Jerry Huang [Wed, 2 Nov 2011 01:16:44 +0000 (09:16 +0800)]
powerpc/85xx: Set max alloc length to 10MB on P1022DS
In order to support 1920x01080 resolution, we must increase the alloc
length.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> CC: Anatolij Gustschin <agust@denx.de> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jerry Huang [Thu, 3 Nov 2011 07:18:06 +0000 (15:18 +0800)]
powerpc/mpc85xx: Set SYSCLK to the required frequency
For ICS307-02, there is one general expression to generate SYSCLK:
CLK1Frequency = InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD)
If we want the required frequency for SYSCLK, we must find one solution
to generate this frequency, this solution includes VDW, RDW and OD.
For OD, there are only eight option value: 10, 2, 8, 4, 5, 7, 3, 6.
For RDW, the range is 1 to 127.
For VDW, the range is 4 to 511.
First, we use one OD, RDW and required SYSCLK to calculate the VDW,
if VDW is in it's range, we will calculate the CLK1Frequency with
the OD, RDW and VDW calculated, and we will check this percent
(CLK1Frequency / required SYSCLK), and the precision is 1/1000.
if the percent is less than 1/1000, we think the CLK1Frequency is we want.
Otherwise, We will continue to calculate it with the next OD and RDW.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 9 Nov 2011 15:10:49 +0000 (09:10 -0600)]
powerpc/85xx: Fix NAND SPL support
We cause CCSRBAR to be relocated in the SPL phase of NAND boot which
isn't expected and breaks things. Fixing the board config.h to NOT
relocate CCSR during the CONFIG_NAND_SPL phase.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 1 Nov 2011 03:13:26 +0000 (22:13 -0500)]
powerpc/85xx: Add support for Book-E MMU Arch v2.0
A few of the config registers changed definition between MMU v1.0 and
MMUv2.0. The new e6500 core from Freescale implements v2.0 of the
architecture.
Specifically, how we determine the size of TLB entries we support in the
variable size (or TLBCAM/TLB1) array is specified in a new register
(TLBnPS - TLB n Page size) instead of via TLBnCFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ramneek Mehresh [Tue, 8 Nov 2011 07:39:20 +0000 (13:09 +0530)]
powerpc/85xx: Fix warning for USB device-fixup
Fix USB device-fixup warning "node not found". This was occuring
because of static nature of start_offset variable
Static start_offset was storing offset of last node modified, and
was becoming issue if node fixup is carried multiple times,
resulting in "node not found" warning
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 18:30:45 +0000 (13:30 -0500)]
powerpc/85xx: resize the boot page TLB before relocating CCSR
On some Freescale systems (e.g. those booted from the on-chip ROM), the
TLB that covers the boot page can also cover CCSR, which breaks the CCSR
relocation code. To fix this, we resize the boot page TLB so that it only
covers the 4KB boot page.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 18:30:44 +0000 (13:30 -0500)]
powerpc/85xx: verify the current address of CCSR before relocating it
Verify that CCSR is actually located where it is supposed to be before
we relocate it. This is useful in detecting U-Boot configurations that
are broken (e.g. an incorrect value for CONFIG_SYS_CCSRBAR_DEFAULT).
If the current value is wrong, we enter an infinite loop, which is handy
for debuggers.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 18:30:41 +0000 (13:30 -0500)]
powerpc/85xx: fix definition of MAS register macros
Some of the MAS register macros do not protect the parameter with
parentheses, which could cause wrong values if the parameter includes
operators.
Also fix the definition of TSIZE_TO_BYTES() so that it actually uses
the parameter. This hasn't caused any problems to date because the
parameter was always been 'tsize'.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board_eth_init(). PCIe network card is also supported.
Put RGMII init after tsec_eth_init().
Skip initializing eTSEC3 and eTSEC4 with Carrier boards prior to ver 1.3.
chenhui zhao [Mon, 3 Oct 2011 13:38:50 +0000 (08:38 -0500)]
powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.
