Avinash Patil [Sat, 23 Mar 2013 04:49:06 +0000 (21:49 -0700)]
mwifiex: avoid waking up device in awake state
We have received interrupt from device means FW is not sleeping.
In this case make sure wakeup handler for PCIe is not invoked by
setting adapter->pm_wakeup_fw_try to false.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi [Fri, 22 Mar 2013 11:58:23 +0000 (12:58 +0100)]
ath9k: trivial: change spectral relayfs buffering
The spectral data provided via relay-fs introduces a buffering
latency given by the subbuf_size. To meet the requirements for
delay-sensitive applications (like real-time spectral plotter),
reduce subbuf_size and increase n_subbufs.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Thu, 21 Mar 2013 19:28:40 +0000 (20:28 +0100)]
b43: remove warning for LP-PHY with sprom < 8
The BCM5354 SoC has a build in ieee80211 core rev 13 with a LP-PHY on
it. This devices has a sprom version 3 stored in the nvram. This patch
removes the warning and uses the opo values from the sprom as mentioned
in the specs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, default VHT configuration from the firmware is used
for the VHT operations. Adding vhtcfg command to configure the
firmware based on input received from cfg.
Enable VHT for AP mode only when cfg80211_ap_settings has a
VHT IE i.e., when ieee80211ac is set to 1 in the hostapd.conf.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 8 Mar 2013 07:41:53 +0000 (09:41 +0200)]
wlcore: move handling from hardirq to the irq thread function
Spin locks and completions are expensive in hard IRQ context and cause
problems with RT kernels. In RT kernels, both spin locks and
completions can schedule(), so we can't use them in hard irq context.
Move handling code into the irq thread function to avoid that.
Luciano Coelho [Tue, 12 Mar 2013 15:04:01 +0000 (17:04 +0200)]
wlcore: use print_hex_dump_debug()
We were printing out all the hex dumps regardless of whether dynamic
debugging was enabled or not. Now that print_hex_dump_debug() has
been implemented, we can use that instead.
Arik Nemtsov [Tue, 12 Mar 2013 15:19:46 +0000 (17:19 +0200)]
wlcore: consider dummy packets when tx queues are empty
Don't ignore dummy packets when our queues are empty. This causes dummy
packets never to be sent when traffic is not suspended by FW thresholds,
which happens only in high Tx throughput situations. This may hurt Rx
performance.
Arik Nemtsov [Tue, 12 Mar 2013 15:19:45 +0000 (17:19 +0200)]
wlcore: correctly check state before regdomain conf
The wlcore state was checked without the mutex being taken. This leads
to WARN_ONs sometimes if a notification arrives when the driver
is on, but the mutex is only taken after it is off. This usually
happens if stopping the driver while connected to a network.
Arik Nemtsov [Tue, 12 Mar 2013 15:19:44 +0000 (17:19 +0200)]
wlcore: AP-mode - recover security seq num for stations
Save the sequence number of the broadcast AP link in the wlvif. For each
connected station, save the sequence number in the drv_priv part of
ieee80211_sta. Use the saved numbers on recovery/resume, with the
obligatory increment on recovery.
Arik Nemtsov [Tue, 12 Mar 2013 15:19:43 +0000 (17:19 +0200)]
wlcore: free AP global links properly on recovery
Dont use free_sta() on AP global links. It would fail an internal check
within the function and various structures within the link struct would
not be reset.
Eyal Shapira [Tue, 12 Mar 2013 15:19:41 +0000 (17:19 +0200)]
wlcore: don't attempt to roam in case of p2p
For STA we report beacon loss to higher levels so that wpa_s
can attempt to roam without disconnecting. In case of P2P CLI
we don't want to attempt roaming and instead disconnect immediately
upon beacon loss.
Nadim Zubidat [Tue, 12 Mar 2013 15:19:39 +0000 (17:19 +0200)]
wlcore: report rssi from roaming statistics
report the average beacon rssi which is calculated
by firmware for roaming statistics instead of the
last rx packet rssi. this results a more accurate
rssi reporting
Arik Nemtsov [Tue, 12 Mar 2013 15:19:38 +0000 (17:19 +0200)]
wlcore: consolidate tx_seq handling on recovery
Accumulate the total number of sent packets per-link to find out how far
the encryption sequence number has progressed. Use this number as the
initial security sequence number after recovery.
