:02 +0000 (12:57 +0000)]
ARM: restart: Temporary #error to persuade platform maintainers to take the restart changes seriously
Force builds to fail to ensure that platform maintainers take the
restart changes seriously, and sort out fixing their code before the
next merge window.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Fri, 2 Dec 2011 17:16:01 +0000 (18:16 +0100)]
ARM: 7185/1: perf: don't assign platform_device on unsupported CPUs
In the unlikely case that a platform registers a PMU platform_device
when running on a CPU that is unsupported by perf, we will encounter a
NULL dereference when trying to assign the platform_device to the
cpu_pmu structure.
This patch checks that the CPU is supported by perf before assigning
the platform_device.
Reported-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tony Lindgren [Tue, 6 Dec 2011 04:45:37 +0000 (05:45 +0100)]
ARM: 7192/1: OMAP: Fix build error for omap1_defconfig
Otherwise we get the following error:
In function 'omap_init_consistent_dma_size':
error: implicit declaration of function 'init_consistent_dma_size'
Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The linker places the unwind tables in readonly sections. So when using
an XIP kernel these are located in ROM and cannot be modified.
For that reason the current approach to convert the relative offsets in
the unwind index to absolute addresses early in the boot process doesn't
work with XIP.
The offsets in the unwind index section are signed 31 bit numbers and
the structs are sorted by this offset. So it first has offsets between
0x40000000 and 0x7fffffff (i.e. the negative offsets) and then offsets
between 0x00000000 and 0x3fffffff. When seperating these two blocks the
numbers are sorted even when interpreting the offsets as unsigned longs.
So determine the first non-negative entry once and track that using the
new origin pointer. The actual bisection can then use a plain unsigned
long comparison. The only thing that makes the new bisection more
complicated is that the offsets are relative to their position in the
index section, so the key to search needs to be adapted accordingly in
each step.
Moreover several consts are added to catch future writes and rename the
member "addr" of struct unwind_idx to "addr_offset" to better match the
new semantic. (This has the additional benefit of breaking eventual
users at compile time to make them aware of the change.)
In my tests the new algorithm was a tad faster than the original and has
the additional upside of not needing the initial conversion and so saves
some boot time and it's possible to unwind even earlier.
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Nicolas Pitre [Fri, 2 Dec 2011 22:09:42 +0000 (23:09 +0100)]
ARM: 7186/1: fix Kconfig issue with PHYS_OFFSET and !MMU
Commit 1b9f95f8ade9 (ARM: prepare for removal of a bunch of <mach/memory.h>
files) introduced CONFIG_PHYS_OFFSET but the Kconfig hex prompt did not
provide a default value.
This has the undesired side effect of breaking a reportedly used
trick for updating defconfigs on the fly for routine buildtesting
across all arch and all platforms, i.e.
cp /path/to/somedefconfig .config ; yes "" | make oldconfig
because the config system will endlessly loop until a valid address is
provided.
However we can't just pick a random default value since it is likely to
be wrong for the majority of the boards as the right answer for this
option is quite varied. So the fact that the config system insists on
having a proper value be entered is actually a good thing.
It turns out that only at91x40_defconfig has this problem because it has
CONFIG_MMU=n. However, in the !MMU case, there is already a CONFIG_DRAM_BASE
value that can be used here. So let's use that as a default in that case
and suppress the redundant CONFIG_PHYS_OFFSET prompt.
Eventually the DRAM_BASE config option could simply be replaced by
PHYS_OFFSET directly, but that's a larger change better suited for later.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Nicolas Pitre <nico@linaro.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to ARM.
Without these changes, my ARM board encounters many hang and livelock
scenarios.
After applying this patch, OOM feature performance improves according to
my testing.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Thu, 24 Nov 2011 11:23:18 +0000 (12:23 +0100)]
ARM: 7173/1: Add optimised swahb32() byteswap helper for v6 and above
ARMv6 and later processors have the REV16 instruction, which swaps
the bytes within each halfword of a register value.
This is already used to implement swab16(), but since the native
operation performaed by REV16 is actually swahb32(), this patch
renames the existing swab16() helper accordingly and defines
__arch_swab16() in terms of it. This allows calls to both swab16()
and swahb32() to be optimised.
The compiler's generated code might improve someday, but as of
4.5.2 the code generated for pure C implementing these 16-bit
bytesswaps remains pessimal.
swahb32() is useful for converting 32-bit Thumb instructions
between integer and memory representation on BE8 platforms (among
other uses).
Signed-off-by: Dave Martin <dave.martin@linaro.org> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rob Herring [Tue, 22 Nov 2011 03:01:07 +0000 (04:01 +0100)]
ARM: 7169/1: topdown mmap support
Similar to other architectures, this adds topdown mmap support in user
process address space allocation policy. This allows mmap sizes greater
than 2GB. This support is largely copied from MIPS and the generic
implementations.