Signed-off-by: Gong Chen <g.chen@freescale.com> Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Mon, 7 Nov 2011 23:38:52 +0000 (00:38 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
arm: jadecpu: Readd MACH_TYPE_JADECPU
at91: defined mach-types for otc570 board in board config file
at91: defined mach-types for meesc board in board config file
mx31pdk: Enable D and I caches
ehci-mxc: remove incorrect comment
README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
mx53: Turn off child clocks before reconfigure perclk_root
qong: enable support for compressed images
imx: imx31_phycore.h: fix checkpatch warnings
vision2: Remove unused get_board_rev function
mx53smd: Remove unused get_board_rev function
mx53ard: Remove unused get_board_rev function
mx53evk: Remove unused get_board_rev function
mx53evk: Add RTC support
mx53loco: Remove unused get_board_rev function
mx53evk: Remove unneeded '1' from mx53evk.h
OMAP3: mvblx: Initial support for mvBlueLYNX-X
ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
omap3: mem: Move comments next to definitions
omap3: mem: Clean-up whitespaces
omap3: mem: Define and use common macros
Davinci: ea20: added PREBOOT to configuration
Davinci: ea20: added I2C support
Davinci: ea20: added video support
VIDEO: davinci: add framebuffer to da8xx
ARM: Davinci: added missing registers to hardware.h
Davinci: ea20: add gpios for LCD backlight control
Davinci: ea20: add gpio for keeping power on in board_late_init
Davinci: ea20: Add default U-Boot environment
Davinci: ea20: Add early init to get early output from console
Davinci: ea20: Add NAND support
Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
Davinci: ea20: set console on UART0
arm, davinci: add cam_enc_4xx support
arm926ejs, davinci: add missing spi defines for dm365
arm926ejs, davinci: add cpuinfo for dm365
arm, davinci: add lowlevel function for dm365 soc
arm, davinci: add header files for dm365
spl, nand: add 4bit HW ecc oob first nand_read_page function
arm, davinci: add support for new spl framework
spl: add option for adding post memory test to the SPL framework
net, davinci_emac: make clock divider in MDIO control register configurable
arm, usb, davinci: make USBPHY_CTL register configurable
usb, davinci: add enable_vbus() weak function
omap3evm: fix errors caused by multiple definitions
omap3evm: Add (quick) configuration for NAND only
omap3evm: Add (quick) configuration for MMC/SD only
omap3evm: move common config options to new file
omap3evm: Prepare to split configuration
omap3evm: Reorder related config options
omap/spl: actually enable the console
davinci_emac: compilation fix, phy is array now
omap3evm: Set environment variable 'ethaddr'
arm, arm926: fix missing symbols in NAND_SPL mode
arm, davinci: Add function lpsc_syncreset()
arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
arm/km: portl2 environment address update to P1B
arm/km: adapt bootcounter evaluation
arm/km: enable jffs2 cmds
arm/km: trigger reconfiguration for the Xilinx FPGA
arm/km: add boardid and hwkey to kernel command line
ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
netspace_v2: enable I2C EEPROM support
netspace_v2: fix SDRAM configuration
armada100: define CONFIG_SYS_CACHELINE_SIZE
pantheon: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: drop empty asm-offsets.s file
arm/km/mgcoge3un: enhance "waitforne" feature
arm/km: add variable waitforne to mgcoge3un
gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
ARM: dreamplug: fix compilation
ARM: DockStar: fix compilation
ARM: netspace_v2: fix warnings
am335x: Drop board_sysinfo struct
am335x: Temporarily add MACH_TYPE define
misc:pmic:samsung Enable PMIC driver at C210 Universal target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
smdkv310: use macro for mmc data read function address
smdkv310: use spl framework for mmc spl
SMDKV310: use get_ram_size() to validate dram size
SMDKV310: Initialize board id using CONFIG_MACH_TYPE
ORIGEN : use absolute paths and fix tool naming
ORIGEN : enable device tree support
MX25: tx25: Fix building due to missing MACH_TYPE
mx31: Add board support for HALE TT-01
mx31: add ESD control registers
mx31: define pins and init for UART2 and CSPI3
MX35: add support for flea3 board
MX51: vision2: add MACH_TYPE in config file
vision2: Remove unused header file
mx51evk: Remove unused get_board_rev function
mx51evk: Remove unneeded '1' from mx51evk.h