This consolidates security sequence handling for both chip families, as
we no longer have to rely on 12xx specific Tx completion.
A fortunate side effect of this is correct management of seq numbers for
AP roles and multi-role scenarios.
When a link is removed we save the last seq number on a persistent part
of the wlvif. This helps the data survive through recoveries/suspends,
which also entail changes in the hlid of the link.
Arik Nemtsov [Tue, 12 Mar 2013 15:19:36 +0000 (17:19 +0200)]
wlcore: fix link count in single-link-PSM optimization
commit 144614f3eebd7d only allowed a single active link when
turning on the optimization, ignoring the fact that an AP has two
additional global links.
Use 3 links as an indication for a single active link. Use the
FW PSM bits to verify the extra active link belongs to the AP role.
It is requiered to enter sleep mode with smaller delay in forced PS mode.
This fixes issue of testing force PS mode during VoIP traffic where packets
are sent every 20ms. Chip never enters ps mode with default 30 ms delay
in such test.
Signed-off-by: Igal Chernobelsky <igalc@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
Ilan Peer [Wed, 20 Feb 2013 06:41:54 +0000 (08:41 +0200)]
iwlwifi: mvm: Increase the max remain on channel time
Increase the maximal remain on channel time as longer remain
on channel requests are handled by the FW using fragmented
time events.
This reduces the number of user/kernel space iterations during
flows such as p2p_listen. In addition it is currently required
for flows which require longer duration such as p2p_sd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 20 Mar 2013 09:40:05 +0000 (10:40 +0100)]
iwlwifi: mvm: fix WoWLAN RF-kill bug
The RF-kill wakeup trigger flag is set in the wrong command,
which means it won't work. Also fix the comment in the TCP
wakeup trigger code -- the firmware was changed to look at
all the different trigger flags.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
5ghz_disable has no effect any longer, that was changed during
refactoring of EEPROM reading/parsing. Remove it, wpa_supplicant
allow now to specify frequencies, on which device will operate.
Ilan Peer [Wed, 13 Mar 2013 12:52:04 +0000 (14:52 +0200)]
iwlwifi: mvm: Fix quota handling for monitor interface
1. Quota for the monitor interface should be added only if there is
a channel context assigned to the interface.
2. In the unassign channel context flow, need to remove the quota
for the monitor interface binding, before unbinding.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The masks were wrong. They should be 0xffffffff when SCO,
HID or SNIFF profiles are used. They should be 0xffff0000
in any other case (default) to get a bit more throughput
when the BT profile allows for it.
Fix a debug print on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 20 Mar 2013 13:05:52 +0000 (14:05 +0100)]
cfg80211: fix potential connection work crash
If wpa_supplicant and iw/iwconfig are used together, very
rarely the system crashes. It seems to be related to the
connection parameters not being set up, but it's not all
clear to me how this happens. In any case, checking that
the conn pointer exists here is probably a good idea.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kalle Valo [Tue, 19 Mar 2013 13:25:20 +0000 (15:25 +0200)]
ath6kl: fix size_t printf warnings
My new tracing code for ath6kl introduced these warnings on 64-bit:
trace.h:38:1: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'size_t' [-Wformat]
trace.h:61:1: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'size_t' [-Wformat]
trace.h:84:1: warning: format '%d' expects argument of type 'int',
but argument 6 has type 'size_t' [-Wformat]
trace.h:119:1: warning: format '%d' expects argument of type 'int',
but argument 7 has type 'size_t' [-Wformat]
trace.h:173:1: warning: format '%d' expects argument of type 'int',
but argument 3 has type 'size_t' [-Wformat]
trace.h:193:1: warning: format '%d' expects argument of type 'int',
but argument 5 has type 'size_t' [-Wformat]
trace.h:221:1: warning: format '%d' expects argument of type 'int',
but argument 5 has type 'size_t' [-Wformat]
Fix them by using %zd.