The address space randomization is moved into arch_pick_mmap_layout.
Tested on V-Express with ubuntu and a mmap test from here:
https://bugs.launchpad.net/bugs/861296
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 7193/1: Fix machine_is_xxx() naming for eSata SheevaPlug and QNAP TS-209
The eSata SheevaPlug and QNAP TS-209 devices were removed from
mach-types due to naming mismatches between machine_is_xxx(), CONFIG_XXX
and MACH_TYPE_XXX.
This patch fixes those mismatches and adds the devices back into
mach-types.
Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Jon Medhurst <tixy@yxit.co.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kevin Hilman [Tue, 25 Oct 2011 11:42:33 +0000 (12:42 +0100)]
ARM: 7140/1: remove NR_IRQS dependency for ARM-specific HARDIRQ_BITS definition
As a first step towards removing NR_IRQS, remove the ARM customization
of HARDIRQ_BITS based on NR_IRQS.
The generic code in <linux/hardirq.h> already has a default value of
10 for HARDIRQ_BITS which is the max used on ARM, so let's just remove
the NR_IRQS based customization and use the generic default.
Signed-off-by: Kevin Hilman <khilman@ti.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Tue, 6 Dec 2011 00:54:15 +0000 (16:54 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intr_remapping: Fix section mismatch in ir_dev_scope_init()
intel-iommu: Fix section mismatch in dmar_parse_rmrr_atsr_dev()
x86, amd: Fix up numa_node information for AMD CPU family 15h model 0-0fh northbridge functions
x86, AMD: Correct align_va_addr documentation
x86/rtc, mrst: Don't register a platform RTC device for for Intel MID platforms
x86/mrst: Battery fixes
x86/paravirt: PTE updates in k(un)map_atomic need to be synchronous, regardless of lazy_mmu mode
x86: Fix "Acer Aspire 1" reboot hang
x86/mtrr: Resolve inconsistency with Intel processor manual
x86: Document rdmsr_safe restrictions
x86, microcode: Fix the failure path of microcode update driver init code
Add TAINT_FIRMWARE_WORKAROUND on MTRR fixup
x86/mpparse: Account for bus types other than ISA and PCI
x86, mrst: Change the pmic_gpio device type to IPC
mrst: Added some platform data for the SFI translations
x86,mrst: Power control commands update
x86/reboot: Blacklist Dell OptiPlex 990 known to require PCI reboot
x86, UV: Fix UV2 hub part number
x86: Add user_mode_vm check in stack_overflow_check
Linus Torvalds [Tue, 6 Dec 2011 00:54:00 +0000 (16:54 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix loss of notification with multi-event
perf, x86: Force IBS LVT offset assignment for family 10h
perf, x86: Disable PEBS on SandyBridge chips
trace_events_filter: Use rcu_assign_pointer() when setting ftrace_event_call->filter
perf session: Fix crash with invalid CPU list
perf python: Fix undefined symbol problem
perf/x86: Enable raw event access to Intel offcore events
perf: Don't use -ENOSPC for out of PMU resources
perf: Do not set task_ctx pointer in cpuctx if there are no events in the context
perf/x86: Fix PEBS instruction unwind
oprofile, x86: Fix crash when unloading module (nmi timer mode)
oprofile: Fix crash when unloading module (hr timer mode)
Linus Torvalds [Tue, 6 Dec 2011 00:53:43 +0000 (16:53 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Set noop handler in clockevents_exchange_device()
tick-broadcast: Stop active broadcast device when replacing it
clocksource: Fix bug with max_deferment margin calculation
rtc: Fix some bugs that allowed accumulating time drift in suspend/resume
rtc: Disable the alarm in the hardware
Linus Torvalds [Tue, 6 Dec 2011 00:50:24 +0000 (16:50 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched, x86: Avoid unnecessary overflow in sched_clock
sched: Fix buglet in return_cfs_rq_runtime()
sched: Avoid SMT siblings in select_idle_sibling() if possible
sched: Set the command name of the idle tasks in SMP kernels
sched, rt: Provide means of disabling cross-cpu bandwidth sharing
sched: Document wait_for_completion_*() return values
sched_fair: Fix a typo in the comment describing update_sd_lb_stats
sched: Add a comment to effective_load() since it's a pain
Russell King [Sat, 5 Nov 2011 21:30:00 +0000 (21:30 +0000)]
ARM: restart: remove the now empty arch_reset()
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 5 Nov 2011 12:36:40 +0000 (12:36 +0000)]
ARM: restart: remove comments about adding code to arch_reset()
arch_reset() is deprecated; systems should hook into system restart via
the 'restart' method in the platforms machine description record.
Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Mon, 5 Dec 2011 23:35:16 +0000 (15:35 -0800)]
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] ap: Setup timer for sending messages after reset.
[S390] cio: fix chsc_chp_vary
[S390] cio: provide fake irb for transport mode IO
[S390] cio: disallow driver io for known to be broken paths
[S390] hibernate: directly trigger subchannel evaluation
[S390] remove reset of system call restart on psw changes
[S390] add missing .set function for NT_S390_LAST_BREAK regset
[S390] fix page change underindication in pgste_update_all
[S390] ptrace inferior call interactions with TIF_SYSCALL
[S390] kdump: Replace is_kdump_kernel() with OLDMEM_BASE check
intr_remapping: Fix section mismatch in ir_dev_scope_init()
Fix:
Section mismatch in reference from the function
ir_dev_scope_init() to the function
.init.text:dmar_dev_scope_init() The function
ir_dev_scope_init() references the function __init dmar_dev_scope_init().
intel-iommu: Fix section mismatch in dmar_parse_rmrr_atsr_dev()
dmar_parse_rmrr_atsr_dev() calls rmrr_parse_dev() and
atsr_parse_dev() which are both marked as __init.
Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
x86, amd: Fix up numa_node information for AMD CPU family 15h model 0-0fh northbridge functions
I've received complaints that the numa_node attribute for family
15h model 00-0fh (e.g. Interlagos) northbridge functions shows
-1 instead of the proper node ID.
Correct this with attached quirks (similar to quirks for other
AMD CPU families used in multi-socket systems).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Frank Arnold <frank.arnold@amd.com> Cc: Borislav Petkov <borislav.petkov@amd.com> Link: http://lkml.kernel.org/r/20111202072143.GA31916@alberich.amd.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
Borislav Petkov [Mon, 21 Nov 2011 11:10:19 +0000 (12:10 +0100)]
x86, AMD: Correct align_va_addr documentation
Commit dfb09f9b7ab0 ("x86, amd: Avoid cache aliasing penalties
on AMD family 15h") introduced a kernel command line parameter
called 'align_va_addr' which still refers to arguments used in
an earlier version of the patch and which got changed without
updating the documentation. Correct that omission.
The problem is that in copy_page_range() we turn lazy mode on,
and then in swap_entry_free() we call swap_count_continued()
which ends up in:
map = kmap_atomic(page, KM_USER0) + offset;
and then later we touch *map.
Since we are running in batched mode (lazy) we don't actually
set up the PTE mappings and the kmap_atomic is not done
synchronously and ends up trying to dereference a page that has
not been set.
Looking at kmap_atomic_prot_pfn(), it uses
'arch_flush_lazy_mmu_mode' and doing the same in
kmap_atomic_prot() and __kunmap_atomic() makes the problem go
away.
Interestingly, commit b8bcfe997e4615 ("x86/paravirt: remove lazy
mode in interrupts") removed part of this to fix an interrupt
issue - but it went to far and did not consider this scenario.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Chubb [Mon, 5 Dec 2011 13:53:53 +0000 (16:53 +0300)]
x86: Fix "Acer Aspire 1" reboot hang
Looks like on some Acer Aspire 1s with older bioses, reboot via bios
fails. It works on my machine, (with BIOS version 0.3310) but
not on some others (BIOS version 0.3309).
There's a log of problems at:
https://bbs.archlinux.org/viewtopic.php?id=124136
This patch adds a different callback to the reboot quirk table,
to allow rebooting via keybaord controller.
Reported-by: Uroš Vampl <mobile.leecher@gmail.com> Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au> Cc: Don Zickus <dzickus@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: stable@kernel.org Link: http://lkml.kernel.org/r/1323093233-9481-1-git-send-email-anarsoul@gmail.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86/mtrr: Resolve inconsistency with Intel processor manual
Following is from Notes of section 11.5.3 of Intel processor
manual available at:
http://www.intel.com/Assets/PDF/manual/325384.pdf
For the Pentium 4 and Intel Xeon processors, after the sequence of
steps given above has been executed, the cache lines containing the
code between the end of the WBINVD instruction and before the
MTRRS have actually been disabled may be retained in the cache
hierarchy. Here, to remove code from the cache completely, a
second WBINVD instruction must be executed after the MTRRs have
been disabled.
This patch provides resolution for that.
Ideally, I will like to make changes only for Pentium 4 and Xeon
processors. But, I am not finding easier way to do it.
And, extra wbinvd() instruction does not hurt much for other
processors.
Signed-off-by: Ajaykumar Hotchandani <ajaykumar.hotchandani@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Link: http://lkml.kernel.org/r/4EBD1CC5.3030008@oracle.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
projects / karo-tx-linux.git / log