I2C: Fix mxc_i2c.c problem on imx31_phycore
mx35pdk: Add RTC support
mx51evk: Use GPIO API for configuring the IOMUX
mx51evk: Add RTC support
rtc: Make mc13783-rtc driver generic
qong: remove unneeded IOMUX settings
qong: Use mx31_set_gpr to setup USBH2 pins
mx31: Introduce mx31_set_gpr function
mx31pdk: Add MC13783 PMIC support
qong: remove unneeded "1" from qong.h
misc: pmic: fix regression in pmic_fsl.c (SPI)
mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
MX35: Drop unnecessary prototypes from imx-regs.h
I2C: added I2C-2 and I2C-3 to MX35
MX35: factorize common assembly code
MX35: add reset cause as provided by other i.MX
MX35: add pins definition for UART3
MX35: added ESDC structure to imx-regs
Wolfgang Denk [Mon, 7 Nov 2011 23:37:27 +0000 (00:37 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-coldfire
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire: The EB+MCF-EV123 boards config update
ColdFire: Fix the compile issue for M52277
ColdFire:Moving the remaining coldfire boards to boards.cfg
Fix:
spi.c: In function 'spi_init_r':
spi.c:279:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
spi.c: In function 'spi_xfer':
spi.c:361:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Sat, 5 Nov 2011 05:13:04 +0000 (05:13 +0000)]
common/cmd_flash.c: Fix GCC 4.6 build warnings
Fix:
cmd_flash.c:355:32: warning: 'info' may be used uninitialized in this
function [-Wuninitialized]
cmd_flash.c:354:10: warning: 'sect_first' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c:354:10: warning: 'sect_last' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c: In function 'do_protect':
cmd_flash.c:540:9: warning: 'info' may be used uninitialized in this
function [-Wuninitialized]
cmd_flash.c:538:9: warning: 'sect_first' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c:538:9: warning: 'sect_last' may be used uninitialized in
this function [-Wuninitialized]
Wolfgang Denk [Sat, 5 Nov 2011 05:13:03 +0000 (05:13 +0000)]
drivers/net/rtl8139.c: Fix GCC 4.6 build warnings
Fix:
rtl8139.c: In function 'rtl8139_probe':
rtl8139.c:256:15: warning: variable 'fullduplex' set but not used
[-Wunused-but-set-variable]
rtl8139.c:256:6: warning: variable 'speed10' set but not used
[-Wunused-but-set-variable]
rtl8139.c: In function 'rtl_transmit':
rtl8139.c:419:16: warning: variable 'txstatus' set but not used
[-Wunused-but-set-variable]
Change code to use new debug macros; also fix the new errors and
warnigns popping up now, like "error: 'to' undeclared" and some
"warning: format '%X' expects argument of type 'unsigned int', but
argument X has type 'long unsigned int'"
Wolfgang Denk [Sat, 5 Nov 2011 05:13:00 +0000 (05:13 +0000)]
board/mousse/flash.c: Fix GCC 4.6 buil warnings
Fix:
flash.c: In function 'flash_erase':
flash.c:780:18: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
flash.c:779:11: warning: variable 'addr' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:56:00 +0000 (15:56 +0000)]
board/alaska/flash.c: Fix GCC 4.6 build warnings
Fix:
flash.c: In function 'flash_erase':
flash.c:409:21: warning: variable 'last' set but not used
[-Wunused-but-set-variable]
flash.c:408:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:669:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data_block':
flash.c:709:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:57 +0000 (15:55 +0000)]
mpc8260/i2c.c: replace PRINTD() by debug()
This also fixes some GCC 4.6 build warnings like:
i2c.c: In function 'i2c_init':
i2c.c:221:26: warning: variable 'txbd' set but not used
[-Wunused-but-set-variable]
i2c.c:221:19: warning: variable 'rxbd' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:56 +0000 (15:55 +0000)]
mpc8260/i2c.c: CodingStyle cleanup
Make (mostly) checkpatch clean (don't convert to use I/O accessors
yet, so there will be "Use of volatile is usually wrong" warnings
left. Also accept some other harmless checkpatch warnings.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:52 +0000 (15:55 +0000)]
mpc8260/speed.c: Fix GCC 4.6 build warnings
Fix:
speed.c: In function 'get_clocks':
speed.c:113:30: warning: variable 'cpmdf' set but not used
[-Wunused-but-set-variable]
speed.c:113:23: warning: variable 'busdf' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:51 +0000 (15:55 +0000)]
TQM850M: Add missing CONFIG_BOOTDELAY
This also fixes a build warning:
main.c: In function 'main_loop':