Reported-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 6 Mar 2013 12:15:21 +0000 (13:15 +0100)]
iwlwifi: mvm: suppress key error messages in AP mode
In AP mode, don't attempt to program GTKs into the
device, they're used for TX only so not needed and
programming them causes error messages. Also, in
this case and if key programming fails, avoid trying
to remove the key that isn't present later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Helmut Schaa [Fri, 15 Mar 2013 08:57:57 +0000 (09:57 +0100)]
rt2x00: Fix tx status reporting for reordered frames in rt2800pci
rt2800 hardware sometimes reorders tx frames when transmitting to
multiple BA enabled STAs concurrently.
For example a tx queue
[ STA1 | STA2 | STA1 | STA2 ]
can result in the tx status reports
[ STA1 | STA1 | STA2 | STA2 ]
when the hw decides to put the frames for STA1 in one AMPDU.
To mitigate this effect associate the currently processed tx status
to the first frame in the tx queue with a matching wcid.
This patch fixes several problems related to incorrect tx status
reporting. Furthermore the tx rate selection is much more stable when
communicating with multiple STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware returned VHT cap has the same format that cfg80211
expects. There is no need to parse the vht cap from the firmware
and then set it to ieee80211_sta_vht_cap. Just copying is
sufficient.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 13 Feb 2013 11:25:28 +0000 (12:25 +0100)]
mac80211: stop queues temporarily for flushing
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 13 Feb 2013 11:11:00 +0000 (12:11 +0100)]
mac80211: pass queue bitmap to flush operation
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 16 Mar 2013 16:00:27 +0000 (17:00 +0100)]
mac80211/minstrel_ht: do not sample actively used rates
max_tp_rate2 and max_prob_rate tend to get used occasionally during
retransmission, which is more useful for the statistics than probing
with individual probe packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 16 Mar 2013 16:00:26 +0000 (17:00 +0100)]
mac80211/minstrel_ht: avoid useless sampling of high-probability slower rates
Slow rates that have >95% success probability do not need to be
monitored continuously. When the channel conditions change rapidly, the
slow sampling results are useless anyway. When conditions change slowly,
they will be monitored by gradual downgrading of the actively used
rates. This patch slightly improves throughput under good conditions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Under load, otherwise stable rates can easily fluctuate because of
collisions. In my tests on a clean channel, the success probability of
the max throughput rate often stays somewhere between 90% and 100% under
load. This can cause some unnecessary switching to lower rates.
This patch improves stability by treating success probability values
between 90% and 100% the same.
In my tests on a 3x3 HT20 link with lots of TCP traffic, it improves the
average throughput by a few mbit/s.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is need create driver own per interface debugfs files. This is
currently done by drv_{add,remove}_interface_debugfs() callbacks. But it
is possible that after we remove interface from the driver (i.e.
on suspend) we call drv_remove_interface_debugfs() function. Fixing this
problem will require to add call drv_{add,remove}_interface_debugfs()
anytime we create and remove interface in mac80211. So it's better to
add debugfs dir dentry to vif structure to allow to create/remove
custom debugfs driver files on drv_{add,remove}_interface().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only valid mgmt response to these pairing related commands is a
mgmt_cmd_complete and the returned parameters should contain the address
and address type of the remote device.
Johan Hedberg [Fri, 15 Mar 2013 22:07:15 +0000 (17:07 -0500)]
Bluetooth: Simplify address parameters of user_pairing_resp()
Instead of passing the bdaddr and bdaddr_type as separate parameters to
user_pairing_resp it's simpler to just pass the original mgmt_addr_info
struct which contains both values.
Johan Hedberg [Fri, 15 Mar 2013 22:07:14 +0000 (17:07 -0500)]
Bluetooth: Fix fast connectable state when enabling page scan
When powering on or enabling page scan we need to ensure that the page
scan parameters are as they should be. This is because some controllers
do not properly reset these values upon HCI_Reset. Since the
write_scan_parameters function is now called from several new places it
also checks for the >= 1.2 HCI version requirement before sending the
commands.
projects / linux-beck.git / log