main.c:311:16: warning: variable 'bootlimit' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:47 +0000 (15:55 +0000)]
board/rbc823/flash.c: Fix flash initalization
The RBC823 has only one NOR flash bank. Remove all code trying to
deal with a second bank. This also fixes a number of GCC 4.6 build
warnings:
flash.c: In function 'flash_init':
flash.c:62:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:63:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:66:12: warning: array subscript is above array bounds
[-Warray-bounds]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:44 +0000 (15:55 +0000)]
board/mbx8xx/mbx8xx.c: Fix GCC 4.6 build warnings
Fix:
mbx8xx.c: In function 'mbx_init':
mbx8xx.c:127:15: warning: variable 'refclock' set but not used
[-Wunused-but-set-variable]
mbx8xx.c: In function 'board_get_cpufreq':
mbx8xx.c:231:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
mbx8xx.c: In function 'get_reffreq':
mbx8xx.c:242:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:43 +0000 (15:55 +0000)]
mpc8xx/spi.c: Fix GCC 4.6 build warnings
Fix:
spi.c: In function 'spi_init_f':
spi.c:144:21: warning: variable 'iop' set but not used
[-Wunused-but-set-variable]
spi.c:142:22: warning: variable 'cpi' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:41 +0000 (15:55 +0000)]
board/genietv/flash.c: Fix flash initialization
The GENIETV has only one NOR flash bank. Remove all code trying to
deal with a second bank. This also fixes a number of GCC 4.6 build
warnings:
flash.c:65:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:66:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:69:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:183:2: warning: format '%x' expects argument of type 'unsigned
int', but argument 2 has type '
Wolfgang Denk [Fri, 4 Nov 2011 15:55:39 +0000 (15:55 +0000)]
board/etx094/flash.c: Fix flash initialization
The ETX094 has only one NOR flash bank. Remove all code trying to
deal with a second bank. This also fixes a number of GCC 4.6 build
warnings:
flash.c: In function 'flash_init':
flash.c:68:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:70:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:72:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:128:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:129:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:133:12: warning: array subscript is above array bounds
[-Warray-bounds]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:37 +0000 (15:55 +0000)]
mpc8xx/i2c.c: replace PRINTD() by debug()
This also fixes some GCC 4.6 build warnings like:
warning: variable 'txbd' set but not used [-Wunused-but-set-variable]
warning: variable 'rxbd' set but not used [-Wunused-but-set-variable]
Signed-off-by: WOlfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Fix:
pcmcia.c: In function 'pcmcia_hardware_enable':
pcmcia.c:22:21: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
pcmcia.c: In function 'pcmcia_hardware_disable':
pcmcia.c:130:25: warning: variable 'pcmp' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:30 +0000 (15:55 +0000)]
board/netta/pcmcia.c: Fix GCC 4.6 build warnings
Fix:
pcmcia.c: In function 'cfg_ports':
pcmcia.c:151:21: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:150:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
pcmcia.c: In function 'pcmcia_hardware_enable':
pcmcia.c:179:25: warning: variable 'sysp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:177:21: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:176:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
pcmcia.c: In function 'pcmcia_hardware_disable':
pcmcia.c:271:25: warning: variable 'pcmp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:270:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
pcmcia.c: In function 'pcmcia_voltage_set':
pcmcia.c:303:9: warning: variable 'sreg' set but not used
[-Wunused-but-set-variable]
pcmcia.c:300:21: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:29 +0000 (15:55 +0000)]
board/netta/codec.c: Fix GCC 4.6 build warnings
Fix:
codec.c: In function 's_write_BR':
codec.c:1389:15: warning: variable 'v' set but not used
[-Wunused-but-set-variable]
codec.c: In function 's_write_OR':
codec.c:1400:15: warning: variable 'v' set but not used
[-Wunused-but-set-variable]
codec.c: In function 's_write_NR':
codec.c:1411:15: warning: variable 'v' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:28 +0000 (15:55 +0000)]
board/mbx8xx/pcmcia.c: Fix GCC 4.6 build warnings
Fix:
pcmcia.c: In function 'pcmcia_hardware_enable':
pcmcia.c:83:25: warning: variable 'sysp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:81:21: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:80:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
Fix:
pcmcia.c: In function 'pcmcia_voltage_set':
pcmcia.c:158:25: warning: variable 'pcmp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:157:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:26 +0000 (15:55 +0000)]
board/lwmon/pcmcia.c: Fix GCC 4.6 build warnings
Fix:
pcmcia.c: In function 'pcmcia_hardware_enable':
pcmcia.c:33:21: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:32:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
pcmcia.c: In function 'pcmcia_voltage_set':
pcmcia.c:174:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
Fix:
../common/pcmcia.c: In function 'pcmcia_hardware_enable':
../common/pcmcia.c:23:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
../common/pcmcia.c: In function 'pcmcia_voltage_set':
../common/pcmcia.c:152:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Klaus Heydeck <heydeck@kieback-peter.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:24 +0000 (15:55 +0000)]
board/icu862/pcmcia.c: Fix GCC 4.6 build warning
Fix:
pcmcia.c: In function 'cfg_port_B':
pcmcia.c:21:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
pcmcia.c: In function 'pcmcia_hardware_enable':
pcmcia.c:50:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
pcmcia.c: In function 'pcmcia_voltage_set':
pcmcia.c:191:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:21 +0000 (15:55 +0000)]
mpc8xx/fec.c: Fix GCC 4.6 build warnings
Fix:
fec.c: In function 'fec_pin_init':
fec.c:381:18: warning: variable 'fecp' set but not used
[-Wunused-but-set-variable]
fec.c: In function 'fec8xx_miiphy_write':
fec.c:1013:8: warning: variable 'rdreg' set but not used
[-Wunused-but-set-variable]
Note: The code was slightly rearranged, but no functional changes
attempted, i. e. no conversion to use I/O accessors.
Silence this warning:
cfb_console.c: In function 'video_logo':
cfb_console.c:1563:18: warning: variable 'y_off' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
Fix:
cam5200_flash.c: In function 'flash_erase_32':
cam5200_flash.c:282:24: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
cam5200_flash.c: In function 'flash_erase_16':
cam5200_flash.c:612:24: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:16 +0000 (15:55 +0000)]
PM520: add missing enable_interrupts()
The code disabled interrupts in several locations, without re-enabling
them again. Fix this.
While we are at it, also fix a GCC 4.6 build warning:
flash.c: In function 'flash_erase':
flash.c:373:21: warning: variable 'last' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Josef Wagner <Wagner@Microsys.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:13 +0000 (15:55 +0000)]
drivers/rtc/rv3029.c: fix GCC 4.6 build warnings
Fix:
rv3029.c: In function 'rtc_set':
rv3029.c:98:6: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
rv3029.c: In function 'set_eere_bit':
rv3029.c:131:6: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
rv3029.c: In function 'wait_eebusy':
rv3029.c:149:9: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
rv3029.c: In function 'rtc_reset':
rv3029.c:165:6: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
Fix:
auto_update.c: In function 'do_auto_update':
auto_update.c:344:48: warning: variable 'got_ctrlc' set but not used
[-Wunused-but-set-variable]
auto_update.c:344:18: warning: variable 'bitmap_first' set but not
used [-Wunused-but-set-variable]
Fix:
cmd_stk52xx.c: In function 'spi_transmit':
cmd_stk52xx.c:85:6: warning: variable 'dummy' set but not used
[-Wunused-but-set-variable]
cmd_stk52xx.c: In function 'i2s_play_wave':
cmd_stk52xx.c:199:3: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
Wolfgang Denk [Fri, 4 Nov 2011 15:55:07 +0000 (15:55 +0000)]
arch/powerpc/lib/board.c: make (mostly) checkpatch-clean
CodingStyle cleanup.
Accepted (in this cleanup) checkpatch messages:
- externs should be avoided
(to be cleaned up later)
- no spaces at the start of a line
(accepted in multi-line #if's)
- Macros with complex values
(false reports)
- do not use assignment in if condition
(accepted in one place, where avoiding it would have required an
additional level of nesting, resulting in less readable code)
projects / karo-tx-uboot.git / log